Isoconversional kinetics of degradation of polyvinylpyrrolidone used as a matrix for ammonium nitrate stabilization

Thermogravimetric analyzer (TGA) has been applied to measure the kinetics of the thermal degradation of virgin polyvinylpyrrolidone (PVP) and a phase stabilized PVP–ammonium nitrate (AN) material. The PVP–AN samples have been prepared by using 20 wt.% of AN and PVP of three different molecular weights. Virgin PVP undergoes a major mass loss in the region 380–550 °C leaving a small amount of nonvolatile residue. The application of an advanced isoconversional method to the respective degradation process demonstrates that its effective activation energy increases from 70 kJ mol⁻¹ to a plateau value at 250–300 kJ mol⁻¹, which is independent of the molecular weight. The PVP–AN materials lose spontaneously 20% of their mass on heating above the glass transition temperature of the PVP matrix (160–180 °C). After the escape of AN, the remaining PVP matrix degrades in the same temperature region as virgin PVP, however, the effective activation energy of this degradation is 150–200 kJ mol⁻¹.     

Electrochemical properties of polyaniline in p-toluene sulfonic acid solution

Polyaniline was deposited potentiodynamically on a stainless steel substrate in the presence of an inorganic acids (sulfuric acid). The electrochemical characterization of the electrode was carried out by means of cyclic voltammetry and electrochemical impedance spectroscopy in the organic acids (p-toluene sulfonic acid) solution. The results show that polyaniline has a high specific capacitance of 431.8 F g⁻¹ at 1 mV s⁻¹, high coulombic efficiency of 95.6% at 20 mV s⁻¹, and exhibits a high reversibility. This indicates the promising feasibility of the polyaniline used as an electrochemical capacitor material in the electrolyte of p-toluene sulfonic acid solution especially at high charge–discharge process.     

Enhanced tungstate electrochromism via formation of transparent conductive networks

Indium tin oxide (ITO) nanopowder was added to a polymer film containing WO₃ · H₂O particles to enhance electron conductivity and complimentary Li ion kinetics in an electrochromic device. Film conductivity increased dramatically with ITO content, suggesting the formation of conductive ITO networks in the film. The improved electron conductivity leads to a substantial increase of the effective Li⁺ ion diffusion coefficient in the composite film, from 10⁻¹¹ to 10⁻⁹ cm²/s. Electrochromic contrast studies revealed that the presence of the ITO networks leads to enhanced blue/green color contrast.     

Simultaneous determination of chloride, nitrate and sulphate in vegetable samples by single-column ion chromatography

A new ion chromatography method is described for the simultaneous determination of Cl⁻, NO₃⁻ and SO₄²⁻, using a selected eluent 1.3-mM sodium gluconate/1.3-mM borax (pH 8.5). The extraction methods of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables are studied. The determination limits of Cl⁻, NO₃⁻, SO₄²⁻ are 0.17 μg/ml, 0.63 μg/ml and 0.81 μg/ml. The linear ranges are 060 μg/ml, 090 μg/ml and 090 μg/ml. The relative S.D. are <2.5%. The mean recoveries of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables range from 97.0 to 104%.     

Molecular fine structure and transition dipole moment of NO2 using an external cavity quantum cascade laser

Rotational vibrational fine structure and transition dipole moment of NO₂ is measured using Doppler free saturation spectroscopy with an external grating cavity quantum cascade laser (QCL). The QCL wavelength is calibrated using a 310 cm long internally coupled Fabry–Perot interferometer. We obtain a frequency splitting of 139.68 ± 0.06 MHz (0.0047 cm⁻¹) between the spin doublets (17) of 000 → 001 transition of NO₂. The resolution of the QCL based saturation spectrometer is limited by the QCL linewidth of 3.99 MHz ( 0.00013 cm⁻¹) deduced from the half width of the Lamb dips. The Lamb dip spectroscopy is utilized to obtain a vibrational dipole moment of 0.37 Debye for the (17) transitions.     

Reduced N-methyl-pyridylethynyl porphyrins exhibit strong near-IR absorptions

Porphines bearing two N-methyl-4-pyridylethynyl substituent reversibly undergo two one-electron reductions at room temperature. The anion radicals and di-anions show diminished visible bands (450 nm and 600–700 nm) and intense absorptions in the 800-nm and 1100-nm region, respectively. Some of the near-IR bands have extinction coefficients greater than 1.5 × 10⁵ M⁻¹ cm⁻¹.     

