Development and validation of a new high-performance liquid chromatographic method for the loperamid hydrochloride determination in drugs

A selective, precise and new high-performance liquid chromatographic method for the analysis of loperamid hydrochloride in pharmaceutical formulations was developed and validated. The mobile phase consisting buffer (sodium-octansulphonate, triethylamine and ammonium hydroxide) in water: acetonitriie (45: 55, v/v) (pH 3.2). The absorbance was monitored with a DAD detector at 226 nm. The flow rate was 1.5 cm³ min⁻¹. The linearity (r = 0.9947) and the recovery (98.58–100.42%) were found to be satisfactory. The detection and quantitation limits were found to be 0.95 and 3.12 μg cm⁻³. The results demonstrated that the procedure was accurate, precise and reproducible. It can be suitably applied for the estimation of lopera-mid hydrochloride in pharmaceutical formulations. The article is published in the original.     

Development and validation of a high-performance thin-layer chromatographic method for determination of ofloxacin residues on pharmaceutical equipment surfaces

An HPTLC method with densitometric quantification using fluorescence at 313 nm was developed and validated for the determination of ofloxacin residue in controlling pharmaceutical equipment cleanliness. Simulated samples at a residue level of 1 mg/m2 were prepared by spreading the calculated amount of ofloxacin solution on 1, 5, and 10 dm2 stainless steel surfaces. After evaporation of the solvent, the residue was removed by two ethanol wetted cotton swabs, which were thereafter extracted with the mixture of ethanol and Na2EDTA-water solution at pH 11 for 15 min with sonication. The extract and standards were applied on HPTLC silica gel 60 plates and then developed in a horizontal developing chamber from both sides using ethanol-conc. ammonia (4+1, v/v) as the mobile phase. The mean recovery (n=6) at 1 mg/m2 from 1, 5, and 10 dm2 was 95.3, 88.6, and 89.7% with the CV values 3.78, 4.41, and 4.97%, respectively. The absolute detection limit was 0.6 ng and the quantitation limit was 2 ng, but it was shown that these can be improved by immersion of the developed plate into a solution of liquid paraffin-n-hexane (1+2, v/v) to approximately 0.25 and 0.9 ng, respectively. The LOD of the method using detection without paraffin-n-hexane was 3, 0.6, and 0.3 microg/m2 by swabbing 1, 5, and 10 dm2, respectively. The method can be applied to routine control of pharmaceutical equipment cleanliness by sampling from stainless steel surface areas of 1 to 10 dm2 with acceptable residue limit/surface of 1 mg/m2.     

Development and validation of a high-performance liquid chromatographic method for determination of eprosartan in bulk drug and tablets

A simple, precise, and accurate isocratic RP-HPLC method was developed and validated for determination of eprosartan in bulk drug and tablets. Isocratic RP-HPLC separation was achieved on a Phenomenex C18 column (250 x 4.6 mm id, 5 microm particle size) using the mobile phase 0.5% formic acid-methanol-acetonitrile (80 + 25 + 20, v/v/v, pH 2.80) at a flow rate of 1.0 mL/min. The retention time of eprosartan was 7.64 +/- 0.05 min. The detection was performed at 232 nm. The method was validated for linearity, precision, accuracy, robustness, solution stability, and specificity. The method was linear in the concentration range of 10-400 microg/mL with a correlation coefficient of 0.9999. The repeatability for six samples was 0.253% RSD; the intraday and interday precision were 0.21-0.57 and 0.33-0.71% RSD, respectively. The accuracy (recovery) was found to be in the range of 99.86-100.92%. The drug was subjected to the stress conditions hydrolysis, oxidation, photolysis, and heat. Degradation products produced as a result of the stress conditions did not interfere with detection of eprosartan; therefore, the proposed method can be considered stability-indicating.     

