尼龙1010的拉伸结晶行为及Brill转变

摘要 :本文通过示差扫描热分析,广角X射线衍射分析及二维广角X射线散射等手段研究和讨论了尼龙1010在不同的拉伸比率(λ)及拉伸温度（Td）下拉伸诱导的晶体转变及结晶取向行为。实验表明,在拉伸条件下,尼龙1010易于从α晶型向δˊ晶型转变,而拉伸比率的提高,有利于促进这种Brill转变。而在相同的拉伸比率下,随着拉伸温度的提高,发现了尼龙1010从δˊ晶型向α晶型的独特转变,而这种过程刚好与无拉伸状态下的尼龙1010晶型和温度的相互关系截然相反。二维广角X射线散射实验研究结果表明尼龙1010的晶体取向度主要和拉伸比有关,并且（002）的晶面间距随着拉伸比率的提高而增大,表明了长轴尺寸的增大对拉伸取向的依赖关系。     

聚乙烯串晶在单轴拉伸形变过程中的微结构变化和机理

本文采用电子显微镜和小角Ｘ－射线散射（ＳＡＸＳ）技术研究了含有串晶结构（Ｓｈｉｓｈ—ｋｅｂａｂ）的高密度聚乙烯（ＨＤＰＥ）／超高分子量聚乙烯（ＵＨＭＷＰＥ）共混物高取向膜在单轴拉伸过程中的微结构变化．深入探讨了拉伸温度对聚乙烯在形变过程中微结构变化的影响．室温拉伸时，聚乙烯串晶结构主要发生了解结晶过程；高温（１１５℃）形变时，主要表现为折叠链片晶直接转变为伸展链纤维晶的应变诱导结晶过程．     

尼龙1010球晶的转化

本文利用偏光显微镜研究了尼龙1010球晶的转化。发现在降温过程中放射状球晶多转变成相同光性的环状球晶。升温时正环状转化为正放射状球晶;正、混合放射球晶部分转化为负放射状球晶;黄蓝两瓣球晶在一定温度范围内可与负放射球晶相互转变。多种球晶共存时,混合放射球晶可转变成两瓣、不对称四瓣和六瓣形放射球晶;正、混合坏状分别转变成不对称四瓣和六瓣形环状球晶;最后都以环状球晶熔化。     

聚(3-羟基丁酸酯-co-3-羟基戊酸酯)中β晶的形成与转变

本文通过同步辐射原位二维广角X射线(2D-WAXD)和原位红外光谱(FTIR)等手段，对聚(3-羟基丁酸酯-co-3-羟基戊酸酯)(PHBV)预取向膜二次拉伸过程及随后升温过程中的结构演化机制进行了系统研究。研究结果表明，二次拉伸过程中β晶的相对含量、取向程度和晶粒尺寸会随应变而升高；同时，体系的总α晶的取向度和晶粒尺寸变小，结晶度下降。这说明拉伸过程中，α晶会被破坏并转变为β晶。经过二次拉伸的PHBV膜，在升温过程中，α晶的取向、晶粒尺寸及总体结晶度会升高，而β晶的相对含量逐步下降到零。这说明在较高的温度下，β晶的分子链会重新排列，主要转变成了取向度高的α晶。β晶表现出从65℃到135℃的持续熔融转变。本研究初步阐释了PHBV薄膜中的β晶在拉伸和升温过程中的演化机制，为生物基聚酯薄膜的加工和性能调控提供了理论依据。     

基于同步辐射超小角X射线散射的高密度聚乙烯空洞化行为研究

以一系列高温结晶后自然冷却的高密度聚乙烯(HDPE)为研究对象,利用同步辐射超小角X射线散射(USAXS)和示差扫描量热技术(DSC)对样品的微观结构进行了分析,并在线研究了单轴拉伸过程中的空洞化行为.结果表明,结晶温度高于110℃后自然冷却到室温的样品中存在热稳定性不同的两组片晶,等温过程形成结构完善的厚片晶,而在冷却过程会形成有缺陷的薄片晶,两组片晶的熔点分别在133和110℃附近.在30℃拉伸时,所有样品都可观察到空洞化并伴随发白现象.并且,等温结晶中形成片晶厚度越大的样品,相应的空洞化现象越明显.在拉伸过程中,空洞出现在屈服点附近,其法向方向平行于拉伸方向,后随应变的增加发生转向,法向方向与拉伸方向垂直.样品中空穴的长度为900~1200 nm.另一方面,随着冷却过程生成薄片晶比例的增加,空洞化趋势下降.此外,提高拉伸温度,样品更倾向发生塑性形变,空洞化程度减弱.     

