Living carbocationic polymerization of isobutyl vinyl ether and the synthesis of poly[isobutylene-b-(isobutyl vinyl ether)]

The MeCH(O-i-Bu)Cl/TiCl₄/MeCONMe₂ initiating system was found to induce the rapid living carbocationic polymerization (LC^⊕Pzn) of isobutyl vinyl ether (IBuVE) at ?100°C. Degradation by dealcoholation which usually accompanies the polymerization of alkyl vinyl ethers by strong Lewis acids is “frozen out” at this low temperature and poly(isobutyl vinyl ether)s (PIBuVEs) with theoretical molecular weights up to ca. 40,000 g/mol (calculated from the initiator/monomer input) and narrow molecular weight distributions (M?_w/M?_n ≤ 1.2) are readily obtained. According to ¹³C-NMR spectroscopy, PIBuVEs prepared by living polymerization at ?100°C are not stereoregular. The MeCH(O-i-Bu)Cl/TiCl₄ combination induces the rapid LC^⊕Pzn of IBuVE even in the absence of N,N-dimethylacetamide (DMA). The addition of the common ion salt, n-Bu₄NCl to the latter system retards the polymerization and meaningful kinetic information can be obtained. The kinetic findings have been explained in terms of TiCl₄. IBuVE and TiCl₄ · IBuVE and TiCl₄ · PIBuVE complexes. The HCl (formal initiator)/TiCl₄/DMA combination is the first initiating system that can be regarded to induce the LC^⊕Pzn of both isobutylene (IB) and IBuVE. Polyisobutylene (PIB)–PIBuVE diblocks were prepared by sequential monomer addition in “one pot” by the 2-chloro-2,4,4-trimethylpentane (TMP-Cl)/TiCl₄/DMA initiating system. Crossover efficiencies are, however, below 35% because the PIB^⊕ + IBuVE → PIB-b-PIBuVE^⊕ crossover is slow. © 1993 John Wiley & Sons, Inc.     

Low-temperature polymerization of isobutyl vinyl ether

Isobutyl vinyl ether has been polymerized under conditions well known to yield isotactic polymer, viz., with boron trifluoride etherate at 78°C. in a nonpolar hydrocarbon diluent. A particular mixed solvent ratio and previous dissolution of catalyst enabled the polymerization to proceed homogeneously at the beginning. By following the temperature rise in an initially thermostatted system, we showed that the progress of the reaction eventually proceeded via a homogeneous phase to a gellike phase. Isotactic polymer is shown to be produced in both steps by a mechanism of slow chain propagation.     

Free-ionic polymerization of isobutyl vinyl ether by radiation

Radiation-induced free-ionic polymerization of isobutyl vinyl ether in bulk system has been studied by dilatometry and electrical conductivity measurement. Some refinements in kinetic treatment of estimate the propagation rate constant k_p from the rate of polymerization and steady-state conductivity were attempted. Polymerization of superdried monomer which gave a half-power dose-rate dependence of R_p was carried out at 0, 25, and 50°C. The k_p value obtained at 25°C and an activation energy for propagation were estimated as 1.2 ± 0.4 × 10⁵ I./mole-sec and 9.6 ± 2.8 kcal/mole, respectively. In isobutyl vinyl ether, a propagation reaction in free-ionic mechanism was found to be characterized with a high frequency factor and presumably higher activation energy, compared with ion-pair mechanism. Discussions were also made as to several contrasting behaviors between the polymerization of alkyl vinyl ethers and other vinyl monomers as styrene both in free-ion and ion-pair mechanisms.     

Living cationic polymerization of isobutyl propenyl ether as β-substituted vinyl ether

Isobutyl propenyl ether [IBPE; CH₃CH=CH? OCH₂CH(CH₃)₂] was polymerized with a mixture of hydrogen iodide and iodine (HI/I₂ initiator) in n-hexane at ?40°C to yield living polymers with a nearly monodisperse molecular weight distribution (MWD) (M?_w/M?_n ≈ 1.1). The number-average molecular weight (M?_n) of the polymers increased proportionally to IBPE conversion and further increased when a new monomer feed was added to a completely polymerized solution. The M?_n was controlled by the initial concentration of hydrogen iodide if the acid was charged in excess over iodine. In polymerization by iodine alone the M?_n of the polymers obtained in nonpolar solvents (n-hexane and toluene) also increased with conversion, but their MWD was broader (M?_w/M?_n = 1.3–1.4) than in the HI/I₂-initiated systems under similar conditions. The iodine-initiated polymerization in polar CH₂Cl₂ solvent, in contrast, led to nonliving polymers with a broad MWD (M?_n/M?_n = 1.6–1.8) and M?_n, independent of conversion. The living polymerization of IBPE was also compared with that of the corresponding isobutyl vinyl ether, to determine the effect of the β-methyl group in IBPE.     

