Properties of Natural Rubber/Recycled Chloroprene Rubber Blend: Effects of Blend Ratio and Matrix

The present study investigated the effects of two types of natural rubber and different blend ratios on the cure, tensile properties and morphology of natural rubber/recycled chloroprene rubber blends. The blends of natural rubber/recycled chloroprene rubber were prepared by using laboratory two-roll mill. The result showed that the cure time prolonged with the addition of recycled chloroprene rubber (rCR). Comparability, natural rubber/recycled chloroprene rubber (SMR L/rCR) blendcured rapidly than epoxidized natural rubber/recycled chloroprene rubber (ENR 50/rCR) blend. The addition of rCRalso caused a decrement in the tensile strength and elongation at break for both rubber blends. The SMR L/rCR blendsshowed higher tensile strength and elongation at break compared to those of ENR 50/rCR blends at any blend ratios.     

Development of novel elastomeric blends derived from chlorinated nitrile rubber and chlorinated ethylene propylene diene rubber

Chlorinated nitrile rubber (Cl-NBR) has been blended with chlorinated ethylene propylene diene rubber (Cl-EPDM) in different ratios by a conventional mill mixing method. The effect of the blend ratio on processing characteristics, mechanical properties (such as tensile and tear strength, elongation at break, hardness, abrasion resistance, heat build-up and resilience), structure, morphology, glass transition temperature (Tg), thermal stability, flame retardancy, oil resistance, AC conductivity, dielectric properties and transport behavior of petrol, diesel and kerosene were investigated. The shift in absorption bands of blends studied from FTIR spectra, single Tg from DSC analysis and decrease in amorphous nature from XRD showed the molecular miscibility in Cl-NBR/Cl-EPDM blends. SEM images showed the uniform mixing of both Cl-NBR and Cl-EPDM in a 50/50 blend ratio. The TGA curves indicated the better thermal stability of the polymer blend. The elongation at break, heat build-up, resilience and hardness of the polymer blend decreases with an increase in Cl-NBR content in the blend whereas the flame and oil resistance were increased with increase in Cl-NBR content. Among the polymer blends, the maximum torque, tensile strength, tear and abrasion resistance was obtained for the 50/50 blend ratio because of the effective interfacial interactions between the blend components. AC conductivity and dielectric properties of polymer blend increased with increase in the ratio of Cl-NBR in the blend. Different transport properties such as diffusion, permeation and sorption coefficient were measured with respect to nature of solvent and different blend ratios. Temperature dependence of diffusion was used to estimate the activation parameters and the mechanism of transport found to be anomalous.     

Solid-state morphology,structure, and tensile properties of polyethylene/polyamide/nanoclay blends: Effect of clay fraction

The effect of nanoclay fraction on the linear and non-linear tensile properties of a polyethylene/polyamide 12 blend with droplet morphology was investigated. All ternary blends were prepared at a fixed polyamide (PA) weight fraction of 20%, and at clay volume fractions varying from 0.5 to 2.5% relative to PA. Scanning electron microscopy and transmission electron microscopy were used to characterize the morphology of the blends and the clay interphase structure. The nanoclay content was shown to strongly influence both linear and non-linear tensile properties. Young's modulus, elongation at yield, yield strength, tensile strength and elongation at break as a function of clay fraction were studied and discussed in terms of morphological changes and strain-induced structural reorganization of the clay interphase.     

Thermal and mechanical properties of UV irradiated collagen/chitosan thin films

The thermal and mechanical properties of collagen/chitosan blends before and after UV irradiation have been investigated using thermal analysis and mechanical (Instron) techniques. Comparisons were made with the thermal and mechanical properties of both collagen and chitosan films. Air-dried collagen, chitosan and collagen/chitosan films were exposed to UV irradiation (wavelength 254 nm) for different time intervals. Thermal properties of collagen/chitosan blends depend on the composition of the blend and are not significantly altered by UV irradiation.Mechanical properties such as ultimate tensile strength and ultimate percentage of elongation were much better for collagen films than for collagen/chitosan films. The results have shown that the mechanical properties of the blends were greatly affected by the duration of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the blend. Increasing UV irradiation leads to an increase in Young's modulus of the collagen/chitosan blend.     