Characterization of a 10.3-μm pulsed DFB quantum cascade laser

We have measured the output parameters of a 10.3-μm pulsed distributed-feedback (DFB) quantum cascade (QC) laser manufactured by Alpes Lasers and intended for high-sensitivity detection of ammonia and ethylene. The laser beam was collimated with an AR-coated aspheric ZnSe lens with focal length of 11.6 mm and clear aperture of 16.5 mm. Near- and far-field distributions of the laser emission were recorded with an infrared imaging camera. The fast-and slow-axis laser beam divergences were measured to be 1.2 and 1.4 mrad (FWHM), respectively. The divergence was found to be increasing with injection current. An air-spaced Fabry–Perot interferometer with free spectral range of 0.05 cm⁻¹ was used to measure the frequency tuning rates of the laser. The laser was tuned by either heat sink temperature, injection current or pulse repetition rate with rates of −8 × 10⁻² cm⁻¹ K⁻¹, −7 × 10⁻² cm⁻¹ A⁻¹ and −9 × 10⁻⁴ cm⁻¹ kHz⁻¹, respectively. The laser frequency decreased linearly with a rate of 10⁻² cm⁻¹ ns⁻¹ (300 MHz ns⁻¹) for laser pulses varied from 10 to 50 ns, and the frequency chirp rate was found to decrease for longer laser pulses.     

Interaction and photodynamic activity of cationic porphyrin derivatives bearing different patterns of charge distribution with GMP and DNA

The interaction of amphiphilic cationic porphyrins, containing different patterns of meso-substitution by 4-(3-N,N,N-trimethylammoniumpropoxy)phenyl (A) and 4-(trifluoromethyl)phenyl (B) groups, with guanosine 5′-monophosphate (GMP) and calf thymus DNA have been studied by optical methods in phosphate buffer solution. The properties of these synthetic porphyrins were compared with those of representative standard of anionic 5,10,15,20-tetra(4-sulphonatophenyl)porphyrin (TPPS₄⁴⁻) and cationic 5,10,15,20-tetra(4-N,N,N-trimethylammonium phenyl)porphyrin (TMAP⁴⁺). Stable complexes with GMP were found for cationic porphyrins, except for monocationic AB₃⁺. The binding constant (K_GMP  10⁴ M⁻¹) follows the order: A₃B³⁺  ABAB²⁺ > A₄⁴⁺  TMAP⁴⁺. Also, interaction with DNA was observed for all evaluated cationic porphyrins. For these related cationic porphyrins, the binding constant (K_DNA  10⁵ M⁻¹) increases with the number of cationic charges. On the other hand, the photodynamic activity of porphyrins was analyzed in solution of GMP and DNA. Monocationic AB₃⁺ is a less effective sensitizer to oxidize GMP in comparison with the other cationic porphyrins, in agreement with the lack of detected interaction with this nucleotide. The electrophoretic analysis of DNA indicates that photocleavage takes place when the samples are exposed to photoexcited tricationic and tetracationic porphyrins. In the presence of sodium azide the DNA decomposition was diminished. Also, reduction in the DNA photocleavage was observed under anoxic condition, indicating that oxygen is essential for DNA photocleavage sensitized by these cationic porphyrins. In addition, an increase in DNA degradation was not observed in deuteriated water. Therefore, an important contribution of type I photoreaction processes could be occurring in the DNA photodamage sensitized by these cationic porphyrins. These results provide a better understanding of the characteristics needed for sensitizers to produce efficient DNA photocleavage.     

Vibrational satellite of Na(3d ← 3s) dipole-forbidden transition in Na/CF4 mixture

Excitation spectra of Na fluorescence in mixtures with CF₄ display a new band shifted by the energy of one-vibrational quantum of the IR active ν₃-mode of CF₄ (1281 cm⁻¹) from Na 3d states. This band is attributed to a Na(3s)CF₄(ν₃ = 0) → Na(3d)CF₄(ν₃ = 1) transition and its intensity is explained by coupling with Na(4p)CF₄(v₃ = 0) resonance state which lies  180 cm⁻¹ below in energy. An analogous satellite of the Na 6p state combined with the same vibration and lying close to the Na 7p state is reported and discussed.     