Radiation-induced ionic polymerization of isobutyl vinyl ether in bulk

The radiation-induced ionic polymerization of isobutyl vinyl ether was investigated under conditions where the monomer was dried with molecular sieves. The investigation covered the temperature range from ?16°C to 90°C, and the dose-rate range from 10¹⁵ to 10²⁰ eV/g-sec, using both γ-rays and electrons. A very high overall activation energy of 15.9 kcal/mole was found for the process below 30°C. Above 30°C, however, the value of the overall activation energy dropped to 4.9 kcal/mole, a phenomenon which is ascribed to the solvation of the propagating carbonium ion below 30°C. The dose-rate dependence of the rate of polymerization was found to be 0.58 over the entire dose-rate range investigated. The molecular weight of the polymer was found to be far less sensitive to trace amounts of water than the rate of polymerization. The molecular weight of the polymer depended strongly on the irradiation temperature, reaching a maximum value of about 120,000 at 35°C. It is shown that at temperatures above 20°C regenerative chain transfer processes play an important role in determining the molecular weight of the polymer.     

Stereospecific polymerization of isobutyl vinyl ether catalyzed by calcined iron sulfate

The polymerization of isobutyl vinyl ether was studied in a heterogeneous system using iron (II) sulfate calcined in air at various temperatures as a catalyst. The maximum activity was shown by the catalyst calcined at 700°C, which effected the polymerization at room temperature in a few seconds, while the sulfate treated at 750°C was totally inactive. Poly(vinyl ethyl ether) was also obtained by the FeSO₄ (700°C) catalyst at room temperature. This catalyst formed the crystalline polymer (melting temperature 135–138°C) when the reaction was performed in toluene as solvent at room temperature. Poisoning experiments with Hammett indicators were carried out with the FeSO₄ (700°C) catalyst. The treatment with n-butylamine rendered it inactive in the reaction of isobutyl vinyl ether, while its catalytic activity was little affected by dicinnamalacetone. On the basis of the observed results, the nature of active sites of catalyst is discussed.     

Living cationic polymerization of isobutyl vinyl ether by the carboxyl group of the carbon black/zinc chloride initiating system

The effect of zinc chloride (ZnCl₂) on the cationic polymerization of isobutyl vinyl ether (IBVE) initiated by carboxyl groups on a carbon black surface was investigated. Although the polymerization of IBVE was initiated by carboxyl groups on the surface, the rate of polymerization was small and the molecular weight distribution (MWD) of poly IBVE was very broad. The rate of the polymerization was found to be drastically increased, and 100% monomer conversion was achieved in a short time by the addition of ZnCl₂. The number-average molecular weights (M_n) of the polyIBVE were directly proportional to monomer conversion in the polymerization initiated by the carbon black/ZnCl₂ system. By addition of the monomer at the end of the first-stage polymerization, the added monomer was smoothly polymerized at the same rate as in the first stage. The M_n of the polymer was in excellent agreement with the calculated value, assuming the polyIBVE chain forms per unit carboxyl group on the surface and MWD was narrow (M_w/M_n = 1.2 ～ 1.3). Based on the results, it is concluded that carbon black/ZnCl₂ system has an ability to initiate the living cationic polymerization of IBVE. Furthermore, it was found that polyIBVE was grafted onto the carbon black surface after the quenching of the living polymer with methanol. © 1995 John Wiley & Sons, Inc.     

