主成分-偏最小二乘动力学分光光度法同时测定农药两组分

对氨基甲酸酯杀虫剂残杀威（PRO）和异丙威（ISO）的速差动力学光度法同时测定进行了研究。残杀威和异丙威均能在碱性条件下发生水解，水解生成的酚盐，均可以与对氨基苯酚及高碘酸钾混合物发生反应生成兰色化合物，且这是一个反应速率适中的动力学反应。本实验在538nm-700nm采集多个时间点下多个波长的动力学－－吸收光谱数据，构成量测矩阵。采用主成分－偏最小二乘法（PC－PLS）对测定数据进行了解析。本文对环境水样中残杀威和异丙威的含量进行了测定。取得了较好的分析结果。从而提出了一种易于实现，准确度高的残杀威和异丙威的同时测定新方法。     

分光光度法测定果蔬中残杀威残留量

在碱性条件下残杀威水解生成酚盐,在盐酸介质中对氨基苯磺酸与亚硝酸根发生重氮化反应,上述所得酚盐和重氮化产物在氨性溶液中偶联生成偶氮染料,此偶联产物的最大吸收波长为427nm,据此提出了分光光度法测定果蔬中残杀威含量的方法。残杀威的质量浓度在0.17～2.04mg·L-1范围内与其吸光度呈线性关系,检出限(3s/k)为0.03mg·L-1。方法用于测定果蔬中残杀威的含量,相对标准偏差(n=5)在0.3%～0.7%之间,加标平均回收率为96%。     

气相色谱-串联质谱法测定乌龙茶中5种氨基甲酸酯类农药

建立了乌龙茶中5种氨基甲酸酯农药(速灭威、异丙威、仲丁威、残杀威和抗蚜威)同时测定的气相色谱-串联质谱(GC-MS/MS)分析方法。样品经正己烷-乙酸乙酯(1∶1)混合溶液提取后,通过400 mg PSA/400 mg C18/1 200 mg Mg SO4的Qu ECh ERS试剂盒进行净化,Rxi-5 Sil MS毛细管柱(30 m,0.25 mm×0.25μm)进行分离,串联质谱进行定性定量分析。5种农药在各自的线性范围(速灭威和残杀威为5~500μg/kg,异丙威、仲丁威和抗蚜威为1~500μg/kg)内具有良好的线性关系,相关系数(r2)均大于0.99;在5,20,100μg/kg 3个加标水平下,速灭威和残杀威的平均回收率为77.5%~95.4%,相对标准偏差(RSD,n=6)为2.1%~6.1%,检出限和定量下限分别为1μg/kg和5μg/kg;在1,20,100μg/kg 3个加标水平下,异丙威、仲丁威和抗蚜威的平均回收率为79.5%~102.5%,RSD为2.0%~8.2%,检出限和定量下限分别为0.2μg/kg和1μg/kg。该方法操作简单、灵敏度高、重现性好,可满足乌龙茶样品中5种氨基甲酸酯类农药残留的分析要求。     

月桂酸胶束电动毛细管色谱快速测定氨基甲酸脂类农药的研究

以月桂酸表面活性剂和氨水组成缓冲溶液,建立了毛细管胶束电动色谱快速测定七种氨基甲酸脂类农药的方法。对电泳介质的种类及浓度、pH值、操作电压和进样时间等影响因素进行了优化,以45 mmol/L月桂酸(乙醇溶)和120 mmol/L氨水(用0.1 mol/L NaOH调至pH=9.5)为电泳介质,在4.5 min内实现对速灭威、残杀威、克百威、抗蚜威、异丙威、硫双威、双氧威的分离检测。结合固相萃取(SPE)对农田水样进行测定,各农药检出限为2.0～15μg/L,回收率为85%～107%,相对标准偏差为4.3%～8.3%。     

