Comparison of responses of CR-39, PM-355, and CN track detectors to energetic hydrogen-, helium-, nitrogen-, and oxygen-ions

Samples made of the CR-39 and PM-355 plastic nuclear track detectors (NTDs) as well as of the CN films were irradiated with quasi-monoenergetic beams of protons, alphas, N⁺-, and O⁺-ions produced by various accelerators. For different samples an energy value of the particle beams was changed from several hundreds keV to 3 or 4.5 MeV. After irradiation the detector samples were etched chemically under controlled conditions during periods lasting from 2 hrs to 20 hrs. Every 2 hrs track diameters were measured by means of an optical microscope. Differences in the crater diameters in the detectors etched in steps, and those etched continously, have been found to be smaller than 10 percent. The paper results detailed calibration diagrams showing a dependence of track diameters on the ion energy value for different etching times.     

A photometry method for measuring tracks density on SSNTDs

The purpose of this work is to determine alpha track density on solid state nuclear track detectors (SSNTDs) such as CR-39 efficiently with minimal time. Samples of CR-39 were irradiated with different doses from an alpha emitter. These samples were chemically etched and the tracks counted using an optical microscope. The intensity of the transmitted light (λ=400–1200 nm) through irradiated and etched CR-39 was measured using a photomultiplier. For all wavelengths used in this study, it is found that the transmittance of light decreases as irradiation time increases. In addition, the calibration factor was calculated from the relation between track density on CR-39 and light transmittance. The procedure appeared to be a good and fast technique for determining radon concentration in the environment and consequently dose reading.     

Comparison of responses of LR-115A, CR-39 and PM-355 track detectors to pulsed low-energy proton streams

The paper concerns applications of LR-115A, CR-39 and PM-355 solid-state nuclear-track detectors (SSNTDs) for investigation of pulsed fluxes of protons below 300 keV. The proton streams were generated by the RPI-IBIS device operated with hydrogen puffing [Baranowski et al. 2000. Studies of hydrogen discharges in RPI-type devices with different electrode configurations. Czech. J. Phys. 50 (Suppl. S3), 101–107]. To perform ion mass- and energy-analysis, a Thomson mass-spectrometer equipped with a special input system and exchangeable detectors was used. A quantitative analysis of proton tracks upon Thomson parabolas was performed by means of an optical microscope equipped with a CCD camera. It made possible to measure proton tracks and to determine their statistics. The paper presents proton energy spectra recorded with the selected detectors, and responses of these detectors to protons of energy from about 30 to 300 keV. The results are important for verification of detector characteristics and for measurements of protons at different experimental conditions.     

Watching at the correlation between the specific track-etch rate and the primary physical parameters of the swift ion interaction with the CR-39

Analysis of etched nuclear tracks in CR-39 solid state nuclear track detectors has recently been made possible by the confocal microscope. This recent innovation has opened up some particularly interesting perspectives. The main originality of this microscopy technique is that it makes it possible to work on numerical, three-dimensional images of chemically etched nuclear tracks in the CR-39. We have studied the performances of this new approach for light ions (H, He, Li and C) with kinetic energies typically of the order of the MeV per nucleus. First, we determined the response functions of the CR-39 for these ions. We were then able to show that aside from decreasing the analysis time of traditional methods, the confocal microscope greatly increases the sensibility of the detection. The aim of this study was to find a correlation between the response functions and the primary physical parameters of the interaction between the ion and the material, such as the linear energy transfer (LET), the restricted energy transfer (REL_ω0), the integrated radial dose or the rate of ionization. Although these parameters presented a strong resemblance to the experimental response functions (they are all “Bragg” curves), none of them were correlated to the response function in an unambiguous way.     

Relativistic Energy Pb Projectile Fragmentation with Heavy Target Nuclei

We investigate the fragmentation of 158A GeV ^207Tpb projectiles with Bi, Pb, Cu and AI targets using CR-39 nuclear track detectors. The exposures were made at SPS-CERN. After the etching, the detectors were scanned using an optical microscope to collect the data of etched cone diameters and lengths. We measured the partial charge-changing cross sections using the data of etched cone lengths. The predicted cross sections are compared to similar measurements reported in literature and their dependences on projectile and target mass are described.     

A CR-39 based thermal neutron dosimeter

Both chemically and electrochemically etched CR-39 detectors are used for the detection of fast neutrons. In practical situations, fast neutrons are always accompanied by thermal neutrons. Therefore, the response of the CR-39 based dosimeter has to be extended to thermal neutrons. To do so, a radiator/converter like LiF is introduced in front of the CR-39 detector and an optimum thickness of the LiF film is determined so that a response similar to that of the fast neutrons is achieved. Thin films of natural LiF were prepared and the response of the CR-39 detector was studied as a function of the film thickness.     