Lifetime of living polymers in cationic polymerization. II. Living polymerization of isobutyl vinyl ether initiated by the hydrogen iodide/zinc halide systems

In the living cationic polymerization of isobutyl vinyl ether (IBVE) initiated by the hydrogen iodide/zinc halide (HI/ZnX₂; X = I, Br, Cl) systems, the concentration ([P^*]) of the living propagating species was determined by quenching with sodiomalonic ester ( 1 ). The quenching reaction was shown to be clean, instantaneous, and quantitative to give poly (IBVE) with a terminal malonate group from which [P^*] was obtained by ¹H-NMR spectroscopy. In the polymerizations in toluene below +25°C, [P^*] was constant and equal to the initial concentration ([HI]₀) of hydrogen iodide, independent of the type and concentrations of ZnX₂ as well as monomer conversion. At 0 and +25°C, however, the living species started decaying immediately after the complete consumption of monomer. In contrast, such a decay process was absent at ?15°C even in the absence of monomer until about an hour (depending on the conditions) after the end of polymerization. The deactivation reaction was first order in [P^*], and the lifetime (half-life) of the living species was longer at lower temperature and at lower ZnX₂ concentration. On the basis of these [P^*] and lifetime measurements, the HI/ZnX₂ systems were also compared with the HI/I₂ counterpart.     

Spontaneous polymerization of the nitroethylene–isobutyl vinyl ether system

Initiation and propagation mechanisms of the spontaneous polymerization of the system nitroethylene–isobutyl vinyl ether were studied. An equimolar mixture of these two monomers gives white precipitates below room temperature, though they react explosively to give viscous products at higher temperature. The precipitate was found to be composed of a polynitroethylene and a cycloadduct of these two monomers. The isolated cycloadduct product is so reactive that it not only polymerizes itself spontaneously but also initiates the polymerization of nitroethylene. The polymerization of the cycloadduct was revealed to proceed without termination to produce an alternate copolymer of these two monomers. These results indicate that the explosive spontaneous polymerization of this system consists of three elementary reaction processes; (1) cycloaddition reaction between two monomers, (2) anionic polymerization of nitroethylene induced by the cycloadduct, and (3) the living ring-opening polymerization of the cyclo-adduct.     

Living cationic polymerization of 2‐adamantyl vinyl ether

Living cationic polymerization of 2‐adamantyl vinyl ether (2‐vinyloxytricyclo[3.3.1.1]^3,7decane; 2‐AdVE) was achieved with the CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride/ethyl acetate [CH₃CH(OiBu)OCOCH₃/Et_1.5AlCl_1.5/CH₃COOEt] initiating system in toluene at 0 °C. The number‐average molecular weights (M_n's) of the obtained poly(2‐AdVE)s increased in direct proportion to monomer conversion and produced the polymers with narrow molecular weight distributions (MWDs) (M_w/M_n = ～1.1). When a second monomer feed was added to the almost polymerized reaction mixture, the added monomer was completely consumed and the M_n's of the polymers showed a direct increase against conversion of the added monomer. Block and statistical copolymerization of 2‐AdVE with n‐butyl vinyl ether (CH₂?CH? O? CH₂ CH₂CH₂CH₃; NBVE) were possible via living process based on the same initiating system to give the corresponding copolymers with narrow MWDs. Grass transition temperature (T_g) and thermal decomposition temperature (T_d) of the poly(2‐AdVE) (e.g., M_n = 22,000, M_w/M_n = 1.17) were 178 and 323 °C, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1629–1637, 2008     

Living cationic polymerization of cis- and trans-ethyl propenyl ethers and synthesis of block copolymers with isobutyl vinyl ether

The cationic polymerization of cis- and trans-ethyl propenyl ethers (EPE, CH₃? CH?CH? O? C₂H₅), initiated by a mixture of hydrogen iodide and iodine (HI/I₂ initiator) at ?40°C in nonpolar media (toluene and n-hexane), led to living polymers of controlled molecular weights and a narrow molecular weight distribution (MWD) (M?_w/M?_n = 1.2–1.3). The geometrical isomerism of the monomer did not affect the living character of the polymerization. ¹³C NMR stereochemical analysis of the polymers showed that the living propagating end is sterically less crowded than nonliving counterparts generated by conventional Lewis acids (e.g., BF₃OEt₂). New block copolymers between EPE (cis or trans) and isobutyl vinyl ether were also prepared by sequential living polymerization of the two monomers.     