聚酰胺-6纤维拉伸特性的温度-速度换算

本文研究了拉伸温度、速度、高聚物晶型、低聚体及水分等因素对聚酰胺-6纤维拉伸特性的影响。认为纤维冷拉伸过程是结晶不完善部分——非晶区分子链段的运动;稍高于T_g温度拉伸,非晶区和晶区内不规整部分可能结晶;在更高温度拉伸明显地产生再结晶,其时主要是晶区的链段运动。低聚体的存在增加纤维的吸水量,这种增塑作用使聚酰胺-6纤维的T_g和再结晶温度大大下降。不同晶型对非晶区的制约作用不同因此有不同的拉伸特性。α晶型位能最低,结构稳定制约作用最强,较难拉伸;γ晶型位能较高,结构不稳定,较易拉伸且不易再结晶,生产纤维应当控制这种晶型以利于拉伸。应用时-温换算原理处理拉伸等温线与等速线结果得到总曲线;以T_g为参考温度并选择合理的常数得到W.L.F.方程如下: logα_T=-43.3(T_-T_g)/(374.8+T-T_g)利用总曲线可以很方便地力生产选择合理的拉伸工艺条件。     

聚对苯二甲酸乙二酯的结晶与取向

为了了解PET球晶的拉伸性能与球晶结构的关系以及无定形PET的取向和结晶,我们采取了两条不同的路线来制备样品:(1)先用溶液浇铸成膜的办法制备具有正球晶、负球晶或非常球晶的薄膜,然后进行单轴拉伸。电子显微图象及电子衍射证明,球晶的拉伸性能与C轴和球晶半径方向的夹角有关,夹角愈大拉伸愈困难;(2)先制备无定形的薄膜,然后在玻璃化温度附近进行单轴拉伸以获得C轴取向,再在215℃退火,使之结晶。电子衍射图证明,这样制备的样品具有高度的C轴取向。DSC结果表明,结晶的完善程度远比球晶的为高。     

尼龙1010环状球晶的研究

利用偏光显微镜研究了尼龙1010环状球晶的生成条件、形态特征和光学性质,发现在等温结晶过程中只可生成环状球晶;在降温过程中可由相同光性的放射状球晶转变成正、负、混合光性环状球晶;在升温过程中正光性和混合光性环状球晶分别转变成不对称四瓣形和六瓣形环状球晶,负放射球晶可转变成另一种负环状球晶。     

结晶聚合物的单轴拉伸和取向态结构 Ⅰ 拉伸结晶聚合物的形变机理

本文综述了关于拉伸结晶聚合物形变机理的研究工作,重点介绍了拉伸聚合物在形成细颈过程中,从原来的球晶(或堆积片晶)结构向纤维结构的转化过程,以及有关这一形变过程。目前存在的不同观点及各方面的实验证据。指出拉伸结晶聚合物的形变机理可能依赖于拉伸条件。     

取向对聚左旋乳酸/聚右旋乳酸复合物纤维结晶性能的影响

通过熔融纺丝的方法制备了PLLA/PDLA复合物初生纤维,在60℃拉伸获得高取向的牵伸纤维.采用X-ray散射为主要表征手段,结合差示扫描量热(DSC)、扫描电子显微镜(SEM)以及傅里叶变换红外光谱(FTIR)等技术,系统研究了不同初始结构的PLLA/PDLA复合物纤维在不同温度下的结晶行为,重点阐明了取向对PLA复合物纤维结晶结构的影响.结果表明,取向促进复合物纤维中立构晶的形成;将纤维升温至200℃停留3 min后,再进行降温,降温过程中,高度取向的牵伸纤维只有立构晶形成,而初生纤维则在150℃左右出现α晶,表明纤维中取向的立构晶会抑制α晶的形成.综合实验结果发现,通过低温牵伸初生纤维,然后高温(α晶熔点以上)退火,可制备出高取向且具有高立构晶含量的PLLA/PDLA复合物纤维.     

Oriented Nickel Nanonetworks and Their Submicron Fibres as a Basis for a Transparent Electrically Conductive Coating

The paper demonstrates a technique for applying an oriented nickel network to a glass surface. The method is based on the chemical reduction of nickel salt. The shaping and orientation of the resulting system are carried out using a micellar template of a surfactant and a magnetic field. Submicron nickel fibres are used to impart unity to the plurality of individual-oriented nickel nanonetworks. The result is a single conductive coating on the surface of the glass, which has a transparency in the optical range. Investigations of the structure, chemical composition, morphology and electrical conductivity of the coating were performed.     

