Carbazole-functionalized polyfluorenes: synthesis and conformational properties in chloroform solution and β-phase formation in copolyfluorene films

Novel copolyfluorenes (CPFs) containing 2.5 or 10 mol% of carbazole-2,7-diyl (2,7-Cz) or carbazole-3,6-diyl (3,6-Cz) derivatives in the backbone have been synthesized by means of palladium-catalyzed Suzuki polymerization under microwave irradiation. The structure of the CPF polymers was also modified by insertion of additional 2-ethylhexyl or carbazole, diaryloxadiazole, or triphenylamine units via 3,6-Cz or 2,7-Cz comonomer units in the side chains of polymers. The self-organization of molecules in chloroform solutions was investigated using light scattering and within a wide concentration interval. Analysis of the behavior of the CPFs showed that the synthesized copolymers have an increased equilibrium rigidity of molecules with a Kuhn segment length A = (10–15) nm. The A value decreases with the introduction of Cz-units into the macromolecule in the meta-position. It is shown that chemical structure of the CPFs and thermal treatment in the temperature range 60–150 °C have a dominant effect on the optoelectronic properties as well as on microstructures of their films.     

Regioregular copolymers of 3-alkoxythiophene and their photovoltaic application

Low band gap conjugated polymers with proper energy levels for charge transfer are required to achieve high-efficiency polymer solar cells. We report the synthesis and characterization of two new regioregular copolymers that are based on 3-alkoxythiophene monomers: poly(3-octylthiophene-2,5-diyl-co-3-decyloxythiophene-2,5-diyl) (POT-co-DOT) and poly{(9,9-dioctylfluorene)-2,7-diyl-alt-[4,7-bis(3-decyloxythien-2-yl)-2,1,3-benzothiadiazole]-5',5' '-diyl} (PF-co-DTB). Compared to the alkyl substituents, the alkoxy side chains on the thiophene units can effectively lower the band gap of copolymers and enhance the charge transfer to electron acceptors such as (6,6)-phenyl C(61)-butyric acid methyl ester (PCBM). The chemical structure and regioregularity of the copolymers were confirmed by NMR. Both copolymers are readily soluble in organic solvents and form high-quality thin films. Electrochemical and photophysical studies reveal band gaps of 1.64 eV for POT-co-DOT and 1.78 eV for PF-co-DTB. Bulk heterojunction photovoltaic devices were fabricated using blends of these copolymers with PCBM as the active layer, ITO-glass as the anode, and aluminum as the cathode. Power conversion efficiency of 1.6% was obtained under simulated solar light AM 1.5 G (100 mW/cm(2)) from a solar cell with an active layer containing 20 wt % PF-co-DTB and 80 wt % PCBM. Regioregular poly(3-decyloxythiophene-2,5-diyl) (P3DOT) was also studied for comparison purposes.     

Synthesis and properties of fluorene or carbazole‐based alternating copolymers containing Si and vinylene units in the main chain

Alternating copolymerization of 9,9‐dihexyl‐2,7‐dibromofluorene (HFl), N‐hexyl‐2,7‐dibromocarbazole (2,7‐HCz) or N‐hexyl‐3,6‐dibromocarbazole (3,6‐HCz) with Si‐containing divinyl or diallyl compounds, divinyldimethylsilane, divinyldiphenylsilane, 1,3‐divinyltetramethyldisiloxane, 1,4‐bis(dimethylvinylsilyl)benznene, diallyldimethylsilane, or diallyldiphenylsilane has been investigated using Mizoroki‐Heck reaction with a Pd catalyst. The corresponding alternating copolymers were obtained in good yield. The alternating copolymers from HFl or 2,7‐HCz showed good solubility in typical organic solvents. On the other hand, the copolymer with 3,6‐HCz became insoluble due to the crosslinking. Photophysical properties of the resulting copolymers were investigated with UV–vis absorption and photoluminescence spectroscopy. All the copolymers showed absorption peak derived from π–π* transition at around 340 nm, which was blue shifted in comparison with that of the corresponding homopolymer. Whereas emission peaks of the copolymers of the cast film were red shifted in comparison with that of the homopolymers. Multiple broad absorption peaks, which would be derived from intramolecular charge transfer through σ–π moiety, were also detected in the range from 390 to 450 nm in the spectra of the copolymers containing Si‐vinylene unit. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4513–4521, 2008     

