Demonstration of a surface plasmon-coupled emission (SPCE)-based immunoassay in the absence of a spacer layer

The technique of surface plasmon-coupled emission (SPCE) involves the coupling of light which is emitted from a fluorophore into the surface plasmon of an adjacent thin metal film, giving rise to highly directional emission. We have combined the advantages of SPCE with the high light collection efficiency of supercritical angle fluorescence by carrying out an immunoassay on a paraboloid array biochip in the absence of the conventional SPCE spacer layer normally used to minimize metal quenching of the fluorescence. In this work, we have successfully demonstrated an SPCE-based assay by utilizing the protein assay layer as the spacer layer. A novel 3 × 3 injection molded polymer biochip with paraboloid elements was used. The paraboloid elements served to enhance the light collection efficiency while the top surface was coated with a gold layer to use excitation of surface plasmons and detection of SPCE emission. Theoretical modeling of the gold-protein layer structure showed that the surface plasmon resonance angles were located in the detection range of the paraboloid biochip. The polarization dependence of SPCE emission was also demonstrated. Finally, a human IgG sandwich immunoassay was carried out which exhibited a limit of detection of ~10 ng/ml using 3σ. The results demonstrate the potential of the SPCE-based paraboloid array biochip as a novel platform for high-throughput analysis of biomolecular interactions.     

Surface characterization and efficiency of a matrix-free and flat carboxylated gold sensor chip for surface plasmon resonance (SPR)

We report the preparation and characterization of a matrix-free carboxylated surface plasmon resonance (SPR) sensor chip with high sensing efficiency by functionalizing a bare gold thin film with a self-assembled monolayer of 16-mercaptohexadecanoic acid (SAM–MHDA chip). The self assembled monolayer surface coverage of the gold layer was carefully evaluated and the SAM was characterized by infrared reflection absorption spectroscopy, X-ray photoemission spectroscopy, atomic force microscopy, X-ray reflectivity-diffraction, and SPR experiments with bovine serum albumin. We compared the SPR signal obtained on this chip made of a dense monolayer of carboxylic acid groups with commercially available carboxylated sensor chips built on the same gold substrate, a matrix-free C1 chip, and a CM5 chip with a ~100 nm dextran hydrogel matrix (GE Healthcare). Two well-studied interaction types were tested, the binding of a biotinylated antibody (immunoglobulin G) to streptavidin and an antigen–antibody interaction. For both interactions, the well characterized densely functionalized SAM–MHDA chip gave a high signal-to-noise ratio and showed a gain in the availability of immobilized ligands for their partners injected in buffer flow. It thus compared favourably with commercially available sensor chips.     

Enhanced modulation of magnetic field on surface plasmon coupled emission (SPCE) by magnetic nanoparticles

This article demonstrates the enhancement of magnetic nanoparticles on magnetic field modulation of surface plasmon coupled emission (SPCE), and this method is designed as a biosensor to prove the feasibility of magnetic field modulated SPCE to be employed in the field of biosensing and biodetection.     

Enhanced modulation of magnetic field on surface plasmon coupled emission (SPCE) by magnetic nanoparticles

The obvious enhancement effect of magnetic nanoparticles (MNPs) introduced in Cr/Co/Cr/Au substrate on the pulsed magnetic field-modulated surface plasmon coupled emission (SPCE) was investigated, and the observed enhancement factor was 4 comparing with the magnetic field modulated SPCE without MNPs. This is the new observation for the magnetic field modulated SPCE, and this method was designed as a biosensor, which to our knowledge, is the first application of magnetic field-modulated SPCE in biosensing and detection field. This strategy is a universal approach to increase the fluorescence signal and helps to build the new SPCE based stimulus-response system.     

Combination of cysteine- and oligomerization domain-mediated protein immobilization on a surface plasmon resonance (SPR) gold chip surface

Here we report an effective method for protein immobilization on a surface plasmon resonance (SPR) gold chip, describing the combination of cysteine- and oligomerization domain-mediated immobilization of enhanced green fluorescent protein (EGFP) as a model protein for the purpose of orientation-controlled surface density packing. In order to facilitate the oligomerization of EGFP, the dimeric and trimeric constructs derived from GCN4- leucine zipper domain were chosen for multimeric EGFP assembly. For orientation-controlled immobilization of the protein, EGFP modified with cysteine residues showing excellent orientation on a gold chip was used as a starting protein, as previously reported in our earlier study (Anal. Chem., 2007, 79, 2680-2687). Constructs of EGFP with oligomerization domains were genetically engineered, and corresponding fusion proteins were purified, applied to a gold chip, and then analyzed under SPR. The immobilized EGFP density on a gold chip increased according to the states of protein oligomerization, as dimeric and trimeric EGFPs displayed better adsorption capability than monomeric and dimeric forms, respectively. Fluorescence measurement corroborated the SPR results. Taken together, our findings indicated that the combination of cysteine- and oligomerization domain-mediated immobilization of protein could be used in SPR biosensor applications, allowing for an excellent orientation and high surface density simultaneously.     

