Evaluation of a carbon paste electrode modified with organofunctionalised SBA-15 nanostructured silica in the simultaneous determination of divalent lead, copper and mercury ions

The performance of a carbon paste electrode (CPE) modified with SBA-15 nanostructured silica organofunctionalised with 2-benzothiazolethiol in the simultaneous determination of Pb(II), Cu(II) and Hg(II) ions in natural water and sugar cane spirit (cacha?a) is described. Pb(II), Cu(II) and Hg(II) were pre-concentrated on the surface of the modified electrode by complexing with 2-benzothiazolethiol and reduced at a negative potential (-0.80 V). Then the reduced products were oxidised by DPASV procedure. The fact that three stripping peaks appeared on the voltammograms at the potentials of -0.48 V (Pb2+), -0.03 V (Cu2+) and +0.36 V (Hg2+) in relation to the SCE, demonstrates the possibility of simultaneous determination of Pb2+, Cu2+ and Hg2+. The best results were obtained under the following optimised conditions: 100 mV pulse amplitude, 3 min accumulation time, 25 mV s(-1) scan rate in phosphate solution pH 3.0. Using such parameters, calibration graphs were linear in the concentration ranges of 3.00-70.0 x 10(-7) mol L(-1) (Pb2+), 8.00-100.0 x 10(-7) mol L(-1) (Cu2+) and 2.00-10.0 x 10(-6) mol L(-1) (Hg2+). Detection limits of 4.0 x 10(-8) mol L(-1) (Pb2+), 2.0 x 10(-7) mol L(-1) (Cu2+) and 4.0 x 10(-7) mol L(-1) (Hg2+) were obtained at the signal noise ratio (SNR) of 3. The results indicate that this electrode is sensitive and effective for simultaneous determination of Pb2+, Cu2+ and Hg2+ in the analysed samples.     

Determination of components of the Cd(II)-Pb(II)-Cu(II) system in aqueous solutions of (polyethylene imine)methylthiourea by stripping voltammetry

Conditions were studied for the stripping voltammetric determination of components of the Cd(II)-Pb(II)-Cu(II) system in aqueous solutions of (polyethylene imine)methylthiourea (PMT), the most efficient polymer complexant for the membrane preconcentration of heavy metal ions. It was shown that PMT significantly enhances the selectivity of determining Pb(II) and Cd(II) in solutions of Cu(II) by stripping voltammetry. Pb(II) and Cd(II) can be determined in the presence of up to 200- and 50-fold amounts of Cu(II), respectively. The limits of detection for Pb(II) and Cd(II) after a 40-s accumulation were 6.9 x 10^-8 and 6.8 x 10^-7 M, respectively.     

Voltammetric copper(II) determination with a montmorillonite-modified carbon paste electrode

The clay mineral montmorillonite has been tested as modifier for the carbon paste electrode with a novel electrode modification technique. The differential pulse voltammetric determination of copper(II) by means of this modified carbon paste electrode has been studied. A detection limit of 4x10(-8) mol/l has been achieved after 10 min preconcentration under open circuit conditions with subsequent anodic stripping voltammetry. The calibration curve for Cu(II) is linear in the range of 4x10(-8)-8x10(-7) mol/l. Pb interferes in a 10-fold molar and Cd and Hg in a 100-fold molar excess. The interference by humic ligands is significant.     

Stripping Voltammetric Determination of Pb(II) and Cd(II) Based on the Multiwalled Carbon Nanotubes-Nafion-Bismuth Modified Glassy Carbon Electrodes

Abstract

In this work, a new method for the simultaneous determination of Pb(II) and Cd(II) on the multiwalled carbon nanotubes (MWNT)-Nafion-bismuth modified glassy carbon electrode (GCE) using square-wave anodic stripping voltammetry has been studied. Scanning electron microscopy was used to investigate the characteristics of the MWNT-Nafion-bismuth modified GCE. Well-defined sharp stripping peaks were observed in the determination of Pb(II) and Cd(II) simultaneously on this electrode. Under optimized conditions, the lowest detectable concentrations were 50 ng/l for Pb(II) and 80 ng/l for Cd(II) under a 10 min preconcentration. The attractive performances of MWNT-Nafion-bismuth modified GCE demonstrated its application for a simple, rapid, and harmless determination of trace heavy metals.     

