Electrochemical behavior of metal hydrides

Metal hydride electrodes are of particular interest owing to their potential and practical application in batteries. A large number of hydrogen storage materials has been characterized so far. This paper deals with the effect of the chemical nature and stoichiometry of specific alloy families (AB₅, A₂B, AB/AB₂ and AB₂) on the hydride stability, hydrogen storage capacity and kinetics of hydrogen sorption-desorption in the solid phase/gas and solid phase/electrolyte solution systems. Special attention has been paid towards the electrochemical properties of metal hydrides in terms of their performance in Ni-MH rechargeable alkaline cells. Electronic Publication     

铂单原子催化剂同步辐射X射线吸收谱的研究进展

相比于传统块体材料, 铂单原子催化剂(Pt SACs)具有接近100%的贵金属利用率、 优异的催化活性和均一的反应位点等优势, 近年来逐渐成为催化研究的前沿之一. 高度分散的Pt原子与载体之间的界面相互作用很大程度上决定了Pt SACs的物理和化学性能. 因此, 建立金属-载体相互作用与性能之间的内在关联机制, 对于单原子催化剂的优化设计至关重要. 得益于同步辐射光源高亮度、 高准直性和宽波谱的优势, X射线吸收谱技术在鉴别单原子催化剂的电子结构和局域配位方面的成果显著. 本文综合评述了Pt SACs X射线吸收谱的研究进展, 重点介绍了Pt与金属氧化物、 金属、 纳米碳和多孔有机框架等载体之间独特的相互作用, 以及其对性能的影响机制, 并对未来同步辐射新技术在Pt SACs的高分辨解析方面的前景进行了展望.     

Effects of alloying elements and binder on the electrochemical behavior of metal hydride electrodes in potassium hydroxide electrolyte

This investigation examines the effect of alloying elements on the charge–discharge performance of LaNi_3.6(Co+Mn+Al)_1.4 electrodes in 7 M KOH electrolyte. The activation behavior and the effect of binder content were also examined. Both half-cell and full-cell systems were employed to evaluate the electrochemical performance. Experimental results indicated that a few cycles of charge–discharge at a rate of 150 mA/g in 7 M KOH electrolyte were sufficient to activate the freshly prepared LaNi_3.6(Co+Mn+Al)_1.4 electrodes. The amount of binder affected the activation behavior, the overvoltage for hydrogen ions reduction and the discharge capacity of the MmNi_3.55Co_0.75Mn_0.4Al_0.3 electrode. In the alloy of the LaNi_3.6(Co+Mn+Al)_1.4 electrodes, a high Co content helped to promote both the capacity at a relatively low discharging rate and the cyclic life. An increase of the Al content raised the discharge voltage and improved the high rate discharge capacity, but reduced the cyclic stability. The alloy with a high Mn content required the least cathodic polarization during charging but had the lowest discharge capacity at a rather high discharging rate.     

Study on Electrocatalytic Activity of Platinum for Hydrogen Oxidation in Acidic Solution by Scanning Electrochemical Microscopy

The electrocatalytic activity of platinum for hydrogen oxidation in 0.01 M H₂SO₄ + 0.1 MNa₂SO₄ solution has been investigated by scanning electrochemical microscopy (SECM) technique. The cyclic voltammogram (CV), approach curve, area scan imaging and chronoamperometric methods have been used. The results indicate that the imaging capability of the SECM feedback mode can be used more efficiently to visually identify materials' electrocatalytic activity, compared with the approach curve method for identification of the conductive or insulating nature of a surface. The SECM imaging method has demonstrated the effects of Pt substrate potential on the electrocatalytic oxidation of hydrogen under a constant tip potential. It is found that the more positive the Pt substrate potential, the lower the electrocatalytic activity of the Pt. Furthermore, the chronoamperometric results support the variation of the electrocatalytic activity with the Pt substrate potential as well.     