Solvent effect on the blue shifted weakly H-bound F3 CH…FCD3 complex

Solvent effect on the ν^c frequency of CH stretching vibration of the blue shifted F₃CH…FCD₃ complex has been studied in liquefied N₂, CO, Ar, Kr and Xe. In the case of Xe, the spectroscopic measurements have also been extended to the solid state. It was found that the ν^c position of the complex in the solutions studied lowers with respect to the value in the gas phase. In liquid Xe, characterized by the largest permittivity, this effect reaches its maximum value of −14.5 cm⁻¹. The ν^c frequency begins to grow again just below the freezing point of Xe, where a noticeable (15%) increase of the density of Xe occurs. The experimental results obtained for the liquid phase have been analyzed in the framework of the Onsager-like reaction field model and Polarizable Continuum Model (PCM) implemented into a standard Gaussian 98 Program.     

Photodegradation of poly(neopentyl isophthalate) part I: Laboratory and outdoor conditions

In this paper the mechanisms of photodegradation of poly(neopentyl isophthalate) (PNI) in laboratory (Suntest XXL+, λ > 300 nm) and outdoor conditions are compared. Changes in the chemical composition were studied with ATR-FTIR, SEC and MALDI-ToF MS. Furthermore, the results were compared with data presented in our previous paper on PNI coatings that were aged in the UVACUBE (λ > 254 nm). Two main aspects of photodegradation of PNI are addressed in the present paper: the influence of different wavelengths and the comparison of laboratory and outdoor exposure regarding the mechanism of degradation. Under short (λ > 254 nm) and long (λ > 300 nm) wavelength irradiation similar products of degradation are formed. However, the presence of short wavelength radiation dramatically accelerates the overall rate of photodegradation of PNI. UV light absorption calculations confirm this experimentally found acceleration. Exposure of PNI in laboratory and outdoor conditions, both with wavelengths λ > 300 nm resulted in similar degradation products in the initial stage of ageing.     

Existence of clathrate-like structures in supercooled water: X-ray diffraction evidence

X-ray diffraction study of supercooled water has been performed using an imaging-plate X-ray detector down to −15 °C. The peak at 10.8 Å, which grows with decreasing temperature, in the radial distribution function {D(r) − 4πr²ρ₀} indicates the existence of clathrate-like structures in supercooled water. It is suggested that anomalous properties of water, which become more pronounced at low temperatures, are closely linked to the development of clathrate-like structures in water at low temperatures.     

Synthesis, characterization and radiolytic properties of bis(oxalato)borate containing ionic liquids

Previously unreported bis(oxalato)borate (BOB) ionic liquids (ILs) containing imidazolium, pyridinium, and pyrrolidinium cations were prepared from the corresponding halide salts by reaction with sodium bis(oxalato)borate (NaBOB), and their properties are reported. Pulse radiolysis experiments revealed that the BOB anion scavenges solvated electrons with rate constants of 3×10⁸ M⁻¹ s⁻¹ in the ionic liquid C₄mpyrr NTf₂ and 2.8×10⁷ M⁻¹ s⁻¹ in water. This reactivity indicates that BOB ILs may be too sensitive to be used as neat solvents for nuclear separations processes in high radiation fields but may still be useful for preventing criticality while processing relatively “cold” fissile actinides.     

Gas-phase reactions of halogenated radical carbene anions with sulfur and oxygen containing species

The reactivities of mono- and dihalocarbene anions (CHCl⁻, CHBr⁻, CF₂⁻, CCl₂⁻, and CBrCl⁻) were studied using a tandem flowing afterglow-selected ion flow tube instrument. Reaction rate constants and product branching ratios are reported for the reactions of these carbene anions with six neutral reagents (CS₂, COS, CO₂, O₂, CO, and N₂O). These anions were found to demonstrate diverse chemistry as illustrated by formation of multiple product ions and by the observed reaction trends. The reactions of CHCl⁻ and CHBr⁻ occur with similar efficiencies and reactivity patterns. Substitution of a Cl atom for an H atom to form CCl₂⁻ and CBrCl⁻ decreases the rate constants; these two anions react with similar efficiencies and reactivity trends. The CF₂⁻ anion displays remarkably different reactivity; these differences are discussed in terms of its lower electron binding energy and the effect of the electronegative fluorine substituents. The results presented here are compared to the reactivity of the CH₂⁻ anion, which has previously been reported.     

