高温水热合成具有高稳定性的有序介孔材料

高温水热合成路线作为合成具有超高稳定性的介孔材料越来越受到人们的重视.本文对高温水热合成有序介孔材料的发展过程作一个简单的综述,合成路线包括使用碳氟表面活性剂和碳氢表面活性剂作为复合模板,有机季铵盐与碳氢表面活性剂作为复合模板以及最近报道的采用碳氢表面活性剂作为单一模板来合成系列的有序介孔材料,其组成为二氧化硅、氧化钛硅以及聚合物等.     

Characterization and Catalytic Behavior of Nano Pt/MgO Catalysts

"Pt/MgO catalysts were prepared by using wet impregnation method. X-ray diffraction, transmission electron microcopy (TEM), electron spectroscopy for chemical analysis, and temperature programmed surface reaction (TPSR) were used to characterize the calcined and used catalysts. Partial Oxidation of Methane (POM) to synthesis gas was carried out in a fixed bed micro-reactor to test the catalytic activity. TEM images revealed that Pt particles have the size of less than 10 nm, the size of the support MgO is about 50-200 nm. At 800 oC, the Pt/MgO catalyst exhibited a very high activity and stability for POM reaction. Both the conversion of methane and selectivities to CO and H2 remained almost constant up to 120 h. The dispersed Pt existed in the metallic state. The state and the dispersion of active Pt and the structure of support MgO were very stable, together with the high ability to resist carbon deposition, made the catalysts show a very high stability for POM under stoichiometric reaction conditions."     

Properties of Interface between Platinum Sponge and Solid Electrolyte Na5TbSi4O12in an Oxygen Atmosphere at Moderate Temperatures: Effect of the Platinum Grain Size

The behavior of electrochemical cells Pt(sponge)/Na₅TbSi₄₁₂/Na_0.65Co₂(cell I) and Pt(sponge)/Na₅TbSi₄₁₂/Pt(sponge) (cell II) is studied by, respectively, potentiometric and impedance methods in oxygen and argon atmospheres at 50–300°C. Dependence of potential of cell I on the oxygen concentration is affected by the grain size of platinum sponge and the temperature. At 50–200°C the coarse-grained platinum electrode in contact with solid electrolyte Na₅TbSi₄₁₂ exhibits an oxygen function characterized by the potential-determining reaction ₂(g) + ₂ + 2 = ^– ₂ + ^–. An impedance method shows the triple-phase boundary ₂, Pt(sponge)/Na₅TbSi₄₁₂ to be reversible with respect to oxygen. The reversibility is realized by minority charge carriers in the solid electrolyte, i.e. by oxygen ions.     

Kinetic Evidence for the Influence of Subsurface Oxygen on Palladium Surfaces Towards CO Oxidation at High Temperatures

Transient state kinetics of the catalytic oxidation of CO with O₂ on Pd‐surfaces has been measured under isothermal conditions by using a molecular beam approach. Systematic studies were carried out as a function of reaction temperature and CO+O₂ composition. With sufficient kinetic evidence, we have demonstrated the positive influence of subsurface oxygen towards CO‐adsorption and oxidation to CO₂ at high temperatures (600–900 K) on Pd‐surfaces, and the likely electronic nature of the surface changes with oxygen in the subsurface. These studies also provide a direct proof for CO‐adsorption with a significantly reactive sticking coefficient at high temperatures on Pd‐surfaces exhibiting a significant subsurface O‐coverage.     

高温非平衡条件下氟原子亲电动力学的激波管研究

To study electron affinity kinetics, a shock tube method was applied, in which the test gas was ionized by a reflected shock wave and subsequently quenched by a strong rarefaction wave. As the quenching speed of 106 K/s was reached, a nonequilibrium ionization recombination process occurred, which was dominated by ion recombination with electrons. A Langmuir electrostatic probe was used to monitor variation in the ion number density at the reflection shock region. The working state of the probe was analyzed, and a correction was introduced for reduction of the probe current due to elastic scattering in the probe sheath. The three body electron affinity rate coefficient of the fluorine atom over the temperature range 1200 to 2200 K in an ambiance of argon gas was directly determined. The temperature dependence of electron affinity rate coefficient was discussed.     