Investigation of the influence of nickel content on the correlation between the hydrogen equilibrium pressure for hydrogen absorbing alloys and the capacity of MH electrodes in open and closed cells

Two series of overstoichiometric AB_2.4 alloys [(Zr_0.35Ti_0.65)(V_1.33Cr_0.4Fe_0.27)_{2– x} Ni_{0.4+ x} and (Zr_0.5Ti_0.5)(V_0.8Mn_0.8Cr_0.4)_{2– x} Ni_{0.4+ x} ], differing in the Zr to Ti ratios in group A and the presence of Mn or Fe in group B, were examined to consider the influence of various amounts of nickel on the structural parameters following the sorption of hydrogen. To predict the electrochemical behaviour of the prepared alloys as negative electrodes for Ni-MH cells, the pressure-composition isotherms (PCT) determined for the gas/solid phase system were correlated with the electrochemical pressure-composition (EPC) isotherms estimated from the rest potential of the alloy electrode. For preliminary assessment of the practical usefulness of the prepared samples, the electrodes made of all the alloys were subjected to charge/discharge measurements in a half-cell in 6 M KOH solution and the discharge capacities were estimated. Of the alloys with Fe and Mn components, the samples (Zr_0.35Ti_0.65)(V_0.93Cr_0.28Fe_0.19Ni_1.0) and (Zr_0.5Ti_0.5)(V_0.68Mn_0.68Cr_0.34Ni_0.7) provided the highest capacities. These alloys were chosen for testing the charge/discharge cycleability in closed Ni-MH cells. The reversibility of the cell with the former sample decreased significantly around the 25th cycle, whereas the discharge capacity of the cell with the latter sample remained almost unchanged during 100 cycles of testing. Electronic Publication     

平面铂电极上吸附氢原子表面扩散系数的测定

This Paper describes an experimental method that established a local Pt/Nafion interface on the Platinum Plane, so that the boundary conditions and the initial condition of the (diffusion equation about the diffusion of adsorbed hydrogen atom the platinum plane can be controlled. The average diffusion coefficient of underpotential deposition of hydrogen on a surface of platinum was obained for the first time and D=1.50 ×10-4cm2•s-1.The accuracy of the datum was discussed.     

Kinetic analysis of the hydrogen oxidation reaction on Pt-black/Nafion electrode

The hydrogen oxidation reaction on Pt-black/Nafion electrode was investigated using a rotating disk electrode and cyclic voltammetry technique. The voltammetric results demonstrated that the electrode can be prepared with good reproducibility and that Pt-black particles without direct contact with Nafion were still electrochemically active in taking part in the H-adsorption/desorption process. For hydrogen oxidation, the limiting current density was reduced by the presence of Nafion coating. The H₂ diffusion resistance in Nafion film was avoided when the film thickness was less than 0.2 μm for a Pt-black loading of 20 μg. Moreover, the uncertainties in the kinetic results were discussed.     

Impact of finite-temperature and condensed-phase effects on theoretical X-ray absorption spectra of transition metal complexes

The impact of condensed-phase and finite-temperature effects on the theoretical X-ray absorption spectra of transition metal complexes is assessed. The former are included in terms of the all-electron Gaussian and augmented plane-wave approach, whereas the latter are taken into account by extensive ensemble averaging along second-generation Car–Parrinello ab initio molecular dynamics trajectories. We find that employing the periodic boundary conditions and including finite-temperature effects systematically improves the agreement between our simulated X-ray absorption spectra and experimental measurements. © 2018 Wiley Periodicals, Inc.     