Titanium Anodes with Active Coatings Based on Iridium Oxides: A Sublayer between the Active Coating and Titanium

An optimum composition and a technique for applying a protecting sublayer on titanium are substantiated experimentally. The sublayer prevents the oxidation of titanium during the production and application of highly porous metal oxide anodes. The formation of such a sublayer involves several stages: (a) coating chemically polished and etched in 5-% hydrofluoric acid titanium with hexachloroiridic acid, (b) drying hexachloroiridic acid, (c) a two-step treatment of anodes in argon with a low concentration of oxygen at 350°C, and (d) a brief annealing of the anodes in air at 400°C. The application of such a sublayer makes sense especially in the case of an anode with a thin highly porous active coating. The remarkable protecting properties of the sublayer are due to the formation of a dense coating on titanium. The coating consists of metallic iridium, titanium, and an amount of oxides of these metals. The titanium substrate itself undergoes minimum oxidation.     

Zur Reaktion von Dihydroxybiphenylen mit Phosphorpentachlorid ‐ Phosphepine mit Phosphonium‐ und Phosphoranstruktur

The 2, 2'‐dihydroxybiphenyl derivatives 1d‐f react with phosphorus pentachloride to give the dioxaphosphepinium hexachlorophosphates 3a, 3b , and 17 . The trichloro‐dioxaphosphepins 8a, 8b , and 21 were discussed as intermediates, which were obtained by chlorination of the 6‐chloro‐dioxaphosphepins 7a, 7b , and 20 . The hydrolysis of the dioxaphosphepins leads to the stable, cyclic phosphates 4a, 4b, 9a, 9b, 11a, 11b, 19a, and 19b . The crystal struc‐ture of 4a was determined; two different molecules was observed in the asymmetric unit.     

Characterisation of optical detectors using high-accuracy instruments

The facilities of the Metrology Research Institute at the Helsinki University of Technology, and methods for characterisation of optical detectors for spectral radiant intensity and irradiance responsivity, are described. The instrumentation for such characterisations includes a reference spectrometer with a number of auxiliary set-ups, and equipment for the spectral irradiance measurements with a filter radiometer based on a trap detector. The methods of realising the spectral responsivity scales based on an absolute cryogenic radiometer in house are addressed. The procedures and results of characterisation of a multipoint measuring system of photosynthetically active radiation, by employing the available facilities, are briefly described. The absolute irradiance responsivity of the device is determined by using a photometric lamp, whose spectral irradiance has been measured with the filter radiometer. The combined standard uncertainty of this set of calibrations is 3.6% at the 1σ level. The uncertainty is caused almost completely by the multipoint measuring system.     

A lubricated stagnation point flow of nanofluid with heat and mass transfer phenomenon: Significance to hydraulic systems

The improved thermal association of heat transfer is considerably observed due to interaction of nanoparticles in recent days. The lubrication phenomenon with heat and mass transfer effects plays a key role in the hydraulic systems. In current research, the thermal impact of nanofluid over a lubricated stretching surfaces near a stagnation point analytical has been studied. A thin layer of lubricating fluid with a variable thickness provides lubrication. The inspection of thermophoresis and Brownian motion phenomenon is illustrated via Boungrino model. The analytical finding of refurbished boundary layer ordinary differential equations is obtained by a reliable and proficient technique namely variational iteration method (VIM). The Lagrange Multiplier is a potent tool in proposed technique to reduce the computational work. In addition, a numerical comparison is presented to show the effectiveness of this study. The range of flow parameters is based on theoretical flow assumptions. Physical inspection of involved parameters on velocities, temperatures, concentrations, and other quantities of interest when lubrication is presented. The current results present applications in polymer process, manufacturing systems, heat transfer and hydraulic systems.     

Thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) as a nanoreactor of gold nanoparticles

The synthesis of a thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) (PGMA‐co‐PNIPAM) and its application as a nanoreactor of gold nanoparticles are studied. The thermoresponsive copolymer of PGMA‐co‐PNIPAM is first synthesized by the copolymerization of glycidyl methacrylate and N‐isopropylacrylamide using 2,2′‐azobis(isobutyronitrile) as an initiator in tetrahydrofuran at 70 °C and then crosslinked with diethylenetriamine to form a thermoresponsive hydrogel. The lower critical solution temperature (LCST) of the thermoresponsive hydrogel is about 50 °C. The hydrogel exists as 280‐nm spheres below the LCST. The diameter of the spherical hydrogel gradually decreases to a minimum constant of 113 nm when the temperature increases to 75 °C. The hydrogel can act as a nanoreactor of gold nanoparticles because of the coordination of nitrogen atoms of the crosslinker with gold ions, on which a hydrogel/gold nanocomposite is synthesized. The LCST of the resultant hydrogel/gold nanocomposite is similar to that of the hydrogel. The size of the resultant gold nanoparticles is about 15 nm. The hydrogel/gold nanocomposite can act as a smart and recyclable catalyst. At a temperature below the LCST, the thermoresponsive nanocomposite is a homogeneous and efficient catalyst, whereas at a temperature above the LCST, it becomes a heterogeneous one, and its catalytic activity greatly decreases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2812–2819, 2007     

