Determination of Anisotropic Plastic Constitutive Parameters Using the Virtual Fields Method

The aim of the present study is to retrieve all the anisotropic plastic constitutive parameters from uniaxial loading. A complex geometry which can provide very heterogeneous stress states in a uniaxial tensile test was chosen for steel sheet specimens. A digital image correlation technique was used for the full-field heterogeneous strain measurement. The orthotropic Hill1948 yield criterion with Swift isotropic hardening was adopted as an elasto-plastic constitutive model. The virtual fields method (VFM) was employed as an inverse analytical tool to determine the constitutive parameters. All the parameters were successfully identified using the VFM by combining two tensile test results obtained in rolling and transverse directions.     

GPS在线求解载体姿态新法

介绍了求解两个GPS接收机之间基线向量的快速解算方法,并由此引出利用两个接收机来求解载体全姿态的新方法,通过仿真结果表明：此法可大大加速整周模糊度的解算速度,并且可以只利用两个接收机就能求解载体姿态。     

岩体节理刚度系数的现场声波测试

Ｇｏｏｄｍａｎ教授提出的节理单元模型被广泛地应用于岩石力学与工程实践。然而该模型的分析精度却依赖于对节理的法向刚度ｋｎ切向刚度ｋｓ的准确确定。但这项工作在实验室几乎是不可能的。文中提出了一种在现场利用声波测试ｋｎ和ｋｓ的方法，并讨论了影响ｋｎ、ｋｓ测试精度的因素。     

A Simple Method for the Determination of Angular Velocity and Acceleration of a Spherical Motion Through Quaternions

Given a quaternion representation of a spherical motion of a rigid body with respect to another body, acting as a reference frame, this contribution presents a simple and straightforward method for determining both the angular velocity and angular acceleration of the moving body with respect to the reference frame. Instead of employing orthogonal matrices or their linear invariants, this contribution makes use of quaternions avoiding, in this way, the series of matrix identities or theorems that are required in a pair of previous approaches.     

Determination of Brinkman Model Parameters Using Stokes Flow Model

Transport in Porous Media - The two key parameters of the Brinkman’s model for fluid flow in porous media—permeability and effective viscosity—are determined theoretically. The...     

同时测量几个弹性光学系数的一种简便方法

本文采用自己设计的光路,根据关于各向异性材料的几个弹性光学系数的定义,推得了它们与干涉条纹变化数的关系。以聚碳酸脂、环氧树脂及有机玻璃为例,测量了它们沿主应力σ_1及σ_2方向的折射率随外力的变化规律,从而完全得到了与它们有关的几个弹性光学系数。     

结构随机振动响应的工程简化分析

鉴于结构随机振动响应有限元分析的复杂性 ,本文提出了一种工程简化分析方法 ,以便于工程人员应用。它可以直接利用结构模型试验数据 ,从而保证分析结果具有足够的精度。     

子结构物理参数的一种识别方法

本文基于复模态综合和优化技术,提出一种子结构物理参数识别方程。该方法利用复模态综合在广义坐标下建立物理参数识别方程,然后将物理参数识别化为优化问题求解。给出了一台钻床的子结构物理参数识别实例来说明方法的有效性.     

The Dilute Rheology of Swimming Suspensions: A Simple Kinetic Model

A simple kinetic model is presented for the shear rheology of a dilute suspension of particles swimming at low Reynolds number. If interparticle hydrodynamic interactions are neglected, the configuration of the suspension is characterized by the particle orientation distribution, which satisfies a Fokker-Planck equation including the effects of the external shear flow, rotary diffusion, and particle tumbling. The orientation distribution then determines the leading-order term in the particle extra stress in the suspension, which can be evaluated based on the classic theory of Hinch and Leal (J Fluid Mech 52(4):683–712, 1972), and involves an additional contribution arising from the permanent force dipole exerted by the particles as they propel themselves through the fluid. Numerical solutions of the steady-state Fokker-Planck equation were obtained using a spectral method, and results are reported for the shear viscosity and normal stress difference coefficients in terms of flow strength, rotary diffusivity, and correlation time for tumbling. It is found that the rheology is characterized by much stronger normal stress differences than for passive suspensions, and that tail-actuated swimmers result in a strong decrease in the effective shear viscosity of the fluid.     

圆板弹塑性弯曲的简单样条积分方程法

提出了圆板弹塑性弯曲的简单样条积分方程法.以径向转角作为未知量建立积分方程并结合B样条函数进行求解.这一方法具有域积分容易处理、精度高和计算简单的优点.计算结果表明本文解与文[2]解吻合良好.     