Copper(II)-selective electrode using 2,2'-dithiodianiline as neutral carrier

Poly(vinyl chloride) membrane electrode, that is highly selective and sensitive to Cu(II) ions, was developed by using 2,2'-dithiodianiline and dibutyl phthalate as carrier and plasticizer, respectively. The electrode exhibits good potentiometric response for Cu(II) over a wide concentration range (5.0x10(-2)-7.0x10(-7) mol l(-1)) with Nernstian slope of 30+/-1 mV per decade. The response time of the electrode is 10 s and it has been used for a period of one month and exhibits good selectivity towards Cu(2+) in comparison to alkali, alkaline earth, transition and heavy metal ions, with no interference caused by Pb(2+), Cd(2+) and Fe(+2) which are known to interfere with many other copper electrodes.     

Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

Cathodic adsorptive stripping square-wave voltammetric determination of nifedipine drug in bulk,pharmaceutical formulation and human serum

Nifedipine is a calcium-channel antagonist drug used in the management of angina pectoris and hypertension through inhibition of calcium influx. A fully validated sensitive cathodic adsorptive stripping square-wave voltammetry procedure was optimized for the determination of the drug at trace levels. The procedure was based on the reduction of the nitrophenyl group after the interfacial accumulation of the drug onto a hanging mercury drop electrode in Britton-Robinson buffer of pH 11.0. The optimal conditions of the procedure were found to be: accumulation potential=-0.9 V vs. Ag/AgCl/KCl(s)), accumulation time=30 s, scan increment=10 mV, pulse amplitude=50 mV and frequency=120 Hz. Under these conditions, a well-defined peak was obtained; its peak current showed a linear dependence on drug concentration in the range of 2x10(-9)-2x10(-7) mol L(-1) bulk nifedipine. The mean recoveries based on eight replicate measurements for 1x10(-8) and 5x10(-8) mol L(-1) bulk nifedipine solutions were 98.46+/-0.86% and 98.23+/-0.92%, respectively. A detection limit of 3.42x10(-10) mol L(-1) bulk nifedipine was achieved. The procedure was successfully applied for assay of the drug in tablets and spiked human serum with mean recoveries of 101.95+/-1.42% and 98.70+/-0.63%, respectively. The limit of detection of the drug in spiked human serum was found to be 3.90x10(-10) mol L(-1).     

Simultaneous Determination of Copper(II), Lead(II) and Zinc(II) at Bismuth Film Electrode by Multivariate Calibration

In this work, simultaneous determination of Cu(II), Pb(II) and Zn(II) ions at low concentration levels (ppb) by square wave anodic stripping voltammetry on a Bi(III) film electrode plated in situ at a glassy carbon electrode (GCE) is described. A chemometric approach was used to overcome the overlapping peaks of Cu(II) and Bi(III), the competition of the electrodeposited Cu and Bi for the surface of the GCE and the formation of Cu‐Zn intermetallic compounds. The construction of the multivariate calibration models, based on partial least squares regression, allowed the simultaneous determination of Cu (in the concentration range 8.0 to 20.1 ppb), Pb (2.0 to 30.0 ppb) and Zn (29.7 to 90.4 ppb) with most of the prediction errors obtained in the external validation set for the three models lower than 16, 11 and 26 %, respectively. Finally, this method was used for the determination of these trace metal ions in surface river water samples with satisfactory results [errors below 10, 5 and 32 % for Cu(II), Pb(II) and Zn(II), respectively].     

Differential pulse anodic stripping voltammetry of lead (lI) benzoylacetonate in chloroform: Application to the analysis of free-lead gasoline and gas oil samples

The voltammetric characteristics of lead(II) benzoylacetonate in chloroform at the mercury electrode are investigated. The conditions for nearly reversible reduction of lead(II) were optimized. Anodic stripping voltammetry for the determination of trace-lead was developed using differential pulse technique to strip amalgamed lead from hanging mercury drop electrode. The experimental conditions, such as scanning rate of electrode potential and deposition time of lead were optimized. The calibration graph was linear over concentration range 5x10(-8)-10(-6) M of lead(II). The detection limit was 2.5x10(-9) and the relative standard deviation for the determination of 4x10(-7) M Pb(II) was 2%. Preceded by decomposition of organolead compounds with concentrated nitric acid, then ashing at 300 degrees C and a solvent extraction of Pb(II) benzoylacetonate in chloroform, the suitability of the proposed method for the determination of lead in free-lead gasoline and gas oil was demonstrated as a typical example of application.     

