铁掺杂TiO2纳米管阵列对不锈钢的光生阴极保护

在含FeSO4的HF、H2SO4/HF、NaF/Na2SO4溶液中,通过电化学阳极氧化直接在纯钛表面制备Fe 掺杂的TiO2(Fe-TiO2)纳米管阵列. 应用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见吸收光谱(UV-Vis)、X 射线光电子能谱(XPS)等手段对纳米管阵列的结构、形貌及化学组成进行表征. 利用光电化学测量研究Fe-TiO2纳米管阵列在不同波长范围内的光电响应特性和光生阴极保护行为. 考察了温度、时间、掺杂含量等参数对TiO2纳米管阵列的几何尺寸、形貌和光电性能的影响. 结果表明, Fe掺杂可有效减缓TiO2纳米管阵列载流子的复合, 窄化TiO2带隙宽度, Fe-TiO2在410-650 nm范围显示强吸收, 并使光谱响应扩展到波长大于400 nm 的可见光区. 实验结果还表明, Fe-TiO2纳米管阵列对316不锈钢(316L)具有良好的光生阴极保护作用, 暗态下阴极保护作用可继续维持.     

TiO_2纳米管阵列的制备及其对316不锈钢光生阴极保护作用的研究

应用直接电化学阳极氧化法,于含氟电解液中,在纯钛表面制备一层整齐有序的TiO2纳米管阵列.扫描电子显微镜(SEM),X射线衍射(XRD)表征该纳米管阵列的形貌及晶体结构,光电化学联用系统研究其光电响应特性及对316L的光生阴极保护作用.结果表明:以TiO2纳米管阵列膜作为光生阳极时,在紫外光区(λ<387nm)有显著增强的光生电流响应,并对316不锈钢有较好的光生阴极保护作用.暗态下,光生电极电位仍可维持较长的一段时间,继续起到阴极保护作用.     

氧化钛纳米管阵列制备及形成机理

采用电化学阳极氧化法在HF水溶液体系使纯钛表面形成一层结构规整有序的高密度TiO2纳米管阵列,考察了几种主要的实验参数（阳极氧化电压、温度、时间、电解液浓度）对TiO2纳米管阵列形貌和尺寸的影响.结果表明,阳极氧化电压是影响氧化钛形貌和纳米管尺寸的最主要因素,而温度和电解液浓度只影响TiO2纳米管阵列形成的时间.对TiO2纳米管阵列进行X射线衍射（XRD）和扫描电子显微镜（SEM）的分析,初步表征了TiO2纳米管阵列的电学性质.并讨论了TiO2纳米管的形成机理.     

High sensitive matrix-free mass spectrometry analysis of peptides using silicon nanowires-based digital microfluidic device

We present for the first time an electrowetting on dielectric (EWOD) microfluidic system coupled to a surface-assisted laser desorption-ionization (SALDI) silicon nanowire-based interface for mass spectrometry (MS) analysis of small biomolecules. Here, the transfer of analytes has been achieved on specific locations on the SALDI interface followed by their subsequent mass spectrometry analysis without the use of an organic matrix. To achieve this purpose, a device comprising a digital microfluidic system and a patterned superhydrophobic/superhydrophilic silicon nanowire interface was developed. The digital microfluidic system serves for the displacement of the droplets containing analytes, via an electrowetting actuation, inside the superhydrophilic patterns. The nanostructured silicon interface acts as an inorganic target for matrix-free laser desorption-ionization mass spectrometry analysis of the dried analytes. The proposed device can be easily used to realize several basic operations of a Lab-on-Chip such as analyte displacement and rinsing prior to MS analysis. We have demonstrated that the analysis of low molecular weight compounds (700 m/z) can be achieved with a very high sensitivity (down to 10 fmol μL(-1)).     