Binding energy of ruthenium submonolayers deposited on a Pt(111) electrode

We investigated the 3d_5/2 core-level binding energy of Ru in Ru nanoislands spontaneously deposited on a Pt(111) electrode [Pt(111)/Ru], and the binding energies of 3d_5/2 iodine and 1s CO adsorbed on Pt(111)/Ru by the use of X-ray photoelectron spectroscopy. Both iodine and CO were used as surface probes of the electronic properties of Pt(111)/Ru. Little difference was found in the binding energy of Ru in Pt(111)/Ru and in Ru(0001). However, the addition of Ru to Pt(111) induces major changes in the core-level binding energies of chemisorbed iodine and CO as referenced to those adsorbed on Ru(0001). We conclude that the iodine 3d_5/2 and CO 1s C core levels experience higher electronic charge on Pt(111)/Ru than on Ru(0001), suggesting a charge transfer from Pt to Ru, or to a Ru-I surface molecule within the deposit. The charge transfer from Pt to Ru is in agreement with the result of previous in situ electrochemical NMR investigations [P.K. Babu, H.S. Kim, A. Wieckowski, E. Oldfield (2003) J. Phys. Chem. B 107:7595] and confirms the general trend of reduction in the density of states of Pt due to alloying with Ru [J. McBreen, S. Mukerjee (1995) J. Electrochem. Soc. 142:3399]. Theoretical calculations are in progress to further interpret the origin of the binding-energy shifts observed in this study.Dedicated to Zbigniew Galus on the occasion of his 70th birthday     

电化学方法研究贮氢电极合金的P—C—T曲线

根据电化学和热力学的基础理论,考虑了氢气的逸度、碱液中水的活度以及碱液中水蒸汽的分压等影响因素,精确计算了金属氢化物电极反应的能斯特方程。结合三电极测试体系,建立了一套贮氢电极合金的P-C-T曲线电化学测定方法,并给出实验操作及相关参数确定的细节。该方法适用于涉及到大量实验工作的贮氢电极合金的成分优化及工艺研究。     

In situ Ru K-edge X-ray absorption spectroscopy of a high-area ruthenium dioxide electrode in a Nafion-based supercapacitor environment

Changes in the state of charge of a high-area RuO_x electrode in an operating RuO_x|Nafion|IrO_x supercapacitor were monitored in situ by time-resolved, transmission Ru K-edge X-ray absorption spectroscopy (XAS). Linear and reversible variations in the intensity of the transmitted X-ray beam as a function of time were found by fixing the energy of the incident X-ray beam, E_i, at judiciously selected values within the Ru K-edge X-ray near edge structure (XANES), while the supercapacitor was charged and discharged at constant current. The sign of the slope of these temporal signals was found to vary, depending on the value of E_i. This behavior could be rationalized based on the spectral differences between the Ru K-edge XANES of RuO_x in the fully oxidized and fully reduced states, recorded in situ from films of the material electrodeposited on a gold substrate in the fluorescence mode.This paper is dedicated to Prof. Wolf Vielstich on the occasion of his 80th birthday for his outstanding contributions to electrochemistry     

Studying the process of oxygen ionization on a porous metal hydride electrode

Problems that are connected with utilization of oxygen evolving during overcharge of the nickel oxide electrode in sealed nickel metal hydride batteries are considered. It is established experimentally that the rate of the process of oxygen reduction in conditions of forced gas supply into pores of a metal hydride electrode increases by two orders of magnitude as compared with the intensity of this process during natural convection. Up to 80% of evolved oxygen undergo ionization on a metal hydride electrode in these conditions even in a regime of forced (hour-long) charge of a model sealed nickel-metal hydride battery. The dependence of the current density of oxygen reduction at a metal hydride electrode on the filling of the electrode’s porous space by oxygen is estimated with the aid of manometric and potentiostatic methods. It is shown that practically all the oxygen ionization current is generated at the walls of gas-filled electrode pores, under thin electrolyte films, with a local current intensity of 1–3 mA cm^?2.     

Influence of surface contaminations on the hydrogen storage behaviour of metal hydride alloys

