具有高活性(001)晶面的Cr-TiO_2微球的制备及可见光催化性能

采用一步水热法制备了具有高裸露率(001)晶面的锐钛矿相Cr掺杂TiO2(Cr-TiO2)微球,利用场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)和X射线光电子能谱仪(XPS)等对样品进行了表征.结果表明,掺杂的Cr元素以Cr3+离子和CrO3团簇2种形式存在,Cr3+离子进入TiO2晶格,形成Cr3+→Ti4+电荷转移跃迁,Cr-TiO2在可见光区具有强烈吸收.少量的Cr掺杂有利于形成平整的高活性(001)晶面.以可见光降解酸性红染料作为探针反应研究了Cr-TiO2的催化活性.结果表明,具有(001)晶面的Cr-TiO2的催化效率明显优于普通的Cr-TiO2.     

静电纺丝方法制备CaTiO3∶Er3+微米带及其上转换发光性质

CaTiO3:Er3+微米带由静电纺丝方法制备.用X射线衍射、傅里叶变换红外光谱、拉曼光谱、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)和上转换发光表征所制备的样品.SEM和TEM测试证实所得前躯体微米带尺寸均一,烧后得到的微米带是由纳米粒子组成的.在980 nm激光激发下,CaTiO3:Er3样品发出绿光,绿光发射峰位于546 nm,可归属于Er3+离子的4S3/2 →4I15/2跃迁.当Er3+离子的掺杂浓度提高,因为Er3+离子之间的能量传递,红光发射相对于绿光发射增强.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

原位水热合成SrTiO3/TiO2复合纳米纤维及光催化性能

以利用静电纺丝技术制备的TiO2纳米纤维为模板和反应物,原位水热合成了具有异质结构的SrTiO3/TiO2复合纳米纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、能量散射光谱(EDS)、高分辨透射电子显微镜( HRTEM)和X射线光电子能谱(XPS)等测试手段对样品的结构和形貌进行了表征.用罗丹明B(RB)模...     

La3+-SiO2掺杂纳米TiO2的合成及其光催化降解甲基橙的研究

以三嵌段非离子表面活性剂P123为模板,采用水热法合成了La3+-SiO2掺杂纳米TiO2,通过X射线衍射(XRD)、红外光谱(FT-IR)、紫外-可见漫反射吸收光谱(DRS)等手段,考察了La3+-SiO2掺杂纳米TiO2的结构与光学特性.实验结果表明,La3+和SiO2掺杂使TiO2的晶粒在生长过程中受到阻碍.Ti-O-Si键和Ti-O-La键的形成抑制了金红石相的形成和晶粒长大,提高了TiO2的热稳定性,有利于获得高纯度锐钛矿相纳米TiO2.La3+-SiO2掺杂将TiO2的光响应范围拓宽至可见光区,提高了纳米TiO2的光催化性能.与纯纳米TiO2相比,La3+-SiO2掺杂纳米TiO2光催化降解甲基橙的性能显著提高.     

镧系离子掺杂TiO2的制备及其对咪唑降解反应的光催化活性

 以TiCl4和镧系元素的氯化盐溶液为前驱体,采用溶胶-凝胶法制备了不同含量镧系离子掺杂的TiO2光催化剂,用X射线衍射(XRD)、 光致发光光谱(PLS)、 表面光电压谱(SPS)和X射线光电子能谱(XPS)对催化剂进行了表征. XRD结果表明,样品为锐钛矿和金红石的混晶相,镧系离子未进入到TiO2晶格中. PLS和SPS测定结果表明,随着掺杂离子的不同和掺杂含量的不同,样品的谱强度呈现有规律的变化. 在紫外光照射下,以咪唑为目标降解物比较了催化剂的光催化活性. 结果表明,适当含量的镧系离子掺杂可有效促进TiO2表面光生载流子的分离,从而显著提高其光催化活性.     