生物质三组分热裂解行为的对比研究

在热天平上对比研究了生物质中的纤维素、半纤维素和木质素三种主要组分的热失重规律。结果表明，作为半纤维素模型化合物的木聚糖热稳定性差，在217℃～390℃发生明显分解；纤维素热裂解起始温度最高，且主要失重发生在较窄温度区域，固体残留物仅为6.5%；木质素表现出较宽的失重温度区域，最终固体残留物高达42%。在红外辐射机理试验台上对比研究了三组分热裂解产物随温度的变化规律。三组分热裂解生物油产量随温度变化先升后降。纤维素生物油产量在峰值上最高，但纤维素生物油热稳定性差，高温时挥发分的二次分解最明显；木聚糖和木质素生物油产量较低，表现出较好的热稳定性。三组分热裂解焦炭产量随温度升高而降低，最终纤维素热裂解焦炭产量为1.5%，而木聚糖和木质素分别为22%和26%。三组分热裂解气体产物随温度升高而增长，但在气体组成分布上因三组分的结构上的差异而不同。     

Fabrication of a Simple and Cheap Screen-printed Silver/Silver Chloride (Ag/AgCl) Quasi-reference Electrode

In this work, a silver/silver chloride ink is fabricated using two steps. First the silver ink is prepare using silver, nail polish and acetone. Then the silver ink is painted in a paper substrate and a silver chloride layer is deposited using a bleach solution. The result is the silver/silver chloride conductive ink. The silver ink is cheap ($2.49/g), well-dispersive and very easy to fabricate. The materials were characterized by SEM and XRD. The Ag ink showed the formation of a continuous network throughout the silver ink film with fewer agglomeration. The effective chlorination process was also observed in the Ag/AgCl characterization. Since the Ag/AgCl substrate will be used as a quasi-reference electrode, it is important to investigate the electrical properties. The Ag ink showed an average ohmic resistance of 2.27 Ω. The addition of the AgCl layer decreases the conductivity, as expected. In summary, the Ag/Ag/Cl ink developed is simple, well-dispersed, cheap and with good conductivity. Therefore, it can be used as a conductive ink in the fabrication of quasi-reference electrodes.     

Development of Enzyme Conductometric Biosensor for Dopamine Determination in Aqueous Samples

Dopamine is a biologically active chemical that performs a number of vital functions as a hormone and neurotransmitter. Therefore, the determination of dopamine concentration in the human body is important for biomedical research. The content of dopamine in the blood varies depending on the age of a healthy person and can serve as a prognostic marker of many diseases. The aim of this work was to develop a new enzyme conductometric biosensor for the determination of dopamine in aqueous samples and to study the biosensor's analytical characteristics. The conductometric method of analysis with differential measurement mode was used in the work. Two pairs of gold interdigitated electrodes deposited on a sitall substrate were used as a conductometric transducer. The biorecognition element of the biosensor was based on laccase immobilized by glutaraldehyde cross-linking. The optimal conditions of laccase immobilization were selected. The influence of solution parameters (ionic strength, pH, buffer capacity) on the biosensor work was investigated. The biosensors demonstrated high sensitivity to dopamine (minimum limit of detection −7.8 μM) with the linear range up to 1 mM. The biosensor was highly selective and reusable. The proposed biosensor was tested regarding the possibility of its long-term storage under different conditions. The developed conductometric biosensor was proven to be suitable for measuring dopamine concentration in biological and pharmaceutical samples.     

ZSM-5／Silicalite-1核壳分子筛含氟水热体系的合成及表征

以圆柱形ZSM-5为核,用柠檬酸对其外表面进行预处理后,在含氟壳层晶化体系中二次生长合成核壳分子筛.通过X射线衍射、扫描电镜、透射电镜、N2吸附及氨程序升温脱附对分子筛进行了表征,并以甲苯歧化和1,3,5-三甲苯裂化为探针反应对分子筛性能进行了考察.结果显示,产物是以ZSM-5为核、silicalite-1纳米晶为壳的两相复合微孔分子筛材料;在含氟体系中ZSM-5外延生长出了致密壳层;全硅壳层的覆盖度约达到97%,核壳分子筛的外表面酸位随之减少,但基本保持孔道内的酸性。