A General Method for Estimating Dynamic Parameters of Spatial Mechanisms

Dynamic equations of motion require a large number of parameters for each element of the system. These can include for each part their mass, location of center of mass, moment of inertia, spring stiffnesses and damping coefficients. This paper presents a technique for estimating these parameters in spatial mechanisms using any joint type, based on measurements of displacements, velocities and accelerations and of external forces and torques, for the purpose of building accurate multibody models of mechanical systems. A form of the equations of spatial motion is derived, which is linear in the dynamic parameters and based on multibody simulation code methodologies. Singular value decomposition is used to find the essential parameter set, and minimum parameter set. It is shown that a simulation of a four-bar mechanism (with spherical, universal, and revolute joints) and based on the estimated parameters gives accurate response.     

用自相关法确定VITA法的门限K

研究了用ＶＩＴＡ条件采样方法壁湍猝发的门限值与壁湍流猝发平均周期之间的关系,根据用壁湍流流向脉动速度自相关函数检测得到的壁湍流猝发平均周期,确定壁,湍猝发ＶＩＴＡ条件采样的门限值Ｋ。     

Identification of Elasto-Plastic Constitutive Parameters from Statically Undetermined Tests Using the Virtual Fields Method

This paper presents an experimental validation of the use of the virtual fields method to identify the elasto-plastic behaviour of an iron specimen from full-field measurements with the grid method and a simple heterogeneous test configuration. The experimental procedure is carefully detailed since it is of primary importance to obtain good identification results. In particular, the use of two back-to-back cameras has proved essential to eliminate out-of-plane effects. Then, the procedure for extracting the elastic parameters and the parameters of a Voce’s hardening model using the virtual fields method is presented. The results are very convincing and encouraging for future developments using more complex test geometries leading to fully multi-axial stress states. It is a first step towards the development of such inverse procedures as an alternative to difficult and costly methods involving homogeneous tests using multi-axial testing machines.     

Determination of the Parameters of Hydraulic Models of the Vascular Bed by the Input Impedance Method

On the basis of hydraulic models of the vascular bed, the possibility of quantitatively estimating the resistances, inertia coefficients and compliances of model elements, as well as the changes in these parameters, from the hydraulic input impedance is evaluated. It is shown that the input impedance method makes it possible to find stable estimates for the hydraulic model parameters using the least squares method. No significant differences between the parameters of hydraulic models of the vascular bed calculated by the input impedance method and measured independently were found. The possibility of using the input impedance method to estimate the arterial response of an organ is discussed.     

基于模态缩减和模态实验数据的结构连接参数识别方法

利用在结构系统可测自由度上获得的不完备模态参数和子结构的有限元模型，根据模态缩减理论，建立了识别子结构间连接子结构参数的优化模型，采用逐次二次规划法求解，改善了测试噪声和模态截断误差的影响。该方法识别精度高、收敛速度快、计算量小，便于工程应用。     

一种航天器天文自主定轨方法

提出用星敏感器和地平仪测量星光角距作为主要观测量,用地平仪直接测量得到地心方向矢量,用间接测得的地心距离作为补充观测量,并用推广卡尔曼滤波方法来实时确定航天器的轨道。文中对系统的构成、模型的建立、以及卡尔曼滤波的方法都作了认真的仿真研究,并获得了满意的结果。     

A Procedure for Accurate One-Dimensional Strain Measurement Using the Grid Method

This paper deals with the accurate calculation of strain using the grid method. The strain field is first directly deduced from the fringe pattern without calculating the displacement field. This procedure is validated with two numerical examples. Two types of experiment are then carried out: a translation and a tensile test. It is observed that some additional fictitious strains appear in both cases. They are due to two main reasons which interact with each other: the grid defects and the displacement of the grid lines during testing. A suitable procedure is proposed to cancel out these fictitious strains. This procedure is successfully applied in two cases of fringe patterns.     

A Direct Determination of the Transient Exchange Term of Fractured Media Using a Continuous Time Random Walk Method

In two recent papers, Ntinger and Estébenet, 2000; Ntinger et al., submitted, we set-up a method allowing to compute both the transient and steady-state exchange terms between the matrix and fractured regions of a naturally fractured porous medium using continuous time random walk methods (CTRW). The goal of the present paper is to show that a new version of the CTRW algorithm provides a direct determination of the so called transient exchange function f(t) (or its Laplace transform f(s)) widely used in well test interpretation. It is shown that this function is directly linked with the probability density of the first escape time in the fractured region of a Brownian particle launched initially in the matrix region. This new interpretation allows relating directly the exchange coefficient with the mean escape time of brownian particles in the matrix. From a practical point of view, these new results allow to derive a simpler version of the CTRW method. In addition, we obtain a considerable speed up of the CTRW method for up-scaling fractured reservoirs.     

从传递函数识别振动系统物理参数的一种新方法

本文提出了一种新方法,可以从传递函数中识别出振动系统的质量矩阵、阻尼矩阵和刚度矩阵.