Development and validation of a reversed-phase ion-pair high-performance liquid chromatographic method for the determination of risedronate in pharmaceutical preparations

A stability indicating, reversed-phase ion-pair high-performance liquid chromatographic method was developed and validated for the determination of risedronate in pharmaceutical dosage forms. The determination was performed on a BDS C₁₈ analytical column (250 mm × 4.6 mm i.d., 5 μm particle size); the mobile phase consisted of 0.005 M tetrabutylammonium hydroxide and 0.005 M pyrophosphate sodium (pH 7.0) mixed with acetonitrile in a ratio (78:22, v/v) and pumped at a flow rate 1.00 mL min⁻¹. The ultraviolet (UV) detector was operated at 262 nm. The retention times of magnesium ascorbyl phosphate, which was used as internal standard and risedronate were 4.94 and 5.95 min, respectively. The calibration graph was ranged from 2.50 to 20.00 μg mL⁻¹, while detection and quantitation limits were found to be 0.48 and 1.61 μg mL⁻¹, respectively. The intra- and inter-day percentage relative standard deviations, %R.S.D., were less than 5.9%, while the relative percentage error, %E_r, was less than 0.4%. The method was applied to the quality control of commercial tablets and content uniformity test and proved to be suitable for rapid and reliable quality control.     

Development of a new high-performance liquid chromatographic method for the determination of ceftazidime

A rapid, accurate, and sensitive high-performance liquid chromatographic (HPLC) method was developed and validated for the determination of ceftazidime in pharmaceuticals. The method validation parameters yielded good results and included range, linearity, precision, accuracy, specificity, and recovery. The excipients in the commercial powder for injection did not interfere with the assay. Reversed-phase chromatography was used for the HPLC separation on a Waters C18 (WAT 054275; Milford, MA) column with methanol-water (70 + 30, v/v) as the mobile phase pumped isocratically at a flow rate of 1.0 mL/min. The effluent was monitored at 245 nm. The calibration graph for ceftazidime was linear from 50.0 to 300.0 microg/mL. The values for interday and intraday precision (relative standard deviation) were <1%. The results obtained by the HPLC method were calculated statistically by analysis of variance. We concluded that the HPLC method is satisfactory for the determination of ceftazidime in the raw material and pharmaceuticals.     

Development and validation of high-performance thin-layer chromatographic method for determination of amygdalin

ABSTRACT

A new method for the extraction and quantitative determination of amygdalin has been proposed. Accelerated solvent extraction was applied for the extraction, and reversed-phase high-performance thin-layer chromatography method was developed, validated, and applied for the determination of amygdalin in the extracts of apricot, plum, almond, and peach kernels. The chromatographic system used was RP-18 silica, as stationary phase and acetonitrile/water (50:50, v/v), as mobile phase. Densitometric scanning was performed at 210 nm. The method was validated with respect to specificity, linearity, precision, and accuracy. The results showed that the peak area responses were linear within the concentration range of 2.5–50.0 µg/spot (R² = 0.9984). The limit of quantification was 4.28 µg/spot, and the detection limit 1.28 µg/spot. The intra-day and inter-day reproducibility, in terms of %RSD, were in the range of 0.81–1.15 and 1.32–1.89, respectively. The accuracy data were in the range from 99.98 to 100.56%. The method is linear, quantitative and reproducible, and could be used as an efficient and economical green chromatographic procedure for the determination of amygdalin in the fruit kernel.     

Development and validation of a stability-indicating column high-performance liquid chromatographic assay method for determination of nebivolol in tablet formulation

A simple, precise, and accurate isocratic reversed-phase (RP) stability-indicating column high-performance liquid chromatographic (HPLC) assay method was developed and validated for determination of nebivolol in solid pharmaceutical dosage forms. Isocratic RP-HPLC separation was achieved on a Phenomenex Luna C8 (2) column (250 mm x 4.6 mm id, 5 microm particle size) using mobile phase composed of acetonitrile-pH 3.5 phosphate buffer (35 + 65, v/v) at a flow rate of 1.0 mL/min, and detection was performed at 280 nm using a photodiode array detector. The drug was subjected to oxidation, hydrolysis, photolysis, and heat to apply stress conditions. The method was validated for specificity, linearity, precision, accuracy, robustness, and solution stability. The method was linear in the drug concentration range of 40-160 microg/mL with a correlation coefficient of 0.9999. The repeatability relative standard deviation (RSD) for 6 samples was 0.69%, and the intermediate precision (RSD) for 6 samples was 1.39%. The accuracy (recovery) was between 98.57 and 99.55%. Degradation products produced as a result of stress studies did not interfere with detection of nebivolol, and the assay can thus be considered stability-indicating.     

