Magnetic properties of metastable Gd-Cr alloys

We report on the magnetization, magnetocaloric effect, magnetic ordering temperatures, saturation magnetic moments and anisotropy of sputter-deposited Gd_xCr_1−x alloys with Gd atomic concentrations, x, ranging from 0.13 to 0.52. The complex magnetic nature of the Gd-Cr films was revealed from the M×H isotherms, which do not show saturation even at an applied field of 70 kOe and a temperature of 2 K and do not exhibit a linear behavior at higher temperatures. For some of the samples, the isotherms were used to determine the isothermal entropy variation as a function of temperature, for a change of 50 kOe in the applied magnetic field. The saturation magnetic moment varies with x and follows the dilution law, implying that the Cr atoms do not contribute to the total moment of the Gd-Cr alloys. Both static magnetization and dynamic susceptibility measurements reveal the existence of a magnetic glassy behavior in the alloys, which occurs below a freezing temperature. The existence of anisotropy at low temperatures for all samples was revealed by their M×H hysteresis loops from which the in-plane coercive fields, H_c, were determined. A monotonical increase in H_c with increasing Gd concentration was observed.     

Nd2(Fe1-xMnx)14B的低温内禀矫顽力

当x<0.5时,Nd₂(Fe_1-xMn_x)₁₄B可形成四方晶体结构,空间群为P4₂/mnm。在低温下,该赝三元化合物的大块铸态样品具有高矫顽力。此矫顽力不依赖于热处理等工艺过程,因此具有内禀性质。内禀矫顽力 _iH_c与样品的成分有关。Nd₂(Fe_1-xMn_x)₁₄B的起始磁化曲线具有传播场H_p,并且H_p的数值与 _iH_c接近。这表明内禀矫顽力是由畴壁钉扎造成的。研究了 _iH_c与温度的变化关系,并估算了钉扎位垒的强度。测量了Nd₂(Fe_1-xMn_x)₁₄B的居里温度和饱和磁化强度。在此赝三元化合物中,交换作用随Mn对Fe的替换而急剧降低。这使得畴壁厚度变窄。Nd₂(Fe_1-xMn_x)₁₄B的磁化和反磁化行为可用窄畴壁的特征来解释。 关键词：     

Magnetic behavior of Cd2+ substituted cobalt ferrites

The effect of Cd-substitution on the variation of saturation magnetization M_s, Curie temperature T_c, and magnetic moments n_B of Co_1?xCd_xFe₂O₄ (x=0.0–1.0 in steps of 0.1) ferrites have been investigated using SQUID magnetometer and impedance analyzer. The samples were prepared by conventional double sintering ceramic technique and found to be single-phase cubic spinel structure by X-ray diffraction. Saturation magnetization M_s, is found to increase with increase of Cd substitution attaining a maximum value at x=0.4 and decreases thereafter. Curie temperature decreases almost linearly with increasing x content up to x=0.7. Samples having x≥0.8 display complex magnetic behavior with competing antiferromagnetic and ferromagnetic interactions with the manifestation of large hysteresis at low temperature and no sign of saturation. Samples with x>0.8 show paramagnetic characteristic at T=5 K with no spontaneous magnetization revealed through Arrot-Belov-Kouvel (ABK) plots.     

GdFeCo磁光薄膜中RE-TM反铁磁耦合与激光感应超快磁化翻转动力学研究

使用飞秒时间分辨抽运-探测磁光克尔光谱技术,研究了激光加热GdFeCo磁光薄膜跨越铁磁补偿温度时稀土-过渡金属(RE-TM)反铁磁交换耦合行为和超快磁化翻转动力学. 实验观察到由于跨越铁磁补偿温度、净磁矩携带者交换而引起的磁化翻转反常克尔磁滞回线以及在同向外磁场下,反常回线上大于和小于矫顽力部分的饱和磁化强度不同,显示出GdFeCo中RE与TM之间的非完全刚性反铁磁耦合. 在含有Al导热底层的GdFeCo薄膜上观测到饱和磁场下激光感应磁化态翻转及再恢复的完整超快动力学过程. 与剩磁态的激光感应超快退磁化过 关键词： 补偿温度 磁化翻转 反铁磁耦合 GdFeCo     

