Micro-pumping flow system for spectrophotometric determination of anionic surfactants in water

A novel procedure has been developed for spectrophotometric determination of anionic surfactants in water using a solenoid micro-pump as fluid-propulsion device. The proposed method is based on substitution of methyl orange (MO) by anionic surfactants in the formation of an ion-pair with the cetyl pyridine ion (CPC⁺) at pH 5.0. The flow network comprised four solenoid micro-pumps which, under microcomputer control, enabled sample and reagent introduction, and homogenisation in the reaction zone. The system is flexible and simple to operate and control, and sensitive and precise. The analytical plot for the anionic surfactant was linear between 1.43×10^–6 and 1.43×10^–5 mol L^–1 (0.5 to 5.0 mg L^–1; R=0.997, n=5). The relative standard deviation was 0.8% (n=11) for a sample containing 5.74×10^–6 mol L^–1 (2 mg L^–1) surfactant. The limit of detection was 9.76×10^–8 mol L^–1 (0.034 mg L^–1) and the sampling throughput was 60 determinations per hour. The results obtained for washing-water samples were comparable with those obtained by use of the reference method, and no significant differences at the 95% confidence level were observed.     

Determination of phenylglyoxylic acid in urine using a multi-pumping flow system

In this work a simple, fast and fully automated analytical methodology for the spectrophotometric determination of phenylglyoxylic acid is proposed. Phenylglyoxylic acid is a metabolite of styrene that is excreted in urine, being used as an indicator of styrene occupational exposure. The developed procedure was based on the phenylglyoxylic acid ability to inhibit the formation of the peroxovanadium cation produced by the reaction between vanadate and H₂O₂. The analytical process was implemented in a multi-pumping flow system that employs multiple solenoid actuated micro-pumps as the only active components. This enabled the reproducible insertion and efficient mixing of low volumes of sample and reagents as well as the transportation of the sample zone towards detection. Thus an easily controlled, low cost, compact and reliable analytical system was implemented. A linear working range for phenylglyoxylic acid concentrations up to 700?mg?L^?1 (r ^2?=?0.995, n?=?7), was obtained, with a detection limit of 37?mg?L^?1. The system handles about 43 determinations per hour yielding precise results (relative standard deviation?<?5%, n?=?10). The developed methodology was applied to the determination of phenylglyoxylic acid in urine samples and the obtained results were in agreement with those furnished by the comparison method with relative percentage deviations lower than 6.6%.     

A spectrophotometric flow procedure for the determination of cationic surfactants in natural waters using a solenoid micro-pump for fluid propulsion

An automatic flow-analysis procedure for spectrophotometric determination of cationic surfactants in surface water using a solenoid micro-pump for propelling solutions of reagents and sample is described. The proposed method is based on a ternary formation complex between chromazurol S, the Fe(III) ion, and the cationic surfactant. The flow network comprised four solenoid micro-pumps controlled by a microcomputer, which performed the sampling step by loading a reaction coil with sample and reagent solutions and displacing the sample zone through the analytical path. The system is simple, easy to operate, and very flexible, with sufficient sensitivity to determine cationic surfactants in water without any pre-concentration or separation step. After determining the best operational conditions, favourable features such as a linear response between 0.34 and 10.2?mg?L^?1 of surfactant (R?=?0.999), a relative standard deviation of 0.6% (n?=?11) for a sample containing 3.4?mg?L^?1 of surfactant, a detection limit of 0.035?mg?L^?1 of surfactant, and a sampling throughput of 72 determinations per hour were achieved. The system was used to determine cationic surfactant in river-water samples, and recovery values between 91 and 106% were achieved.     