Local surface patterning by chitosan-stabilized gold nanoparticles using the direct mode of scanning electrochemical microscopy (SECM)

An approach for patterning surfaces with prepared nanoparticles is described. Chitosan-stabilized gold nanoparticles (Au/chitosan NPs) were locally deposited on stainless steel (StSt), indium tin oxide (ITO), and highly-ordered pyrolytic graphite (HOPG). Deposition was driven by local pH gradient formed between a surface and a scanning electrochemical microscopy tip set in the direct mode. The pH at the substrate was increased upon biasing the surface by negative potentials, which caused the reduction of water. As the pH on the surface exceeded that of $ {\mathrm{pK}}_{{\mathrm{chitosanH}}^{+}}\sim 6.3 $ deprotonation of the amino groups of chitosan caused the irreversible deposition of the chitosan/AuNPs. The effect of different parameters, such as tip–surface distance and time, on deposition was studied. While the potential duration showed no clear influence, smaller tip–substrate distance and more negative potentials applied to the surface caused larger deposits. The overpotential needed for the deposition of nanoparticles on HOPG was the highest while that for StSt was the lowest. On the former, the sluggish kinetics caused the deposition of ring-shaped structures while disk-shaped deposits were formed on the other surfaces.     

Immobilizing shortened single-walled carbon nanotubes (SWNTs) on gold using a surface condensation method

We propose a surface condensation method for assembling single-walled carbon nanotubes (SWNTs) on gold. The as-prepared long and randomly tangled SWNTs were cut into short pipes by chemical oxidation, allowing the nanotubes to be terminated by carboxyl functionalities. A surface condensation reaction was then performed by immersing an amino self-assembled monolayer (SAM)-modified gold substrate into the dimethylformamide suspension of carboxylic nanotubes with the aid of dicyclohexylcarbodiimide condensation agent. Raman spectroscopy and atomic force microscopy (AFM) results show that a highly aligned assembly of SWNTs has been formed on gold, with the nanotubes standing on the surface stable enough for a long ultrasonication. In combination with the microcontact printing (muCP) technique, we have fabricated patterned nanotube assemblies using this surface condensation method. Moreover, we found that the "giant" carbon nanotubes tend to form bundles on an amino-terminating surface, likely following a nucleation-growth model.     

Fluorescence ratiometry and fluorescence lifetime imaging: using a single molecular sensor for dual mode imaging of cellular viscosity

Intracellular viscosity strongly influences transportation of mass and signal, interactions between the biomacromolecules, and diffusion of reactive metabolites in live cells. Fluorescent molecular rotors are recently developed reagents used to determine the viscosity in solutions or biological fluid. Due to the complexity of live cells, it is important to carry out the viscosity determinations in multimode for high reliability and accuracy. The first molecular rotor (RY3) capable of dual mode fluorescence imaging (ratiometry imaging and fluorescence lifetime imaging) of intracellular viscosity is reported. RY3 is a pentamethine cyanine dye substituted at the central (meso-) position with an aldehyde group (CHO). In nonviscous media, rotation of the CHO group gives rise to internal conversion by a nonradiative process. The restraining of rotation in viscous or low-temperature media results in strong fluorescence (6-fold increase) and lengthens the fluorescence lifetime (from 200 to 1450 ps). The specially designed molecular sensor has two absorption maxima (λ(abs) 400 and 613 nm in ethanol) and two emission maxima (in blue, λ(em) 456 nm and red, 650 nm in ethanol). However it is only the red emission which is markedly sensitive to viscosity or temperature changes, providing a ratiometric response (12-fold) as well as a large pseudo-Stokes shift (250 nm). A mechanism is proposed, based on quantum chemical calculations and (1)H NMR spectra at low-temperature. Inside cells the viscosity changes, showing some regional differences, can be clearly observed by both ratiometry imaging and fluorescence lifetime imaging (FLIM). Although living cells are complex the correlation observed between the two imaging procedures offers the possibility of previously unavailable reliability and accuracy when determining intracellular viscosity.     