Blends of polycarbonate and ethylene-1-octylene copolymer

The mechanical properties and morphology of polycarbonate/ethylene-1-octylene copolymer (PC/POE) binary blends and PC/POE/ionomer ternary blends were investigated. The tensile strength and elongation at break of the PC/POE blends decreased with increasing the POE content. The impact strength of the PC/POE blends showed less dependence on thickness than that of PC. And the low-temperature impact strength of PC was modified effectively by addition of POE. The morphology of the PC/POE blends was observed by scanning electron microscope. The PC/POE weight ratio had a great effect on the morphology of the PC/POE blends. For the PC/POE (80/20)/ionomer ternary blends, low content (0.25 and 0.5 phr) of ionomer could increase the tensile properties of PC/POE (80/20) blend and had little effect on the impact strength. And 0.5 phr ionomer made the dispersed domain distribute more uniformly and finely than the blend without it. But with high content of ionomer, the degradation of PC made the mechanical properties of the blends deteriorate. Blending PC and ionomer proved the degradation of PC, and the molecular weight decreased with increasing the ionomer content.     

Breakthrough in the preparation of irradiated sodium alginate/polyethylene oxide blend films using methacrylate monomer

The present work is an attempt to prepare biodegradable films of sodium alginate (SA)/polyethylene oxide (PEO) blend tailored by methacrylate (MA) and γ irradiation following casting method. The effects of SA/PEO composition, glycerol as a plasticizer, methacrylate as a monomer, and radiation dose were investigated and it was found that the mechanical properties of the films strongly depend on the film-forming parameters. The incorporation of glycerol in the blend is crucial as it creates a suitable environment for monomer addition and points out that tensile strength of the films decreased, while the elongation at break increased. Moreover, it was found that the tensile properties were improved by the application of γ radiation as well as monomer treatment. The mechanical properties of the blend films integrated with MA monomer were higher than that without monomer at the analogous conditions. The structural and morphological features of the films were examined by Fourier transform infrared spectroscopy and scanning electron microscopy, respectively.     

Radiation Vulcanization of Nitrile Butadiene Rubber/Butadiene Rubber Blends

Blends of nitrile butadiene rubber (NBR) with butadiene rubber (BR) with varying ratios have been prepared. Vulcanization of prepared blends has been induced by ionizing radiation of gamma rays with varying dose up to 250 kGy. Physical properties, namely soluble fraction and swelling number have been followed up using toluene as a solvent. Mechanical properties, namely tensile strength, tensile modulus at 100% elongation and elongation at break have been followed up as a function of irradiation dose, as well as blend composition. Thermal stability of blends was studied by TGA. The result indicated that the addition of NBR has improved the properties of NBR/BR blends. Also, NBR/BR blend is thermally stable than BR alone.     

The compatibilizing effect of epoxy resin (EP) on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) blends

A new method was used to prepare thermoplastic elastomers based on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) with improved mechanical properties. An epoxy resin (EP) was used as a compatibilizing agent. The effect of EP on mechanical properties, swelling percentage and morphological characteristics of the blends was investigated with different blend compositions. The results showed that the incorporation of EP has improved the tensile strength, Young's modulus and elongation at break of PP/NBRr-EP blends compared with PP/NBRr blends. The enhancement of tensile properties of PP/NBRr-EP blends is due to the better adhesion between the two phases with the incorporation of EP. This is quite evident by scanning electron microscopy of tensile fractured surfaces. PP/NBRr-EP blend exhibits lower stabilization torque and swelling percentage than PP/NBRr blends. The lower stabilization torque is an indication of better processing characteristics.     

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

A high temperature thermosetting bisphenol A dicyanate (BADCy) was modified with a novel thermoplastic poly(ether-imide) (PEI) at various compositions. Fourier transform infrared spectroscopy was used to measure the conversion of BADCy. Curing kinetics of the BADCy/PEI blend were studied by the dynamic differential scanning calorimeter method. Morphologies of PEI-modified polycyanurates were investigated by scanning electron microscopy (SEM). It was found that the phase structures of the blends changed dramatically with the PEI content and molecular weight. The tensile results showed that the mechanical properties could be correlated with the morphologies. The blend with cocontinuous morphology had the highest tensile strength and elongation at break while the blend with ribbon-like morphology had the lowest one despite PEI molecular weight.     