Quantifying the role of interfacial width on intermolecular charge recombination in block copolymer photovoltaics

Block copolymers have the potential to control the interfacial and mesoscopic structure in the active layer of organic photovoltaics and consequently enhance device performance beyond systems which rely on physical mixtures. When utilized as the active layer, poly(3‐hexylthiophene‐2,5‐diyl)‐block‐poly((9,9‐bis‐(2‐octyldodecyl)fluorene‐2,7‐diyl)‐alt‐(4,7‐di(thiophene‐2‐yl)?2,1,3‐benzothiadiazole)?5′,5″‐diyl) donor–acceptor block copolymers have recently demonstrated 3% power conversion efficiencies in devices. Nevertheless, the role of the interfacial structure on charge transfer processes remains unclear. Using density functional theory, we examined charge transfer rate constants in model interfaces of donor–acceptor block copolymers. Our results demonstrate that intermolecular charge recombination can depend on the interfacial breadth, where sharp interfaces (ca. 1 nm) suppress intermolecular charge recombination by orders of magnitude. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1224–1230     

Synthesis and characterization of white‐light‐emitting polyfluorenes containing orange phosphorescent moieties in the side chain

Two orange phosphorescent iridium complex monomers, 9‐hexyl‐9‐(iridium (III)bis(2‐(4′‐fluorophenyl)‐4‐phenylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐PIr) and 9‐hexyl‐9‐(iridium(III)bis(2‐(4′‐fluorophenyl)‐4‐methylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐MIr), were successfully synthesized. The Suzuki polycondensation of 2,7‐bis(trimethylene boronate)‐9,9‐dioctylfluorene with 2,7‐dibromo‐9,9‐dioctylfluorene and Br‐PIr or Br‐MIr afforded two series of copolymers, PIrPFs and MIrPFs, in good yields, in which the concentrations of the phosphorescent moieties were kept small (0.5–3 mol % feed ratio) to realize incomplete energy transfer. The photoluminescence (PL) of the copolymers showed blue‐ and orange‐emission peaks. A white‐light‐emitting diode with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/PIr05PF (0.5 mol % feed ratio of Br‐PIr)/Ca/Al exhibited a luminous efficiency of 4.49 cd/A and a power efficiency of 2.35 lm/W at 6.0 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.46, 0.33). The CIE coordinates were improved to (0.34, 0.33) when copolymer MIr10PF (1.0 mol % feed ratio of Br‐MIr) was employed as the white‐emissive layer. The strong orange emission in the electroluminescence spectra in comparison with PL for these kinds of polymers was attributed to the additional contribution of charge trapping in the phosphorescent dopants. © 2007 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 45: 1746–1757, 2007     

Triplet-state and singlet oxygen formation in fluorene-based alternating copolymers

Data are reported on the triplet states of a series of fluorene-based A-alt-B type alternating copolymers based on pulse radiolysis-energy transfer and flash photolysis experiments. From the pulse radiolysis experiments, spectra are given for eight copolymers involving phenylene, thiophene, benzothiadiazole, and oligothienylenevinylene groups. Quantum yields for triplet-state formation (PhiT) have been obtained by flash photolysis following laser excitation and in one case by photoacoustic calorimetry. In addition, yields of sensitized formation of singlet oxygen have been determined by time-resolved phosphorescence and are, in general, in excellent agreement with the PhiT values. In all cases, the presence of thiophene units is seen to increase intersystem-crossing quantum yields, probably because of the presence of the heavy sulfur atom. However, with the poly[2,7-(9,9-bis(2'-ethylhexyl)fluorene)-alt-1,4-phenylene] (PFP), thiophene S,S-dioxide (PFTSO2) and benzothiadiazole (F8BT) copolymers, low yields of triplet formation are observed. With three of the copolymers, the energies of the triplet states have been determined. With PFP, the triplet energy is virtually identical to that of poly[2,7-(9,9-bis(2'-ethylhexyl)fluorene)]. In contrast, with fluorene-thiophene copolymers PFaT and PF3T, the triplet energies are closer to those of thiophene oligomers, indicating that there is significant conjugation between fluorene and thiophene units but also that there is a more localized triplet state than with the homopolymers.     