Titanium dioxide anatase as matrix for matrix-assisted laser desorption/ionization analysis of small molecules

The use of inorganic species as assisting materials in matrix-assisted laser desorption/ionization (MALDI) analysis is an alternative approach to avoid interfering matrix ions in the low-mass region of the mass spectra. Reports of the application of inorganic species as matrices in MALDI analysis of small molecules are, however, scarce. Nevertheless, titanium dioxide (TiO(2)) powder has been reported to be a promising matrix medium. In this study we further explore the use of TiO(2) as a matrix for the MALDI analysis of low molecular weight compounds. We present results showing that nanosized TiO(2) anatase and TiO(2) rutile perform better as MALDI matrices than a commercial TiO(2) anatase/rutile mixture. Moreover, when using nanosized TiO(2) anatase as a matrix, high-quality mass spectra can be obtained with strong analyte signals and weak or non-existing matrix interference ions. Furthermore, our results show that the phase type plays an important role in the application of TiO(2) as a MALDI matrix.     

聚甲基丙烯酸甲酯固定化碳纳米管作为MALDI基质的研究

将聚甲基丙烯酸甲酯材料在多壁碳纳米管表面原位聚合, 利用这种修饰的碳纳米管作为基质辅助激光解析离子化(MALDI)的基质, 利用修饰后的碳纳米管可以“溶解”的特性实现了稳定的MALDI离子化, 并且消除了在低质量端的基质噪音. 此类聚合物衍生的碳纳米管具有相对较好的亲水性表面, 可“溶解”在溶剂中. 此方法适用于有机小分子、多肽、聚合物和蛋白质酶解肽段的质谱分析. 实验表明聚甲基丙烯酸甲酯固定化碳纳米管能有效地吸收和传递激光能量, 可与样品充分地分散混合, 质谱检测背景低, 重现性好, 具有较宽的可测质量范围. 此方法在小分子快速检测和蛋白质组学方面有很大的应用前景.     

Preparation of High-Orderly TiO2 Nanotubes in Organic Solution and Characterization of C-doped TiO2

"High-orderly TiO2 nanotube arrays were fabricated by anodic oxidation of pure titanium substrate in organic electrolyte containing fluoride. Different morphological nanotubes of titania were obtained through controlling the different anodization voltages and durations. The length of the longest nanotubes was approximately 60 1m and the length-to-width aspect ratio was about 600. The nanotube layers were then annealed at different temperatures (450, 550, and 650 oC) in air for 2 h. The samples were characterized by scanning electron microscopy, X-ray diffraction (XRD), energy dispersive X-Ray (EDS) and UV-Vis spectrometer. The XRD results demonstrated that the as-anodized samples were amorphous and the structure changed to antanse and rutile when the samples were annealed at higher temperature. The EDS microanalysis indicated the presence of carbon in the TiO2 nanotubes. The result of degradation of methylene blue showed clearly that the photocatalytic activity of C-doped TiO2 nanotubes increased by 10%."     

Immobilized carbon nanotubes as matrix for MALDI-TOF-MS analysis: Applications to neutral small carbohydrates

In this work, we reported on the advantages of immobilized carbon nanotubes as a novel MALDI-matrix. Recently, carbon nanotubes have been reported to be an effective MALDI matrix for small molecules (Anal. Chem.2003, 75, 6191), as it can eliminate the interfering matrix peaks as well as form a web morphology to fully disperse the analyte and allow strong ultraviolet absorption for enhanced pulsed laser desorption and ionization. In our study, to overcome the problem that the carbon nanotube matrix may fly off from the target, a type of polyurethane adhesive, NIPPOLAN-DC-205, is introduced to immobilize carbon nanotubes on the target, which enables widespread application of carbon nanotubes as matrix for MALDI-MS analysis. At the same time, the properties of the carbon nanotubes as an efficient matrix remained after immobilization. The presence of NIPPOLAN-DC-205 increases the time for analysis at a particular desorption spot by minimizing the time-consuming search for "hot spots" and facilitating experiments such as post source decay (PSD) which need longer-lasting signals. Moreover, NIPPOLAN-DC-205 produces no interference peaks and can easily be cleaned with acetone. Fast evaporation technology may be used to enhance signal reproducibility in MALDI analysis using carbon nanotubes as matrix. Consequently, the applicability of the carbon nanotube as matrix for matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) analysis of low molecular mass analytes is highly improved. The feasibility of the method employing polyurethane is demonstrated by comparison of the results produced from the carbon nanotube matrix with and without immobilization. In addition, neutral small carbohydrates, which are difficult to be ionized normally, can be cationized with high efficiency by MALDI-TOF-MS using the immobilized carbon nanotube matrix. The method was further applied to analyze peptides and detect urine glucose successfully.     

