Influence of TiO2 particles and APP on combustion behavior and mechanical properties of flame-retardant thermoplastic polyurethane

The experimental investigation on combustion behavior and mechanical properties of flame-retardant thermoplastic polyurethane were performed in the article. By the masterbatch-melt blending technique, the TiO₂ particles were well dispersed in TPU/APP composites. The microscopic morphology structure was observed by TEM and SEM. TEM images of TPU–TiO₂ masterbatch material showed that the grain sizes of TiO₂ particles were 200–400 nm. The SEM result indicated that the TiO₂ particles could enhance compatibility and dispersion of APP in TPU. The mechanical properties of TPU composites were characterized by dynamic mechanical analysis (DMA) and tensile tests, respectively. The DMA results indicated that TiO₂ particles could improve the viscoelastic property of the TPU/APP composites. The tensile strength achieved a significant improvement with addition of TiO₂ particles. APP/TiO₂-5 obtains a better value of 344% than APP-1 (277%). Also, the flame-retardant property and thermal stability of the TPU composites were characterized using cone calorimeter test (CCT) and thermogravimetric analysis (TGA), respectively. The CCT results revealed that TiO₂ particles could enhance the flame-retardant property of APP in TPU. The peak heat release rate of APP/TiO₂-4 containing 0.5% TiO₂ decreased to 157.27 kW m^?2 from 225.5 kW m^?2 of APP-1 sample without any TiO₂. The TiO₂ particles could promote the formation of carbon layers which restrict the diffusion of fuels into combustion zone and access of oxygen to the underlying materials. The TGA results indicated that TiO₂ can improve the thermal stability of TPU/APP composites.

     

Synthesis of TiO2 based on hydrothermal methods using elevated pressures and microwave conditions

Titanium dioxide (TiO₂), especially in its anatase form, is an effective photocatalyst under ultraviolet (UV) light. The particle size of TiO₂ is a critical factor to determine its photoactivity based on its quantum effectiveness under light irradiations. Thus, nanocrystalline TiO₂ has been widely accepted to significantly enhance this effect. The sol–gel method is generally used to synthesize the anatase form of nanocrystalline TiO₂. In this study, we expanded the synthesis method of TiO₂ to high pressures under direct heating (hydrothermal method) and indirect heating (microwave-assisted method). It was found that pH value is one of the major factors to control nano-sizes of TiO₂ particles, and the neutral condition in all methods is preferable for controlling the sizes of the prepared TiO₂ particles. The microwave-assisted method further improves quality of synthesized nano-size TiO₂ below 10 nm. These results have been confirmed by both the direct size measurement using TEM images and indirect determination using XRD peaks. The collected samples are further analyzed using UV–Vis spectroscopy to identify the particle size-dependent photoreactivity and to confirm the effectiveness of microwave-assisting under neutral conditions. DSC is also a powerful tool to identify the crystalline transition of TiO₂.     

可见光响应的铁掺杂TiO_2中空微球的制备及其光催化性能

以聚苯乙烯微球作为模板,水溶性过氧化钛配合物作为前驱体一步合成了掺铁TiO2中空微球,并利用XRD,SEM,TEM,XPS,UV-Vis等测试手段对样品进行了表征。结果表明,一步法制备的掺铁TiO2中空微球以锐钛矿相存在且具有良好的中空结构,掺杂少量铁到体系中,改变了其电子结构,使其吸收波长拓展到可见光区。光催化降解亚甲基蓝溶液的结果表明,掺杂0.75%铁的TiO2中空微球表现出更好的光催化性能。对Fe3+影响光催化活性的机理进行了讨论。     

Quantitative Distinction between Noble Metals Located in Mesopores from Those on the External Surface

We compare three methods for quantitatively distinguishing the location of noble metal (NM) particles in mesopores from those found on the external support surface. MCM-41 and SBA-15 with NM located in mesopores or on the external surface were prepared and characterized by TEM. ³¹P MAS NMR spectroscopy was used to quantify arylphosphines in complexes with NM. Phosphine/NM ratios drop from 2.0 to 0.2 when increasing the probe diameter from 1.08 to 1.54 nm. The reaction between NM and triphenylphosphine (TPP) within 3.0 nm MCM-41 pores takes due to confinement effects multiple weeks. In contrast, external NM react with TPP instantly. A promising method is filling the pores by using the pore volume impregnation technique with tetraethylorthosilicate (TEOS). TPP loading revealed that 66 % of NMs are located on the external surface of MCM-41. The pore filling method can be used in association with any probe molecule, also for the quantification of acid sites.     