Thermal lens studies of the reaction of iron (II) with 1,10-phenanthroline at the nanogram level

The determination of iron(II) with 1,10-phenanthroline in aqueous solutions was carried out exemplarily by thermal lens spectrometry. The peculiarities of analytical reactions at the nanogram level of reactants can be studied using this method. Under the conditions of the competing reaction of ligand protonation, the overall stability constant for iron(II) chelate with 1,10-phenanthroline was determined at a level of n x 10(-7) mol L(-1), logbeta3 = 21.3+/-0.1. The rates of formation and dissociation of iron(II) tris-(1,10-phenanthrolinate) at a level of n x 10(-8) mol L(-1) were found to be (2.05+/-0.05) x 10(-2) min(-1) and (3.0+/-0.1) x 10(-3) min(-1), respectively. The conditions for the determination of iron(II) with 1,10-phenanthroline by thermal lensing were reconsidered, and ascorbic acid was shown to be the best reducing agent, which provided minimum and reproducible sample pretreatment. Changes in the conditions at the nanogram level improved both the selectivity and sensitivity of determination. The optimum measurement conditions for thermal lensing were determined not only by the absorption of the analyte and reagents, but also by the background absorption of the solvent. The limits of detection and quantification of iron(II) at 488.0 nm (excitation beam power 140 mW) are 1 x 10(-9) and 6 x 10(-9) mol L(-1), respectively; the reproducibility RSD for the range n x 10(-8)-n x 10(-6) mol L(-1) is 2-5%.     

Cathodic stripping voltammetry of the anticancer agent 5-fluorouracil and determination in urine

Cathodic stripping voltammetry was used to determine 5-fluorouracil (5-FU) in the presence of traces of Cu(II). It was found that the addition of 5 x 10(-9) mol dm(-3) Cu(II) to the measurement cell greatly enhanced the peak current of the adsorbed molecule. Different parameters were tested to optimize the conditions for the determination of 5-FU. The adsorbed form is reduced irreversibly. It was observed that by controlling the deposition potential, the technique could be directed to the determination of Cu(II) or the drug. The linear range was from 5 x 10(-9) to 6 x 10(-8) mol dm(-3) for 5-FU and from 6 x 10(-9) to 5 x 10(-8) mol dm(-3) for Cu(II). Detection limits of 4.6 x 10(-10) and 5 x 10(-10) mol dm(-3) were obtained for 5-FU and Cu(II), respectively. The method was applied to urine and molecules or ions which may interfere were studied.     

Rapid and selective method for the spectrophotometric determination of nickel naphthenate in gasoline in a microemulsion

A new method for the spectrophotometric determination of nickel naphthenate in gasoline in a microemulsion was developed. PAN reacts with nickel(II) forming a red complex with composition 1:2 (metal to ligand) nickel(II)-PAN and absorption maximum at 568 nm. Nickel naphthenate in gasoline can be determined with PAN in a microemulsion, in the pH range 3.0 approximately 10.0 with a molar absorptivity of 4.8x10(4) l mol(-1) cm(-1). Beer's law was obeyed up to 0.8 mg l(-1) of nickel(II) in the microemulsion system. The interference of Cu(2+), Fe(3+), Mn(2+), Pb(2+) and Zn(2+) can be eliminated by adding 0.5 ml of a mixed masking agent. The method is rapid, simple and highly selective.     

A new lead(II)-selective PVC-coated graphite rod electrode based on a Schiff base complex.