Synthesis and Properties of Poly （aryl ether ketone） Copolymers Containing 2,7-Naphthalene Moieties

IntroductionPoly(aryl ether ketone)s are high performance en-gineering plastics with outstanding physical,chemical,thermal and mechanical properties and have been ap-plied to the aerospace industry,the electronic industry,the automobile industry,the petro…     

Synthesis and light‐emitting properties of carbazole‐based copolymers bearing cyano‐substituted arylenevinylene chromophore

Two arylenevinylene compounds bearing the cyano group at α‐position ( 6 ) and β‐position ( 9 ) from the dialkoxylphenylene unit were synthesized, in which the molecular termini were functionalized with 3‐bromocarbazole. The Suzuki coupling copolymerization of these compounds with 1,4‐bis[(3′‐bromocarbazole‐9′‐yl)methylene]‐2,5‐didecyloxybenzene and 9,9‐dihexylfluorene‐2,7‐bis(boronic acid) was carried out to obtain copolymers ( cp67 and cp97 ) containing the cyano‐substituted arylenevinylene fluorophore of 7 mol %. Model compounds ( 6 ′ and 9 ′) corresponding to the arylenevinylene fluorophore were also prepared. The UV spectra of copolymers resembled that of homopolymer hp with no arylenevinylene segment in both CHCl₃ solution and thin film. The emission maxima of copolymers in CHCl₃ (394 nm) agreed with that of homopolymer indicating that the emission bands originated from the carbazole‐fluorene‐carbazole segment. The emission maximum wavelength of copolymer cp67 in thin film (477 nm) indicated fluorescence from the cyano‐substituted arylenevinylene fluorophore because of the occurrence of fluorescence resonance electron transfer. In contrast, copolymer cp97 showed fluorescence at 528 nm to suggest the formation of a new emissive species such as a charge‐transfer complex (exciplex). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 91–98, 2010     

Isomeric effect of sulfonated poly(arylene ether)s comprising dihydroxynaphthalene on properties for polymer electrolyte membranes

Polymer electrolyte membranes (PEMs) made of sulfonated poly(arylene ether)s consisted of 3,3′‐disulfo‐4,4′‐dichlorodiphenylsulfone disodium salt, 2,6‐dichlorobenzonitrile, and one of three dihydroxynaphthalene isomers (2,6‐, 2,7‐, and 1,5‐dihydroxynaphthalene, abbreviated as 2,6‐N, 2,7‐N, and 1,5‐N, respectively) were prepared with similar level of inherent viscosity and ion exchange capacity, and structural effect of the catenation in dihydroxynaphthalene isomers on membrane properties was compared. In the case of membranes for PEM fuel cell application with relatively high ion exchange capacity around 2.1 mequiv/g, three copolymers showed almost the same proton conductivity; however, swelling in water increased with the following order: 1,5‐N < 2,6‐N < 2,7N. In the case of direct methanol fuel cell membranes with lower ion exchange capacity around 1.5 mequiv/g, no remarkable difference in proton conductivity was also observed in three isomeric copolymers and swelling property and methanol permeability were lower in 1,5‐N and 2,6‐N copolymers than 2,7‐N copolymer. These tendencies show that higher rigidity or energy barrier for conformational change of polymer chain gives better performance of PEM for fuel cells with superior dimensional stability. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Donor–acceptor semiconducting polymers based on pyromellitic diimide

Three donor–acceptor copolymers P1 , P2 , and P3 with N,N′‐dodecylpyromellitic diimide as the electron‐acceptor unit with three diethynyl‐substituted donor monomers: 1,4‐diethynyl‐2,5‐bis(octyloxy)benzene, 2,7‐diethynyl‐9,9‐dioctyl‐9H‐fluorene, and 3,3′‐didodecyl‐5,5′‐diethynyl‐2,2′‐bithiophene have been synthesized by Sonogashira crosscoupling polymerization. The synthesized polymers showed deep highest occupied molecular orbital energy levels and larger band gaps (>2.5 eV). Polymers P1 , P2 , and P3 underwent fluorescence quenching with [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM), indicating the intermolecular photo‐induced charge transfer between the donor polymers and the PCBM acceptor. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1617–1622     

A Quantum Chemical Study of the Ground and Excited State Electronic Structures of Carbazole Oligomers with and without Triarylborane Substitutes