Synthesis and Characterization of Copper Ferrite Nanocrystals via Coprecipitation

Nanocrystalline CuFe₂O₄ powder was prepared by a coprecipitation method from iron chloride and copper chloride in the presence of octanoic acid (C₈H₁₆O₂) as surfactant. The as-prepared samples were characterized by XRD, TEM, SEM, FT-IR and VSM. SEM and TEM indicated that the particles were quasi spherical with the particle sizes in the range of 23±7?nm. The magnetic properties of the sample were measured by using a vibration sample magnetometer (VSM), which showed that the sample exhibited a typical ferromagnetic behavior at room temperature, while present finite coercivity of 245.5?Oe at 300?K.     

Comparative studies of gold catalysts prepared via solvated metal atom impregnation and conventional impregnation: characterization and low-temperature co oxidation

Supported Au catalysts for low-temperature CO oxidation were prepared by solvated metal atom impregnation (SMAI) and conventional impregnation (CI). X-ray photoelectron spectroscopy investigations indicated that gold in all the samples was in the metallic state. TEM and XRD measurements showed that the mean diameter of Au particles prepared by SMAI was smaller than that of those prepared by CI with the same gold content. Catalytic tests showed that SMAI catalysts had higher CO oxidation activity than CI catalysts with the same compositions. Both SMAI and CI Au/TiO₂catalysts exhibited high activities in low temperature CO oxidation. Full CO conversion was obtained at 323 K for 3.1 wt.% Au/TiO₂ (SMAI) catalyst, which displayed higher activity than the 3.1 wt.% Au/D-72(SMAI) and 3.1 wt.% Au/TiO₂(CI). Although the sizes of gold particles prepared by the same method and supported on both TiO₂ and resin were comparable, the Au/TiO₂ catalysts showed significantly higher activities than the Au/resin catalysts with the same Au contents under the same reaction conditions. These results prove that not only the gold particle size, but also the support plays a key role in CO oxidation. This revised version was published online in June 2006 with corrections to the Cover Date.     

Thermal behaviour study of some sol-gel TiO2 based materials

Among the great number of sol-gel materials prepared, TiO₂ holds one of the most important places due to its photocatalytic properties, both in the case of powders and coatings. Impurity doping is one of the typical approaches to extend the spectral response of a wide band gap semiconductor to visible light. This work has studied some un-doped and Pd-doped sol-gel TiO₂ nanopowders, presenting various surface morphologies and structures. The obtained powders have been embedded in vitreous TiO₂ matrices and the corresponding coatings have been prepared by dipping procedure, on glass substrates. The relationship between the synthesis conditions and the properties of titania nanosized materials, such as thermal stability, phase composition, crystallinity, morphology and size of particles, and the influence of dopant was investigated. The influence of Pd on TiO₂ crystallization both for supported and unsupported materials was studied (lattice parameters, crystallite sizes, internal strains). The hydrophilic properties of the films were also connected with their structure, composition and surface morphology. The methods used for the characterization of the materials have been: simultaneous thermogravimetry and differential thermal analysis, powder X-ray diffraction, electron microscopy (TEM, SAED) and AFM.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

A simple route to synthesize nanocrystalline nickel ferrite (NiFe2O4) in the presence of octanoic acid as a surfactant