A new lead(II)-selective electrode has been developed based on bis(acetylacetone)-p-phenylenediamine-lead(II) [LPb(NO3)2]H2O complex ionophore as a sensing material, dioctylphthalate (DOP) as a solvent mediator and PVC as a matrix. This electrode exhibits a linear Nernstian response over the concentration range of 1 x 10(-5)-1 x 10(-1) mol l(-1) of Pb(II) cation, with a cationic calibration slope of 30.0 +/- 0.2 mV/concentration decade and a detection limit of 2 x 10(-6) mol l(-1) (0.40 ppm). It has a fast response time and can be used for a period of 2 months without any divergence in potentials. The proposed electrode reveals a good selectivity for Pb(II) over a wide variety of other tested cations and could be used in the pH range of 4-8. It was successfully used for direct determination of Pb(II) concentration in some samples. The obtained results show a good agreement with those obtained by an atomic absorption spectrometric method. The average recovery obtained is 96.5 +/- 0.5% with standard deviation of 1.2% (n = 8).     

Coated-wire silver ion-selective electrode based on silver complex of cyclam.

A coated-wire ion-selective electrode (ISE) based on cyclam (1,4,8,11-tetraazacyclotetradecane) as a neutral carrier in a polyvinyl chloride (PVC) matrix was fabricated for the determination of Ag(I) ions. The coated-wire ISE exhibited a linear Nernstian response over the range 1 x 10(-1) to 1 x 10(-7) M with a slope of 59 +/- 2 mV per decade change and a detection limit of 5 x 10(-8) M. The ISE shows a greater preference for Ag over other cations with good precision. The electrode was selective towards Ag(I) ions in the presence of 13 different metal ions tested. The selectivity coefficients (K(ij)) were determined for Na(I), K(I), Mg(II), Ca(II), Ba(II), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Pb(II) and Hg(II). The selectivity coefficients of these cations are in the range of 10(-4) to 10(-2). This ISE was used for the determination of free silver and total silver in electroplating bath solutions, additives and brighteners.     

Determination of platinum(IV) by UV spectrophotometry

A simple, rapid and sensitive spectrophotometric procedure for the determination of platinum has been elaborated. Pt traces were determined in the form of the PtCl(6)(2-) complex in hydrochloric acid solution whose concentration varies from 0.01 to 2 mol L(-1) by measuring the absorbance at 260 nm. The detection limit is 4.7 x 10(-7) mol L(-1), the linearity range from 2 x 10(-6) mol L(-1) to 7 x 10(-6) mol L(-1), and the correlation coefficient is r=0.9990. No significant interferences were observed from a majority of the investigated ions, such as Zn(II), Pb(II), Mn(II), Cd(II), Co(II) and Ni(II) with the exception of Cu(II), Sb(III), Fe(III), Pd(II), Sn(II) and I(-) ions. The method was successfully applied for the determination of Pt traces in different solid samples and the recovery from inorganic materials was studied.     

Complexing Polymer Films in The Preparation of Modified Electrodes for Detection of Metal Ions

Summary: The complexing properties of poly (3-(pyrrol-1-yl)propylmalonic acid) (poly1) and poly(N,N′-ethylenebis[N-[(3-(pyrrole-1-yl)propyl) carbamoyl) methyl]-glycine (poly2) coated electrodes (C|poly1 and C|poly2) towards Cu(II), Pb(II), Hg(II) and Cd(II) cations using the open circuit chemical preconcentration-anodic stripping technique were studied. Sorption process of metal cations onto complexing surfaces was readily investigated through the combination of a chemical pre-concentration-anodic stripping technique with a Langmuir isotherm model. The modified electrodes were used for the voltammetric determination of Cu(II), Pb(II), Hg(II) and Cd(II) ions, giving low detection limits for Cu(II) (5 × 10⁻⁹ mol L⁻¹) and Pb(II) (5 × 10⁻¹⁰ mol L⁻¹). The ability of the modified electrodes to analyze Cu(II) ions in natural sample has been demonstrated by the analysis of a tap water sample. The results of the preconcentration process under competitive conditions clearly shows that the selectivity of complexing molecular electrode materials can be subtly tuned upon playing on the accumulation time, polymer thickness and/or memory effect of the binding polymers, opening up new avenues towards evolutive and efficient smart sensing materials.     