Development and validation of a liquid chromatographic method for determination of lacidipine residues on surfaces in the manufacture of pharmaceuticals

A high-performance liquid chromatographic (HPLC) method for the assay of lacidipine residues in swabs collected from various surfaces involved in drug manufacture is described. The swabbing procedure using two cotton swabs was validated applying a wipe test. An RP-HPLC method, developed to determine low quantities of the drug in the presence of its main impurities, was also validated. To remove drug residues from stainless steel and glass surfaces, the first cotton swab must be soaked preferably in acetonitrile whereas, on vinyl surfaces better results are obtained using methanol. The HPLC method selected involves a C12 column, at 40 degrees C, a mixture of acetonitrile-0.05 M ammonium acetate (88:12, v/v) as a mobile phase and UV detection at 282 nm. Recoveries obtained are strongly dependent on the type of surface tested, being higher on stainless steel. The surface material has also different influence on the drug stability. The method was validated over a range of 0.5-100 microg/400 cm2 and had a detection limit of 0.1 microg/400 cm2.     

Development and validation of a hydrophilic interaction liquid chromatographic method for determination of aromatic amines in environmental water

A simple, precise, and accurate hydrophilic interaction liquid chromatographic (HILIC) method has been developed for the determination of five aromatic amines in environmental water samples. Chromatography was carried out on a bare silica column, using a mixture of acetonitrile and a buffer of NaH₂PO₄–H₃PO₄ (pH 1.5, containing 10 mM NaH₂PO₄) (85:15, v/v) as a mobile phase at a flow rate of 1 mL min⁻¹. Aromatic amines were detected by UV absorbance at 254 nm. The linear range of amines was good (r² > 0.998) and limit of detection (LOD) within 0.02–0.2 mg L⁻¹ (S/N = 3). The retention mechanism for the analytes under the optimum conditions was determined to be a combination of adsorption, partition and ionic interactions. The proposed method was applied to the environmental water samples. Aromatic amines were isolated from aqueous samples using solid-phase extraction (SPE) with Oasis HLB cartridges. Recoveries of greater than 75% with precision (RSD) less than 12% were obtained at amine concentrations of 5–50 μg L⁻¹ from 100 mL river water and influents from a wastewater treatment plant (WWTP). The present HILIC technique proved to be a viable method for the analysis of aromatic amines in the environmental water samples.     

Use of solid-phase extraction and high-performance liquid chromatography for the determination of triazine residues in water: validation of the method

A method for determination of some triazine residues in water has been developed. The method involves concentration with C18 solid-phase extraction cartridges followed by high-performance liquid chromatographic analysis using a C18 column with UV detection at 230 nm, a mobile phase of methanol-water (60:40, v/v) at pH 4.6 (phosphoric acid) and a flow-rate of 0.8 ml/min. After optimization of the extraction and separation conditions, the method was validated. The method can be used for determination of atrazine, simazine, cyanazine and ametryn in water, within the international limits of 0.1 microg/l.     

Development and validation of a non-aqueous reversed-phase high-performance liquid chromatographic method for the determination of four chemical UV filters in suncare formulations

A non-aqueous reversed-phase high performance liquid chromatographic method (RP-HPLC) with UV detection at 313 nm was developed and validated for simultaneous determination of methylene bis-benzotriazolyl tetramethylphenol (Tinosorb M) along with three other chemical UV filters, octocrylene (Eusolex OCR), octyl methoxycinnamate (Eusolex 2292) and octyl salicylate (Eusolex OS) in suncare products. An isocratic elution was performed on a Hypersil BDS RP-C18 column (250 mm x 4.6 mm), 5 microm particle size, using a mobile phase consisted of methanol-acetonitrile (90:10, v/v) with a flow-rate of 1.5 ml/min. The determination of the four UV filters was not interfered by the excipients in the products. The method of external standard, as well as the standard addition method was used for the determination. The external standard calibration curves were linear for Eusolex OCR, Eusolex 2292, Eusolex OS, and Tinosorb M in the concentration ranges of 0.5-100 microM, 0.5-100 microM, 0.5-200 microM, and 0.2-100 microM, respectively. Day-to-day relative standard deviation of the determination was within 3%. Limits of detection and quantitation of the above compounds were found equal to 36 and 110 nM, 220 and 660 nM, 170 and 520 nM, 44 and 130 nM, respectively. The recovery of these four chemical UV filters from the spiked samples was 96-103%.     