A multi-pumping flow-based procedure with improved sensitivity for the spectrophotometric determination of acid-dissociable cyanide in natural waters

An analytical procedure with improved sensitivity was developed for cyanide determination in natural waters, exploiting the reaction with the complex of Cu(I) with 2,2′-biquinoline 4,4′-dicarboxylic acid (BCA). The flow system was based on the multi-pumping approach and long pathlength spectrophotometry with a flow cell based on a Teflon AF 2400^® liquid core waveguide was exploited to increase sensitivity. A linear response was achieved from 5 to 200 μg L⁻¹, with coefficient of variation of 1.5% (n = 10). The detection limit and the sampling rate were 2 μg L⁻¹ (99.7% confidence level), and 22 h⁻¹, respectively. Per determination, 48 ng of Cu(II), 5 μg of ascorbic acid and 0.9 μg of BCA were consumed. As high as 100 mg L⁻¹ thiocyanate, nitrite or sulfite did not affect cyanide determination. Sulfide did not interfere at concentrations lower than 40 and 200 μg L⁻¹ before or after sample pretreatment with hydrogen peroxide. The results for natural waters samples agreed with those obtained by a fluorimetric flow-based procedure at the 95% confidence level. The proposed procedure is then a reliable, fast and environmentally friendly alternative for cyanide determination in natural waters.     

Urease–glutamic dehydrogenase biosensor for screening heavy metals in water and soil samples

A screen-printed three-electrode amperometric biosensor based on urease and the nicotinamide adenine dinucleotide hydrogen (NADH)–glutamic dehydrogenase system was developed and applied to the screening of heavy metals in environmental samples. The development of an amperometric sensor for the monitoring of urease activity was feasible by coupling the urea breakdown reaction catalysed by urease to the reductive ammination of ketoglutarate catalysed by glutamic dehydrogenase (GLDH). The ammonia provided by the urea conversion is required for the conversion of ketoglutarate to glutamate with the concomitant oxidation of the NADH cofactor. NADH oxidation is monitored amperometrically at 0.3 V (vs. Ag/AgCl) after urease immobilization onto the screen-printed three-electrode configuration. Immobilization of urease on the surface of screen-printed electrodes was performed by entrapment in alginate gel and adsorption on the electrode in a nafion film. Low sensitivity to inactivation by metals was recorded after urease entrapment in alginate gel with detection limits of 2.9 and 29.8 mg L^–1 for Hg(II) and Cu(II), respectively. The use of the negatively charged nafion film created a more concentrated environment of cations in proximity to the enzyme, thus enhancing the urease inhibition when compared to gel entrapment. The calculated detection limits were 63.6 and 55.3 g L^–1 for Hg(II) and Cu(II), respectively, and 4.3 mg L^–1 for Cd(II). A significant urease inactivation was recorded in the presence of trace amounts of metals (g L^–1) when the enzyme was used free in solution. Analysis of water and soil samples with the developed nafion-based sensor produced inhibition on urease activity according to their metal contents. The obtained results were in agreement with the standard methods employed for sample analysis. Nevertheless, the use of the amperometric assay (with free urease) proved more feasible for the screening of trace amounts of metals in polluted samples.     

An Automated Multi-Pumping Pulsed Flow System with Spectrophotometric Detection for the Determination of Phosphate in Natural Waters

In this work, an automated multipumping pulsed flow system was implemented for the determination of phosphate in natural waters. The developed flow approach was based on the spectrophotometric determination of phosphate by using the vanadomolybdate reaction. The exploitation of a very simple manifold configuration relying on the utilization of just two active components, in this case two solenoid actuated micropumps that were accountable for sample and reagent insertion and commutation, reaction zone formation, and solutions propelling, provided a great operational and optimization simplicity, low reagent consumption, and waste minimization.

Linear calibration plots for phosphate concentrations of up to 20 mg L^?1 (R² = 0.999, n = 6) were obtained, with a detection limit of 0.2 mg L^?1. The sampling rate was about 60 samples per hour. The system was applied to the monitoring of phosphate in local streams at specific sampling stations.     