Microstructure and magnetic properties of Ni-rich Ni54Mn25.7Ga20.3 ferromagnetic shape memory alloy thin film

A Ni₅₄Mn_25.7Ga_20.3 ferromagnetic shape memory alloy thin film has been fabricated by using the RF magnetron-sputtering technique. The structure and magnetic properties of the film were systematically investigated. The results show that the film is in ferromagnetic martensite state at room temperature with the Curie temperature (T_c) of about 370 K. The saturation magnetization (M_s) of the film reaches 45 emu/g at 300 K, which is about 80% as large as that of Ni–Mn–Ga bulk material. The magnetization hysteresis loops significantly depend on temperatures. The residual magnetization (M_r) and the coercive force (H_c) increase with decreasing temperatures. The grains homogeneously distribute in the film. The microstructure of the film consists of martensite plates. The interface between the martensite variants is clear and straight, indicating a good mobility.     

Magnetic properties and formation of Sr ferrite nanoparticle and Zn,Ti/Ir substituted phases

Strontium hexaferrite nanoparticles are prepared by the chemical sol–gel route. Specific saturation magnetization σ_s and coercive field strength H_c are determined depending on the heat treatment of the gel and iron/strontium ratio in the starting solution. These ultrafine powders with single-domain behavior have specific saturation magnetization σ_s=74 emu/g and coercive field strength H_c=6.4 kOe. Experimental results show that it is necessary to preheat the gel between 400 and 500°C for several hours . It can prevent the formation of intermediate γ-Fe₂O₃ and help to obtain ultrafine strontium ferrite single phase with narrow size distribution at a low annealing temperature. Additionally, the magnetic properties of sol–gel derived strontium ferrite with iron substituted by Zn²⁺, Ti⁴⁺ and Ir⁴⁺ are discussed. For an amount of substitution 0<x⩽0.6, the (Zn, Ti)_x substituted strontium ferrite shows higher values of both coercive field strength and saturation magnetization than the (Zn, Ir)_x substituted phase.     

Colossal room-temperature magnetoresistance in thin La<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ag<Subscript>y</Subscript>MnO<Subscript>3</Subscript> epitaxial films

The first thin La_1?xAg_yMnO₃ epitaxial films (_y ≤ x) were grown on SrTiO₃ (110) substrates with silver present in the ionized state (Ag⁺) only. The Curie temperatures T_C of the compositions with x = y = 0.05, x = y = 0.1, and x = 0.3 and y = 0.27 crystallizing in the hexagonal structure \(R\bar 3c\) above or close to room temperature. The temperature dependences of electrical resistivity ρ and of magnetoresistance ¦Δρ/ρ/¦ = ¦(ρ_H ? ρ _H = 0)/ρ_H=0¦ pass through maxima near T_C, with the magnetoresistance being negative and reaching colossal values of ～7–20% in a magnetic field H = 8.2 kOe not only at T_C but also at room temperature. The magnetic moment per formula unit as derived from the saturation magnetization at T = 5 K is substantially smaller than expected for complete ferromagnetic ordering. The magnetization in fields of up to 6 kOe depends on the actual sample cooling conditions, and the hysteresis loop of a field-cooled sample is displaced along the H axis by ΔH. The above properties can be accounted for by the fact that the films are in a two-phase magnetic (ferromagnetic-antiferromagnetic) state induced by strong s-d exchange. The maximum value of Δ H was used to calculate the energy of exchange coupling between the ferromagnetic and antiferromagnetic parts of a sample.     

Effects of Fe2+ content in raw materials on Mn–Zn ferrite magnetic properties

The magnetic properties of Mn–Zn ferrite such as initial permeability, saturation magnetization, Curie temperature, resistivity and power loss are affected greatly by the Fe²⁺ content in the raw materials. The experimental results show that low resistivity (ρ) and high eddy current loss (P_e) are induced by the superfluous Fe²⁺ content in the raw materials; the scant Fe²⁺ content in the raw materials will increase hysteresis loss (P_h) and decrease Curie temperature (T_c), saturation magnetization (M_s) and initial permeability (μ_i).     