Development of a high-performance liquid chromatographic method with electrochemical detection for the determination of hyperforin

An HPLC method with electrochemical detection for the determination of hyperforin extracts without using additional sample precleaning has been developed and validated. The hyperforin solutions were separated isocratically using a mobile phase consisting of 10% ammonium acetate buffer (0.5 M, pH 3.7)-MeOH-acetonitrile (10:40:50, v/v) at a flow rate of 0.8 mL/min. Hyperforin was detected amperometrically with a glassy carbon electrode at a potential of +1.1 V versus Ag/AgCl/3 M potassium chloride reference electrode. Under these conditions, a plot of integrated peak area versus concentration of hyperforin was found to be linear over the range of 0.054-5.4 microg/mL, with a relative standard deviation of 2.2-8.6%. The limit of detection was 0.050 ng on column. The determination of the hyperforin content in a commercially available St. John's Wort preparation exhibited a mean content of 1.56 mg. Recovery experiments led to a mean recovery rate of 97 +/- 5.8%. The proposed method is not time-consuming, sensitive and reproducible and is therefore suitable for routine analysis of hyperforin in herbal medicinal products.     

A high-performance liquid chromatographic method for the determination of monofluoroacetate

A simple isocratic high-performance liquid chromatographic (HPLC) method for the quantitative analysis of monofluoroacetic acid (MFA), the toxic substance of Dichapetalum cymosum, in plant material, rumen contents (gastric contents), and liver samples is described. A suitable HPLC column that gives optimum sensitivity, accuracy, precision, and separation of MFA is identified. A C-610 organic acid analysis column at ambient temperature with 0.02M H3PO4 as an eluent and ultraviolet detection at 210 nm is utilized to quantitate MFA. Using this method, the average percentage recovery in plant material, bovine liver, and rumen samples is 94.8%, and a detection limit of 12 microg/L is achievable.     

Development and validation of a reliable high-performance liquid chromatographic method for determination of nodakenin in rat plasma and its application to pharmacokinetic study

A simple and reliable high-performance liquid chromatographic (HPLC) method has been developed for the determination of nodakenin in rat plasma. The concentration of nodakenin was determined in plasma samples after deproteinization with methanol using hesperidin as internal standard. HPLC analysis was performed on a Diamonsil C(18) analytical column using acetonitrile-water (25:75, v/v) as the mobile phase and a UV detection at 330 nm. This method was validated in terms of recovery, linearity, accuracy and precision (intra- and inter-day variation). The extraction recoveries were 91.3 ± 10, 87.8 ± 4.8 and 92.6 ± 5.1 at concentrations of 0.500, 5.00 and 40.0 μg/mL, respectively. The standard curve for nodakenin was linear (r(2) ≥ 0.99) over the concentration range 0.250-50.0 μg/mL with a lower limit of quantification of 0.250 μg/mL. The intra- and inter-day precision (relative standard deviation, RSD) values were not higher than 12% and the accuracy (relative error, RE) was within ± 5.8% at three quality control levels. The validated method was successfully applied for the evaluation of the pharmacokinetics of nodakenin in rats after oral administration of Rhizoma et Radix Notopterygii decoction and nodakenin solution.     

Development and validation of a SPE-GC-MS method for the determination of pesticides in surface water

A method for analysis of 20 commonly used pesticides in surface water based on solid-phase extraction and gas chromatography-mass spectrometry was proposed. During method development the key parameters that can affect SPE extraction and determination such as selection of efficient SPE sorbent, pH of water sample, type and volume of elution solvent, breakthrough volume and matrix effects were investigated. The method was validated using spring water spiked with appropriate concentration of pesticides. The obtained correlation coefficients were in range 0.9972–1.000, limits of detection (LOD) were 0.001–0.5?µg?L^?1 and the limits of quantification (LOQ) were 0.005–1?µg?L^?1 depending on a pesticide. Much higher LOD (20?µg?L^?1) and LOQ (50?µg?L^?1) values were obtained for bentazone. The influence of matrix was assessed using real water samples spiked with appropriate concentration of pesticide standards solution. Both signal enhancement and suppression were observed, depending on a pesticide, therefore standard addition method was used for pesticides determination. The developed method was applied on real water samples taken in close vicinity of agricultural fields. Many of the targeted pesticides were found in the samples and the results are presented in this article.     