黄原胶热氧稳定性的研究

黄原胶(Xanthangum)是一种生物高分子化合物。它具有许多优异的性能,如:增粘性、悬浮性、耐酸碱等,并有很高的经济价值。对黄原胶的耐热性国外已有报导,KangK.S.等提到黄原胶加热至121℃、15分钟不失重。但黄原胶热稳定性如何、能耐多高的温度等尚未见报导。     

Pt／钇稳定氧化锆固体电解质在高温下的电化学性质

用交流阻抗技术研究了二电极、三电极Ｐｔ／钇稳定氧化锆（简称ＹＳＺ）高温固体电化学体系．开路电位下，Ｐｔ／ＹＳＺ体系只有一个阻抗半圆，对应于电极体系的电化学活化控制过程，极化电阻随温度变化的表观活化能为１７１．５ｋＪ／ｍｏｌ．Ｐｔ／ＹＳＺ界面的双电层电容约为３００μＦ／ｃｍ２．阳极极化下，交流阻抗极化电阻显著减小；阴极极化下，极化电阻反而增大，并出现浓差控制现象．     

Cu掺杂对Pt/Ba/CuxMg1-xAl2O4催化剂高温稀燃NOx消除性能的影响

制备了一系列不同Cu掺杂量的Pt/Ba/Cu_xMg_1-xAl₂O₄(x=0, 0.1, 0.3)催化剂, 将其应用于高温NO_x储存还原(NSR)反应, 并探究了Cu掺杂量对催化剂NO_x消除性能的影响. 结果表明, 储存组分BaCO₃在NSR过程中存在再分散现象. 高温时催化剂的NO_x消除性能取决于其NO_x储存量, 而不是NO氧化和NO_x还原性能. 高温时催化剂的NO_x储存量与其上硝酸盐的热稳定性密切相关, Pt/Ba/MgAl₂O₄上NO_x主要以离子态硝酸盐形式存在, 而掺杂Cu后催化剂上的NO_x又增加了单齿硝酸盐的存在形式, 单齿硝酸盐具有更高的热稳定性, 因此掺Cu催化剂具有更大的NO_x储存量. 在450~500 ℃范围内, Cu的掺杂显著提高了Pt/Ba/MgAl₂O₄的NO_x消除性能; Pt/Ba/Cu_0.1Mg_0.9Al₂O₄催化剂的性能最佳, 450 ℃时的NO_x消除效率高达90%.     

氧气在不同粒径Pt/C催化剂上的电催化还原

在甲醇溶剂中,利用SnCl₂作为还原剂,通过控制反应条件制备了带有不同粒径Pt粒子Pt/C催化剂。X-射线衍射和透射电镜的研究表明获得的Pt/C催化剂中Pt粒子具有高度的均一性和良好的分散度。电化学研究显示,对于氧气的电催化还原,Pt/C催化剂存在着明显的粒径效应。当Pt粒子粒径为3.2nm时,Pt/C催化剂对氧气的电催化还原的质量比活性最佳。Pt/C催化剂对氧气的粒径效应可能与其表面含氧基团含量、Pt粒子的比表面积及其晶面结构相关。     

氧气在不同粒径Pt/C催化剂上的电催化还原

在甲醇溶剂中,利用SnCl2作为还原剂,通过控制反应条件制备了带有不同粒径Pt粒子Pt/C催化剂。X-射线衍射和透射电镜的研究表明获得的Pt/C催化剂中Pt粒子具有高度的均一性和良好的分散度。电化学研究显示,对于氧气的电催化还原,Pt/C催化剂存在着明显的粒径效应。当Pt粒子粒径为3.2 nm时,Pt/C催化剂对氧气的电催化还原的质量比活性最佳。Pt/C催化剂对氧气的粒径效应可能与其表面含氧基团含量、Pt粒子的比表面积及其晶面结构相关。     