Triton and alpha-particle contribution from LiF converter for neutron dosimeter

A personnel neutron dosimeter prototype based on chemical and electrochemical etched CR-39 detector, combined with LiF converter, has been calibrated using an ICRP-like phantom, under a heavy-water moderated Californium source neutron spectra; A conversion factor of 1.052±126 spots cm⁻² mSv⁻¹ was obtained. The sealing properties of the detector holder showed a ten-fold reduction in radon background when it was tested in a high radon atmosphere. A convenient mechanical shock resistance was achieved in LiF converters by sintering to 11 tons pressure LiF powder at 650°C, during one hour.     

Characteristics of diallyl phthalate resin as a fission track detector

Diallyl phthalate (DAP) resin plates were irradiated with fission fragments, and then etched in aqueous solution of KOH. Etched tracks were observed and counted by using an optical microscope. The detection efficiency of fission fragments was about 100% for both perpendicular and random incidence. DAP plates were insensitive to alpha particles and fast neutrons. These characteristics are suitable for detecting selected fission fragments, which coexist with alpha particles or fast neutrons. DAP plates are valuable for quantitative analysis of fissionable materials and neutron dosimetry. DAP and allyl diglycol carbonate (CR-39) were formed into copolymers in various ratios. The copolymers showed intermediate characteristics between DAP and CR-39. The fabrication of the copolymers made it possible to control the discrimination level for detection of heavy charged particles.     

Application of quartz glass tubes as the track detectors for chemical identification of short-lived isotopes of elements 104, 105 and 106

The quartz glass open chromatographic columns with thermal gradient, which usually were used for the investigation of chemical properties of short-lived Z104 nuclides, were first used as the track detectors of spontaneously fissioning isotopes of elements 104, 105 and 106. The recoil nuclei of these elements were captured by the flow of gaseous chlorides then go to the quartz tube with reducing thermal gradient 400°C-100°C. The quartz tube was etched in 40% HF. The tracks due to spontaneous fission of isotopes ²⁵⁹104, ²⁶²105 and ²⁶³106 which were etched at the internal wall of quartz tubes were counted under optical microscope.     

Track measurements of fast particle streams in pulsed discharge explosive plasma

This paper reports results of track registration for fast particles from the hot spot sparked inside a metal target. CR-39 track detectors placed in the ion pinhole camera, a magnetic analyzer, and Thomson-type mass-spectrometer in order were used to obtain images of the hot spot and to determine spectra of the fast particles. Using track detectors in the pinhole camera, we have obtained specific split images. The “average etch rate ratio versus track length” locus for track sample groups is depicted by means of squared diameters asymptotic method. Our analysis shows the majority of tracks belong to hydrogen nuclei. The track loci for the detectors from the pinhole or analyzers turn out to be split into two parallel streaks that have been interpreted as a proton–deuteron doublet. Data obtained using the Thomson analyzer clearly demonstrate the equal numbers of protons and deuterons for some parallel parabola sections.     

Beam profile measurement with CR-39 track detector for low-energy ions

A CR-39 track detector was successfully used to measure the outline of thin low-energy ion beams. After the etching, the surface of the detector was examined with an observation system composed of a Normarski microscope, a CCD camera and a digital image processing computer. Beam images obtained with the system were in good agreement on the outline of the beam formed with a beam aperture. Also, the resolving power in the beam outline measurement was roughly explained from the consideration of the ion range and the etch-pit growth in the chemical etching for the CR-39 detector.     

Registration temperature effect on sensitivity of CR-39(DOP) and SR-90 polymer track detectors

The samples of CR-39(DOP) and SR-90 polymer track detectors have been exposed to -particles from ²⁴¹Am source in an exposure unit. The temperature of the detectors during irradiation has been varied from −30°C to 70°C. These exposed samples have been etched in 6.25 N NaOH solution at 60°C for various etching times. The variation of sensitivity of these detectors as a function of registration temperature has been studied. It has been observed that at the fixed registration temperature, the sensitivity of SR-90 is more than CR-39(DOP) polymer track detector. However, the enhancement in sensitivity with the decrease in registration temperature is more pronounced in case of CR-39(DOP) than SR-90.     

Sensitization of polymeric track detectors with carbon dioxide

The effect of CO₂ on the sensitivity of polymeric track detectors was studied. It has been found that the sensitivity of SR-90 is dependent on the amount of CO₂ dissolved in the polymer at the time of etching. It has been also found that CR-39 can be sensitized to some extent with an aging in CO₂. Since the sensitization in CO₂ is possible even a long time after the irradiation, the mechanism of the latent track formation by CO₂ is quite different from that by O₂. This would be the key to achieve the long term stability of polymeric track detectors such as SR-90 and CR-39.     