Direct determination of copper in urine using a sol–gel optical sensor coupled to a multicommutated flow system

In this work, a multicommutated flow system incorporating a sol–gel optical sensor is proposed for direct spectrophotometric determination of Cu(II) in urine. The optical sensor was developed by physical entrapment of 4-(2-pyridylazo)resorcinol (PAR) in sol–gel thin films by means of a base-catalysed process. The immobilised PAR formed a red 2:1 complex with Cu(II) with maximum absorbance at 500 nm. Optical transduction was based on a dual-colour light-emitting diode (LED) (green/red) light source and a photodiode detector. The sensor had optimum response and good selectivity towards Cu(II) at pH 7.0 and its regeneration was accomplished with picolinic acid. Linear response was obtained for Cu(II) concentrations between 5.0 and 80.0 g L^–1, with a detection limit of 3.0 g L^–1 and sampling frequency of 14 samples h^–1. Interference from foreign ions was studied at a 10:1 (w/w) ion:Cu(II) ratio. Results obtained from analysis of urine samples were in very good agreement with those obtained by inductively coupled plasma mass spectrometry (ICP–MS); there was no significant differences at a confidence level of 95%.     

Investigation of 2-[(<Emphasis Type="Italic">E</Emphasis>)-2-(4-diethylaminophenyl)-1-ethenyl]-1,3,3-trimethyl-3H-indolium as a new highly sensitive reagent for the spectrophotometric determination of nitrophenols

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of nitrophenols [picric acid (PA); dinitrophenols (DNP)] in wastewater samples. The method is based on the reaction of nitrophenols with 2-[(E)-2-(4-diethylaminophenyl)-1-ethenyl]-1,3,3-trimethyl-3 H-indolium chloride reagent to form the colored ion associates, which are extracted by organic solvents. The molar absorptivity of the ion associates of PA with the investigated reagent ranges from 8.3×10⁴ to 11.3×10⁴ L mol^–1 cm^–1, depending on the extractant. Because only PA is extracted in an acidic medium with the investigated reagent, but both PA and DNP are extracted in an alkaline medium, it is possible to determine both substances in a mixture. Appropriate reaction conditions have been established. The absorbance of the colored extracts obeys Beers law in the range of 0.04–4.58 mg L^–1 PA, 1.0–18.4 mg L^–1 2,4-DNP and 1.2–14.7 mg L^–1 2,6-DNP, respectively. The limit of detections, calculated from a blank test (n=10; P=0.95), are 0.05 mg L^–1 PA, 0.9 mg L^–1 (2,4-DNP), and 1.1 mg L^–1 (2,6-DNP), respectively.     

Development and critical comparison of greener flow procedures for nitrite determination in natural waters

Two greener procedures for flow-injection spectrophotometric determination of nitrite in natural waters were developed and critically compared. Replacement of toxic reagents, waste minimization and treatment were exploited to attend the standards of clean chemistry. The flow system was designed with solenoid micro-pumps in order to minimize reagent consumption and waste generation. The first procedure is based on the Griess diazo-coupling reaction with sulfanilamide and N-(1-naphthyl)ethylenediamine (NED) yielding an azo dye, followed by photodegradation of the low amount of waste generated based on the photo-Fenton reaction. The second procedure is based on the formation of iodine from nitrite and iodide in acid medium in order to avoid the use of toxic reagents. For Griess method, linear response was achieved up to 1.0 mg L^− 1, described by the equation A = − 0.007 + 0.460C (mg L^− 1), r = 0.999. The detection limit was estimated as 8 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.8% (n = 20). The sampling rate was estimated as 108 determinations per hour. The consumption of the most toxic reagent (NED) is reduced 55-fold and 20-fold in comparison to batch method and flow injection with continuous reagent addition, respectively. A colorless residue was obtained by in-line photodegradation with reduction of 87% of the total organic carbon content. The results obtained for natural water samples were in agreement with those achieved by the reference method at the 95% confidence level. For the nitrite–iodide method, linear response was observed up to 2.0 mg L^− 1, described by the equation A = − 0.024 + 0.148C (mg L^− 1), r = 0.999. The detection limit was estimated as 25 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.6% (n = 20). The sampling rate was estimated as 44 determinations per hour. Despite avoiding the use of toxic reagents, the nitrite–iodide method presented worst performance in terms of selectivity and sensitivity.     