Nanocrystalline nickel ferrite (NiFe₂O₄) powder was prepared by a co-precipitation method from Ni and Fe chlorides. The as-prepared samples were characterized by powder X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry (VSM). SEM and TEM indicated that the particles were spherical with particle sizes in the range 25 ± 5 nm. The magnetic properties of the sample were measured by using a vibrating sample magnetometer, which showed that the sample exhibited typical ferromagnetic behavior at room temperature, while a finite coercivity of 245.5 Oe was present at 300 K. The saturation magnetization of the sample (23.13 emu/g) was significantly lower than that for the reported multidomain bulk particles (55 emu/g), reflecting the ultrafine nature of the sample.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Particle size measurements of heterogeneous film-forming latexes

Two-phase latex particles consisting of mainly polystyrene (PS) and polyisoprene (PI) in ratios varying from 7030 to 2080 were prepared using different polymerization techniques. Methacrylic acid (MAA) was used in small amounts as a comonomer. The latexes had narrow size distributions, and showed different particle morphologies depending on the monomer composition and the polymerization conditions used. In most cases the latexes were filmforming at room temperature. Particle size distributions and average particle sizes of the latexes have been determined using different particle sizing methods.Size determination by TEM was performed after staining with osmium tetroxide (OsO₄) or uranyl acetate (UAc). The staining methods showed no significant differences in particle size averages and particle size distributions when the ratio between the PI and PS phase did not exceed 5050. At higher phase ratios OsO₄ staining was preferred. The glass transition temperature of the PI phase increased after OsO₄ staining, which prevented deformation of the latex particles. Particle morphologies for the heterogeneous latex particles were also determined after OsO₄ staining.Particle sizes measured by TEM were generally smaller than the corresponding sizes measured by quasielastic light scattering (QELS). The difference in the measured diameters increased with increasing PI and PMAA content in the latex particles. The larger sizes observed by QELS are results of the presence of an immobilized water layer surrounding the particles in the aqueous environment, water absorption and swelling due to the presence of carboxylic acid groups, and adsorption of soluble carboxylated polymers forming a hydrophilic corona around the particles. By TEM the hard sphere diameters of dehydrated particles are measured.     

Preparation and characterization of poly(methyl methacrylate)/titanium oxide composite particles

Before polymerization, the introduction of double bonds onto the surface of the TiO₂ particles was achieved by the treatment of the TiO₂ particles with the silane-coupling agent. Via in-situ emulsion polymerization, the poly(methyl methacrylate) (PMMA)/titanium oxide (TiO₂) composite particles were prepared by graft polymerization of MMA from the surface of the modified TiO₂ particles. The structure of the obtained PMMA/TiO₂ composite particles was characterized using fourier transform infrared spectra (FT-IR), thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC) and size excluding chromatography (SEC). The morphology of the obtained PMMA/TiO₂ composite particles was observed by transmission electron microscope (TEM). The results of FT-IR and TGA measurements show that PMMA is successfully grafted from the surface of the TiO₂ particles and that the percentage of grafting and the grafting efficiency can reach 208.3% and 96.6%, respectively. At the same time, the TGA and DSC measurements indicate an enhancement of thermal stability. TEM images demonstrate a better dispersion of the TiO₂ particles in the composite latex. In addition, UV-visible absorption measurements show that the PMMA/TiO₂ composite particles can absorb over 95% UV light at 210–400 nm wavelength.     

Nanocomposite based on modified TiO2–BSA for functional applications

A novel nanocomposite based on TiO₂–protein for functional applications was prepared and characterized. The composite was made by covalent immobilisation of bovine serum albumin (BSA) on to the TiO₂ particles. BSA was attached to the TiO₂ powder through a three-step process. This involves the functionalization of the TiO₂ particles with silane and the subsequent coupling by glutaraldehyde to free NH₂ groups of the protein. Formation of Schiff's base was confirmed by IR spectroscopy and the optimum loading of the BSA was found to be 73.61%. Surface morphology of the composite was studied by SEM and TEM. Thermal analysis of TiO₂–BSA composite was carried out by TGA and DSC. Structural variation of the BSA after immobilisation was studied by CD spectra.     