阳极氧化TiN薄膜制备N掺杂纳米TiO2薄膜及其可见光活性

室温下通过电泳沉积(EPD)的方法在Ti片表面制备TiN薄膜, 然后对TiN薄膜进行阳极氧化得到N掺杂多孔纳米结构的TiO2薄膜. 利用X射线衍射(XRD), X射线光电子能谱(XPS), 扫描电子显微镜(SEM)及光电化学方法对得到的薄膜进行表征. XRD测试结果表明, 经过阳极氧化并在350 ℃空气气氛中退火1 h的薄膜中存在锐钛矿晶型的TiO2. XPS的结果表明, 样品中的N元素取代部分O, 且N的摩尔分数为0.95%. SEM显示, 经阳极氧化后薄膜表面出现多孔纳米结构. 光电化学测试结果显示, 阳极氧化提高了N掺杂TiO2薄膜在可见光下的光电响应. 经阳极氧化并热处理的薄膜在0 V电位及可见光照射下光电流密度为2.325 μA·cm-2, 而单纯热处理的薄膜在相同条件下光电流密度仅为0.475 μA·cm-2. 阳极氧化得到纳米多孔结构提高了N掺杂纳米TiO2薄膜的表面积, 从而对可见光的响应增大.     

模板-电泳沉积法制备TiO2纳米棒

室温(约25℃)下,将钛酸四丁酯水解制得TiO2溶胶,利用电泳沉积法在氧化铝模板中填充胶体,经450℃煅烧处理,制备了TiO2纳米棒.用透射电子显微镜和X射线衍射仪对样品进行了表征.结果表明,所得到的TiO2纳米棒表面光滑、致密,直径约180 nm,具有锐钛矿型结构.     

Co~(2+)/Dy~(3+)掺杂纳米立方Fe_3O_4的热还原制备及磁靶向滞留性能

采用热还原沉淀法制备了一系列Co~(2+)/Dy~(3+)掺杂的纳米立方MxFe3-xO4磁性颗粒.利用X射线衍射仪、透射电子显微镜和振动样品磁强计研究了不同含量掺杂离子对MxFe3-xO4晶体结构、形貌及磁性的影响.研究发现,掺杂未改变母体的对称性,但母体形貌逐渐从立方体向球体过渡;Co~(2+)和Dy~(3+)的掺杂对于铁氧体磁学性质的影响明显不同,当Co~(2+)实际掺杂量为0.44和Dy~(3+)实际掺杂量为0.05时,MxFe3-xO4立方磁性粒子的饱和磁化强度(Ms)达到最大值,分别为76.65和70.21 A·m2·kg-1.与超顺磁性Fe_3O_4球体相比,高磁性掺杂Fe_3O_4立方体在体外模拟磁流体磁靶向定位实验中显示出较高的滞留率.     

N掺杂富含(001)晶面TiO_2纳米片的制备及N掺杂浓度对可见光催化活性的影响(英文)

采用水热法制备了富含(001)晶面的锐钛矿型TiO2纳米片,并通过改变热处理过程中NH3流速制备不同N掺杂浓度的TiO2纳米片.运用X射线衍射、场发射扫描电镜、高分辨率透射电子显微镜、紫外-可见漫反射光谱、X射线光电子能谱和荧光光谱对光催化剂进行了结构和性能表征,并以罗丹明B为目标降解物,考察了N掺杂浓度对TiO2纳米片可见光催化活性的影响.结果表明,NH3流速为40ml/min时制备的N掺杂TiO2纳米片具有最低的光生电子-空穴复合速率,最高的OH产生能力并表现出最高的光催化活性.同时,讨论了N掺杂浓度对TiO纳米片可见光催化活性影响的机理.     

Preparation and Characterization of Room-temperature Ferromagnetic Ni-doped TiO2 Nanobelts

Ni-doped anatase TiO₂ nanobelts (NBs) with different Ni²⁺ contents were simply prepared by combining ion-exchange with hydrothermal treatment. They were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), and magnetic measurement techniques. The results showed that Ni²⁺ cations doped into the TiO₂ lattice and no metallic nickel clusters or nanoparticles could be found. The magnetic results demonstrated that the prepared Ni-doped TiO₂ samples had complex magnetic mechanism including room-temperature ferromagnetic and paramagnetic behaviors, and with the increase of Ni²⁺ content, the magnetization also increased under the same applied field owing to uniform distribution of Ni²⁺ ions in TiO₂ nanobelts.     

