海底地层回波数据的波场外推法成像处理

海底地层回波数据的成像处理是依据地层剖面仪在海面激发以及水听器接收到的海底地层声纳回波信息来研究海底地层沉积结构的一种方法。文中运用描述声波场传播规律的波动方程将海面观测回波场记录进行反向外推处理,并指出在均匀介质或水平层状介质情况下时间成像方法的合理性,以及在沉积层构造复杂时,应同时进行绕射波场的收敛和由于介质速度横向变化引起的折射效应的时移校正的深度成像处理,从而获取准确的海底地层的结构形态。     

海底任意倾斜层的声速测量(T~2-X~2法的分析)

海底地层声速的测量系统由地层剖面仪加一条拖曳水听器阵组成。在地层界面为任意倾斜的情况下,按照T~2-X~2法的原理对共深度点的回波数据进行计算是测量地层声速的基本方法。根据地层声速和阵移速度之间关系的一般表达式,结合对各界面的正射线的几何分析,导出了计算海底下各层声速的方程式,并且讨论了用简便的迭代法求解这些方程式的有关问题。用T~2-X~2法测量声速的误差主要来源于:回波时距曲线偏离理想的双曲线,水听器阵拖曳速度不稳定和回波到达时间的随机漂移。通过分析,得到了相应的误差估计公式。由此,也为正确决定测量系统的设计参数提供了依据。     

南海北部负跃层环境下海底参数声学反演

利用2015年南海北部声学实验的实验数据,对海底声学参数进行反演。在综合分析声速起伏及海底模型对海底反演影响的基础上,通过选择等效的海水声速剖面和海底模型,改进了多参量联合地声反演方法,使得其不仅能解决反演中的多值性问题,还能适用于负跃层起伏环境下的声学反演。即当用匹配场反演海底声速和用传播损失反演海底衰减时,如果温跃层内有内波等随机起伏,可使用传播路径上平均声速剖面和单层等效海底进行声场计算。反演得到的海底声速和密度结果与海底采样测量符合较好,拟合给出了海底衰减系数随频率的非线性经验关系式。反演结果可为南海北部声传播规律研究与应用提供海底参数。     

海底薄地层和硬地层声速测量方法的研究(射线参数法和折射法分析)

应用T²-X²法测量海底薄地层和硬地层的声速常常不能得到满意的结果。为此,有必要在一个由声源和拖曳水听器阵组成的声速测量系统中设置接射线参数法和折射法测量海底地层声速的处理功能。本文从这两种方法的测量原理出发,着重研究了地层回波时距数据的处理方法,以及由各种因素(如回波时间随机抖动和地层界面倾斜角不确定性等)所引起的声速测量误差等问题。射线参数法和折射法测量声速的数据处理和运算过程已经用TURBO-PASCAL语言编程,并通过对典型实例的模拟计算作了验证。     

一种基于模态匹配的浅海波导中宽带脉冲声源的被动测距方法

针对浅海波导中宽带脉冲声源的被动测距问题,本文在模态匹配和匹配场处理定位方法的基础上,提出了一种适用于具有液态半无限空间海底的浅海波导中声源的单水听器被动测距方法.利用warping变换可以对脉冲声源接收信号的各阶简正波实现有效分离,由此得到各阶简正波的频域信号.海底相移参数是描述海底地声参数的一个重要参量,包含了海底地声参数信息,而各阶简正波的水平波数可以通过含有海底相移参数的表达式来表达.此外,由于声速剖面对简正波的各阶水平波数具有相近的影响,因此通过对任意两阶简正波进行联合处理,可以近似消除声速剖面对简正波水平波数差的影响.任意两阶简正波的水平波数差只近似用于海底相移参数、海深以及波导中平均声速三个参数有关,可以简单、快速地计算相应拷贝场,然后通过建立代价函数并对简正波模态进行匹配,可以实现对水下脉冲声源的被动测距.与传统的模态匹配定位方法相比,本文提出的方法既不需要使用水听器阵,又可以简单、快速地计算出拷贝场.数值仿真和海上实验数据处理结果的测距误差都在10%以内,证明了该方法的有效性.     

直剪颗粒体系声波探测

建立了声波监测系统,探测颗粒体系在直剪过程中声速与剪切应力的变化关系.发现声速在剪切开始后随着剪切应力的增加会迅速减小.而在应力达到屈服点之后,声速变化逐渐变缓并趋近于一个稳定值.剪切作用对声速变化的影响小于20%,而非所预测由于剪切带的形成,声波(尤其是横向波)的振动无法通过剪切带而使得探测的飞行速度变为零.这是由于直剪的应变率甚低于声波的频率,直剪的颗粒体系可被视为局部区域膨胀的准静态的弹塑固体.结合等效介质理论和颗粒弹性理论对以上结果进行了解释和讨论.     