Exposed crystal surface-controlled TiO2 nanorods having rutile phase from TiCl3 under hydrothermal conditions

Size-, shape-, and phase structure-controlled synthesis of TiO₂ nanocrystallites has long been one of the main themes in TiO₂ research. Many synthetic techniques have been utilized in the preparation of TiO₂ nanocrystals, among which hydrothermal treatment has been drawing much attention because it directly produces well-crystallized nanocrystallities of a wide range of compositions of crystal phases within a short reaction time. In this study, we carried out hydrothermal growth of rutile TiO₂ rods by using aqueous titanium trichloride (TiCl₃) solutions containing NaCl. Uniform ultrafine rutile TiO₂ particles were obtained, and developed crystal faces were observed by TEM, SEM, XRD, and specific surface area measurements. The obtained rutile fine particles showed high levels of activity for degradation of 2-propanol and acetaldehyde under UV irradiation compared to the activity levels of anatase fine particles (ST-01) developed for environmental clean-up. The surface chemistry of the rutile TiO₂ particles was also investigated. From photodeposition of Pt and PbO₂, we suggest that the (1 1 0) face provides reductive sites and that the (1 1 1) face provides oxidative sites. These results indicate that the crystal faces facilitate the separation of electrons and holes, resulting in improvement of photocatalytic activity.     

Three-dimensionally ordered macro-porous Pt/TiO2 catalyst used for water-gas shift reaction

Three-dimensionally ordered macro-porous （3DOM） Pt/TiO2 catalysts were prepared by template and impregnation methods, and the resultant samples were characterized by using TG-DTA, XRD, SEM, TEM, and TPR techniques. The catalytic performance for water-gas shift （WGS） reaction was tested, and the influences of some conditions, such as reduction temperature of catalysts, the amount of Pt loadings and space velocity on catalytic performance were investigated. It was shown that Pt particles were homogeneously dispersed on 3DOM TiO2. The reduction of TiO2 surface was important for the catalytic performance. The activity test results showed that the 3DOM Pt/TiO2 catalysts exhibited very good catalytic performance for WGS reaction even at high space velocity, which was owing to the better mass transfer of 3DOM porous structure besides the high intrinsic activity of Pt/TiO2.     

Preparation of raspberry-like PMMA/SiO2 nanocomposite particles

Water-borne raspberry-like PMMA/SiO₂ nanocom-posite particles were prepared via free radical copolymerization of methyl methacrylate (MMA) with 1-vinylimidazole (1-VID) in the presence of ultrafine aqueous silica sols. The acid-base interaction between hydroxyl groups (acidic) of silica surfaces and amino groups (basic) of 1-VID was strong enough for promoting the formation of long-standing stable PMMA/SiO₂ nanocomposite particles when 10 mol% or more 1-VID as auxiliary monomer was used. The average particle sizes and the silica contents of the nanocomposite particles were in the ranges from 120–330 nm and 15%–20%, respectively. TEM and SEM observations indicated a raspberry-like morphology of the obtained nanocomposite particles. __________ Translated from Chemical Journal of Chinese Universities, 2005, 26(7) (in Chinese)     

High-power ultrasonic-assisted phenol and dye degradation on porous manganese oxide doped titanium dioxide catalysts

In this study, a high-power ultrasonicator (600 W) is employed to examine dye degradation and phenol decomposition efficiencies in the presence of catalysts such as K-OMS-2, TiO₂, K-OL-1 doped TiO₂ and K-OMS-2 doped TiO₂. Methylene blue and phenol are chosen as the model pollutants to test the catalytic activity. Effects of ultrasonic power level or ultrasonic intensity, amount of catalysts used and ultrasonic irradiation time for catalytic degradation and removal of phenol were studied. No d-spacing peak shift was observed in intense XRD peaks of K-OMS-2- and K-OL-1-doped TiO₂ materials when compared with commercial TiO₂. Scanning and transmission electron micrographs (SEM and TEM) show aggregated particle morphology with spherical and rectangular particles for 5 wt % K-OMS-2/TiO₂. Methylene blue dye degradation efficiency in the presence of catalytic ultrasonication follows the order like TiO₂ > 5 wt % K-OMS-2/TiO₂ > 5 wt % K-OL-1/TiO₂. The K-OMS-2- and 5 wt % K-OMS-2-doped TiO₂ catalyst showed the best and most promising efficiency for phenol removal in ultrasonication process. K-OMS-2 shows the best phenol removal efficiency of 58% within a short duration (30 min) of catalytic ultrasonic-assisted reaction.     