Surface-assisted laser desorption/ionization mass spectrometry on titania nanotube arrays

Titania nanotube arrays (NTA) generated from anodizing processes are tested as the substrate for surface-assisted laser desorption/ionization mass spectrometry (SALDI MS). The background generated from titania NTA is very low, making the approach suitable for the analysis of small molecules. The upper detectable mass is approximately 29 kDa. Homogeneous sample deposition leads to good shot-to-shot reproducibility and suitability for quantitative analysis. Additionally, phosphopeptides can be selectively trapped on the titania NTA substrate, as illustrated by simply depositing a tryptic digest of beta-casein followed by titania NTA SALDI MS analysis. The detection limit for small organics and peptides is in low fmol.     

Hierarchically branched titania nanotubes with tailored diameters and branch numbers

Over the past decade, electrochemical anodization of self-organized TiO(2) nanotubes has been studied intensively with the main focus being on uniform diameters along the TiO(2) nanotube depth direction. In the present work, hierarchically branched TiO(2) nanotubes with tailored diameters and branch numbers are successfully achieved by adjusting the anodization voltage. Reducing the applied voltage by a factor of 1/√n causes a one trunk nanotube to diverge into n-branched TiO(2) nanotubes, whose diameters are 1/√n of the trunk nanotube diameter (n is an integer). Multiple layers of branched TiO(2) nanotubes are also obtained by further dividing the branched nanotubes when the applied voltage is further reduced step-by-step with a 1/√n factor. Enlargement and termination of TiO(2) nanotubes occur when the anodization voltage increases by √n times. Alternating increase and decrease in the applied voltage lead to a more sophisticated hierarchical structure of TiO(2) nanotubes. The fundamental understanding of these processes is discussed.     

二氧化钛纳米管储氢能力的分子动力学研究

二氧化钛纳米管是一种有前景的储氢材料,因此,在本文中通过卷曲锐钛矿单分子层,获得锯齿型(Zig-zag)和手性型(Chiral)二氧化钛纳米管结构。并采用分子动力学方法(Molecular dynamics)研究了氢分子分别在锯齿型和手性型二氧化钛纳米管和碳纳米管中的分布情况,并计算其储氢能力。结果表明,与碳纳米管一样,锯齿型和手性型二氧化钛纳米管存在管间储氢和管内储氢情况,并且氢分子在管间和管内的分布与二氧化钛纳米管内、外两侧的氧原子相关。Lennard-Jones势能模型表明:氢分子向纳米管内部和管间隙处的低能处聚集,形成氢分子环结构。储氢量计算结果表明,虽然锯齿型和手性型二氧化钛纳米管储存的氢分子数目较多,但由于系统重量较大,储氢量较低,低于美国能源部6%的商业标准,不能满足实际需要,而碳纳米管储氢量接近这一标准。     

TiO2-MoO3复合纳米管阵列薄膜的制备及其可见光活性

通过阳极氧化的方法制备TiO₂纳米管薄膜, 在MoO₃存在的条件下对该薄膜进行热处理得到TiO₂-MoO₃复合纳米管阵列薄膜. 利用X射线衍射(XRD), 扫描电子显微镜(SEM), X射线光电子能谱(XPS), 电化学阻抗谱(EIS), Mott-Schottky 及光电化学方法对得到的薄膜进行了表征. XRD结果表明, TiO₂-MoO₃复合纳米管薄膜中的TiO₂主要为锐钛矿晶型. SEM实验证实了薄膜纳米管结构的存在, 样品中的MoO₃均匀地分散在TiO₂纳米管表面. 利用XPS方法分析了TiO₂-MoO₃复合纳米管薄膜元素的组成, 结果表明, MoO₃在TiO₂表面形成TiO₂-MoO₃复合纳米管薄膜. 研究了热处理温度以及热处理时间对样品的光电化学性能的影响, 相对于单纯TiO₂纳米管薄膜, 适量引入MoO₃提高了样品在可见光区的光电响应能力, 样品的平带电位负移. 在450 °C热处理60 min制得的TiO₂-MoO₃复合半导体纳米管阵列薄膜光电响应活性最高.     