Living cationic polymerization of vinyl ethers by electrophile/lewis acid initiating systems. XII. Phosphoric and phosphinic acids/zinc chloride initiating systems for isobutyl vinyl ether

Phosphoric and phosphinic acid derivatives (R¹R²PO₂H; R¹, R² = OPh, OPh; OnBu, OnBu; Ph, Ph; Ph, H) in conjunction with zinc chloride (ZnCl₂) led to living cationic polymerization of isobutyl vinyl ether (IBVE) in toluene below 0°C. The number-average molecular weights (M?_n) of the polymers (M?_n > 2 × 10⁴) were directly proportional to monomer conversion and in excellent agreement with the calculated values assuming that one polymer chain forms per R¹R²PO₂H molecule. Throughout the reaction, the molecular weight distributions (MWDs) stayed narrow (M?_w/M?_n ? 1.1). A dibasic acid, PhOP (O) (OH)₂, coupled with ZnCl₂, also induced living cationic polymerization of IBVE where one molecule of the acid generated two living polymer chains. The polymerization by (PhO)₂PO₂H/ZnCl₂ and its model reactions were directly analyzed by ³¹P and ¹H-NMR spectroscopy. The analysis showed that the acid initially forms the adduct [CH₃CH(OiBu)OP(O)(OPh)₂], the phosphate linkage of which is in turn activated by ZnCl₂ so as to initiate living propagation. The finding thus indicates that (PhO)₂PO₂H indeed acts as an initiator in the living polymerization. The NMR analysis also suggested that an exchange reaction occurs between the phosphate group at the polymer terminal and the chlorine in ZnCl₂. The occurrence of living IBVE polymerization with these various R¹R²PO₂H/ZnCl₂ systems shows that phosphoric and phosphinic acids are another general class of protonic acids which are effective initiators for the living cationic polymerization assisted by Lewis acids. © 1993 John Wiley & Sons, Inc.     

Living cationic polymerization of isobutyl vinyl ether by EtAlCl2 in the presence of ether additives: Cyclic ethers,cyclic formals,and acyclic ethers with oxyethylene units

The living cationic polymerization of isobutyl vinyl ether (IBVE) was investigated in the presence of various cyclic and acyclic ethers with 1-(isobutoxy)ethyl acetate [CH₃CH(OiBu)OCOCH₃, 1 ]/EtAlCl₂ initiating system in hexane at 0°C. In particular, the effect of the basicity and steric hindrance of the ethers on the living nature and the polymerization rate was studied. The polymerization in the presence of a wide variety of cyclic ethers [tetrahydrofuran (THF), tetrahydropyran (THP), oxepane, 1,4-dioxane] and cyclic formals (1,3-dioxolane, 1,3-dioxane) gave living polymers with a very narrow molecular weight distribution (MWD) (M?_ω/M?_n ≤ 1.1). On the other hand, propylene oxide and oxetane additives resulted in no polymerization, whereas 1,3,5-trioxane gave the nonliving polymer with a broader MWD. The polymerization rates were dependent on the number of oxygen and ring sizes, which were related to the basicity and the steric hindrance. The order of the apparent polymerization rates in the presence of cyclic ether and formal additives was as follows: nonadditive ～ 1,3,5-trioxane ? 1,3-dioxane > 1,3-dioxolane ? 1,4-dioxane ? THP > oxepane ? THF ? oxetane, propylene oxide ? 0. The polymerization in the presence of the cyclic formals was much faster than that of the cyclic ethers: for example, the apparent propagation rate constant k in the presence of 1,3-dioxolane was 10³ times larger than that in the presence of THF. Another series of experiments showed that acyclic ethers with oxyethylene units were effective as additives for the living polymerization with 1 /EtAlCl₂ initiating system in hexane at 0°C. The polymers obtained in the presence of ethylene glycol diethyl ether and diethylene glycol diethyle ether had very narrow molecular weight distribution (M?_ω/M?_n ≤ 1.1), and the M?_n was directly proportional to the monomer conversion. The polymerization behavior was quite different in the polymerization rates and the MWD of the obtained polymers from that in the presence of diethyl ether. These results suggested the polydentate-type interaction or the alternate interaction of two or three ether oxygens in oxyethylene units with the propagating carbocation, to permit the living polymerization of IBVE. © 1994 John Wiley & Sons, Inc.     