Recent experimental investigation (Reitzenstein and Lambert,Macromolecules, 2009, 42, 773) indicated that the quite different optical properties of 2,7- and 3,6-linkage triarylboryl carbazole oligomers may arise from the different nature of their low-lying excited states: a low-lying delocalized within-backbone excitation in longer 2,7-linked oligomers vs a backbone-to-sidechain charge-transfer (CT) excitation independent of the polymerization length in 3,6-linked oligomers. Here in this paper, two long-range corrected functionals, CAM-B3LYP and ωB97X, are applied together with the traditional B3LYP functional in time-dependent density functional theory (TDDFT) calculations to systematically investigate the low-lying electronic excitations in both oligomers. Our calculations indicate that an extensive conjugation exists between monomer molecular orbitals in 2,7-linked oligomers, which is absent in those of 3,6-linked structures, resulting in a considerable narrowing of the HOMO-LUMO gap of their backbone moiety, while having little effect on the side-chains. CAM-B3LYP and ωB97x calculations confirm that the lowest-energy absorption is a within-backbone excitation in longer 2,7-linked oligomers as opposed to a backbone to side-chain charge transfer excitation in 2,7-linked oligmers of shorter length and 3,6-linked oligomers of any length. All these findings are consistent with the experimental findings and the qualitative energy diagram proposed by Reitzenstein and Lambert.     

Synthesis,characterization and luminescent properties of new copolymers of dimethacrylate derivatives of naphthalene‐2,7‐diol

Synthesis and characterization of new type photoluminescent, bulk copolymers of 2,7‐(2‐hydroxy‐3‐methacryloyloxypropoxy)naphthalene (2,7‐NAF.DM) with different vinyl comonomers (methyl methacrylate, 2‐hydroxyethyl methacrylate, butyl acrylate, divinylbenzene, styrene and N‐vinyl‐2‐pyrrolidone) are presented. The chemical structure of 2,7‐NAF.DM was confirmed by NMR, GC‐MS and elemental analysis. The copolymers were characterized by ATR and thermal (differential scanning calorimetry) analyses. Their luminescent properties were studied in terms of quantum efficiency (Φ_abs), which was shown to change in the range of 50–90% depending on the type of comonomer. It was found that the green‐emitting species in these polymers can be excited directly by low‐energy (400–520 nm) photoirradiation. These materials can be applied in the liquid or solid states in the form of powders, films or monoliths. Copyright © 2014 John Wiley & Sons, Ltd.     

含苯并硒二唑聚咔唑/芴类共轭聚电解质及其前驱体的合成与性能研究

采用Suzuki偶合反应合成了一系列新型的咔唑、芴和2,1,3-苯并硒二唑的共聚物——聚[3,6-(N-(2-乙基己基))咔唑-2,1,3-苯并硒二唑-9,9-双(N,N-二甲基胺丙基)芴](PCzN-BSeD)及其相应的聚电解质衍生物——聚[3,6-(N-(2-乙基己基))咔唑-2,1,3-苯并硒二唑-9,9-(双(3′-(N,N-二甲基)-N-乙基铵)丙基)芴]二溴(PCzNBr-BSeD).在聚咔唑和芴中引入不同比例的2,1,3-苯并硒二唑(BSeD)单元,引起了由咔唑和芴链段向窄带隙苯并硒二唑(BSeD)单元有效的能量转移.通过对聚合物电致发光性能的研究,发现用聚(3,4-亚乙基二氧基噻吩)(PEDOT)或聚(3,4-亚乙基二氧基噻吩)/聚乙烯咔唑(PEDOT/PVK)作为空穴传输层时,器件的性能相差不大,表明咔唑的引入较明显的改善了聚合物的空穴注入性能.而且几乎所有的聚合物用高功函数铝作阴极的器件和用钡/铝作阴极的器件具有相近的发光性能,表明这类聚合物具有良好的电子注入性能.     

Bipolar Blue Light-emitting Polyfluorenes Containing Dibenzothiophene-S,S-dioxide/Carbazole Units

Bipolar blue light-emitting polyfluorenes(PFSO-Cz) containing electron-deficient dibenzothiophene-S,S-dioxide(SO) and electron-rich carbazole(Cz) unit were synthesized. All the polymers show a high thermal stability with the decomposition temperatures over 400℃ and higher photoluminescence quantum yields. The highest occupied molecular orbital energy levels(E_HOMO's) slightly enhance and the lowest unoccupied molecular orbital energy levels(E_LUMO's) gently depress with the increase of Cz content in the polymers. PL spectra of the polymers display remarkable red shift and broadening with the increase of solvent polarities, indicating significant intramolecular charge transfer(ICT) effect in the polymers. Electroluminescence(EL) spectra of the polymers exhibit a broadening tendency with increasing the content of Cz unit in the polymers. The superior device performances were obtained with the maximum luminous efficiency(LE­_max) of 5.2 cd/A, the maximum external quantum efficiency(EQE_max) of 4.8% and the Internationale de l'Eclairage(CIE)(x,y) coordinates of (0.16, 0.17) for PFSO15-Cz10 based on the single-layer device of ITO/PEDOT:PSS/EL/CsF/Al. The results indicate that the efficient bipolar blue light-emitting polyfluorenes are also constructed by Suzuki copolymerization using the monomers in common use.     