Measurements of radon concentration in soil gas by CR-39 detectors

A miniature diffusion chamber with a 25 × 4 × 0.5 mm CR-39 track etch detector (Pershore Moulding Ltd.), mounted on the 1.1 m long pole has been developed for radon gas measurements at 1 meter depth in the soil. For chemically etched CR-39 (7h, 70°C NaOH) and automatic track analysis the lowest detection limit of the chamber was found to be 0.5 MBq h m⁻³ and the useful exposure range from 2 to 20 MBq h m⁻³. The typical exposure time in the soil is between 2 to 14 days. The chamber was tested against the active AlphaGUARD PQ-2000 (Genitron Instruments GmbH) probe. The test yielded consistent results for soils with typical values of permeability and which are not miniature with water. The pilot measurements of radon gas in soil conducted with the miniature diffusion chambers around 48 buildings in Kraków and Silesia regions yielded an average radon concentration of 13 kBq m⁻³. The chambers are to be applied to measure radon concentration in soil before constructing new houses in order to avoid high radon risk areas.     

Angular and dose dependence of CR-39 neutron response for shape-selected tracks

A shape selection method corresponding to an energy discrimination was used to eliminate unwanted events disturbing evaluation of CR-39 detectors in detecting tracks induced by particles both of perpendicular and oblique incidence. The angular dependence of the response was examined, detecting fast neutrons from ²⁵²Cf with shape selection technique at various angles and distances. Also, the CR-39 track detectors with the ²⁵²Cf source were exposed to high γ-intensity of a ⁶⁰Co irradiation facility in the range 0.1 to 4.5 kGy, similar to the exposures inside spent fuel assemblies. Using the two functions the lower limit of burnup could be determined by the method.     

Estimation of the latent track size of CR-39 using atomic force microscope

As a frame work of the study for the latent track size measurement using atomic force microscope, we have measured the minute etch pits and the extremely small amount of bulk etch of CR-39 at the beginning of chemical etching, and obtained its growth curves in nanometer dimensions. The pieces of CR-39 were exposed to 6 MeV/nC and Fe ions with normal incidence angle and were etched in 70°C 7 N NaOH solution for 0.5,1,2,3,5 min. The diameters of latent track were estimated to be 17 nm for Fe ions and 8 nm for C ions, respectively. These values are comparable to the experimental data on the average ‘track core diameters’ that have been obtained by various experimental techniques.     

Optimization of CR-39 for fast neutron dosimetry applications

We present the results of an experimental work aimed at improving the performances of the CR-39^® (Registered Trademark of PPG Industries Inc.) nuclear track detector for neutron dosimetry applications. The work was done in collaboration with the Intercast Europe S.p.A., producer of CR-39 for commercial and scientific applications. We compare the CR-39 made with different additives concentrations and different polymerization processes. We evaluate the response of the CR-39 to fast neutrons from three sources: ²⁴¹Am---Be, ²⁵²Cf and ²³⁸Pu---Li. Particular attention was paid to background fluctuations that limit the lower detectable dose.     

The determination of the neutron component of cosmic radiation fields in spacecraft

Poly allyl diglycol carbonate (PADC or CR-39^®) etched track detectors may be used to estimate the neutron component of the cosmic radiation in spacecraft using simple techniques developed for neutron personal dosimetry. Electrochemically etched pits are identified and counted using fully automated read-out procedures. The neutron component of the radiation field at the location of the dosimeter will produce electrochemically etchable tracks, as will the proton and energetic heavy charged particle components, depending on particle type, energy and angle of incidence. The response to incident charged particles which produce tracks and are counted as if produced by a neutron, will lead to an over-estimate of the neutron component. A correction can be applied to take account of this, or an additional chemical etch carried out which allows discrimination. Recent results for exposures in low-Earth orbit are reported.     

Effect of Transferred Electronic Energy Density on Optical,Electrical and Structural Properties of Polyallyl-Diglycol Carbonate (CR-39) Polymer

Commercially available polyallyl-diglycol carbonate (CR-39) track detectors have attracted wide interest in many fields of science and technology. This is because of their low cost, relatively easy handling, and being more similar to human tissue than other passive detectors. After the Fukushima accident, there was a need to study the impact of the released alpha particles from radionuclides. In this study, CR-39 polymers were irradiated with α-particles with different linear energy transfers 11.11, 19.70, and 28.77 eV/Å, at fluences of 49,490/cm² and 2,482,763/cm². The modifications in the optical, electrical, and structural properties induced by the radiation were measured. The results showed that low values of transferred electronic energy density along the alpha particle tracks led to a slight increase in the optical band gap energy and a small reduction in the conductivity. The amorphous nature of the CR-39 samples was not affected by the changes of the transferred electronic energy density.     

Application of the ray tracing method in studying tracks in SSNTDs

The ray tracing method was applied to study etched tracks from α-particles in CR-39 solid-state nuclear track detectors. The transmission mode of a microscope operation was simulated. A track was considered as a set of small triangular elements, and the brightness of all elements was calculated systematically through the entire track to create the final image. Preliminary results are given for α-particle tracks in the CR-39 detector for initial energies of 4 and 4.5 MeV, and incident angles of 40 and 90°, respectively. Total reflection, as well as the slope of a surface element in the track wall, were identified as the main factors that affect the brightness of that element. At this stage, comparisons with experimental results can be made in terms of the average grey levels for the entire tracks.