Morphologies and mechanical properties of <Emphasis Type="Italic">cis</Emphasis>-1,4-butadiene rubber/polyethylene blends

The mechanical properties and phase morphologies of cis-1,4-butadiene rubber (BR) blended with polyethylene (PE) at different blend ratios were studied. The tensile test results show that the PE exhibits excellent reinforcing capabilities towards BR. Blending BR with PE results in a remarkable enhancement of tensile strength, modulus and the elongation at break simultaneously. An increment of tensile strength from 1.11 MPa to 16.26 MPa was achieved by incorporation of 40 wt% PE in the blends. The modulus and elongation at break of 40/60 PE/BR blends are also about 5 times higher than those of the pure BR treated under exactly the same conditions. The tear test indicates that the tear strength also increases with the increase of PE content. It reaches 58.38 MPa for the 40/60 PE/BR blend, which is approximately 10 times higher than that of the pure BR. Morphological study demonstrates that the PE forms elongated microdomains finely dispersed in the BR matrix when its content is over 30 wt%, which corresponds to the remarkably enhanced mechanical properties. According to the results, reinforcement mechanism of PE toward BR dependent on the microstructure has been discussed and two different mechanisms have been proposed.     

Rheology, morphology and mechanical properties of polyethylene/ethylene vinyl acetate copolymer (PE/EVA) blends

Rheology, morphology and mechanical properties of binary PE and EVA blends together with their thermal behavior were studied. The results of rheological studies showed that, for given PE and EVA, the interfacial interaction in PE-rich blends is higher than EVA-rich blends, which in turn led to finer and well-distributed morphology in PE-rich blends. Using two different models, the phase inversion composition was predicted to be in 45 and 47 wt% of the PE phase. This was justified by morphological studies, where a clear co-continuous morphology for 50/50 blend was observed. The tensile strength for PE-rich blends showed positive deviation from mixing rule, whereas the 50/50 blend and EVA-rich blends displayed negative deviation. These results were in a good agreement with the results of viscoelastic behavior of the blends. The elongation at break was found to follow the same trend as tensile strength except for 90/10 PE/EVA blend. The latter was explained in terms of the effect of higher co-crystallization in 90/10 composition, which increased the tensile strength and decreased the elongation at break in this composition. The results of thermal behavior of the blends indicated that the melting temperatures of PE and EVA decrease and increase, respectively, due to the dilution effect of EVA on PE and nucleation effect of PE on EVA.     

Effect of epoxidized sunflower oil on polylactic acid properties

Epoxidized sunflower oil (ESO) was utilized as a plasticizer for polylactic acid (PLA) using chloroform as a solvent by a solution casting process at various ratios of PLA to ESO. Fourier-transform infrared (FTIR) spectroscopy was used to identify the functional groups of PLA, ESO, and PLA/ESO blends. Thermal stability and mechanical and morphological properties of the blends were investigated by thermogravimetric analysis, tensile property measurements, and scanning electron microscopy technique, respectively. The FTIR spectra indicate that there are some molecular interactions by intermolecular hydrogen bonding between PLA and ESO. PLA/ESO blends show high thermal stability and significant improvement of mechanical properties compared with pure PLA. The highest elongation at break was obtained when the ratio of the PLA/ESO blend was 80/20. Morphological results of PLA/ESO blends show that ESO was well miscible with PLA.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Preparation of gelatin/poly(vinyl alcohol) film modified by methyl methacrylate and gamma irradiation

The properties of gelatin–polyvinyl alcohol (G–PVA) blend films were improved by methyl methacrylate (MMA) and γ irradiation for a practical viewpoint. The films were prepared by the casting method, modified by glycerol and MMA monomer, and their mechanical properties were also studied. The gelatin-based films were successfully prepared using γ irradiation (3.1 kGy) and gelatin: PVA = 97:3 (w/w) as optimized. Tensile properties of the films were studied and thermal properties of the films were characterized by thermogravimetric analysis and dynamic mechanical analysis pointed out that MMA treated both gelatin films, and G–PVA blend films showed less thermal degradation than untreated films. In addition, structural and morphological features of the gelatin-based films were examined by Fourier transform infrared and scanning electron microscopy, respectively. The ultimate results of the present study showed remarkable enhancement in tensile properties (> 40%) and a reduction in elongation at break of the films, thanks to the MMA addition and γ irradiation.     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Stereocomplexation and mechanical properties of polylactide-<Emphasis Type="Italic">b</Emphasis>-poly(propylene glycol)-<Emphasis Type="Italic">b</Emphasis>-polylactide blend films: Effects of polylactide block length and blend ratio