Determination of chromium(III) and total chromium using dual channels on glass chip with chemiluminescence detection

A simple, rapid and sensitive method for the determination of chromium(III) and total chromium using the simple dual T channels on glass chip with negative pressure pumping system and chemiluminescence (CL) detection is presented. The CL reaction was based on luminol oxidation by hydrogen peroxide in basic aqueous solution catalyzed by chromium(III). Total chromium in form of chromium(III) was achieved after chromium(VI) was completely reduced by acidic sodium hydrogen sulfite. Total chromium could then be determined with the same strategy as the chromium(III). The CL reagent was composed of 1.0 × 10⁻⁴ mol/L luminol, 1.0 × 10⁻² mol/L hydrogen peroxide and 0.10 mol/L sodium bromide in 0.050 mol/L carbonate buffer (pH 11.00). The 1.0 × 10⁻² mol/L ethylenediaminetetraacetic acid was added into the sample solution in order to improve the selectivity. Chromium(III) could be detected at a notably concentration of 1.6 × 10⁻¹⁶ mol/L and a linear calibration curve was obtained from 1.0 × 10⁻¹⁵ to 1.0 × 10⁻¹³ mol/L. The sample and CL reagent consumption were only 15 and 20 μL, respectively. The analysis time was less than 1 min per sample with the precision (%R.S.D.) was 4.7%. The proposed method has been applied successfully to the analysis of river water, mineral waters, drinking waters and tap water. Its performance was verified by the analysis of certified total chromium-reference materials and by recovery measurement on spiked synthetic seawater sample.     

Direct optical emission spectroscopy of liquid analytes using an electrolyte as a cathode discharge source (ELCAD) integrated on a micro-fluidic chip

Atomic emission detection of metallic species in aqueous solutions has been performed using a miniaturised plasma created within a planar, glass micro-fluidic chip. Detection was achieved using an Electrolyte as a Cathode Discharge source (ELCAD) in which the sample solution itself is used as the cathode for the discharge. To realise the ELCAD technique within a micro-fluidic device, a parallel liquid-gas flow was set up in a micro-channel and a glow discharge ignited between the flowing liquid sample surface and a metal wire anode. The detection of copper and sodium was achieved, using atmospheric pressure air as a carrier gas, by observation of atomic emission lines of copper at 324 nm, 327 nm, 511 nm, 515 nm and 522 nm and an atomic emission line of sodium at 589 nm using a commercially available miniaturised spectrometer. A total electrical power of less than 70 mW was required to sustain the discharge. A semi-quantitative, absolute detection limit of 17 nmol s(-1) was obtained for sodium with a sample flow rate of 100 microL min(-1) and an integration time of 100 ms in air at atmospheric pressure. The volume required for such detection is approximately 170 nL. Further analysis was performed with an Echelle spectrometer using both argon and air as a carrier gas. The geometry and flow rates used demonstrate the feasibility of integrating such micro-plasmas into other micro-fluidic devices, such as miniaturised CE devices, as a method of detection. The potential for using such micro-plasmas within highly portable miniaturised systems and mu-TAS devices is presented and discussed.     

Monitoring of the self-assembled monolayer of 1-hexadecanethiol on a gold surface at nanomolar concentration using a piezo-excited millimeter-sized cantilever sensor

In this paper, we describe a new method of measuring alkanethiol monolayer formation on a gold surface. A gold-coated millimeter-sized rectangular-shaped lead zirconate titanate (PZT) cantilever of dimensions 3.5 x 2 x 0.05 mm, previously shown to detect a picogram level of mass change, was used to measure the adsorption kinetics of 1-hexadecanethiol in ethanol over six orders of concentration range (1 nM to 10 mM) in real time. The flexural mode of cantilever vibration, 45.5 +/- 0.01 kHz, was monitored during the self-assembly. The total resonant frequency change obtained for the 1 nM, 10 nM, 100 nM, 1 microM, 4 mM, 8 mM, and 10 mM thiol concentrations were 116 +/- 2 (n = 2), 225 (n = 1), 270 +/- 10 (n = 2), 440 +/- 10 (n = 2), 900 +/- 10 (n = 2), 900 +/- 10 (n = 2), and 900 +/- 10 (n = 2) Hz, respectively. These results compare favorably to literature results in that the rate of the monolayer formation is concentration-dependent and the exponential change during adsorption follows the reversible first-order Langmuir kinetic model. The rate constants of adsorption and desorption were 0.061 M(-1) s(-1) and 3.61 x 10(-4) s(-1), respectively. The significance of the results is that millimeter-sized PZT cantilevers can be used in real-time for characterizing self-assembly of monolayer formation at nanomolar concentration levels. In addition, at 1 nM, the adsorption was found not to be diffusion limited.     

