双波长双指示剂催化光度法测定痕量Mn(Ⅱ)

在硫酸介质中,以氨三乙酸为活化剂,利用痕量Mn(Ⅱ)催化高碘酸钾氧化灿烂绿和酸性铬蓝K褪色的指示反应,分别在430nm和630nm波长下测量催化体系和非催化体系的吸光度,建立了双指示剂双波长催化动力学光度法测定痕量Mn(Ⅱ)的新方法。在优化条件下,测定Mn(Ⅱ)的线性范围为0.00200～0.0300μg/mL,检出限为1.2×10-11 g/mL。方法可用于茶叶和废水中痕量锰的测定。     

催化动力学分光光度法测定痕量锰(Ⅱ)

研究了氢氧化钠介质中 ,痕量锰催化过氧化氢氧化桑色素褪色反应及其动力学条件 ,建立了催化动力学测定痕量锰的新方法。Mn (Ⅱ )的测定线性范围为 0 0 0 5～ 0 0 60 μg/2 5mL ,检出限为 7 8× 1 0 - 10 g·mL- 1。用于大米中痕量Mn (Ⅱ )的测定 ,结果满意。     

以N-十二烷基二甲基铵基乙酸为增敏剂催化光度法测定痕量锰

报道了以氨三乙酸为活化剂,以N-十二烷基二甲基铵基乙酸(DDMAA)为增敏剂,高碘酸钾氧化天青(Ⅱ)催化光度法测定痕量锰的新方法.本法在两性表面活性剂DDMAA存在下,灵敏度提高了3.3倍(锰量为 0.4～2.0 μg/L)和 5.6倍(锰量为2.0～6.0μg/L);相对标准偏差为1.3%(n=11),方法的检出限为5.2×10~(-11)g/mL.可用于茶叶中锰的测定.     

催化光度法测定粮食中的痕量锰

研究了测定痕量锰的新催化光度法,方法基于氨三乙酸为活化剂,锰（Ⅱ）催化高碘酸钾氧化溴酚蓝的反应。测定锰的线性范围为0．4－10ng/mL,检出限为0．082ng/mL,对于4.0ng/mL Mn(Ⅱ）的测定,相对标准偏差为3．4％（n=9),其方法已用于粮食中锰的测定。     

催化动力学光度法测定锰

研究了在活化剂氮三乙酸(NTA)存在下,Mn2 催化KIO4氧化刚果红(Gongo Red)褪色反应的条件。建立了催化动力学光度法测定痕量锰的新方法。在测定波长496 nm时,锰测定的线性范围为0~2.8×10-9g/mL,检出限为2.76×10-11g/mL,探讨了有关的反应机理,考察了20余种共存离子对测定的影响,用于大米、绿豆、小米和水样中痕量锰的测定。     

茜素红-H2O2-溴代十六烷基吡啶-丙氨酸体系催化光度法测定痕量锰

研究了在溴代十六烷基吡啶(CPB)增敏剂和丙氨酸活化剂存在下,锰(Ⅱ)对过氧化氢氧化茜素红的褪色反应及其动力学条件,建立了测定痕量锰(Ⅱ)的新方法。讨论了pH值和共存离子对痕量锰(Ⅱ)测定的影响。在最佳实验条件下,本法测定痕量锰(Ⅱ)的线性范围为10~360μg/L,检出限为2.01×10-8g/L。方法用于水样中痕量锰(Ⅱ)的测定,结果满意。     

偶氮胂I-高碘酸钾催化光度法测定痕量Mn(Ⅱ)

研究了在HAc—NH4Ac介质中，以1，10-菲啰啉为活化剂，锰(Ⅱ)催化高碘酸钾氧化偶氮胂I褪色反应的条件及影响因素，建立了动力学光度法测定痕量Mn(Ⅱ)的新方法。方法线性范围为0-80μg/L，检出限为6．3ng/mL，对60μg/L,Mn(Ⅱ)测定的相对标准偏差为2．6％。导出了动力学方程，该催化反应的表观活化能为130．4kJ／mol。已用于野菜、水果样品中锰(Ⅱ)的测定。     

催化光度法测定人发中超痕量钴的研究

本文研究了氨水介质中钴(Ⅱ)催化过氧化氢氧化邻苯二酚紫褪色反应及其动力学条件,建立了测定超痕量钴(Ⅱ)的快速方法。测定钴(Ⅱ)的范围为0～40×1/25 ng/mL,方法灵敏度为1.2×10~(-12)g/mL,用以测定人发中的痕量钴(Ⅱ),获得了满意结果。     

催化光度法测定痕量猛——高碘酸钾-Mn(Ⅱ)-邻菲啰啉-溴酚蓝体系

本文以高碘酸钾-溴酚蓝为指示反应,在活化剂邻菲(口罗)啉存在下建立了催化光度法测定痕量锰(Ⅱ)的新方法,方法灵敏度为6×10~4μg/ml。线性范围为0.00—0.60μg/15ml,应用于标准铝合金及茶叶中痕量锰的测定,结果令人满意。     

锰(Ⅱ)催化氧化1，5-二(2-羟基-5-磺酸基苯)-3-氰基甲动力学及其应用

建立了一种测定痕量锰的新方法,并对反应的最佳条件、动力学参数及反应机理进行探讨,建立了反应动力学方程。方法测定 Mn(Ⅱ)范围 0.00～1.00 ng/mL,检出限 8.5×10-12 g/mL。方法可用于一次蒸馏水和井水中痕量锰的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.