Magnetic properties of iron-boron-silicon metallic glasses

The magnetic properties and crystallisation of (Fe_1-xSi_x)_1-yB_y metallic glasses have been studied over a wide composition range. Magnetic measurements included coercivity at a range of frequencies and using different maximum fields, and a region of low H_c with x>0.12 and y ～ 0.15 is found. Specific saturation magnetization at room temperature and 77 K allows the estimation of Curie temperatures θ_c. There is a plateau of σ_RT near the minimum H_c region and θ_c rises with increasing x. Based on the charge-transfer model, the best fit for the number of electrons transferred to the Fe-atoms in these glasses gives 0.6 for boron and 1.0 for silicon. Crystallisation proceeds in several stages. Stability increases as more silicon is added.     

Dependence of the coercive force on the magnetic field sweep rate in (PrDy)(FeCo)B alloys

The dependence between the coercive force and the average hysteresis loop record time was revealed in sintered (Pr_{1 – x} Dy _x )₁₃(Fe_{1 – y} Co _y )₇₉B₈ magnets. The coercive force was established to grow by 22% with an increase in the average hysteresis loop sweep rate within a range of 1.1 × 10²–3 × 10⁵ Oe/min, obeying a logarithmic dependence on the loop passage velocity with saturation at low rates. Some domain structure transformations produced by a magnetic field in the process of magnetization were established by magnetic force microscopy.     

Effect of short-range atomic order on macroscopic magnetic properties of equiatomic FePd alloy

X-ray diffraction, magnetic measurements, and Mössbauer spectroscopy were employed to comparatively analyse the relation of the basic characteristics of highly anisotropic materials– coercive force H_c and Curie temperature T_C to the peculiarities of short-range atomic order that forms upon annealing of disordered samples of equaiatomic FePd alloys produced by different techniques (casting, melt-spinning, severe deformation). It is shown that for all samples, independently of methods of their preparation, the ordered states with the maximal values of coercivity are inhomogeneous in the composition of short-ordered regions, type of atomic ordering, and degree of tetragonality. The Curie temperature depends on the temperature and duration of annealing for ordering similarly to the conventional course of coercivity, which is peculiar to these alloys. The behaviour of these macroscopic characteristics (H_c and T_C) in the course of annealing is shown to correlate with changes in the local atomic configurations revealed in the Mössbauer spectroscopy experiments.     

Magnetic properties and magnetocaloric effect of Sr-doped Pr0.7Ca0.3MnO3 compounds

In this work, we pointed out that Sr substitution for Ca leads to modify the magnetic and magnetocaloric properties of Pr_0.7Ca_0.3-xSr_xMnO₃ compounds. Analyzing temperature dependence of magnetization, M(T), proves that the Curie temperature (T_C) increased with increasing Sr content (x); T_C value is found to be 130–260 K for x = 0.0–0.3, respectively. Using the phenomenological model and M(T,H) data measured at several applied magnetic field, the magnetocaloric effect of Pr_0.7Ca_0.3-xSr_xMnO₃ compounds has been investigated through their temperature and magnetic field dependences of magnetic entropy change ΔS_m(T,H) and the change of the specific heat change ΔC_P(T,H). Under an applied magnetic field change of 10 kOe, the maximum value of -ΔS_m is found to be about 3 J/kg·K, and the maximum and minimum values of ΔC_P(T) calculated to be about ±60 J/kg·K for x = 0.3 sample. Additionally, the critical behaviors of Pr_0.7Ca_0.3-xSr_xMnO₃ compounds around their T_C have been also analyzed. Results suggested a coexistence of the ferromagnetic short- and long-range interactions in samples. Moreover, Sr-doping favors establishing the short-range interactions.     