Fabrication of a sensor chip containing Au and Ag electrodes and its application for sensitive Hg(II) determination using chronocoulometry

In this work, we explored a novel fabrication method to construct Au and Ag electrodes on chip, utilizing the different solubility of gold and silver in different etching solutions. KI-I₂ etching solution and 50% HNO₃ were chosen to dissolve the metal layers alternatively. Planar electrodes with gold and silver could be simultaneously and accurately patterned on chip using photolithographic technique. The as-prepared electrode could be directly served as integrated three-electrode system for electrochemical measurement. Based on it, a sensing strategy has been carried out using home-made electrochemical sensing (ECS) chip, which depended on the competition of double strand DNA and Hg(II)-mediated T–T base pairs (T-Hg(II)-T). Actually, a mercury specific oligonucleotide (MSO) was immobilized onto the thus-fabricated gold working electrode and employed as the sensing element. Chronocoulometry (CC) was chosen to monitor the differences of surface charge volume and quantify the concentrations of Hg(II) ions with a low detection limit down to 1 nM. Therefore, a facile method to fabricate Au and Ag electrodes has been demonstrated to simplify the production of ECS chip. The ECS chip was finally used for constructing an effective sensing platform for sensitive Hg(II) determination, which held promising potential for designing ECS chip in lab-on-a-chip device or point-of-care diagnosis.     

Voltammetric paracetamol sensor using a gold electrode made from a digital versatile disc chip and modified with a hybrid material consisting of carbon nanotubes and copper nanoparticles

A composite consisting of carbon nanotubes (CNT) and copper nanoparticles (CuNPs) was prepared by a chemical reduction method, and its structure characterized by scanning electron microscopy, transmission electron microscopy energy dispersive spectroscopy and FT-IR spectrometry. The hybrid composite was deposited on the surface of a disposable gold electrode that was manufactured from a commercial digital versatile gold disc by a drop casting method. The electrochemical properties of the modified electrode were investigated by cyclic voltammetry and differential pulse voltammetry. The sensor showed an excellent electrocatalytic activity towards oxidation of paracetamol (PA). The calibration plot (with current typically measured at 0.41 V vs. Ag/AgCl) is linear in the 0.5 to 80 μM concentration range, and the detection limit is as low as 10 nM. The sensor was successfully applied to the determination of PA in spiked water and tablet samples where it gave recoveries ranging between 95.25 and 100.5 %.

Open image in new window

Graphical abstract Carbon nanotubes (CNT) -copper nanoparticles (CuNPs) hybrid composite was synthesized by a facile method then the nanohybrid was used as a modifier for the DVD gold electrode for improving its performance toward paracetamol electrooxidation. Cyclic voltammetry and differential pulse voltammetry were used for characterization and determination of paracetamol, respectively.

     

Rapid fabrication of electrochemical enzyme sensor chip using polydimethylsiloxane microfluidic channel

Applicability of polydimethylsiloxane (PDMS) for easy and rapid fabrication of enzyme sensor chips, based on electrochemical detection, is examined. The sensor chip consists of PDMS substrate with a microfluidic channel fabricated in it, and a glass substrate with enzyme-modified microelectrodes. The two substrates are clamped together between plastic plates. The sensor chip has shown no leakage around the microelectrodes under continuous solution flow (34 μl/min). Amperometric response of the sensor chips developed in this work suggest that various types of enzyme sensors can be designed by using PDMS microfluidic channels.     

Olefination of ketones using a gold(III)-catalyzed Meyer-Schuster rearrangement

An atom-economical and efficient olefination strategy for ketones is described. Ethoxyacetylide addition followed by a gold-catalyzed Meyer-Schuster rearrangement affords alpha,beta-unsaturated esters, generally in excellent overall yield from the starting ketones. The alkynophilicity of Au3+ promotes an interaction with the electron-rich acetylenes that catalyzes the Meyer-Schuster rearrangement selectively over other conceivable pathways.     