高效液相色谱电化学安培法同时测定大米中4种氨基甲酸酯农药残留量

报道了用液相色谱法测定微量氨基甲酸酯农药的方法，氨基甲酸酯先在碱性条件水解，生成的酚用液相色谱安培法测定。研究了最优色谱条件。该法简单、快速、灵敏，已应用于测定大米中克百威、西维因、异丙威和甲硫威４种氨基甲酸酯农药残留量。     

甲氧基萘的磺化反应

以三甲基硅氯磺酸酯为磺化剂，进行了单和双甲氧基萘的磺化反应研究。用１ＨＮＭＲ测定磺化产物的组成。比较了磺化剂种类和用量对磺化反应的影响。发现了磺化反应中的成酐现象，研究了１，６－二甲氧基萘进行反应时二磺化产物的生成动力学。     

动力学分光光度法结合化学计量学同时测定农药杀线威和抗蚜威

本文采用动力学分光光度法结合化学计量学方法对水样中的两种氨基甲酸酯类农药杀线威和抗蚜威进行测定.该方法基于酸性条件下,Cu(Ⅱ)能催化H2O2氧化罗丹明B而使其褪色,杀线威或抗蚜威存在时能使该反应速率降低,而且两者对反应速率的影响存在一定差异.实验对硫酸浓度、Cu(Ⅱ)浓度、罗丹明B浓度、H2O2的质量分数以及温度等条件进行考察.在选定实验条件下,杀线威和抗蚜威测定的线性范围分别为2～16μg·mL-1和1～15μg·mL-1,检测限分别为0.65μg·mL-1和0.41 μg·mL-1.实验采集波长554 nm处和反应时间0～600 s范围内动力学吸光度数据,并分别采用偏最小二乘法(PLS)和主成分回归法(PCR)处理,建立了定量回归模型并对合成样品进行测定以验证模型.该方法可应用于实际水样中杀线威和抗蚜威的同时测定.     

液相法苯选择加氢制环己烯催化反应动力学方程

 测定了Ru－M－B／ZrO2催化剂上选择加氢制环己烯反应过程中苯、环己烯及环己烷浓度随时间变化的c～t曲线，获得了苯选择加氢制环己烯反应中各步反应的级数和速率常数等动力学参数．结果给出，苯转化的反应级数对苯为1，对氢低压下为2，高压下为0；环己烯继续加氢生成环己烷的反应级数对环己烯为0，对氢低压下为2，高压下为0．在此基础上建立了苯选择加氢制环己烯各步反应的动力学方程，并对动力学方程进行了验证．     

AgBiS2/Bi2S3分子印迹光电化学传感器用于测定残杀威

构建了一种基于AgBiS₂/Bi₂S₃的分子印迹光电化学传感器,用于杀虫剂残杀威的检测。采用溶剂热法,在钛片基底上合成AgBiS₂/Bi₂S₃复合材料。以残杀威为模板分子,邻苯二胺为功能单体,通过电聚合在修饰AgBiS₂/Bi₂S₃复合材料的钛片上电沉积形成分子印迹聚合物膜,可对残杀威产生特异性识别。残杀威与印迹孔穴特异性结合后,阻碍电子供体穿过孔穴到达电极表面,导致光电流降低,据此进行残杀威的检测。残杀威浓度的对数值与光电流在1.0×10^-12～5.0×10^-10 mol/L范围内呈线性关系,检出限为2.3×10^-13 mol/L。将此传感器用于水果等实际样品中残杀威残留的检测,加标回收率介于101.0%～103.1%之间。     

FTIR法研究乙酸酚醛酯固化邻甲酚环氧树脂的反应动力学

用ＦＴＩＲ原位测量技术研究了乙酸酚醛酯与邻甲酚环氧树脂在２－甲基咪唑存在下进行恒温固化反应的动力学，测定了固化反应的动力学参数，研究结果表明，固化反应是按照一级固化反应动力学进行的，根据羰基峰在固化反应前后的变化对固化反尖机理进行了初步探讨。     