Structural and magnetic properties of holmium substituted cobalt ferrites synthesized by chemical co-precipitation method

CoHo_xFe_2−xO₄ ferrites (x=0.00–0.1) were prepared by the co-precipitation technique and the effect of holmium substitution on the magnetic properties was investigated. X-ray diffraction reveals that the substituted samples show a second phase of HoFeO₃ along with the spinel phase. The magnetic properties such as the saturation magnetization (M_s), coercivity (H_c) and remanence (M_r) are obtained from the hysteresis loops. It is observed that the M_s decreases while H_c increases with Ho³⁺ substitution. The decrease of saturation magnetization is attributed to the weakening of exchange interactions. The coercivity increases with increase of the Ho³⁺ concentration, which is attributed to the presence of an ultra-thin layer at the grain boundaries that impedes the domain wall motion. Low field AC susceptibility was also measured over the temperature range 300–600 K at the frequency of 200 Hz. It decreases with the increase of temperature following the Curie–Weiss law up to the Curie temperature. Above the Curie temperature it shows paramagnetic behavior. The increase in coercivity suggests that the material can be used for applications in perpendicular recording media.     

Magnetic and electrical investigations of Fe<Subscript>85-x</Subscript>Co<Subscript>x</Subscript>B<Subscript>15</Subscript> metallic glasses

The magnetic and electrical properties of metallic glasses with the general formula Fe_85-xCo_xB₁₅ were investigated over a large temperature range to study their concentration-dependent physical parameters. All of the samples investigated (x=17,21,30, and 40) were soft ferromagnets with coercive fields H_c1 Oe and high Curie temperatures slightly above 1200 K. The temperature-dependent magnetization behaved irregularly, and exhibited hysteresis during heating and subsequent cooling through the Curie temperature. The variation of the magnetization with temperature demonstrates that one or more phase transformations (crystallization) occurred in the course of the heating. The electrical resistivities exhibited positive temperature coefficients and minima at temperatures below 50 K. We did not observe a nonmonotonic variation of the magnetic and electrical properties with a monotonic change of the Fe_85-xCo_xB₁₅ composition that would correlate with the earlier proposed formation of strong nanoclusters in the vicinity of particular stoichiometrically close Fe:Co ratios. The good soft magnetic characteristics make the Fe_85-xCo_xB₁₅ metal glasses promising candidates for engineering materials in inductive applications. PACS 71.23.Cq; 75.75.+a     

Magnetic properties of Fe<Subscript>3</Subscript>C ferromagnetic nanoparticles encapsulated in carbon nanotubes

The low-temperature dependences of magnetic characteristics (namely, the coercive force H _c , the remanent magnetization M _r , local magnetic anisotropy fields H _a, and the saturation magnetization M _s ) determined from the irreversible and reversible parts of the magnetization curves for Fe₃C ferromagnetic nanoparticles encapsulated in carbon nanotubes are investigated experimentally. The behavior of the temperature dependences of the coercive force H _c (T) and the remanent magnetization M _r (T) indicates a single-domain structure of the particles under study and makes it possible to estimate their blocking temperature T _B = 420–450 K. It is found that the saturation magnetization M _s and the local magnetic anisotropy field H _a vary with temperature as ～T ^5/2.     

Magnetic properties and hydrostatic pressure effect on the curie temperature of (Co,Mn)2B amorphous alloys

The temperature dependence of magnetization and magnetic susceptibility and hydrostatic pressure effect on the Surie temperature (dT_c/dP) are measured for (Co_1-xMn_x)₂B (0?x?0.4) amorphous alloys and the results are compared with those of crystalline compounds with the same composition. The Curie temperature decreases linearly with an increasing Mn content but magnetization shows a maximum around x=0.15. The reciprocal magnetic susceptibility of all the prepared alloys obeys the Curie-Weiss law above T_c. The magnitude of the negative value of dT_c/dP decreases linearly with increasing x from about 1.1 K/kbar (x=0) to zero (x=0.4), the composition dependence of which is opposite to that of the crystalline compound. The composition dependence of the average magnetic moment per transition metal atom and the Curie temperature and dT_c/dP are analysed on the basis of the local environment and the pair order interaction mode, respectively.     