Pt/C和Pt/CNTs电极的电化学稳定性研究

采用恒电位氧化法研究了Pt/C和Pt/CNTs电极的电化学稳定性. 相同条件下, Pt/C电极的氧化电流大约为Pt/CNTs电极的2倍; 120 h氧化后, Pt/C电极Pt的电化学表面积下降了21.3%, 而Pt/CNTs电极仅下降了7.6%, 表明Pt/CNTs电极性能衰减较慢. X射线光电子能谱(XPS)分析表明, Pt/C的载体碳黑表面氧增加量大于Pt/CNTs中碳纳米管(CNTs)表面氧的增加量, 说明碳黑的被氧化程度较高, 电化学稳定性差; Pt的表面化学状态没有发生变化; 碳纳米管本身的抗电化学氧化性也大于碳黑. 所以, 载体的被氧化程度不同是两种电极性能衰减不同的主要原因之一, 并且排除了Pt表面状态的影响.     

负载型Pt/C催化剂的制备条件对Pt晶粒尺寸的影响

纳米级催化剂;浸渍还原法;晶粒结构;负载型Pt/C催化剂的制备条件对Pt晶粒尺寸的影响     

Effects of Capping Agents on the Oxygen Reduction Reaction Activity and Shape Stability of Pt Nanocubes

We investigated the formation of Pt nanocubes (NCs) and their electrocatalytic oxygen reduction reaction (ORR) properties and structural stability using two different capping agents, namely, polyvinylpyrrolidone (PVP) and oleylamine (OAm). The mono-dispersity of the obtained Pt NCs and their interactions with PVP and OAm were analyzed by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), Fourier-transformed infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The TEM data show a high mono-dispersity (82 %) and a large mean particle size (9-10 nm) for the Pt NCs obtained by the oleylamine-assisted method compared to those prepared via the PVP-assisted procedure (68 %, 6–7 nm). FTIR, XPS, and TGA data show that PVP and OAm still remain at the Pt surface, despite washing. Interestingly, the OAm-capped Pt NCs show significantly higher electrochemically active surface area (ECSA) and ORR activity than the PVP-capped ones. An accelerated stress protocol, however, reveals that the OAm-capped NCs possess a poor structural stability during electrochemical cycling. The loss of a defined surface arrangement in the NCs is connected with a transformation into a near-spherical particle shape. In contrast, the PVP-capped NCs mainly retain their particle shape due to their strong capping behavior. In addition, we have developed a degradation model for NCs as a function of electrochemical parameters such as upper potential and cycle number. Altogether, we provide fundamental insights into the electronic interactions between capping agent and Pt NCs and the role of the adsorption strength of the capping agent in improving the electrochemical ORR performance as well as the structural stability of shape-controlled nanoparticles.     

酸性介质中1,2-丙二醇在铂电极上吸附和氧化过程的原位FTIR反射光谱研究

应用电化学循环伏安和原位FTIR反射光谱研究1,2-丙二醇在Pt电极上吸附和氧化过程。结果指出1,2-丙二醇的电氧化可按双途径进行。其一经1,2-丙二醇在Pt上解离吸附产物氧化至CO_2。但在较低电位下这些解离吸附产物(红外检测为CO_(ad)、[﹥C=CH_2]_(ad)等)累积吸附于电极上, 毒化Pt表面抑制其它反应。当电位大于0.3 V后它们一经生成即氧化脱附, 从而使1,2-丙二醇得以在未毒化Pt表面经反应中间体氧化至CO_2。在实验条件下,原位FTIR反射光谱检测到的反应中间体可能有HOC-CHOHCH_3(或CH_2OHCOCH_3)和HOOC-COCH_3(或HOOC-CHOHCH_3)等物种。     

