Effect of copper source on the structure–activity of CuAl2O4 spinel catalysts for CO hydrogenation

Due to the complexity of the structure–activity relationship of the CuAl₂O₄ spinel catalyst, optimization of the catalyst structure is a great challenge. In this paper, three different CuAl₂O₄ spinel catalysts were prepared by the solid-phase method using copper hydroxide, copper nitrate, and copper oxide as the copper source, respectively, to study the difference in the structure of CuAl₂O₄ spinel catalysts induced by the raw materials and the catalytic behavior for CO hydrogenation. The structure of CuAl₂O₄ spinel catalyst was characterized by XRD, BET, SEM, TEM, H₂-TPR and XPS. The activity of CO hydrogenation over the CuAl₂O₄ spinel catalyst without pre-reduction was evaluated in the slurry reactor. The results demonstrated that different copper sources had obvious influence on the CuAl₂O₄ spinel texture properties, surface enrichment degree, as well as decomposition and reduction ability, which further regulated the ratio of Cu⁺/Cu⁰ and thus affected the catalytic performance, especially the alcohol distribution. The CuAl₂O₄ spinel, employing copper hydroxide as the copper source, showed better selectivity of C₂₊OH, which was assigned to a higher ratio of Cu⁺/Cu⁰, along with larger pore size and pore volume. Moreover, the synergistic effect between Cu⁰ and γ-Al₂O₃ improved the selectivity of dimethyl ether.     

Diffusion of linear paraffins in silicalite studied by the ZLC method in the presence of CO2

The diffusion behavior of C₄–C₁₀ n-alkanes in silicalite-1 has been investigated by using the Zero Length Column method. The diffusivities derived from measurements at different purge rates with different purge gases confirming intracrystalline diffusion control. Data are compared with results reported in the literature for MFI zeolites. The diffusivities were found to be consistent and agree well with data previous obtained by ZLC. However, these data showed a remarkable disagreement with other reported techniques (PFG-NMR, QENS and Permeation). The eventual influence of carbon dioxide (CO₂) adsorption on diffusion properties of n-alkanes in silicalite was also investigated. For this purpose, a series of experiments was performed involving hydrocarbons mixed with CO₂. Data were obtained at 303 K and flow rates between 20 and 80 mL/min. The presence of CO₂ does not seem to influence the intracrystalline transport rate of the investigated light hydrocarbons (n-C₄ and n-C₆). On the other hand, the situation for n-C₈ and n-C₁₀ is more complex. The diffusivity values are higher compared to the previously reported values.     

beta-peptides as catalysts: poly-beta-leucine as a catalyst for the Juliá-Colonna asymmetric epoxidation of enones

Poly-beta-leucines have been evaluated as catalysts for the Juliá-Colonna asymmetric epoxidation of enones; the beta 3-isomer was found to be an effective catalyst for the epoxidation of chalcone (70% ee) and some analogues.     

WO3–SiO2 nanomaterials synthesized using a novel template-free method in supercritical CO2 as heterogeneous catalysts for epoxidation with H2O2

A series of tungsten oxide-silica (WO₃–SiO₂) composite nanomaterials were synthesized through a novel, template-free sol-gel method, in which supercritical-CO₂ (scCO₂) was utilized as synthesis medium. The efficacy of the synthesis method stems from a tailored reactor design that allows the contact of the reactants only in the presence of scCO₂. Selected synthetic parameters were screened with the purpose of enhancing the performance of the resulting materials as heterogeneous catalysts in epoxidation reactions with H₂O₂ as environmentally friendly oxidant. A cyclooctene conversion of 73% with epoxide selectivity of > 99% was achieved over the best WO₃–SiO₂ catalyst under mild reaction conditions (80 °C), equimolar H₂O₂ amount (1:1) and low WO₃ loading (~2.5 wt%). The turnover number achieved with this catalyst (TON = 328), is significantly higher than that of a WO₃–SiO₂ prepared via a similar sol-gel route but without supercritical CO₂, and that of commercial WO₃. A thorough characterization with a combination of techniques (ICP-OES, N₂-physisorption, XRD, TEM, STEM-EDX, SEM-EDX, FT-IR and Raman spectroscopy, XPS, TGA and FT-IR analysis of adsorbed pyridine) allowed correlating the physicochemical properties of the WO₃–SiO₂ nanomaterials with their catalytic performance. The high catalytic activity was attributed to: (i) the very high surface area (892 m²/g) and (ii) good dispersion of the W species acting as Lewis acid sites, which were both brought about by the synthesis in supercritical CO₂, and (iii) the relatively low hydrophilicity, which was tuned by optimizing the tetramethyl orthosilicate concentration and the amount of basic solution used in the synthesis of the materials. Our optimum catalyst was also tested in the reaction of cyclohexene with H₂O₂, resulting in cyclohexane diol as main product due to the presence of strong Brønsted acid sites in the catalyst, whereas the reaction with limonene yielded the internal epoxide as the major product and the corresponding diol as side product. Importantly, the catalyst did not show leaching and could be reused in five consecutive runs without any decrease in activity.     