Magnetic properties of PrCo2 and its ternary hydride PrCo2H4

Magnetization and susceptibility data on PrCo₂ and PrCo₂H₄ are presented. The ac susceptibility of PrCo₂ measured in zero dc field displays a sharp and high peak at T_c = (39.9 ± 0.2) K. The magnetization versus temperature curves show ferromagnetic behaviour for B >1 T, but display a maximum at lower values of the applied field. These results, together with the behaviour of the hysteresis loops at different temperatures below T_c, indicate that PrCo₂ orders ferromagnetically, the magnetic hardness increasing strongly for T → 0. The saturation moment at 4.2 K equals 3.9 μ_B per formula unit, as found from the magnetization curve measured in a pulsed-field magnet up to B = 30 T.Similar experiments on PrCo₂H₄ provide evidence that the introduction of hydrogen in PrCo₂ not only destroys the long-range atomic order, but also considerably reduces the ferromagnetic interactions. Such an effect of the hydrogen is commonly observed in cobalt intermetallics. Part of the PrCo₂H₄ is found to have decomposed into PrH₂ and free Co. The clusters of free Co atoms give rise to a maximum in the zero-field ac susceptibility versus temperature curves, similar as observed in spin glasses or magnetic glasses. By increasing the ac frequency, the maximum shifts to higher temperatures. The behavior can be explained in terms of the Néel model for superparamagnetic particles with randomly oriented local anisotropy axes.     

Effect of annealing on the magnetic and magnetooptical properties of Ni films

The magnetic and magnetooptical properties of 50-to 200-nm-thick Ni films, both as-deposited and annealed at T_ann = 300, 400, or 500°C, were studied. Volume and near-surface hysteresis loops were measured with a vibrating-sample magnetometer (VSM) and with the use of the transverse Kerr effect (TKE). The annealing temperature was found to exert a strong effect on the magnetic characteristics of the samples under study. It was established, in particular, that the coercivity H _C of Ni films increases and the remanent magnetization decreases with increasing annealing temperature. The observed dependences of the magnetic properties of the films on film thickness and annealing temperature are explained as being due to microstructural characteristics of the samples. It was found that, while TKE spectra obtained in the incident-photon energy region from 1.5 to 6 eV have the same shape for all the Ni films studied, the magnitude of the TKE decreases with increasing T_ann. This experimental observation is accounted for by the decreased saturation magnetization of the annealed films.     

Structural, magnetic and magnetocaloric properties of La0.7−xEuxBa0.3MnO3 perovskites

Polycrystalline perovskite manganites La_0.7−xEu_xBa_0.3MnO₃(x=0.05, 0.1 and 0.15) were prepared by sol-gel method. The prepared samples remain single phase with a perovskite structure, revealed by X-ray diffraction. The structure refinement of La_0.7−xEu_xBa_0.3MnO₃(x=0.05, 0.1 and 0.15) samples was performed in the hexagonal setting of the R3¯c space group. The dependence of magnetization M on applied magnetic field H and temperature T was measured carefully near the Curie temperature T_C for all the samples. With the increasing Eu content, both the unit cell volume and Curie temperature T_C of 298 K has been detected with a maximum of magnetic entropy |ΔS_M^max| for the La_0.7−xEu_xBa_0.3MnO₃ with x=0.15, reaching a value of 2.3 J/kg K when a magnetic field of 10 kOe was applied and the relative cooling power (RCP) is 46 J/kg. These results suggest that the material may be a suitable candidate as working substance in magnetic refrigeration near room temperature.     

Rfe10.5V1.5Nx化合物的结构和内禀磁性研究

系统地研究了Rfe_10.5V_1.5N_x（Ｒ＝Ｙ，Ｃｅ，Ｎｄ，Ｓｍ，Ｇｄ，Ｔｂ，Ｄｙ，Ｈｏ，Ｅｒ）化合物的结构和内禀磁性，并与相应的Rfe_10.5V_1.5N_x化合物进行了比较。同Rfe_10.5V_1.5N_x化会物相比，由于ｖ含量低，Rfe_10.5V_1.5N_{x关键词：}