Intramolecular charge transfer complexes—25. Copolymers of N-ethyl-3-hydroxymethyl phenothiazinyl acrylate and methacrylate with acryloyl and methacryloyl-β-hydroxyethyl-3,5-dinitrobenzoate

Copolymers with pendant electron-donor and electron-acceptor groups (phenothiazine and dinitrobenzoate type respectively) have been studied. The formation and the participation in the reaction of an intermonomer charge transfer complex was indicated by considering the copolymerization data and by means of electronic absorption and ¹H-NMR spectra. It was concluded from NMR spectra that the acrylate-acrylate copolymers are stronger charge transfer complexes than the methacrylate-methacrylate copolymers.     

Alternating oligo(p-phenylene vinylene)--perylene bisimide copolymers: synthesis,photophysics, and photovoltaic properties of a new class of donor--acceptor materials

A Suzuki polycondensation reaction has been used to synthesize two copolymers consisting of alternating oligo(p-phenylene vinylene) (OPV) donor and perylene bisimide (PERY) acceptor chromophores. The copolymers differ by the length of the saturated spacer that connects the OPV and PERY units. Photoinduced singlet energy transfer and photoinduced charge separation in these polychromophores have been studied in solution and in the solid state via photoluminescence and femtosecond pump-probe spectroscopy. In both polymers a photoinduced electron transfer occurs within a few picoseconds after excitation of the OPV or the PERY chromophore. The electron transfer from OPV excited state competes with a singlet energy transfer state to the PERY chromophore. The differences in rate constants for the electron- and energy-transfer processes are discussed on the basis of correlated quantum-chemical calculations and in terms of conformational preferences and folding of the two polymers. In solution, the lifetime of the charge-separated state is longer than in the films where geminate recombination is much faster. However, in the films some charges are able to escape from geminate recombination and diffuse away and can be collected at the electrodes when the polymers are incorporated in a photovoltaic device.     

Theoretical studies of the effect of electron-withdrawing dicyanovinyl group on the electronic and charge-transport properties of fluorene-thiophene oligomers

At the quantum-chemical level, we characterize some important parameters that control photoelectronic properties of three π-conjugated fluorene-thiophene oligomers namely, 2,7-di(2-thienyl)-9,9-dihexylfluorene, 2,5-Bis-(9H-fluorene-2-yl)-thieno[3,2-b]thiophene and 2,7-Bis[5-(1,1-dicyanovinyl)thiophene-2-yl]-9,9-di-n-hexylfluorene (FTCN). The geometric and electronic structures of these compounds in the ground and the lowest singlet excited states were studied using density function theory. By employing the incoherent transport model, the electron and hole mobilities were evaluated on a wide variety of nearest-neighbor charge transfer pathways. These results show that the chemical modifications by changing linkage mode or introducing the electron-withdrawing group could improve the charge transfer, especially for FTCN. Meanwhile, it is found that the packing effect weakens the emission intensity to some extent according to the simulations of photoluminescences of dimers.     

Theoretical studies of the modulation of polymer electronic and optical properties through the introduction of the electron-donating 3,4-ethylenedioxythiophene or electron-accepting pyridine and 1,3,4-oxadiazole moieties