Heterocyclization of β,γ-dichloro ketones as a method for the synthesis of furan derivatives

Dichloro ketones obtained from acyl chlorides and allyl or -methylallyl chloride undergo spontaneous cyclization to give 2-alkyl- and 2,4-dialkylfurans when they are heated; the intermediates in the case of 2,3-dichloropropene split out a molecule of hydrogen chloride to give 3,4-dichloro-2-butenones.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 3, pp. 313–319, March, 1992.     

Platinum–tin complexes as catalysts for the anodic oxidation of borohydride

Platinum–tin complexes were prepared by the reduction of Pt(IV) with Sn(II) in HCl media and studied by light absorption spectrometry, X-ray photoelectron spectroscopy (XPS), and electron microscopy. The formation of three complexes, H₃[Pt(SnCl₃)₅], H₂[Pt(SnCl₃)₂Cl₂], and H₂[Pt₃(SnCl₃)₈], depending on HCl and SnCl₂ concentrations, has been shown. The glassy carbon (GC) electrode modified in the complexes solutions was found to be an electrocatalyst for borohydride oxidation in a 1.0-M NaOH solution. Comparison of BH₄ ⁻ electrooxidation on Pt and on GC modified with platinum–tin complexes has shown that catalytic hydrolysis of BH₄ ⁻ did not proceed in the latter case in contrast to its oxidation on the Pt electrode, and only direct BH₄ ⁻ oxidation has been observed in the positive potentials scan. The activity of Pt–Sn complexes for BH₄ ⁻ oxidation changes with time and eventually decreases due to Sn(II), bound in the complex with Pt(II), oxidation by atmospheric oxygen. The complexes may be renewed by addition of missing amounts of SnCl₂ and HCl.     

Reaction of the dimethoxyaminyl radical with tertiary nitrosoalkanes as a method for the preparation of N-alkyl-N′-methoxydiazene N-oxides

The reaction of the dimethoxyaminyl radical with functionally substituted nitrosoalkanes (2) in a 2:1 ratio at 20°C gives the corresponding N-alkyl-N-methoxydiazene N-oxides (3) as a single isomer in preparative yields.N. N. Semenov Institute of Chemical Physics, Russian Academy of Sciences, 117913 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 10, pp. 2443–2445, October, 1992.     

Studies of copper (Ⅱ) complexes as catalysts for the hydrolysis of DNA

Hydrolysis of DNA is an important enzymatic reaction , but it is exceedingly difficult to mimic in the laboratory because of the stability of hydrolysis of DNA. In this paper, the cleavage activity of complexes formed between Cu(Ⅱ) and four different amino acid or amino acid methyl ester on DNA is studied by gel elec-trophoresis. It is found that DNA could be cleaved by Cu(Ⅱ)-L-His and Cu(Ⅱ)-L-His methyl ester complexes and the efficiency of cleavage is largely dependent on the metal ion-to-ligand ratio. Further experiments show that the cleavage of DNA mediated by Cu(Ⅱ)-L-His complexes occurs via a hydrolytic mechanism and the active chemical species that affects DNA cleavage is proposed to be MI2H and ML2H22 .     