A novel derivatisation procedure for inorganic mercury(II) for HPLC analysis

Summary A new procedure for derivatisation of inorganic mercury(II) to diphenylethynylmercury with simultaneous extraction into dichloromethane is proposed. The organomercury derivative is effectively analysed by HPLC using UV detection. The calibration curve is linear over three orders of magnitude (0.02–50 mg L^–1 Hg); the detection limit is 0.1 ng Hg. A preliminary study of the effect of potential interfering agents, in particular Cu(II), Zn(II), Cd(II), Pb(II), and cysteine, and applications of the present methodology to real environmental samples are presented.     

Trace Analysis of Heavy Metals with Two New Disodium Bisdithiocarbamates

Two chelating reagents, disodium N,N′-dibenzylethylenebisdithiocarbamate 1 and disodium piperazinebisdithiocarbamate 2, were synthesized and used to preconcentrate trace metals in aqueous samples. For analysis of Cu(II) using a UV-vis spectrometer, Beer's law was obeyed from 5.0 μg L^?1 to 6.0 mg L^?1 for reagent 1, and from 0.2 mg L^?1 to 6.0mg L^?1 for reagent. 2. The chelation ratio for reagent 1 to Cu(II) was determined to be 1:1, with a formation constant 1.0 × 10⁹ M^?l. The dependence of extraction and extraction efficiency of reagent 1 on pH was also studied with an atomic absorption spectrometer for nine heavy-metal ions-Cu(II), Fe(III), Pb(II), Co(II), Cr(VI), Ni(II), Zn(II), Mn(II) and Cd(II). Except Cr(VI) and Mn(II), the recovery yields of the other seven metal ions were almost quantitative at pH = 4 ? 6. The recovery was 82% for Cr(VI) at pH = 4 ? 5, and 52% for Mn(II) at pH = 6 ? 7.     

Exploiting monosegmented flow analysis to perform in-line standard additions using a single stock standard solution in spectrophotometric sequential injection procedures

The robustness of sequential injection analysis (SIA) was combined with the monosegmented flow analysis (MSFA) approach, in which there is no dispersion of the reaction zone with carrier, to develop a methodology to perform in-line dilution. This approach allows one to know accurately the dilution of sample and reagent inside the monosegment, without the need for determination of dispersion coefficients. As a consequence, the methodology allowed the mechanization of procedures to perform standard additions and to construct analytical curves using a single stock standard solution, with very simple and conventional computation of the sample concentration. The method was illustrated with experiments using the bromothymol blue (BTB) dye, in which no reactions are involved, as well as with the spectrophotometric methodology for determination of Fe(II) using o-1,10-phenanthroline as chromogenic reagent. The resulting method presented a sampling frequency of 30 analyses per hour and a detection limit of 25 μg l⁻¹.     

Simple and selective method for determination of iodide in pharmaceutical products by flow injection analysis using the iodine–starch reaction

This work exploited the well-known iodine–starch reaction for development of a simple flow-injection (FI) method for determination of iodide in pharmaceutical samples. Iodide in an injected zone was oxidized to iodine. A gas diffusion unit enables selective permeation of iodine through a hydrophobic membrane. Detection was made very selective for elemental iodine by employing formation of the I₃ ^––starch complex. The detection limit (3S/N) of the system was 1 mg I L^–1. For a liquid patent medicine used for asthma treatment we suggested modification of the system. Direct injection of this sample, which contains a particularly high concentration level of iodide (ca. 9000 mg I L^–1), can be achieved by coupling a dialysis unit to the FI system. This has increased the working range to 6000–10,000 mg I L^–1 without employing complicated nanoliter injection.     