Hydrogen storage in metal hydrides is a promising alternative to common storage methods. The surface of a metal hydride plays an important part in the absorption of hydrogen, since important partial reaction steps take place here. The development of surface contaminations and their influence on hydrogen absorption is examined by means of absorption experiments and surface analysis, using X-ray photoelectron spectroscopy (XPS), thermal desorption mass spectrometry (TDMS) and secondary neutral mass spectrometry (SNMS), in this work. All investigations were carried out on a modern AB₂ metal hydride alloy, namely Ti_0.96Zr_0.04Mn_1.43V_0.45Fe_0.08. Surface analysis (SNMS, XPS) shows that long-term air storage (several months) leads to oxide layers about 15 nm thick, with complete oxidation of all main alloy components. By means of in situ oxygen exposure at room temperature and XPS analysis, it can be shown that an oxygen dose of about 100 Langmuirs produces an oxide layer comparable to that after air storage. Manganese enrichment (segregation) is also clearly observed and is theoretically described here. This oxide layer hinders hydrogen absorption, so an activation procedure is necessary in order to use the full capacity of the metal hydride. This procedure consists of heating (T = 120° C) in vacuum and hydrogen flushing at pressures like p = 18 bar. During the activation process the alloy is pulverized to particles of ∼20 μm through lattice stretches. It is shown that this pulverization of the metal hydride (creating clean surface) during hydrogen flushing is essential for complete activation of the material. Re-activation of powder contaminated by small doses of air (p ≈ 0.1 bar) does not lead to full absorption capacity. In ultrahigh vacuum, hydrogen is only taken up by the alloy after sputtering of the surface (which is done in order to remove oxide layers from it), thus creating adsorption sites for the hydrogen. This is shown by TDMS measurements with and without sputtering and oxygen exposure. Figure Investigated metal hydride before and after activation     

Spectroscopic Characterisation of a Bio-Inspired Ni-Based Proton Reduction Catalyst Bearing a Pentadentate N2S3 Ligand with Improved Photocatalytic Activity

Inspired by the sulfur-rich environment found in active hydrogenase enzymes, a Ni-based proton reduction catalyst with pentadentate N₂S₃ ligand was synthesised. When coupled with [Ru(bpy)₃]²⁺ (bpy=2,2′-bipyridine) as photosensitiser and ascorbate as electron donor in a 1:1 mixture of dimethylacetamide and aqueous ascorbic acid/ascorbate buffer, the catalyst showed improved photocatalytic activity compared with a homologous counterpart bearing a tetradentate N₂S₂ ligand. The mechanistic pathway of photoinduced hydrogen evolution was comprehensively analysed through optical transient absorption and time-resolved X-ray absorption spectroscopy, which revealed important electronic and structural changes in the catalytic system during photoirradiation. The Ni^II catalyst undergoes a photoinduced metal-centred reduction to form a Ni^I intermediate with distorted square-bipyramidal geometry. Further kinetic analyses revealed differences in charge-separation dynamics between the pentadentate and tetradentate forms.     

Studies on the role of oxidation states of the platinum surface in electrocatalytic oxidation of small primary alcohols

The role of the oxidation state of a platinum polycrystalline surface in the electrocatalytic oxidation of C₁ to C₄ primary alcohols has been studied by using electrochemical techniques, in situ FTIR spectroscopy and X-ray photoelectron spectroscopy. The results revealed that the oxidation state of the Pt surface plays a key role in the oxidation of primary alcohols, and demonstrated that the oxidation of C₁ to C₄ primary alcohols on a Pt electrode is controlled by the formation of surface oxides on the Pt electrode at different potentials. It was found that the dependence of the reaction process on the oxidation states of the platinum surface yielded similar features in the cyclic voltammogram for oxidation of different primary alcohols at a Pt electrode. According to the effects in the oxidation of primary alcohols, the surface oxides of platinum may be classified as active and poison species. The Pt surface oxides of higher oxidation states (Pt(OH)₃ and PtO₂) formed at potentials above 1.0 V (SCE) were identified as poison species, while other lower oxidation states of Pt surface oxides such as PtOH, Pt(OH)₂ and PtO may be identified as the possible active species for primary alcohol oxidation.     