Application of GRAM and TLD to the resolution and quantitation of real complex multicomponent mixtures by fluorescence spectroscopy

The application of the generalised rank annihilation method (GRAM) and the trilinear decomposition (TLD) method to the resolution and quantitation of fluorescence excitation-emission matrices of a ternary mixture of pesticides, carbendazim, fuberidazole, and thiabendazole, with overlapped spectra is described. The results obtained with both methods are compared and evaluated using measures of similarity (correlation coefficients) between the real and estimated spectra. Both approaches have been tested using augmented data matrices containing only two samples, but none of these methods succeeded completely in resolution of the system. When TLD was applied to augmented data matrices containing more than two samples better performance was achieved. To illustrate the application of both algorithms to real samples, they were used in the analysis of water samples containing the target pesticides. Again, TLD had an advantage over GRAM because the ability to analyse data from multiple (more than two) samples simultaneously allowed the resolution of the mixtures.     

Pressurized liquid extraction of organochlorine pesticides from certified solid materials

In order to propose a versatile method to use in laboratories devoted to environmental analysis, a scheme for the determination of organochlorine pesticides from different solid matrices is evaluated. Pressurized liquid extraction is chosen as the sample preparation technique, followed by the purification of the extract by means of solid-phase extraction with Envi-carb cartridge (100 m(2)/g). Finally, the extracts are analyzed by programmed temperature vaporization (PTV)-gas chromatography (GC)-electron-capture detection and PTV-GC-mass spectrometry. The suitability of the method for the analysis of different matrices is determined by the extraction and analysis of four certified reference materials of solid matrices: CRM 804-050 (soil), SRM 1941b (organics in marine sediment), SRM 1944 (New York/New Jersey waterway sediment) and SRM 1649a (Urban Dust). Good statistical concordance between the results obtained and the certified or reference concentration are observed for most of the analyzed pesticides.     

A new multi-residue method for analysis of pesticide residues in fruit and vegetables using liquid chromatography with tandem mass spectrometric detection

A new multi-residue method for determination of pesticide residues in a wide variety of fruit and vegetables, using the National Food Administration (NFA) ethyl acetate extraction and determination by means of LC-MS/MS, is presented. The method includes pesticides normally detected by LC-UV or LC-fluorescence such as benzimidazoles, carbamates, N-methylcarbamates and organophosphorus compounds with an oxidisable sulphide group as well. After extraction with ethyl acetate, the extract is concentrated and an aliquot of the extract is evaporated to dryness and redissolved in methanol before injection on LC-MS/MS. The method has been validated for 57 different pesticides and metabolites. Representative species from different commodity groups were chosen as matrices in order to study the influence from different matrices on recoveries. The fortification levels studied were 0.01-0.5 mg kg(-1). Matrix effects were tested for all matrices by means of standard addition to blank extracts. The matrix effect, expressed as signal in solvent compared to signal in matrix, was in general found to be small. The obtained recoveries are, with a few exceptions, in the range 70-100%. The proposed method is quick and straightforward and no additional clean-up steps are needed. The method can be used for the analysis of all 57 pesticides in one single determination step at 0.01 mg kg(-1).     

Alternative calibration approaches to compensate the effect of co-extracted matrix components in liquid chromatography-electrospray ionisation tandem mass spectrometry analysis of pesticide residues in plant materials