Simultaneous Voltammetric Determination of Zn(II), Pb(II), Cu(II), and Hg(II) in Ethanol Fuel Using an Organofunctionalized Modified Graphite‐Polyurethane Composite Disposable Screen‐Printed Device

A disposable screen‐printed device containing working, auxiliary, and reference electrodes is proposed for the simultaneous voltammetric determination of Zn(II), Pb(II), Cu(II), and Hg(II) in ethanol fuel. The working electrode was printed using an ink modified with 2‐benzothiazole‐2‐thiol organofunctionalized SBA‐15 silica, in order to increase sensitivity. The performance of this electrode was compared with that of bare and SBA‐15‐modified electrodes. After optimizing the experimental parameters, the device was applied in determination of the analytes in commercial ethanol fuel samples, using 0.10 mol L^?1 KCl/ethanol ratios of 30 : 70 (v/v), with [H⁺]=10^?5 mol L^?1. After 5 min of preconcentration at ? 1.3 V (vs. pseudo‐Ag/AgCl), four well‐resolved signals were obtained, enabling simultaneous determination of the four analytes using a differential pulse anodic stripping voltammetry (DPASV) procedure. The limits of detection were 0.30, 0.065, 0.030, and 0.046 µmol L^?1 for Zn(II), Pb(II), Cu(II), and Hg(II), respectively. The results of these analyses were in agreement with those obtained using graphite furnace atomic absorption spectroscopy (GFAAS) for Pb(II), Cu(II), and Hg(II), and high‐resolution continuum source flame atomic absorption spectrometry (HR‐CS‐FAAS) for Zn²⁺, at a 95 % confidence level. Analytes originally present in the samples could be detected, and the interference of some cations and anions was evaluated.     

Anodic stripping voltammetry at in situ bismuth-plated carbon and gold microdisc electrodes in variable electrolyte content unstirred solutions

Carbon and gold microdisc electrodes (30 and 10 μm, respectively) have been tested as substrates for in situ bismuth film plating from unstirred solutions of variable acetate buffer content and were subsequently used in the anodic stripping voltammetry determination of Pb(II) and Cd(II) ions. The effects of Bi(III) concentration, analyte accumulation time, stirring as well as supporting electrolyte content have been studied. Under optimal conditions good voltammetric responses were obtained by means of square wave anodic stripping voltammetry in unstirred analyte solutions of 5 × 10⁻⁸ to 10⁻⁶ M, even in the absence of added buffer. In an indicative application, Pb(II) ion levels were determined in tap water using bismuth-plated carbon microdisc electrodes.     

Dealing with interference challenge in the electrochemical detection of As(III) —A complexometric masking approach

Copper ion has been reported to be a major interference in the electrochemical detection of arsenic (III) ion in water. Therefore the development of a simple approach to alleviate this interference challenge is important. We present the use of ammonia solution as a masking agent for Cu(II) interference in the square wave anodic stripping voltammetry of As(III) on a gold nanoparticle modified glassy carbon electrode (GCE). AuNPs were electrochemically deposited by cyclic voltammetry on a GCE from a potential range of − 400 mV to 1100 mV for 10 cycles. Square wave anodic stripping voltammetry (SWASV) was used to detect As(III) in water with and without Cu(II) based on the following optimised conditions: pH = 3, deposition potential = − 600 mV, and deposition time = 60 s. Ammonia solution was added to the analyte solution and the effect on mitigating copper interference was studied. The presence of ammonia complexed the Cu(II) ion thereby excluding Cu(II) from interfering with the As(III) signal.     

Bis(2-hydroxyacetophenone)ethylenediimine as a neutral carrier in a coated-wire membrane electrode for lead(II).

A coated-wire ion-selective electrode (CWISE), based on a Schiff base as a neutral carrier, was successfully developed for the detection of Pb(II) in aqueous solution. CWISE exhibited a linear response with a Nernstian slope of 29.4 +/- 0.5 mV/decade within the concentration range of 1.0 x 10(-5) - 1.0 x 10(-1) M lead ion. CWISE has shown detection limits of 5.0 x 10(-6) M. The electrode exhibited good selectivity over a number of alkali, alkaline earth, transition and heavy metal ions. This sensor yielded a steady potential within 10 to 20 s at a linear dynamic range. The electrode was suitable for use in aqueous solutions in a pH range of 2.0 to 5.0. Applications of this electrode for the determination of lead in real samples and as indicator electrode for potentiometric titration of Pb2+ ion using K2CrO4 are reported.