Dual electrochemical microsensor for simultaneous measurements of nitric oxide and oxygen: Fabrication and characterization

A planar-type amperometric dual microsensor was developed for the simultaneous measurement of the nitric oxide (NO) and oxygen (O₂) concentrations. The sensor (overall diameter = 500 μm) consisted of a dual working electrode (WE) containing two platinized platinum microdisks (25 μm diameter, WE1, WE2, distance between two disks > 330 μm) and a Ag/AgCl wire reference electrode covered with an expanded poly(tetrafluoroethylene) gas-permeable membrane. The differentiation and concurrent measurements of NO and O₂ were obtained successfully using two sensing WEs with different applied potentials (+0.75 V for WE1 and −0.4 V for WE2). Cross-talk between WE1 and WE2 was eliminated with an optimized internal solution composition. Linear dynamic range, selectivity, sensitivity, detection limit (<5 nM for NO; <500 nM for O₂), and stability (>50 h) were evaluated.     

Charge transport modulation of silicon nanowire by O2 plasma

The modification of the electrical characteristics of field-effect transistors (FETs) with channels composed of n- or p-type silicon nanowires (SiNWs) by oxygen plasma treatment is investigated in this study. The SiNWs obtained from silicon bulk wafers are <111> surface-oriented and their doping concentrations are 10²¹ and 10¹⁷ cm⁻³ for the n- and p-type SiNWs, respectively. After the back-gate SiNWFETs were subjected to oxygen plasma treatment, the magnitude of the drain current of the n-type SiNWs was decreased, whereas that of the p-type SiNWs was increased, while the gate-dependent characteristics of both of types of SiNWs were improved. The changes in the electrical characteristics are due to the adsorption of oxygen ions on the surface of the SiNWs. To verify the effect of the oxygen ions, the SiNWFETs were kept in a vacuum for 24 h whereupon their electrical characteristics tended to revert to their inherent state.     

Role of electrolytes in the preparation of nanoparticles via the emulsion polymerization of vinyl pivalate

By controlling both the kind of ion and the ionic strength of electrolytes in an emulsion polymerization system of vinyl pivalate containing about 1% sodium lauryl sulfate as a surfactant, nanoparticles of polyvinylpivalate having a diameter of about 25 nm were successfully prepared. The use of high concentrations of lithium chloride and lithium sulfate (1.0 mol L⁻¹) prevented the nanoparticles from aggregating and produced nanoparticles sizes of 25–50 nm. Ammonium acetate and sodium acetate, on the other hand, accelerated the aggregate of the nanoparticles. These phenomena were examined in detail and found to be similar to the Hofmeister phenomena and the combination rule proposed by Craig et al.     

Photoacoustic infrared spectroscopy of polymer beads

Photoacoustic (PA) spectra of four types of polymer resin beads, ranging in size from 35 to 150 μm, were acquired using a Fourier transform infrared spectrometer capable of both rapid- and step-scan mirror movement. Thermal diffusion lengths were on the order of the particle sizes of the beads. The PA magnitude spectra were similar to absorption spectra; both positive- and negative-going features occurred in the phase spectra. The frequency dependences of the total PA intensities of the polymer resins and carbon black differed by a factor of about f^−0.30. The intensities of the weak bands in the ratioed spectra (resin beads/carbon black) displayed a similar dependence. Partial saturation caused a more gradual variation for the stronger bands, where the intensity is proportional to f^−0.1–f^−0.2.     

An investigation of the chemiluminescence reaction in the sodium hypochlorite–folic acid–emicarbazide hydrochloride system

A chemiluminescence method for the determination of folic acid by the sodium hypochlorite–folic acid–semicarbazide hydrochloride system with a new flow injection technique has been established. The new method can perform simple, sensitive and rapid determinations of folic acid. The response to the concentration of folic acid, in the range of 1.0×10⁻⁷5.0×10⁻⁵ g/ml, is linear. The relative standard deviation of the method is 2.3% (C_s=4.0×10⁻⁶ g/ml, n=11). The detection limit is 2.7×10⁻⁸ g/ml. This method is suitable for automatic and continuous analysis, and has been successfully tested for the determination of folic acid in a folic acid tablet.     

Effect of high rates of mass transport on oxygen reduction at copper electrodes: Implications for aluminium corrosion

The reduction of oxygen at copper microelectrodes (25 μm diameter) in aqueous solution (pH 7) has been studied under conditions of high mass transport, similar to those experienced by μm sized copper-containing inclusions in aluminium alloys during corrosion. Contrary to previous studies at copper electrodes operating at lower mass transport rates, oxygen reduction limiting currents show an apparent number of electrons which decrease towards 2 as the mass transport rate increases (mass transfer coefficients up to ca. 0.55 cm s⁻¹), rather than a 4-electron process. These new data suggest that the treatment of oxygen reduction as a 4-electron transfer process at micron and smaller-sized copper intermetallics in aluminium alloys may require revision.