Rapid spectrofluorimetric determination of lisinopril in pharmaceutical tablets using sequential injection analysis

The present work reports for the first time a simple and rapid method for the spectrofluorimetric determination of lisinopril (LSP) in pharmaceutical formulations using sequential injection analysis (SIA). The method is based on reaction of LSP with o-phthalaldehyde (OPA) in the presence of 2-mercaptoethanol (borate buffer medium, pH=10.6). The emission of the derivative is monitored at 455 nm upon excitation at 346 nm. The various chemical and physical conditions that affected the reaction were studied. The calibration curve was linear in the range 0.3–10.0 mg L^–1 LSP, at a sampling rate of 60 injections h^–1. Consumption of OPA reagent was significantly reduced compared with conventional flow injection (FI) systems, because only 50 L of OPA was consumed per run. The method was found to be adequately precise (s_r=2% at 5 mg L^–1 LSP, n=10) and the 3 detection limit was 0.1 mg L^–1. The method was successfully applied to the analysis of two pharmaceutical formulations containing LSP. The results obtained were in good agreement with those obtained by use of high-performance liquid chromatography (HPLC), because the mean relative error, e_r, was <1.8%.     

Spectrophotometric determination of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3- H-indol-2-ylidene)propenyl]-3 H-indolium

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of manganese in sewage. The method is based on the reaction of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3-H-indol-2-ylidene)propenyl]-3H-indolium to form a colored ion associate with a sensitive absorption maximum at 560 nm. The appropriate reaction conditions have been established: pH 8.5–10.0, 1.25–2.3×10^–3 mol L^–1 1-nitroso-2-naphthol, and 1.6–2.4×10^–4 mol L^–1 dye reagent. Beer's law is obeyed for manganese concentrations up to 4.2 mg L^–1. The limit of detection is 0.01 mg L^–1 Mn²⁺; the molar absorptivity of the ion associate was 7.5×10⁴ L mol^–1 cm^–1. The effect of various foreign ions was examined. A reaction mechanism is suggested. The developed procedure was tested for determination of manganese in sewage with satisfactory precision and accuracy.     

A green flow-based procedure for fluorimetric determination of acid-dissociable cyanide in natural waters exploiting multicommutation

A flow system designed with solenoid valves is proposed for determination of weak acid dissociable cyanide, based on the reaction with o-phthalaldehyde (OPA) and glycine yielding a highly fluorescent isoindole derivative. The proposed procedure minimizes the main drawbacks related to the reference batch procedure, based on reaction with barbituric acid and pyridine followed by spectrophotometric detection, i.e., use of toxic reagents, high reagent consumption and waste generation, low sampling rate, and poor sensitivity. Retention of the sample zone was exploited to increase the conversion rate of the analyte with minimized sample dispersion. Linear response (r = 0.999) was observed for cyanide concentrations in the range 1–200 μg L⁻¹, with a detection limit (99.7% confidence level) of 0.5 μg L⁻¹ (19 nmol L⁻¹). The sampling rate and coefficient of variation (n = 10) were estimated as 22 measurements per hour and 1.4%, respectively. The results of determination of weak acid dissociable cyanide in natural water samples were in agreement with those achieved by the batch reference procedure at the 95% confidence level. Additionally to the improvement in the analytical features in comparison with those of the flow system with continuous reagent addition (sensitivity and sampling rate 90 and 83% higher, respectively), the consumption of OPA was 230-fold lower.     