铂单晶电极表面不可逆反应动力学I.Pt(100)单晶电极上甲酸氧化的现场红外反射光谱研究

运用电化学暂态方法和现场时间分辨ＦＴＩＲ反射光谱研究甲酸在Ｐｔ（１００）单晶电极上的解离吸附和氧化过程,深入认识了甲酸解离吸附的反应速率在－０．２５至０．２５Ｖ电位区间呈火山形变化的规律。根据电化学现场时间分辨红外光谱的研究结果,提出在研究反动力学时避免甲酸解离吸附干扰的方法,为进一步研究甲酸在Ｐｔ（１００）电极表面经活性中间体直接氧化至ＣＯ２的反应动力学奠定了基础。     

A dihydrogen bond between a bridging hydride and the NH proton of a coordinated dimethylamine: solid state, solution and theoretical characterization

The addition of one equivalent of dimethylamine (DMA) to the 44 valence-electron triangular cluster anion [Re₃(μ₃-H)(μ-H)₃(CO)₉]⁻ (1) affords the novel unsaturated derivative [Re₃(μ-H)₄(CO)₉(DMA)]⁻ (2, 46 valence electrons) which contains a dimethylamine molecule terminally coordinated to a cluster vertex. Theoretical calculations (DFT) reveal that in the more stable conformation the dimethylamine NH proton is directed towards the hydride bridging the opposite cluster edge in syn position, the close proximity of the ligands bound to the cluster surface allowing the formation of an unconventional N-H ? (μ-H)Re₂ hydrogen bond. The presence of this conformation in the solid state has been proven by an X-ray structural analysis of crystalline [PPh₄]2. Spectroscopic evidences (IR and NMR) indicate that the dihydrogen bond is maintained also in solution and, by the evaluation of the proton spin-lattice relaxation rates at variable temperature, a good estimate of the H ? H distance in solution has been determined.     

非金属与金属的协同作用对镁基储氢合金电化学性能的影响

用机械球磨法分别以Ti、B、复合物TiB对非晶态Mg45Ti3V2Ni50储氢合金进行了表面修饰.实验结果表明,恰当比例的TiB球磨修饰对镁基储氢合金循环稳定性远好于Ti、B同比例单独修饰合金电极的效果.Mg45Ti3V2Ni50与TiB质量比为2∶1的Mg45Ti3V2Ni50-TiB(2∶1)复合合金电极的初始放电容量为529.4mAh·g-1,第50次循环放电容量仍为277.1mAh·g-1.复合物TiB中Ti、B元素之间和复合合金中合金元素与TiB之间产生了金属与非金属的协同作用,导致复合合金新的立体褶皱结构的生成,增强了修饰层与合金间的作用,Mg45Ti3V2Ni50-TiB(2∶1)合金电极表面活性增强,循环稳定性显著提高.     

优化金属磷化物电催化析氢性能的策略

日益严重的能源危机和环境污染问题使得探索清洁的可再生能源载体及减少对传统化石燃料的过度依赖成为人们面临的一项重要任务.因此,各种可持续能源如太阳能、风能、海洋能和生物质能等得到了广泛研究并取得了一定的进展.然而,这些能源因存在间歇性和不稳定性等缺点阻碍了其实际应用.近年,氢气作为一种能源载体,以其高能量密度和无碳排放的优点引起了人们的广泛关注,被认为是缓解日益严重的污染问题的最有前途的环保能源.对比目前采用的天然气热解和煤炭气化等传统制氢策略,电催化水裂解由于催化效率高,制氢纯度高和不产生温室气体,被认为是高效、环保、可持续的制氢策略.电催化水裂解由两个独立的半反应组成,分别是析氢反应和析氧反应.析氢反应作为水裂解的一个半反应,在降低制氢成本及提高产氢催化效率方面起着关键作用.然而,目前的核心问题之一是要开发高效的析氢电催化剂,以加快反应速度.目前,铂和铂基纳米材料被认为是高效的析氢电催化剂,但是其稀缺性和高成本阻碍了大规模实际应用.金属磷化物由于具有较高的本征活性并且在不同的电解质中都具有良好的电催化析氢性能,被证明是一种优良的析氢电催化剂.此外,与普通催化剂相比,金属磷化电催化剂还具有合成简便、效率高、成本低、省时等优点.本文详细介绍了近年人们在金属磷化物用于电催化析氢研究中取得的进展.首先,介绍了电催化析氢反应机理,金属磷化物的结构及作用,并对其优缺点进行了总结;随后,综述了金属磷化物的合成方法,包括后处理、原位生成和电沉积策略,并对不同方法进行了比较和讨论.此外,从元素掺杂、界面工程、空穴工程、修饰特定载体、构建特定纳米结构、设计双或多金属磷化物和其他发展的新方法等七个方面详细总结了促进金属磷化物电催化活性的多种策略,并进行了对比和讨论.最后,归纳了金属磷化物在电催化析氢应用中存在的问题和面临的挑战,并对未来的研究发展提出了展望.     