Lifetime of living polymers in cationic polymerization. III. Living polymerization of isobutyl vinyl ether initiated by a cationogen/etalcl2 system in the presence of 1,4-dioxane as an added base

The concentration ([P^*]) and lifetime (half-life) of the propagating species were measured in the living cationic polymerization of isobutyl vinyl either initiated by the 1-(isobutoxy) ethyl acetate [CH₃COOCH (OiBu) CH₃]/ethylaluminum dichloride (EtAlCl₂) system in the presence of excess 1,4-dioxane in n-hexane at 0 to +70°C; the acetate serves as a cationogen that forms an initiating vinyl ether-type carbocation. The measurements were based on the end-capping reaction with sodiomalonic ester [Na^⊕?CH (COOEt)₂], which was shown to react rapidly and quantitatively with the living growing end. From the terminal malonate group of the quenched polymers, [P^*] was determined by ¹H-NMR spectroscopy. In contrast to its constancy during the polymerization, [P^*] progressively decreased with time after the complete consumption of monomer. The postpolymerization decay was first order in [P^*], and the lifetime (half-life) of the living end was determined from the decay rate constant. The lifetime increased on lowering polymerization temperature, decreasing EtAlCl₂ concentration, and increasing dioxane concentration. In particular, the “base-stabilized” living ends, generated by the CH₃COOCH (OiBu) CH₃/EtAlCl₂/dioxane system, turned out extremely stable at 0°C (half-life > 5 days in the absence of monomer).     

Living cationic polymerization of vinyl ethers by electrophile/lewis acid initiating systems. VII. Living cationic polymerization of isobutyl vinyl ether by trimethylsilyl halide/zinc halide initiating systems in the presence of p-methoxybenzaldehyde: Effects of halide anions and zinc halides

Trimethylsilyl halides (Me₃SiY), in conjunction with zinc halides (ZnX₂) (Y and X:I, Br, Cl), were employed to investigate the living cationic polymerization of isobutyl vinyl ether (IBVE) in toluene at ?15°C in the presence of p-methoxybenzaldehyde; with the aldehyde and IBVE monomer, Me₃SiY yields an initiating species [Me₃Si? O? CHC₆H₄(OM_e) ? CH₂CH(OiBu) ? Y] that triggers the IBVE polymerization via the activation of its carbon-halogen bond (C? Y) by ZnX₂ into C^δ+…?Y^δ?…?ZnX₂. Living polymerizations occurred with the silyl iodide and bromide irrespective of the type of ZnX₂, either when Y = X (Me₃Sil/Znl₂ and Me₃SiBr/ZnBr₂) or when Y ≠ X (Me₃Sil/ZnBr₂, Me₃SiI/ZnCl₂, and Me₃SiBr/Znl₂). With these five initiating systems, the number-average molecular weights (M?_n) of the polymers increased in proportion to monomer conversion, and the molecular weight distributions (MWDs) of the polymers were narrow (M?_w/M?_n = 1.1?1.2). The Me₃SiCl-based systems (Me₃SiCl/ZnCl₂ and Me₃SiCl/Znl₂), in (Me₃SiCl/Znl₂), in contrast, failed to give perfectly living polymerization; the M?_n indeed increased with conversion, but the MWDs of the polymers were broader (M?_w/M?_n = 1.3?1.5). Thus, the living nature of the polymerizations with Me₃SiY/Znx₂ is primarily determined by the halogen Y in Me₃SiY, which generates the terminal carbon-halogen bond (C? Y) that is activated by ZnX₂ for the propagation via a species C^δ+…?Y^δ?…?ZnX₂. For Y^?, not only the iodide but the bromide anion also is suited for living cationic polymerization. The virtual absence of the effects of X in ZnX₂ implies that the halogen exchange between ZnX₂ and Y from Me₃ SiY at the growing end (C^λ+…?Y^δ?…?ZnX₂ ?C^δ+…?X^δ?…?ZnXY) is absent or negligible.     

Dispersion polymerization in polar solvents

The effect of the nitrogen purge, monomer purification, type of agitation, and presence of costabilizer on the particle size distribution (PSD) was investigated in the dispersion po-lymerization of styrene in ethanol and in the dispersion copolymerization of styrene and butyl acrylate in a water–ethanol mixture. Purging with nitrogen and, to a lesser extent, monomer purification, were of paramount importance to achieve monodispersity. The type of agitation had a week effect on the PSD, whereas the presence of costabilizer had no effect on the PSD. © 1995 John Wiley & Sons, Inc.     