In vitro corrosion study of different TiO2 nanotube layers on titanium in solution with serum proteins

Titanium oxide nanotubes prepared by anodization have received considerable attention in the biomaterials domain. The objective of this study was to demonstrate the electrochemical behavior of different diameter TiO(2) nanotube layers on titanium in phosphate buffered saline (PBS) and Dulbecco's minimum essential medium+10% fetal calf serum (D-FCS) using open circuit potentials (OCP), electrical impedance spectroscopy (EIS), and a potentiodynamic polarization test. The results showed that the nanotubes had higher OCP, higher resistance of the inter barrier layer (R(b)), and lower I(pass) in the two test solutions compared to the smooth Ti, especially the 30 nm diameter nanotubes. The corrosion resistance of the nanotubes in D-FCS was higher than in PBS because of protein adsorption from the D-FCS solution as suggested by scanning electron microscope (SEM) images. In addition, protein aggregates of 30 nm diameter nanotubes caused the model of EIS spectra to transform from two-layer to three-layer. The corrosion behavior of the nanotubes for use as a dental implant material is discussed.     

A novel strategy for MALDI-TOF MS analysis of small molecules

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) does not work efficiently on small molecules (usually with molecular weight below 500 Da) because of the interference of matrix-related peaks in low m/z region. The previous methods developed for this problem focused on reducing the peaks caused by the traditional matrices. Here, we report a novel strategy to analyze small molecules in a high and interference-free mass range by using metal-phthalocyanines (MPcs) as matrices which should be capable of forming matrix-analyte adducts. The mass of the target analyte was calculated by subtracting the mass of MPc from the mass of the MPc-analyte adduct. MPcs were also detectable and could serve as internal standards. Various MPcs with aromatic or aliphatic groups and different metal centers were then synthesized and explored. Aluminum-phthalocyanines (AlPcs), gallium-phthalocyanines (GaPcs), and indium-phthalocyanines (InPcs) were efficient matrices to form MPc-analyte adducts in either the positive or negative ion mode. The detection limits varied from 17 to 75 fmol, depending on analyte types. The mechanism of adducts formation was also proposed. Collectively, our strategy provides a novel and efficient way to analyze small molecules by MALDI-TOF MS.     

SiW12、PbS对提高TiO2纳米管光电转换效率的协同效应研究

复合薄膜可以改善TiO2纳米管在光电转换时电子-空穴易复合和吸收光谱范围窄的缺陷。用电沉积法将多酸H4SiW12O40（SiW12）沉积在TiO2纳米管表面形成SiW12/TiO2纳米管复合薄膜,再用连续离子层吸附反应法（SILAR）将PbS吸附到SiW12 /TiO2纳米管复合薄膜表面,形成PbS/ SiW12/TiO2纳米管复合薄膜,所得薄膜的光电转换效率相较于TiO2纳米管提高了57倍。X射线衍射（XRD）和扫描电子显微镜（SEM）表征结果表明,用电沉积法和连续离子层吸附反应法实现了PbS/SiW12/TiO2纳米管复合薄膜的制备;紫外可见（UV-vis）吸收光谱测试表明,复合薄膜的光吸收带边扩展到了可见光区域,电化学阻抗测试（EIS）表明,复合薄膜具有更高的电子转移速率;荧光光谱（PL）测试表明,复合薄膜拥有更小的电子-空穴复合率。以上结果说明,SiW12、PbS与TiO2纳米管复合,很好地抑制了TiO2纳米管电子-空穴的复合,并拓宽了吸收光谱范围,能显著地提高TiO2纳米管的光电性能。本文探索了一种有效提高TiO2纳米管光电转换效率的方法,对TiO2纳米管复合薄膜的制备具有一定的参考意义。     

Coadsorption of horseradish peroxidase with thionine on TiO2 nanotubes for biosensing