利用井孔偶极弯曲波反演横向各向同性孔隙地层渗透率的研究

对利用井孔偶极弯曲波衰减特性反演横向各向同性孔隙地层的纵、横向渗透率进行了理论方法和数值研究.对软地层,在方差函数极值行为分析的基础上,用最小二乘反演对多组理论模拟数据进行处理,得到的纵、横向渗透率精度都比较高,这与软地层弯曲波衰减对纵向渗透率的敏感程度明显比硬地层高有关;用添加不同强度的随机噪声综合反映现场资料可能带来的误差,对多道间提取的衰减叠加求平均可明显的抵消噪声的影响;对快速孔隙地层偶极声测井理论模拟数据也尝试性地进行了纵、横向渗透率反演,发现,虽然硬地层弯曲波的衰减对纵向渗透率很不敏感,但纵向渗透率的取值偏离真值却对横向渗透率的反演结果有明显影响.     

海底沉积物压缩波声速比与物理特性的关系

海底沉积物因组成结构复杂导致声学特性复杂多样,多种理论解释模型存在参数较多且各具适用性现象·通过运用体积平均和等效参数的方法对海底沉积物声波传播机理进行研究,提出一种少参数的海底沉积物与底层海水的压缩波声速比通用模型(General Model of Sound Speed Ratio,GMSSR).GMSSR模型包含弹性结构分布因子、孔隙度、等效密度比、等效弹性模量比4个物理特性参数。分析海底沉积物两相介质结构的串联和并联两种极限情况分析,基于弹性结构分布因子和串并联结构的体积平均分布建立一般情况下海底沉积物的等效弹性模量表达式·应用GMSSR合理地分析各海域测量的海底沉积物声速比经验模型的共性和解释南海实测数据分散的范围,表明:(1)表层海底沉积物主要是以串联结构为主,接近于悬浮液状态或者体积分量很少的并联堆积状态;(2)等效弹性模量比的影响因素大于等效密度比,结构变化往往通过影响弹性结构分布因子而影响等效弹性模量比,从而引起声速比的变化;(3)不同研究海域的声速比-孔隙度经验关系具有相似性,可以通过GMSSR模型分析得出;(4)基于弹性结构分布因子的差异,可以合理解释南海海域测量表层海底沉积物声速比较大的分散性。     

声速剖面对不同深度声源定位的影响

在对一次试验数据进行匹配场定位处理时发现, 选取声速剖面有轻微失配的情形下, 水面弱声源显现, 水下强声源反而消失. 基于该现象研究了声速剖面失配对不同深度声源定位的影响. 首先通过仿真试验排除海上试验中不确定因素的影响, 进一步得出深处声源定位受声速剖面失配影响较大的结论, 并针对夏季负跃层情形进行跃层深度失配的仿真, 初步得出在跃层下边界以下10 m附近处的声源对声速剖面失配最敏感. 最后从简正波的角度进行理论分析, 分两点对这一现象进行了合理解释.     

倾斜地层下的井孔声场分析及声速校正图版制作

理解声波在倾斜井孔下的传播规律,对于准确获得目的层真速度有着至关重要的作用。通过有限差分和几何声学分析方法对比了倾斜地层下纵横波首波速度的变化规律,旨在建立倾斜地层下的声速校正图版。研究结果表明,当倾斜地层速度"上低下高"时,从全波中得到的声波速度不再是地层的真实速度,均大于目的层真速度。尤其是当地层界面倾角大于45°时,即便是源距超过了4 m,仍对首波速度有影响,必须对其校正。相反,当倾斜地层速度"上高下低"时,任何源距和地层倾角下的视速度值都接近目的层真速度,可以不予校正。根据以上分析,建立了倾斜地层下的声速校正图版,并指出下层速度的变化对于校正图版有着较大影响,源距的变化对于图版影响很小,在不同源距下可以使用同一个图版。     

Imaging of echo data of submarine sedimentary beds layer-by-layer with acoustic wave equation refraction correction method

I.IntroductionThcobjcctofsubmarincstratasurvcyisforgco1ogicalintcrprctation,inwhichsubmarinccchodataarcuscd.Rightgcologicalintcrprctationisbascdonthedatawithhighsignal-to-noiseratio(S/N)andhighrcsoIution.ThcusualmcthodofimprovingS/Nistocollcctwide-anglcechodatahyasystcmcomposcdofanacousticsourceandahydrophoncsfrcamcrtOwedbchindaprofilerandstackthcdataincommon-dcpth-point(CDP)gathcr,whichcansupprcsssomctypcsofintcrfcrcnce.a..s[1'2].Bcsidcs,combincdmcthodsoffic1dco11cctionandfi1teringmcthods…     

Wavefield-extrapolation imaging for echo data of sea-bed sediment layers

I.IntroductionImagingechodataofseabedsedimentlayersisoneofimportantpartsingeoacousticalstudies.Theechodatareflectedfromtheillterfacesofsea-bedlayersarereceivedatseasurfacebyahydrophonestreamerwithaseismicprofiler.Throughimageprocessing,theacctiratestructureofseabedsedimentlayerscanbereconstructedeffectively['l'].Thusthismethodisoftenregardedasatoolfortargetdetection.Anexampleofcommon-shot-pointrecordstoexplainthesignificanceofthemethodisshownasfollows:InFig.1(a),Risalayerbetweentwohomogeneou…     