In the present work, poly(propylene glycol) (PPG) was block copolymerized to form polylactide-poly(propylene glycol)-polylactide (PL-PPG-PL) triblock copolymers for preparing flexible stereocomplex PL (scPL) blend films. The scPL blend films were prepared by solution blending of poly(L-lactide)-PPG-poly(L-lactide) (PLL-PPG-PLL) and poly(D-lactide)- PPG-poly(D-lactide) (PDL-PPG-PDL) triblock copolymers before film casting. The influences of PL end-block lengths (2 × 10⁴ and 4 × 10⁴ g/mol) and blend ratios (75/25, 50/50 and 25/75 W/W) on the stereocomplexation and mechanical properties of the blend films were evaluated. From DSC and WAXD results, the 50/50 blend films had complete stereocomplexation. Phase separation between the scPL and PPG phases was not observed from their SEM images. The tensile stress and elongation at break increased with the sterecomplex crystallinities and PL end-block lengths. The PPG middle-blocks enhanced elongation at break of the scPL films. The results showed that the PL-PPG-PL triblock structures did not affect stereocomplexation of the PLL/PDL block blending. In conclusion, the phase compatibility and flexibility of the scPL films were improved by PPG block copolymerization.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

Blend films of natural wool and cellulose prepared from an ionic liquid

Natural wool/cellulose blends were prepared in an ionic liquid green solvent, 1-butyl-3-methylimidazolium chloride (BMIMCl) and the films were formed subsequently from the coagulated solutions. The wool/cellulose blend films show significant improvement in thermal stability compared to the coagulated wool and cellulose. Moreover, the blend films exhibited an increasing trend of tensile strength with increase in cellulose content in the blends which could be used for the development of wool-based materials with improved mechanical properties, and the elongations of the blends were considerably improved with respect to the coagulated films of wool and cellulose. It was found that there was hydrogen bonding interaction between hydroxyl groups of wool and cellulose in the coagulated wool/cellulose blends as determined by Fourier transform infrared (FTIR) spectroscopy. The ionic liquid was completely recycled with high yield and purity after the blend film was prepared. This work presents a green processing route for development of novel renewable blended materials from natural resource with improved properties.     

Gamma radiation curing of nitrile rubber/high density polyethylene blends

Nitrile butadiene rubber (NBR) was mixed with high density polyethylene (HDPE) thermoplastics with different ratio namely (100/20), (100/40), (100/60) and (100/80). The obtained blends were subjected to gamma irradiation with varying dose from 50 to 250 kGy. The induced crosslinking and hence the improvement in the different properties were followed up as a function of irradiation dose. Mechanical properties as tensile strength, tensile modulus at 50 % elongation, elongation at break percent, permanent set and hardness were carried out as a function of irradiation dose and blend ratio. Moreover, physical properties namely, gel fraction % and swelling number were found to improve with the increase of irradiation dose up to 250 kGy and with the increase of the content of HDPE in blend. Moreover, presence of NBR enhances the shrinking properties of the obtained blend which can be used as a good heat shrinkable material.     

Effect of Electron Beam Irradiation on the Properties of High Styrene Rubber/Styrene Butadiene Rubber Blends

High styrene rubber (HSR)/styrene butadiene rubber (SBR) blends at different ratios were exposed to various doses of electron beam irradiation. The effect of irradiation dose and blend ratios on the mechanical properties and shape memory characteristics in terms of strain fixation) rate (R_f) and strain recovery rate (R_r) was investigated. The results revealed that rich styrene blends displayed higher tensile strength and hardness than low styrene content blends at all irradiation doses. However, elongation at break, and toughness were lower for rich styrene content. Also, it was observed that for most specimens, the tensile strength, elongation at break and hardness increases up to100 kGy. Increasing irradiation doses resulted in slight deterioration in some mechanical properties only for low styrene content at150 kGy. According to the normalized tensile stress at 25% elongation, it was found that the contribution of irradiation in enhancing the mechanical properties is higher for rich butadiene blends. On the other hand, it was observed that rich styrene content blends possess higher R_f and R_r at all the irradiation doses and stretching temperatures. However, the increase of irradiation dose decreases R_f values; the extent of this decrease depends on the blend ratios. Conversely, for all blends, R_r were increased by increasing irradiation dose and styrene content ratios.