Enhancing effect of DNA on chemiluminescence from the decomposition of hydrogen peroxide catalyzed by copper(II)

In the absence of any special luminescence reagent, emission of weak chemiluminescence has been observed during the decomposition of hydrogen peroxide catalyzed by copper(II) in basic aqueous solution. The intensity of the chemiluminescence was greatly enhanced by addition of DNA and was strongly dependent on DNA concentration. Based on these phenomena, a flow-injection chemiluminescence method was established for determination of DNA. The chemiluminescence intensity was linear with DNA concentration in the range 2×10^–7–1×10^–5 g L^–1 and the detection limit was 4.1×10^–8 g L^–1 (S/N=3). The relative standard deviation was less than 3.0% for 4×10^–7 g L^–1 DNA (n=11). The proposed method was satisfactorily applied for determination of DNA in synthetic samples. The possible mechanism of the CL reaction is discussed.     

Spectrophotometric determination of Cu(II) with sequential injection analysis

A sequential injection system, based on the reaction of Cu(II) with diethyldithiocarbamate (DDTC), was developed for the determination of Cu(II) in plant food and water samples. The extraction procedure, generally used to extract the Cu(II)–DDTC complex for subsequent analysis was eliminated in this procedure. The complex was detected spectrophotometrically in aqueous solutions at 460 nm. The physical and chemical parameters depicting the system were studied to obtain optimum conditions for sample analysis. The system developed is fully computerized and able to monitor Cu(II) in samples at seven samples per hour with a relative standard deviation of <4.50%. The calibration curve is linear from 0.5–5.0 mg/l with a detection limit of 0.2 mg/l. Interferences were reduced by introducing multiple flow reversals, to increase mixing between the reagent and sample zones, and subsequently enhance working of the masking agents (EDTA/citrate).     

Determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder by flow injection analysis with spectrophotometric detection

In this work, a flow injection system with spectrophotometric detection was developed for the determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder. Reaction between Quinizarine (1,4-dihydroxyanthraquinone) and Li(I) ion in alkaline medium containing dimethylsulfoxide (DMSO) was explored for this purpose. The flow system was optimized regarding to its chemical (DMSO, Quinizarine and NaOH concentrations and sample pH) and physical parameters (sample loop volume, carrier flow rate and reactor length) in order to establish better conditions in terms of sensitivity and sampling frequency. The results obtained showed that the concentration of DMSO in the reagent solution presents remarkable influence on the magnitude of analytical signal. Chemical species that could be found in the formulations such as Na(I), K(I), Mg(II), Ca(II), Ti(IV), Cl⁻, CO₃²⁻ e sodium dodecylsulfate were tested as possible interfering ions. Among them, only non-monovalent cations presented noticeable interference on lithium signal. However, they were not found in concentrations high enough to cause interference in the determination of lithium in the samples. Sample preparation was performed by sonicating a slurry prepared by dispersing 100 mg of powdered sample in 15 mL of 0.10 mol L⁻¹ HCl solution. Results obtained by developed methodology were not statistically different from those obtained by flame emission spectrometry. In the optimized conditions the method presented a linear range of 5-40 mg L⁻¹ and a relative standard deviation of 3.6% at 5 mg L⁻¹ Li concentration. Detection and quantification limits were 0.54 and 1.8 mg L⁻¹, respectively. Sampling frequency, calculated as the time interval passed between two consecutive injections, was 60 samples per hour. The methodology was successfully applied in the determination of lithium in three commercial samples.     

Flow Analysis of Transition Metals by Thermal Lensing

The conditions for the flow determination of Al(III), Bi(III), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Mn(II), Nd(III), Ni(II), Pb(II), Pr(III), and Zn(II) by reaction with Xylenol Orange in aqueous solutions at pH 4.5 and the determination of Cd(II), Co(II), Cu(II), Fe(II), Ni(II), Pb(II), and Zn(II) by reaction with 4-(2-thiazolylazo)resorcinol in water–ethanol mixtures (5 : 1) at pH 5.0 using an injected sample volume of 80 L were proposed. The limits of detection were n × 10^–8–n × 10^–7 mol/L; the linearity ranges in the calibration graphs were of about three orders of magnitude; the relative standard deviation was of 3–7%.