Development and validation of a thin-layer chromatographic method for determination of chloramphenicol residues on pharmaceutical equipment surfaces

A thin-layer chromatographic (TLC) method with densitometric quantitation using the absorption reflectance mode at 280 nm was developed and validated for the determination of chloramphenicol residues in controlling pharmaceutical equipment cleanliness. Simulated samples at residue levels 0.5, 1, and 1.2 mg/m2 were prepared by spreading the calculated amount of chloramphenicol solution on a 10 dm2 stainless steel surface. After evaporation of the solvent, the residue was removed by 2 methanol-wetted cotton swabs, which were then extracted with methanol. The extract was applied on a high-performance TLC (HPTLC) silica gel F254 plate together with standards ranging from 10 to 60 ng. Plates were developed in a horizontal developing chamber from both sides (36 applications per plate) by using n-hexane-ethyl acetate (35 + 65, v/v) as developing solvent. The mean recovery (n=6) at 1 mg/m2 was 95.8%, and the coefficient of variation was 5.8%. The absolute detection limit was 3 ng, and the quantitation limit 10 ng. The method detection limit was 0.3 mg/m2 by swabbing 2.5 dm2 and 0.075 mg/m2 by swabbing 10 dm2. Chloramphenicol was stable on the plate 2 h before and 24 h after development. Additionally, it was stable during 7 days storage on the cotton swabs in the solvent at room temperature and in diluted standard solution stored in darkness at 4 degrees C. The method can be applied to routine control of pharmaceutical equipment cleanliness by sampling from the stainless steel surface areas of 2.5 to 10 dm2, and an acceptable residue limit of 1 mg/m2.     

Method development and validation of a high-performance liquid chromatographic method for pyrethrum extract.

A robust analytical methodology is developed for the quantitative determination of all six insecticidal components of pyrethrum extract: jasmolin I, cinerin I, pyrethrin I, jasmolin II, cinerin II, and pyrethrin II. This method, based on the separation technique normal-phase high-performance liquid chromatography, offers selectivity, accuracy, precision, linearity, range, ruggedness, and robustness as well as efficiency and ease.     

Validation of a high-performance liquid chromatographic method with fluorescence detection for the simultaneous determination of tetracyclines residues in bovine milk

A high-performance liquid chromatography-fluorescence detection method was optimized and validated to determine tetracyclines residues in bovine milk. Post-column derivatization using metal complexation in non-aqueous reagent increased the fluorescence of chelates by a factor up to 2.54 compared to water (signal-to-noise ratio enhancement). Overall recoveries ranged from 61 to 115%, with RSD_r from 5 to 15% (n = 54). Detection limits ranged from 5 to 35 μg kg⁻¹. Limits of quantification were established at 50 μg kg⁻¹. Decision limits (CCα) were 109, 108 and 124 μg kg⁻¹ and detection capabilities (CCβ) 119, 117 and 161 μg kg⁻¹ for oxytetracycline, tetracycline and chlortetracycline, respectively. The method was applied successfully in a national monitoring program.     

Rapid high-performance liquid chromatographic method for the determination of peroxyacetic acid

The selective oxidation of methyl p-tolyl sulfide (MTS) to the corresponding sulfoxide (MTSO) by peroxyacetic acid and the subsequent rapid separation of the sulfide and sulfoxide are the basis for a fast and reliable HPLC method for the determination of this oxidizing agent in the presence of hydrogen peroxide. The time required for chromatographic separation was reduced to less than 1 min. To improve the long-term stability of the sulfoxide solution, hydrogen peroxide was decomposed catalytically by manganese dioxide. Even in the presence of a tenfold molar excess of hydrogen peroxide, a storability of at least 20 h without a significant increase in MTSO concentration was achieved. External calibration can be performed using the stable and commercially available MTSO. Real samples from a brewery cleaning-in-place disinfection process were analysed and the results were compared with those of the classical two-step titration.