在氢气氧化反应中具有高催化活性的Pt修饰的Ni/C纳米催化剂

随着能源需求的进一步增多和化石能源的大幅度减少,新型环境友好型能源成为近十年许多科研工作者的着力点.其中,燃料电池作为一种高效率、高能量密度、环境友好型能源引起了人们的关注.氢氧燃料电池研究最早、应用最早,具有得天独厚的优势.此外,由于近些年CO2的大量排放,造成了严重的温室效应,其处理也是一个严峻的课题.谢和平课题组提出的CO2矿化发电,不仅可以处理CO2,也可以作为新型能源应用,前景广阔.而不论是氢氧燃料电池还是CO2矿化电池,其阳极反应均为氢气氧化反应(HOR).Pt作为目前仍无法取代的HOR反应催化剂,不仅全球储量有限且价格昂贵,所以,寻找一种价格低廉催化性能好的催化剂成为这些新能源进一步应用的重要课题之一.对此人们进行了大量探索,主要包括尝试不同的载体、改变金属颗粒尺寸形貌等.其中,伽伐尼置换法对于制备纳米核壳结构催化剂以及降低金属颗粒尺寸、增加比表面积均有很大帮助.基于此,本文采用浸渍法和伽伐尼置换法制备了用Pt修饰Ni/C的纳米催化剂,使得纳米级活性金属均匀分散在载体上,加之双金属效应,相对于纯Pt/C催化剂,催化能力提高.浸渍法制得Ni/C前驱体,再将其置于纯乙醇中,用H2PtCl6作为Pt源置换部分Ni,得到Pt修饰的Ni/C催化剂.XRD射线衍射测试结果表明,一般的PtNi合金由于晶格相互影响,只会出现Pt的偏移衍射峰,而该催化剂均出现明显的PtNi两种元素的衍射峰,PtNi晶格互相没有影响.循环伏安法测试结果表明,在Pt-Ni/C系列催化剂中,Pt和Ni含量不同,其电化学活性面积(ECSA)各不相同.在金属总含量一致的前提下,随着Pt含量的增加,催化剂ECSA先增加后减小,最大值为66.90 m2/g,是市售Pt/C(54.12 m2/g)的1.24倍.Tafel测试HOR/HER反应交换电流密度的结果与ECSA结果一致,而Pt-Ni/C催化剂的交换电流密度最高可达485.45 A/g,是市售Pt/C(301.91 A/g)的1.6倍.对性能较好的Pt-Ni/C催化剂进行了表征,X射线光电子能谱结果发现,该催化剂载体上只有少部分Ni的氧化物裸露在表面,大部分为Pt.而透射电镜结果表明,该催化剂纳米级活性金属颗粒尺寸一致,且均匀地分散在载体表面.综合催化剂表征和电化学性能测试结果可知,使用伽伐尼置换法得到的Pt修饰的Ni/C催化剂分散均匀、颗粒尺寸小,且由于Pt作为主要催化活性金属分散于催化剂表面,而Ni作为辅助金属并不直接参与HOR反应,使得该催化剂具有较高的电化学活性.在Pt含量较少时,由于有很多Ni在催化剂表面,且催化层厚度较大,故催化活性一般.随着Pt含量的增加和Ni含量的减少,当催化剂表面只有很少Ni及相关化合物时,由于Pt比表面积大,故活性最高.当Pt含量继续增加时,Pt在Ni表面厚度增加,很多Pt被包裹,故催化活性再次降低.