A study on the structure and catalytic performance of ZnxCu1−xAl2O4 catalysts synthesized by the solution combustion method for the esterification reaction

A Zn_xCu_1−xAl₂O₄ catalyst was prepared via the microwave-assisted solution combustion method (MSC). This method presents a fast procedure for industrial scale catalyst preparation. The physicochemical properties of the fabricated catalyst were characterized using XRD, FTIR, BET, SEM and TEM analyses. The catalytic performance through the esterification reaction was examined under the following conditions: reaction temperature = 180 °C, catalyst concentration = 3% (w/w), molar ratio of oleic acid to methanol = 9 and reaction time = 6 h. XRD results showed that loading both zinc and copper oxides on alumina at a ratio of amounts that were nearly the same resulted in decreased crystalline size and well-dispersed copper-alumina and zinc-alumina crystals. Moreover, the mean pore diameter of the sample was increased by simultaneous loading of zinc and copper oxides on alumina that enhanced permeation of the reactants within pores and increased the interaction of the reactant with the catalyst active sites. The catalyst showed minimum tendency towards adsorbing moisture from air, which was attributed to it having less atoms on the surface through which binding with H₂O molecules takes place. The highest level of activity in the esterification reaction (96.9%) was obtained at the optimum ratio of the Zn:Cu molar ratio, identified to be 2:3. The sample particles ranged from 10 to 30 nm in size, without agglomeration.     

N-methyl-2-pyrrolidonium-based Brönsted-Lewis acidic ionic liquids as catalysts for the hydrolysis of cellulose

We experimentally studied the catalytic performances of a series of Br?nsted-Lewis acidic N-methyl-2-pyrrolidonium metal chlorides([Hnmp]Cl/MCl_x, where M=Fe, Zn, Al, or Cu) for the hydrolysis of microcrystalline cellulose(MCC) and cotton to produce reducing sugar. A variety of factors, such as temperature, time, ionic liquid(IL) species, IL dosage, and the concentration of the metal chloride were investigated. [Hnmp]Cl/FeCl_3 presented the best hydrolysis performance, affording a 98.8% yield of total reducing sugar from MCC(1 h, 100 °C, 0.1 g MCC, 0.2 g acidic IL, 2.0 g [Bmim]Cl as solvent), which is better than or comparable to results previously obtained with other –SO_3H functionalized acidic ILs. The hydrolysis performances of [Hnmp]Cl/MClx were rationalized using density functional theory calculations, which indicated that interactions between the metal chlorides and the cellulose, including charge-transfer interactions are important in the hydrolysis of cellulose and degradation of glucose. This work shows that Br?nsted-Lewis acidic ILs are potential catalysts for the hydrolysis of cellulose to produce sugar.     

Algorithm for the calculation of the electronic structure of molecules by the expanded Hückel method

An algorithm is described for the calculation of quantum-chemical characteristics of molecules by the expanded Hückel method. The method for the calculation of the complete overlap matrix of Slater atomic orbitals of type ns, np, and nd was modified.     

The characterisation and evaluation of activated carbon in a cigarette filter

Cigarette smoke is an ever changing and extremely complex mixture of over 5000 chemicals. When the cigarette burns, thousands of chemical substances are generated, and these are distributed between the gas phase and the particles which constitute the smoke aerosol. Activated carbon when used in a filter can selectively remove a number of the vapour phase compounds to varying degrees of efficiency. Carbons of different activities (50–60% CTC and 90–100% CTC) have been characterised using nitrogen adsorption and also the sorption of a number of different vapours with different properties, using a dynamic gravimetric adsorption technique. Surface areas, pore volumes, diffusivities and heats of adsorption were calculated using nitrogen, benzene, heptane, ethyl acetate and water as the probe molecules. Smoke chemistries were measured using a screening approach on the characterised carbons as filter additives. It was seen that the higher activity carbon results in increased retention in the majority of the measured vapour phase smoke constituents.     