In this study, we investigate the coadsorption of protein with thionine on TiO(2) nanotubes for biosensor design. The TiO(2) nanotube arrays fabricated by anodic oxidation of titanium substrate possess large surface areas and good uniformity and conformability and are ready for enzyme immobilization. Electrochemical and spectroscopic measurements show that the TiO(2) nanotube arrays provide excellent matrixes for the coadsorption of horseradish peroxidase (HRP) and thionine and that the adsorbed HRP on these TiO(2) nanotube arrays effectively retains its bioactivity. The immobilized thionine can be electrochemically reduced but cannot be reoxidized in the electrode potential range between -0.7 and 0.0 V. The addition of H(2)O(2) leads to the biocatalytic oxidation of the reduced thionine in the presence of HRP, resulting in developing a novel H(2)O(2) sensor with good stability and reproducibility. The fabricated TiO(2) nanotubes offer a stage for further study of immobilization and electrochemistry of proteins. The proposed method opens a way to develop biosensors using nanostructured materials with low electrical conductivity.     

In situ controlled growth of well-dispersed gold nanoparticles in TiO2 nanotube arrays as recyclable substrates for surface-enhanced Raman scattering

In this paper, well-aligned Au-decorated TiO(2) nanotube arrays with high surface-enhanced Raman scattering (SERS) enhancement were prepared using a facile in situ reduction and controlled growth approach. The gold nanoparticles are well-dispersed and assembled on the mouth surface and the inside of the TiO(2) nanotubes without clogging. The structure and optical properties of the Au-decorated TiO(2) nanotube arrays have been characterized. The Au-decorated TiO(2) nanotube arrays were employed as SERS-active substrates, which exhibit good performance due to long-range coupling between Au nanoparticles, and TiO(2)-assisted enhanced charge-transfer from Au to Rh6G. The SERS activity of the substrates strongly depends on the crystallite size and level of aggregation. The substrates display significant fluorescence quenching ability and uniform SERS responses throughout the whole surface area. Particularly, good recyclability is shown. The photocatalytic property of Au-decorated TiO(2) nanotube array was exploited to recycle the substrate through UV light photocatalytic purification. The experimental results showed that the substrate is featured by high reproducibility and can be used as a highly efficient SERS substrate for multiple detection of different chemical and biological molecules.     

阳极氧化法制备TiO_2纳米管阵列膜及其应用

由阳极氧化法制备的TiO2纳米管阵列,因其独特的有序结构而显示出优异的性能,在许多领域有着广泛的应用,成为一种很有发展前景的新型纳米结构材料。本文简要综述了制备TiO2纳米管阵列结构的方法及其应用研究进展。在比较了当前几种制备TiO2纳米管阵列方法的优缺点后,重点讨论了阳极氧化法制备TiO2纳米管阵列结构过程中,如何通过调整工艺参数来实现此类纳米管阵列结构的可控生长。最后评述了TiO2纳米管阵列材料研究的发展趋势和应用前景。     

脉冲电沉积法制备Pt-TiO2 纳米管电极及其电催化性能

采用阳极氧化法在高纯钛片上原位组装TiO2纳米管阵列, 然后用脉冲电沉积方法将Pt沉积到TiO2纳米管阵列上, 制备出Pt-TiO2纳米管电极. 利用XRD和SEM对所获电极的微观结构和形貌进行表征, 结果表明, Pt纳米颗粒以花簇状分散在TiO2纳米管上, 晶粒大小约为25.6 nm. 对甲醇的电催化性能的研究结果表明, 脉冲电沉积制得的Pt-TiO2纳米管电极比TiO2纳米管电极和纯Pt片电极具有更高的电催化活性, 是Pt电极的40多倍.     

碳纳米管为基质对氨基酸的MALDI-FT MS分析

Twenty common amino acids have been analyzed successfully by matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) using carbon nanotubes as matrix. From the spectra, little or no background interference or fragmentation of the analytes has been observed. This method was also applied to the analysis of amino acid mixture successfully. Carbon nanotubes have some features such as large surface area to disperse the analyte molecules sufficiently and prevent the sample aggregation and strong ultraviolet absorption to transfer energy easily to the analyte molecules. The present method has potential application for the rapid and sensitive analysis of amino acids and their mixture.