The aim of this study was to evaluate the applicability of different calibration approaches in a multi- and single-residue analysis of modern pesticides in plant matrices using liquid chromatography-electrospray mass spectrometry (HPLC-ESI-MS). In the first set of experiments the determination of eight pesticides representing different groups of polar/unstable pesticides (carbamates, benzimidazoles, azoles, benzoylphenylurea) in apple samples was performed. The trueness and precision of data obtained by using: (i) external solvent standard calibration, (ii) external matrix-matched standard calibration and (iii) echo-peak internal standard calibration was compared. The last mentioned method is a novel technique providing the possibility to inject internal standard of the same identity as a target analyte, so that its retention time is close to the analyte from the sample. According to expectation, when using external standard solvent calibration the results were under- or overestimated due to suppression or enhancement of analyte's signal by matrix components. On the other hand with the use of matrix-matched calibration accurate data were obtained. With echo-peak technique accurate results comparable to those obtained by matrix calibration were obtained for six out of eight pesticides. In the second set of experiment we used the echo-peak technique to overcome the problem with the response instability in the analysis of chlormequat in pear concentrate samples. As an internal standard method the echo-peak technique provided the possibility of monitoring of signal decrease during the analytical sequence and to compensate this decrease by relating sample peak area relatively to this internal standard.     

High-throughput determination of pesticide residues in food commodities by use of ultra-performance liquid chromatography–tandem mass spectrometry

A rapid, simple, and sensitive multiresidue method for analysis of 53 pesticides in fruit and vegetables by ultra-performance liquid chromatography (UPLC) coupled to triple-quadrupole tandem mass spectrometry (MS-MS) has been developed and validated. Prior to analysis, analytes were extracted by use of buffered QuEChERS (quick, easy, cheap, effective, rugged, safe) methodology without further cleanup for non fatty matrices. Chromatographic conditions were optimised in order to achieve a fast separation in multiple reaction monitoring (MRM) mode. Indeed, more than 50 pesticides can be separated in less then 10 min. Four common representative matrices (cucumber, orange, strawberry, and olive) were selected to investigate the effect of different matrices on recovery and precision. Mean recoveries ranged from 70 to 109% with relative standard deviations lower than 20% for all the pesticides assayed in the four selected matrices. The method has been applied to the analysis of 200 vegetable samples, and imidacloprid was the pesticide most frequently found, with concentrations ranging from 0.01 to 1.00 mg kg⁻¹. This methodology combines the advantages of both QuEChERS and UPLC-MS-MS producing a very rapid, sensitive, and reliable procedure which can be applied in routine analytical laboratories.     

Determination of selected pesticides by GC with simultaneous detection by MS (NCI) and μ-ECD in fruit and vegetable matrices

A gas chromatography–mass spectrometry method in negative chemical ionization mode has been developed incorporating simultaneous detection using a micro-electron capture detector (μ-ECD) for the determination of pesticides in fruits and vegetables. This instrument configuration uses a three-way splitter device which divides the effluent from the analytical column between the two detectors with the split ratio 1:0.1 (MSD/μ-ECD) in each run. The μ-ECD was used for confirmation purposes. Validation of the method was performed on three matrices: tomato, apple, and orange. The ethyl acetate method was assayed; recovery studies were performed at 10 and 100 μg/kg. Recoveries between 70% and 120% were achieved and relative standard deviations lower than 20% (n = 5) were obtained for all pesticides and matrices studied. Limits of quantification lower than 10 μg/kg were obtained for 100% of pesticides in all of the matrices. Limits of quantification lower than 2.5 μg/kg were achieved for 77.8% of pesticides in the tomato and apple matrices, and for 72.2% of pesticides in the orange matrix. The method showed linear response in the concentration range tested (2.5–500 μg/kg) with correlation coefficients >0.99. Good repeatability and reproducibility results were obtained in all cases, with relative standard deviations lower than 16.7% and 20%, respectively. Finally, 20 incurred samples were analyzed using the proposed method. The simultaneous use of the two detectors was satisfactory for the analysis of these real samples. The total number of pesticides identified was 25. The number of samples which contained at least one pesticide was 15—this represented 75% of the total number of samples studied.     