One serious problem associated with polyfluorene and derivatives (PFs) as blue luminescent polymers is the significant energy barrier for hole or electron injections; thus they usually face charge injection and transport difficulties with the currently available cathode and anode materials. The incorporation of an electron-donating or -accepting unit is expected to improve the recombination of the charge carriers. In this paper, we apply quantum-chemical techniques to investigate three fluorene-based copolymers, copoly(2,5-ethylenedioxythiophene-alt-9,9'-dimethylfluorene) (PEF), copoly(2,5-pyridine-alt-9,9'-dimethylfluorene) (PPyF), and poly[(fluorene-2,7-diyl)-alt-(1,3,4-oxadiazole-2,5-diyl)] (PFO), in which Delta(H)(-)(L) [the energy difference between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), when n = infinity], the lowest excitation energies (E(g)), ionization potentials (IP), electron affinities (EA), and lambda(abs) and lambda(em) are fine-tuned by the regular insertion of electron-donating unit 3,4-ethylenedioxythiophene (EDOT) or electron-withdrawing units pyridine and 1,3,4-oxadiazole. The results show that the alternate incorporation of electron-donating moiety EDOT increases the HOMO energy and thus reduces the IPs, and consequently the hole injection was greatly improved. On the other hand, even though both kinds of charge carriers will improve the electron-accepting ability, the results show that electron-withdrawing moieties greatly facilitate the electron-transporting. Especially in PFO, the highly planar structural character resulted from the strong push-pull effect between the fluorene ring and the 1,3,4-oxadiazole ring and a weak interaction between the nitrogen and oxygen atoms in 1,3,4-oxadiazole ring and the hydrogen atom of the fluorene ring, significantly lowering the LUMO energy levels and thus improve the electron-accepting and transporting properties by the low LUMO energy levels.     

Time‐dependent density functional theory study of electronic spectrum property for carbazolyl–pyridinyl alternating copolymers

Three A‐B‐type fluorescent copolymers comprised of alternating carbazolyl and pyridinyl units, poly[(2,7‐(N‐(2‐ethylhexyl)carbazolyl)‐alt‐(3,5‐pyridinyl))](PEHCP‐35), poly[(2,7‐(N‐(2‐ethylhexyl)carbazolyl)‐alt‐(2,6‐pyridinyl))] (PEHCP‐26) and poly[(2,7‐(N‐(2‐ethyl‐hexyl)carbazolyl)‐alt‐(2,5‐pyridinyl))] (PEHCP‐25), are studied by means of the density functional theory (DFT/B3LYP/6‐31G). Based on the optimized geometries, the optical properties are calculated by employing time‐dependent density functional theory (TD‐DFT). The bandgaps and optical properties are saturated quickly in PEHCP‐35 and PEHCP‐26. It is known from experiment that PEHCP‐25 is actually an oligomer with a polymerization degree of 4. So the tetramers of PEHCP‐35, PEHCP‐26, and PEHCP‐25 are adopted to study the electronic and optical properties, and the calculated results are in close agreement with experiment. The calculated bandgaps of copolymers obtained from two ways, i.e., HOMO–LUMO gaps and the lowest excitation energies, decrease in the following order PEHCP‐35 > PEHCP‐26 > PEHCP‐25, the same trend as the data obtained from the edge of the electric band but different from the electrochemically obtained data from experiment (PEHCP‐25 > PEHCP‐26 > PEHCP‐35). The outcomes showed that, when excited, a charge transfer from carbazolyl unit to pyridinyl unit occurs, and the lumophor is mainly carbazolyl units. The UV absorption and emission wavelengths both exhibit bathochromic shifts: PEHCP‐35 < PEHCP‐26 < PEHCP‐25. © 2006 Wiley Periodicals, Inc. Int J Quantum Chem, 2007     

Bipolar molecules with high triplet energies: synthesis, photophysical, and structural properties

This article sheds new light on the interplay of electronic and conformational effects in luminescent bipolar molecules. A series of carbazole/1,3,4-oxadiazole hybrid molecules is described in which the optoelectronic properties are systematically varied by substituent effects which tune the intramolecular torsion angles. The synthesis, photophysical properties, cyclic voltammetric data, X-ray crystal structures, and DFT calculations are presented. Excited state intramolecular charge transfer (ICT) is observed from the donor carbazole/2,7-dimethoxycarbazole to the acceptor phenyl/diphenyloxadiazole moieties. Introducing more bulky substituents onto the diphenyloxadiazole fragment systematically increases the singlet and triplet energy levels (E(S) and E(T)) and blue shifts the absorption and emission bands. The triplet excited state is located mostly on the oxadiazole unit. The introduction of 2,7-dimethoxy substituents onto the carbazole moiety lowers the value of E(S), although E(T) is unaffected, which means that the singlet-triplet gap is reduced (for 7bE(S) - E(T) = 0.61 eV). A strategy has been established for achieving unusually high triplet levels for bipolar molecules (E(T) = 2.64-2.78 eV at 14 K) while at the same time limiting the increase in the singlet energy.