十氢萘/空气混合物高温着火延迟的激波管测量

在激波管上进行了气相十氢萘/空气混合物的着火延迟测量, 着火温度为950-1395 K, 着火压力为1.82×10⁵-16.56×10⁵ Pa, 化学计量比分别为0.5、1.0 和2.0. 在侧窗处利用反射激波压力和CH^*发射光来测出着火延迟时间. 系统研究了着火温度、着火压力和化学计量比对十氢萘着火延迟时间的影响. 实验结果显示着火温度和着火压力的升高均会缩短着火延迟时间. 首次在相对高和低压的条件下观察到了化学计量比对十氢萘着火延迟的影响是完全相反的. 当压力为15.15×10⁵ Pa时, 富油混合物呈现出最短的着火延迟时间, 而贫油混合物的着火延迟时间却是最长的. 相反, 当压力为2.02×10⁵ Pa时, 富油混合物的着火延迟时间最长. 着火延迟数据与已有的动力学机理的预测值进行对比, 结果显示机理在所有的实验条件下均很好地预测了实验着火延时趋势. 为了探明化学计量比对着火延迟时间影响的本质, 对高、低压条件下的着火延时进行了敏感度分析.结果显示, 压力为2.02×10⁵ Pa时, 控制着火延迟的关键反应为H+O₂=OH+O, 而涉及十氢萘及其相应自由基的反应在15.15×10⁵ Pa时对着火延迟起主要作用.     

Galvanostatic Studies on Reduction of Oxygen at Silver Electrode

Galvanostatic studies with low current density in 0.1 N KNO₃ medium reveal that reduction of oxygen at silver electrode is totally irreversible and in the range of oxygen concentration studied, 2.2-306.3×10^?9 mole/cm³, the E-log [0₂] plot consists of two straight lines, one has a slope of 0.12 volts/decade (C>1 ppm up to air-saturated) and the other, 0.72 volts/decade (0.1<C<0.8 ppm). The transfer coefficient, α, the heterogeneous rate constants, k^o_fh and k^o_gh were evaluated to be 0.12, 2.8×10^?4, 1.6×10^?7 for the higher concentration range, and 0.02, 4.4×10^?4 for the lower concentration region respectively. A possible analytical method for tenths ppm level of oxygen is suggested.     

Inhibition of Reduction Current of Oxygen by Cysteine and Glutathione at Smooth Platinum Electrodes

Abstract

The reduction of molecular oxygen is inhibited by the chemisorption of cysteine and glutathione on the smooth platinum electrode. The cathodic current of the molecular oxygen reduction is dependent on the concentration of both substances.     

甲醇对炭载铂和四羧基酞菁钴催化氧还原动力学的影响

运用旋转圆盘电极技术和线性扫描伏安方法研究比较了甲醇对炭载铂（Pt/C）和800 ℃热处理的炭载四羧基酞菁钴（CoPcTc/C）催化氧还原动力学的影响.结果表明，对于Pt/C催化剂，在大于0.64 V和小于0.18 V（vs SCE）的电位范围，甲醇的氧化和氧的还原互不影响，而在其它电位范围，甲醇使Pt/C催化氧还原的性能严重降低.对于800 ℃热处理的CoPcTc/C，在整个电位范围内，甲醇的存在对氧还原都没有影响，是一种活性较高、耐甲醇能力强的氧还原电催化剂.     

Surface and Subsurface Oxygen on Platinum in a Perchloric Acid Solution

The oxidation of polycrystalline platinum in perchloric acid is studied by cyclic voltammetry at a potential scan rate of 0.1 V s^–1 in various potential cycling ranges. The earlier model for the formation of a barrier layer of strong complexes consisting of subsurface oxygen O_ss, platinum atoms, and anions adsorbed on the latter is shown to correctly describe experimental results on the platinum oxidation in sulfuric and perchloric acids. The regularities in these acids are on the whole similar. A weaker adsorption of perchlorate anions as compared with bisulfate facilitates chemisorption of oxygen at 0.7–0.85 V and hinders exchange by sites Pt O at 0.85–1.35 V. A prolonged potential cycling with a cathodic limit of 0.27 V and low anodic limits leads to the accumulation of surface complexes O_ss–Pt _n –ClO₄, which hinder both the oxygen chemisorption and the exchange Pt O below 1 V. At more positive potentials, the complexes are destroyed and oxygen penetrates into subsurface platinum layers.