Detection of non-cross-linking interaction between DNA-modified gold nanoparticles and a DNA-modified flat gold surface using surface plasmon resonance imaging on a microchip

Gold nanoparticles (GNPs) with fully matched DNA duplexes on their surfaces aggregate together without molecular cross-linking at high salt concentrations. The mechanism of this non-cross-linking (NCL) interaction has been elusive. In this paper, NCL interaction between duplex-modified GNPs and a duplex-modified flat gold surface is presented for the first time. This new experimental platform has enabled us to study the NCL interaction between duplexes with different sequences. We immobilized 15-base single-stranded (ss) DNA onto the surfaces of GNPs with a diameter of 40nm and onto a flat gold substrate. The GNPs were hybridized with 15-base ssDNA at a low salt concentration. A microfluidic device was used for simultaneous delivery of the following three components onto the gold substrate: the duplex-modified GNPs, 15-base ssDNA to be hybridized onto the substrate, and NaCl at a high concentration. Adsorption of the GNPs onto the substrate was monitored using surface plasmon resonance imaging. When the GNPs and the substrate had an identical sequence, the adsorption behavior was analogous to the aggregation behavior of GNPs in test tubes. Furthermore, we investigated 12 cases in which the GNPs and the substrate had completely different sequences, and obtained results suggesting that the NCL attraction force primarily depends on the terminal base pairs of the duplexes. This means that the main mechanism of the NCL interaction is likely to be inter-duplex base stacking rather than formation of Holliday junctions.     

Photocured thiol-ene based optical fluorescence sensor for determination of gold(III)

This study describes the preparation and the characterization of a new thiol-ene based polymeric fluorescence sensor by photo initiated polymerization of trimethylolpropane tris(3-mercaptopropionate), 2-hydroxyethylacrylate, and 2,4,6-triallyloxy-1,3,5-triazine which are used as monomers and also a photo initiator (2,2-dimethoxy-2-phenylacetophenone) for its usage as optical sensor for gold ions. The thiol-ene based polymeric membrane sensor was characterized by using attenuated total reflectance-fourier transform infrared spectroscopy (ATR-FTIR) and scanning electron microscopy (SEM). The response characteristics of the sensors including dynamic range, pH effect, response time, and the effect of foreign ions were investigated. Fluorescence spectra showed that the excitation/emission maxima of the membrane were at 379/425 nm, respectively     

Adsorption mode of cinchonidine on Cu(111) surface

The adsorption mode of cinchonidine on Cu(111) was directly obtained by in situ STM. The molecules were found to adsorb on the substrate surface and form a long-range ordered adlayer with (4 x 4) symmetry. While the quinoline rings lie parallel to Cu(111), the chiral quinuclidine moiety extends out of the surface. The enantioselectivity of catalysts may relate to this special adsorption conformation of cinchonidine on the surface.     

Thin-film oxygen sensors using a luminescent polynuclear gold(I) complex

Robust thin-film oxygen sensors were fabricated by encapsulating a lipophilic, polynuclear gold(I) complex, bis{m-(bis(diphenylphosphino)octadecylamine-P,P′)}dichlorodigold(I), in oxygen permeable polystyrene and ormosil matrices. Strong phosphorescence, which was quenched by gaseous and dissolved oxygen, was observed from both matrices. The polystyrene encapsulated dye exhibited downward-turning Stern–Volmer plots which were well fitted by a two-site model. The ormosil trapped complex showed linear Stern–Volmer plots for dissolved oxygen quenching but was downward turning for gaseous oxygen. No leaching was observed when the ormosil based sensors were immersed in flowing water over an 8 h period. Both films exhibited fully reversible response and recovery to changing oxygen concentration with rapid response times.     

Dye@MOF composites (RhB@1): Highly sensitive dual emission sensor for the detection of pesticides,Fe3+ and ascorbate acid

With the rapid development of economy, industrial and agricultural pollutants have caused great damage to the ecological environment and the normal development of organisms, posing a serious threat to global public health. Therefore, rapid and sensitive detection of pollutants is very important for environmental safety and people’s health. A stable multi-response fluorescence sensor(RhB@1) with dual emission characteristics was constructed by embedding Rh B guest molecules in Zn-MOF using a simp...