Synthesis and Characterization of Magnetic TiO2/SiO2/NiFe2O4 Composite Photocatalysts

Magnetic TiO2/SiO2/NiFe2O4 composite photocatalytic particles with high crystalline TiO2 shell were synthesized via a mild solution route.The prepared composite particles were characterized with X-ray diffraction(XRD),transmission electron microscopy(TEM),high resolution transmission electron microscopy(HRTEM),scanning electron microscopy(SEM),ultraviolet-visible(UV-Vis) spectroscopy and vibrating sample magnetometer(VSM).The results show that the obtained TiO2/SiO2/NiFe2O4 composite particles were composed...     

Interface dominated high photocatalytic properties of electrostatic self-assembled Ag(2)O/TiO(2) heterostructure

Electrostatic self-assembled Ag(2)O/TiO(2) nanobelts heterostructure was synthesized via simple physical mixing of Ag(2)O nanoparticles and TiO(2) nanobelts. The morphologies and microstructures of Ag(2)O/TiO(2) nanobelt heterostructure were characterized by high resolution transmission electron microscopy. The interface dominated high UV photocatalytic activity and degraded photoluminescence strength of composite catalyst confirmed the heterostructure effect between Ag(2)O nanoparticles and TiO(2) nanobelts. X-ray photoelectron spectroscope provided direct evidence of charge transfer on the heterostructures between them.     

WO3/TiO2 复合纤维的制备及储能光催化性能

以钛酸正丁酯为前驱体, 采用静电纺丝技术制得了纯锐钛矿TiO2纤维, 并以其为基质, 通过水热法制备了具有异质结构的WO3/TiO2复合纤维. 利用X射线衍射仪(XRD)、 扫描电子显微镜(SEM)、 能量色散光谱仪(EDS)、 透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等对样品的结构和形貌进行了表征. 以罗丹明B的脱色降解为模型反应, 考察了样品的光催化性能和储能光催化性能. 结果表明, 花状WO3微球包裹在TiO2纤维上, 得到了具有异质结构的WO3/TiO2复合纤维光催化剂. WO3与TiO2复合有利于光生载流子的输运和分离, 增强了体系的量子效率, 提高了光催化活性. WO3/TiO2 复合纤维经光照处理后, 在黑暗条件下显示出储能光催化特性.     

Synthesis and characterization of ultrahigh crystalline TiO2 nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.     

Structures and optical properties of Zn1?x Ni x O nanoparticles by coprecipitation method

Nanocrystals of undoped and nickel-doped zinc oxide (Zn_1?x Ni _x O, where x?=?0.00?C0.05) were synthesized by the coprecipitation method. Crystalline size, morphology, and optical absorption of prepared samples were determined by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), and UV?Cvisible spectrometer. XRD and SEM studies revealed that Ni-doped ZnO crystallized in hexagonal wurtzite structure. Doping of ZnO with Ni²⁺ was intended to enhance the surface defects of ZnO. The incorporation of Ni²⁺ in place of Zn²⁺ provoked an increase in the size of nanocrystals as compared to undoped ZnO. Crystalline size of nanocrystals varied from 10 to 40?nm as the calcination temperature increased. Enhancement in the optical absorption of Ni-doped ZnO indicated that it can be used as an efficient photocatalyst under visible light irradiation. Optical absorption measurements indicated a red shift in the absorption band edge upon Ni doping. The band gap value of prepared undoped and Ni-doped ZnO nanoparticles decreased as annealing temperature was increased up to 800?°C.     