Adsorption properties of BEA zeolites and their aluminum phosphate extrudates for purification of isomaltose

The disaccharide isomaltose is produced via an enzymatic reaction and is adsorbed to BEA zeolite. This reaction integrated adsorption can be achieved as fluidized bed as well as fixed bed. We investigated isotherms, adsorption enthalpies and sorption kinetics of BEA zeolite and extrudates with a novel aluminum phosphate sintermatrix. These extrudates contain 50% (w/w) of BEA 150 zeolites (Si/Al = 75) as primary crystals. BET-surface for extrudates is 245 m²⋅g⁻¹ and 487 m²⋅g⁻¹ for zeolite. Extrudates show a monomodal macropore structure with a maximum at 90 nm. All isotherms show a type I shape. For lower equilibrium concentrations, which occur during the enzymatic reaction, Henry’s law is applied and compared to a Langmuir model. Adsorption equilibrium constant K _i,L calculated from Langmuir for extrudates at 4 °C is 64.7 mL⋅g⁻¹ and more than twice as high as obtained from Henry’s law with K _i is 26.8 mL⋅g⁻¹. Adsorption on extrudates at 4 °C is much stronger than on zeolite crystals where the Henry coefficient K _i is 17.1 mL⋅g⁻¹. Adsorption enthalpy Δh _Ad calculated from van’t Hoff plot with the Henry equation is −44.3 kJ⋅mol⁻¹ for extrudates and −29.6 kJ⋅mol⁻¹ for zeolite crystals. Finally, the kinetics for ad- and desorption were calculated from the initial slope. The diffusion rate for ad- and desorption on extrudates were in the same range while adsorption on zeolites is three orders of magnitudes faster than desorption.     

Tetranuclear CuII Cluster as the Ten Node Building Unit for the Construction of a Metal–Organic Framework for Efficient C2H2/CO2 Separation

Rational design of high nuclear copper cluster-based metal–organic frameworks has not been established yet. Herein, we report a novel MOF ( FJU-112 ) with the ten-connected tetranuclear copper cluster [Cu₄(PO₃)₂(μ₂-H₂O)₂(CO₂)₄] as the node which was capped by the deprotonated organic ligand of H₄L (3,5-Dicarboxyphenylphosphonic acid). With BPE (1,2-Bis(4-pyridyl)ethane) as the pore partitioner, the pore spaces in the structure of FJU-112 were divided into several smaller cages and smaller windows for efficient gas adsorption and separation. FJU-112 exhibits a high separation performance for the C₂H₂/CO₂ separation, which were established by the temperature-dependent sorption isotherms and further confirmed by the lab-scale dynamic breakthrough experiments. The grand canonical Monte Carlo simulations (GCMC) studies show that its high C₂H₂/CO₂ separation performance is contributed to the strong π-complexation interactions between the C₂H₂ molecules and framework pore surfaces, leading to its more C₂H₂ uptakes over CO₂ molecules.     

Clay pigment structure characterisation as a guide for provenance determination—a comparison between laboratory powder micro-XRD and synchrotron radiation XRD

Application of X-ray diffraction (XRD)-based techniques in the analysis of painted artworks is not only beneficial for indisputable identification of crystal constituents in colour layers, but it can also bring insight in material crystal structure, which can be affected by their geological formation, manufacturing procedure or secondary changes. This knowledge might be helpful for art historic evaluation of an artwork as well as for its conservation. By way of example of kaolinite, we show that classification of its crystal structure order based on XRD data is useful for estimation of its provenance. We found kaolinite in the preparation layer of a Gothic wall painting in a Czech church situated near Karlovy Vary, where there are important kaolin deposits. Comparing reference kaolin materials from eight various Czech deposits, we found that these can be differentiated just according to the kaolinite crystallinity. Within this study, we compared laboratory powder X-ray micro-diffraction (micro-XRD) with synchrotron radiation X-ray diffraction analysing the same real sample. We found that both techniques led to the same results.     