Studies of pesticides by collision-induced dissociation, postsource-decay, matrix-assisted laser desorption/ionization time of flight mass spectrometry

The use of collision-induced dissociation, postsource decay (CID-PSD) matrix-assisted laser desorption/ionization (MALDI) mass spectrometry for the analysis of small organic molecules is demonstrated. Three pesticides: paraquat, diquat, and difenzoquat were chosen for this study. The matrices 2,5-dihydroxybenzoic acid (DHB), alpha-cyano-4-hydroxycinnamic acid (alpha-CHCA), and sinapinic acid (SA) were selected to investigate the effect of the matrix on the CID-PSD MALDI spectra of these molecules. Alpha-CHCA and DHB were found to be appropriate matrices for the pesticides studied. Spectra for a given pesticide obtained from different matrices were compared with each other, and the differences between them are discussed. A comparison of CID-PSD MALDI with fast-atom bombardment MS/MS spectra is presented; the agreement of pesticide fragmentation patterns between the two methods indicates that CID-PSD MALDI MS is a reliable and efficient technique for structural elucidation of small molecules.     

Potential applicability of MALDI-MS for low-molecular-weight pesticide determination

The application of matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) for pesticide analysis was demonstrated. Fifteen pesticides were chosen as the model pesticides and twenty-six MALDI matrices were screened for the most suitable matrix. Under the optimized conditions, the obtained limits of detections were lower than the maximum residue limit values stated with 12 pesticides out of 15 tested. The proposed methodology showed a good analytical performance in terms of rapid, good sensitivity and high throughput of the method as an alternative method for pesticide residues evaluation.     

Comparison of Extraction Methods by Soxhlet, Sonicator, and Microwave in the Screening of Pesticide Residues from Solid Matrices

Three types of solvent extraction methods (by soxhlet, sonicator and microwave) for pesticide recoveries in solid matrices were compared and evaluated using the standard addition method. Variables (solvent and extraction time) for the optimization of microwave assisted extraction (MAE) were also studied. Three organochlorine pesticides (BHC, DDE, and Dildrin) were chosen for this particular study because of their great presence in the soil where the samples were collected and their positive association with the risk of breast cancer. Comparison of the results obtained indicates that the efficiency of extraction varies, depending on the matrices and the pesticides analyzed. The study focused on the variation in the extraction quantities of different methods in different matrices. The extraction conditions were optimized for MAE with a single matrix (bark) and applied to the rest in order to study the variability in results. Gas chromatography with an electron capture detector (GC–ECD) was used for analysis of the extracts. The results show that even though the use of MAE improved extraction in some of the matrices studied, the extraction method must be optimized whenever a new matrix is evaluated. A statistical comparison indicated that pesticide recoveries and method reproducibility of microwave extraction compared less favorably with the conventional soxhlet method in some of the matrices, whereas the sonicator method was not found to be as efficient as the others.     

Use of SPME extraction to determine organophosphorus pesticides adsorption phenomena in water and soil matrices

Solid-phase micro extraction (SPME) coupled with GC enables rapid and simple analysis of organophosphorus pesticides in a range of complex matrices. Investigations were made into the extraction efficiencies from water of six organophosphorus insecticides (methamidophos, omethoate, dimethoate, parathion methyl, malathion, and parathion ethyl) showing a wide range of polarities. Three SPME fibres coated with different stationary phases, polydimethylsiloxane, polyacrylate, and carbowax-divinylbenzene (CW-DVB), were investigated. Water was spiked with the pesticides at concentrations from 1 to 0.01 µg mL-1, and the solutions used for optimization of the procedure. The CW-DVB fibre, with a 65 µm coating, gave the best performance. The optimized experimental conditions were sample volume 10 mL at 20°C, equilibration time 16 min, pH 5, and presence of 10% w/v NaCl. SPME analyses were performed on solutions obtained by equilibrating aqueous pesticide solutions with six certified soils with various physico-chemical characteristics. SPME data were also assessed by comparison with analyses performed by using conventional solid-phase extraction. Results indicate the suitability of SPME for analysis of pesticides in environmental water samples.