纳米TiO2复合光催化剂的制备及其光解水制氢性能研究

采用溶胶凝胶法分别制备p-MWNTs-TiO2及p-MWNTs/ZnTPP-TiO2复合纳米光催化剂, 并通过热重分析、透射电镜、X射线粉末衍射和紫外-可见漫反射光谱对光催化剂的物理性质进行了表征. 结果表明: 复合光催化剂中碳纳米管热解温度明显提前, TiO2晶化温度延迟, 相变受到抑制, 紫外特征吸收较纯TiO2有明显红移. 对所制备的光催化剂进行光解水产氢性能测试结果表明: 光催化剂的产氢速率维持相对恒定, 有较好的光学稳定性; p-MWNTs和p-MWNTs/ZnTPP对TiO2的掺杂提高了其光催化活性, 光催化剂产氢活性的大小顺序为p-MWNTs/ZnTPP-TiO2＞p-MWNTs-TiO2＞P25＞TiO2.     

SnO2/TiO2复合纳米纤维的制备及光催化性能

采用静电纺丝技术,以聚乙烯吡咯烷酮和钛酸正丁酯为前驱体,制得锐钛矿相TiO2纳米纤维。以TiO2纳米纤维为模板,通过水热合成法,制备了具有异质结构的SnO2/TiO2复合纳米纤维。利用扫描电镜(SEM)、X射线能量色散光谱（EDS）、透射电镜(TEM)和X射线衍射(XRD)等分析测试手段对其形貌和结构进行了表征,结果表明,SnO2纳米粒子均匀地生长在TiO2纳米纤维表面,形成了异质结构的SnO2/TiO2复合纳米纤维材料。通过改变反应物浓度,能有效地实现SnO2/TiO2复合纳米纤维的可控合成。以罗丹明B为模拟污染物,考察了SnO2/TiO2复合纳米纤维的光催化性能,与纯TiO2纳米纤维相比光催化活性明显提高,初步探讨了光催化反应机理。     

过渡金属掺杂和碳纳米管（CNT）接枝双重改性TiO2光催化剂

提出了一种过渡金属掺杂和碳纳米管(CNT)双重改性TiO2的新方法:首先采用溶胶-凝胶法合成掺杂镍和铁的二氧化钛基催化剂,然后采用流化床化学气相沉积方法(FBCVD)在二氧化钛基催化剂表面接枝生长CNT,得到CNT/Fe-Ni/TiO2复合光催化剂.通过X射线衍射、扫描电子显微镜、比表面分析、拉曼光谱、紫外-可见吸收光谱、荧光光谱等方法考察了双重改性复合光催化剂CNT/Fe-Ni/TiO2的结构和性能,通过降解亚甲基蓝溶液评价了双重改性复合光催化剂的活性.结果表明,在TiO2表面接枝的CNT具有较好的石墨化结构,CNT生长过程中小部分TiO2由锐钛矿向金红石晶型转变.过渡金属和CNT双重改性有效地克服了TiO2的比表面积小、量子效率低等缺点,明显提高了TiO2的光催化活性.     

Morphology-controllable synthesis and characterization of single-crystal molybdenum trioxide

Molybdenum trioxide nanobelts and prism-like particles with good crystallinity and high surface areas have been prepared by a facile hydrothermal method, and the morphology could be controlled by using different inorganic salts, such as KNO3, Ca(NO3)2 , La(NO3)3, etc. The possible growth mechanism of molybdenum trioxide prism-like particles is discussed on the basis of the presence of H+ and the modification of metal cations. The as-prepared nanomaterials are characterized by means of powder X-ray diffraction (PXRD), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), Fourier transformation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and ultraviolet and visible spectroscopy (UV-vis). TEM and HRTEM micrographs show that the molybdenum trioxide nanobelts and prism-like particles have a relatively high degree of crystallinity and uniformity. BET specific surface areas of the as-prepared molybdenum trioxide nanocrystals are 67-79 m2 g-1. XPS analysis indicates that the hexavalent molybdenum is predominant in the nanocrystals. UV-vis spectra reveal that the direct band gap energy of the annealed molybdenum trioxide prism-like particles shows a pronounced blue shift compared to that of bulk MoO3 powder. Interestingly, molybdenum trioxide nanobelts exhibit a red shift under this condition.