Ionic liquids as efficient phase-transfer catalysts for the solid base-promoted monoalkylation of diethyl malonate

Ionic liquids （ILs） based on 1,3-dialkylimidazolium and tetraalkylammonium cations were employed as a series of efficient, environmentally benign phase-transfer catalysts （PTCs） for the base-promoted monoalkylation of diethyl malonate. The influence of various heterogeneous bases on yields was studied. Good yields and high selectivity were obtained. Solvent-free, mild reaction condition, short reaction time, and easy purification were the merits of this method. The catalytic system （IL-hase） could also be recycled after the extraction of products with ether.     

Investigation of the effect of cobalt on the Ni–Al2O3 catalyst prepared by the mechanochemical method for CO2 methanation

Research on Chemical Intermediates - Various Ni–Co catalysts supported on alumina were produced by the mechanochemical technique and applied to CO2 Methanation. X-ray diffraction,...     

NaBrO3/NaHSO4 · H2O as a Versatile Reagent System for the Oxidation of Benzylic Alcohols and Aldehydes

The oxidation of benzylic alcohols and aldehydes by NaBrO₃ is efficiently promoted in the presence of NaHSO₄ · H₂O. All reactions were performed under mild and completely heterogeneous conditions in good to high yields.     

Do the hemeproteins behave as a dissipative structure?

Continuing the search for a broader interpretation of hemeprotein behavior, we give preliminary results showing that there are electric and dynamic couplings between the heme group and amino acid residues within the protein matrix. EPR and X-ray absorption spectroscopy studies on azidometmyoglobin show that both magnetic and geometric properties of Fe N₃ evolve in the same nonlinear way as pH is increased and are tightly correlated to the strains on the helical segments of the protein. Flash photolysis of carbon monoxide hemoglobin, in the presence of ethanol or formamide, allows the study of cosolvent effects on geminate and nongeminate recombinations of the CO ligand trapped within the protein matrix. Data clearly show that cosolvents alter the statistic fluctuations of the protein, as well as the ligand partition between different protein matrix domains. From these studies, it is concluded that alterations occurring at particular sites give way to global protein perturbations. Then, each perturbated protein domain—binding site included—evolves with its own sensitivity to a new metastable state of the protein. The amplification of the initial perturbation which—instead of regressing—progressively propagates through the whole macromolecule is typical of a dissipative structure in the Prigogine sense. Biological properties of hemeproteins largely involve the surrounding solvent, via permanent or temporary exchanges of water molecules, protons, and small ligands. These fluxes along with their entropic corollary are not quite compatible with a conservative system. These works present the current trends developed in our laboratory in association with the European network “The Dynamics of Protein Structure.” In this framework, our laboratory collaborates with Dr. W. Doster and T. Kleinert (Munich, Germany) for the CO recombination studies in hemoglobin and with Dr. J. Hutterman (Homburg, Germany) and Drs. A. Bianconi and S. Della Longa (Rome and L'Aquila, Italy) for the magnetic and geometric properties of the myoglobin iron site. © 1996 John Wiley & Sons, Inc.     

Adsorption of arsenic (V) from a water solution onto a surfactant-modified zeolite

In this study a surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium (HDTMA) bromide on a clinoptilolite. The adsorption of the surfactant modified the surface properties of the clinoptilolite and enhanced the anionic capacity of the SMZ. The adsorption equilibrium data of As(V) from the water solution on the SMZ were obtained in a batch adsorber, and the Langmuir isotherm matched the data reasonably well. The As(V) adsorption capacity of the SMZ was 12.5 times greater than that of the clinoptilolite. The adsorption of As(V) on SMZ was mainly due to the interactions between the anionic sites of the SMZ and the As(V) anions in water solution. The adsorption capacity of the SMZ was dependent on the solution pH. The adsorption capacity was increased and decreased by augmenting the pH from 5 to 7 and from 7 to 12, respectively. This unusual behavior was due to the fact that the affinity of the As(V) for the SMZ was dependent on the As(V) species that were present in solution. The adsorption capacity of the SMZ was slightly favored by decreasing the temperature from 25 to 15 °C. The heat of adsorption was estimated to be ΔH _ads=−46.82 KJ/mol, indicating that the adsorption was exothermic and the As(V) was chemisorbed on the SMZ.