Theory and signal processing of acoustic correlation techniques for current velocity measurement

A theoretical model and signal processing of acoustic correlation measurements to estimate current velocity are discussed. The sonar space-time correlation function of volume reverberations within Fraunhofer zone is derived. The function, which is in exponential forms, is the theoretical model of acoustic correlation measurements. The characteristics of the correlation values around the maximum of the amplitude of the correlation function, where most information about current velocity is contained, are primarily analyzed. Localized Least Mean Squares （LLMS） criterion is put forward for velocity estimation. Sequential Quadratic Programming （SQP） method is adopted as the optimization method. So the systematic signal processing method of acoustic correlation techniques for current velocity measurement is established. A prototype acoustic correlation current profiler （ACCP） underwent several sea trials, the results show that theoretical model approximately coincides with experimental re- sults. Current profiles including the speed and direction from ACCP are compared with those from acoustic Doppler current profiler （ADCP）. The current profiles by both instruments agree reasonably well. Also, the standard deviation of velocity measurement by ACCP is statistically calculated and it is a little larger than predicted value.     

声相关流体速度测量理论和信号处理方法

研究了测量流体速度的声相关测速理论和信号处理方法。获得了在声呐阵夫琅和费区域内适用的声呐阵时空相关函数,它是指数函数,这是相关测流速的理论模型。重点研究了时空声相关函数最大值附近的特性,它包含流速的主要信息。提出了局域最小二乘估计作为速度估计准则,采用序列二次规划作为最优化的方法,由此建立了声相关流速测量的信号处理方法。进行多次海上系统试验,验证了理论模型;给出了声相关海流剖面仪测得的流速、流向和流速剖面,与声多普勒海流剖面仪进行了对比,结果符合;最后给出了声相关海流剖面仪的测速均方差,稍大于理论值。     

Dynamic behavior and sound transmission analysis of a fluid-structure coupled system using the direct-BEM/FEM

A direct-BEM/Fem method was proposed to analyze the vibration and acoustic radiation characteristics of a submerged structure. Model parameters of the structure and the fluid-structure interaction due to surrounding water were analyzed by using FEM and direct BEM. Vibration velocity of the outer hull surface and underwater sound pressure were computed through modal superposition technique. The direct-BEM/FEM method was first validated by analyzing a submerged cylindrical shell, then was used to analyze the vibro-acoustic behavior of a submarine stern structure. The results have demonstrated the direct-BEM/FEM method is more effective than FEM in computing the underwater sound radiation of the stern structure.     

在浅海环境中潜艇隐蔽占位航路研究

本文运用平滑平均场理论和动态规划方法，研究潜艇如何利用水声环境蔽占位，重点分析了在水声环境比较好和比较差的两种典型情况下，潜艇用定速和每航段用最低速度占位问题，结果表明在不同的水声环境和相互态势下，潜艇须采用不同的隐蔽航路占位。     

Effect of diffusion layers and defect layer on acoustic phonons transport through the structure consisting of different films

By using the continuum elastic approximation model and the transfer matrix method, we investigate the effect of diffusion layers and defect layer on acoustic phonons transport through the structure consisting of different films. Our work show that most acoustic phonons can easily pass the structure, but some only have much less transmission probabilities and form corresponding dips in the transmission spectrum. With the change of the structure parameters such as the width of diffusion layers and defect layer, the number of unit cell and the density of containing Al in diffusion layers and defect layer, the magnitude of the frequencies of acoustic phonons corresponding to the dips almost remain unchanged, but the transmission coefficients corresponding to the dips change at different degree, and the transmission probabilities of some frequencies are very sensitive to the variation of the above-mentioned structure parameters. These results can provide some references in controlling the transmission coefficients of acoustic phonons, devising parts of acoustic apparatus and theoretical investigation related.     

Properties of photocured epoxy resin materials for application in piezoelectric ultrasonic transducer matching layers

This paper describes the acoustic properties of a range of epoxy resins prepared by photocuring that are suitable for application in piezoelectric ultrasonic transducer matching layers. Materials, based on blends of diglycidyl ether of Bisphenol A and 1,4-cyclohexanedimethanol diglycidyl ether, are described. Furthermore, in order to vary the elastic character of the base resin, samples containing polymer microspheres or barium sulfate particles are also described. The acoustic properties of the materials are determined by a liquid coupled through transmission methodology, capable of determining the velocity and attenuation of longitudinal and shear waves propagating in an isotropic layer. Measured acoustic properties are reported which demonstrate materials with specific acoustic impedance varying in the range 0.88-6.25 MRayls. In the samples comprising blends of resin types, a linear variation in the acoustic velocities and density was observed. In the barium sulfate filled samples, acoustic impedance showed an approximately linear variation with composition, reflecting the dominance of the density variation. While such variations can be predicted by simple mixing laws, relaxation and scattering effects influence the attenuation in both the blended and filled resins. These phenomena are discussed with reference to dynamic mechanical thermal analysis and differential scanning calorimetry of the samples.