Cationic polymerization of isobutyl vinyl ether initiated with transition‐metal ate complexes

The cationic polymerization of isobutyl vinyl ether was examined with transition‐metal ate complexes with trityl cation as initiators. The initiators were generated by the reaction of triphenylmethyl chloride [trityl chloride (TrCl)] with ate complexes of Nb, Mo, and W with lithium cation, which were obtained in situ by the reaction of the transition‐metal halides with anionic reagents (organolithium or lithium amide). When the polymerization was initiated with a mixture of TrCl and Li⁺[NbH₅(NnBuPh)]^?, the resulting poly(isobutyl vinyl ether)s had narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight = 1.13–1.20). Although the polymerization was supposed to be initiated by the electrophilic attack of the trityl cation, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of the resulting poly(isobutyl vinyl ether)s revealed the presence of H at the α‐chain end. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2636–2641, 2006     

Cationic polymerization of isobutyl vinyl ether coinitiated with heteropolyacid or its salts in aqueous medium

The suspension cationic polymerization of isobutyl vinyl ether (IBVE) in aqueous medium could be achieved by using H₃PW₁₂O₄₀, AlPW₁₂O₄₀, FePW₁₂O₄₀, K₃PW₁₂O₄₀, or Na₃PW₁₂O₄₀ as efficient water‐tolerant coinitiators in the presence of HCl. The addition reaction of IBVE with H₂O occurred to form IBVE–H₂O adduct and then subsequent decomposition immediately took place or turned to acetaldehyde diisobutyl acetal (A) in the presence of AlPW₁₂O₄₀, and ( A ) decomposed rapidly to form 2‐isobutanol ( B ) and acetaldehyde ( C ). Cationic polymerization of IBVE in aqueous medium was promoted greatly with increasing HCl concentration and proceeded extremely rapidly to get high polymer yield even at low concentration of AlPW₁₂O₄₀ of 0.3 mM. A sufficient amount of HCl was needed to decrease the hydrolysis of initiator IBVE–HCl and to accelerate the polymerization in aqueous medium simultaneously. The yield and molecular weight of poly(IBVE) increased with increasing concentrations of HCl and AlPW₁₂O₄₀ or with decreasing temperature. The isotactic‐rich poly(IBVE)s with m diad of around 60%, having M_n of 1200–4500 g mol^?1 and monomodal molecular weight distribution could be obtained via cationic polymerization of IBVE in aqueous medium. This is the first example of cationic polymerization of IBVE in aqueous medium coinitiated by heteropolyacid and its salts. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Living cationic polymerization of vinyl ether with a cyclic acetal group

The living cationic polymerization of 5‐ethyl‐2‐methyl‐5‐(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a vinyl ether with a cyclic acetal unit, was investigated with various initiating systems in toluene or methylene chloride at 0 to ?30 °C. With initiating systems such as hydrogen chloride (HCl)/zinc chloride (ZnCl₂), isobutyl vinyl ether–acetic acid adduct [CH₃CH(OiBu)OCOCH₃]/tin tetrabromide (SnBr₄)/di‐tert‐butylpyridine (DTBP), and CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride (Et_1.5AlCl_1.5)/ethyl acetate (CH₃COOEt), the number‐average molecular weights (M_n's) of the obtained poly( 1 )s increased in direct proportion to the monomer conversion and produced polymers with relatively narrow molecular weight distributions [MWDs; weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.2–1.3]. To investigate the living nature of the polymerization with CH₃CH(OiBu)OCOCH₃/SnBr₄/DTBP, a second monomer feed was added to the almost polymerized reaction mixture. The added monomer was completely consumed, and the M_n values of the polymers showed a direct increase against the conversion of the added monomer, indicating the formation of a long‐lived propagating species. The glass transition temperature and thermal decomposition temperature of poly( 1 ) (e.g., M_n = 13,600, M_w/M_n = 1.30) were 29 and 308 °C, respectively. The cyclic acetal group in the pendants of the polymer of 1 could be converted to the corresponding two hydroxy groups in a 65% yield by an acid‐catalyzed hydrolysis reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4855–4866, 2007