Preparation of nanocrystalline anatase TiO2 using basic sol-gel method

Nanocrystalline titanium dioxide particles with anatase structure and high thermal stability have been synthesized using the basic sol-gel method. The particle size and morphology were refined under hydrothermal conditions in the presence of different concentrations of tetramethylammonium hydroxide (TMAH) at 210°C and 230°C. XRD and TEM analysis showed that the TiO₂ particles obtained were homogeneous and monodispersive at low contents of TMAH. All intense peaks, clearly observed in the XRD patterns, were assigned to the anatase phase and no rutile phase was observed. At high contents of TMAH, nanoscale small (10–30 nm) and larger (>100 nm) TiO₂ particles were one-pot synthesized. The nanocrystalline TiO₂ particles synthesized by this method have good thermal stability. With the sintering temperature of up to 650°C, all the XRD peaks maintained good agreement with the anatase reference data.     

Controlled crystal phase and particle size of loaded-TiO2 using clinoptilolite as support via hydrothermal method for degradation of crystal violet dye in aqueous solution

TiO₂-supported clinoptilolites (TiO₂/clinoptilolites) were successfully synthesized with controlled crystal phase and particle size via hydrothermal method to enhance photocatalytic performance of TiO₂. The effects of various parameters including temperature, acidity and concentration of Ti-containing solutions on the particle size, crystal phase and agglomeration of TiO₂ supported on clinoptilolite were investigated thoroughly by characterizations of X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), BET isotherm, UV–visible (UV–vis) spectrophotometer and Malvern zetasizer. The results demonstrate that increasing temperature and strengthen acidity are beneficial to enhance the crystallinity and particle size of supported TiO₂. Increase in acidity also leads to more uniform distribution of TiO₂ on the surface of clinoptilolite. The TiO₂ nano-crystals deposited on the surface of clinoptilolite, exhibit rutile or anatase phase, strongly depending on the preparation procedure. The resultant TiO₂/clinoptilolites could be used as photo-catalysts for the degradation of crystal violet (CV) dye in aqueous solution, showing a higher photo-catalytic activity with 89% degradation within 100 min. The effect of operational parameters, such as pH values of reaction media, dose of used catalyst, and concentration of CV dye on the CV degradation performance were investigated, in which the kinetics of CV dye degradation was found to follow the pseudo-first order kinetic model.     

Structure and photocatalytic activity of Ti1?X MX O2 (M = Zr, Co and Mo) synthesized by pulverized solid state technique

A set of transition metal doped nanosized TiO₂ particles with anatase structure were synthesized by the pulverization method and their ability to photocatalytically degrade the dye Alizarin Red S was investigated. Characterization of the Zr-, Co- and Mo-doped photocatalysts was conducted with the aid of XRD, SEM, EDX, TEM, BET and spectral analysis. X-ray diffraction patterns did not reflect the appearance of any peaks due to dopants, however dopants were observed in SEM-EDX analysis. Particle sizes were in the range of 25 nm as per TEM and XRD analysis. Upon doping, a prominent decrease in surface area was observed. The percentage composition of each of the dopants was confirmed by EDX analysis. Doped samples depicted many mid-bands in the Kubelka Munk plots due to d-d transition of dopants. Experiments were conducted to compare the photocatalytic activity under identical UV and solar light exposure. Zr-doped TiO₂ at the molecular scale exhibited better photocatalytic activity in degradation of Alizarin, with a lower band-gap energy that can respond to visible light. However, Co- and Mo-doped TiO₂ appeared to suppress the photoactivity. A rise in the number of mid-bands causing effective separation or recombination of charge carriers strongly influences the rate of the degradation process.