Transmission‐mode diamond white‐beam position monitor at NSLS

Two transmission‐mode diamond X‐ray beam position monitors installed at National Synchrotron Light Source (NSLS) beamline X25 are described. Each diamond beam position monitor is constructed around two horizontally tiled electronic‐grade (p.p.b. nitrogen impurity) single‐crystal (001) CVD synthetic diamonds. The position, angle and flux of the white X‐ray beam can be monitored in real time with a position resolution of 500 nm in the horizontal direction and 100 nm in the vertical direction for a 3 mm × 1 mm beam. The first diamond beam position monitor has been in operation in the white beam for more than one year without any observable degradation in performance. The installation of a second, more compact, diamond beam position monitor followed about six months later, adding the ability to measure the angular trajectory of the photon beam.     

Large‐acceptance diamond planar refractive lenses manufactured by laser cutting

For the first time, single‐crystal diamond planar refractive lenses have been fabricated by laser micromachining in 300 µm‐thick diamond plates which were grown by chemical vapour deposition. Linear lenses with apertures up to 1 mm and parabola apex radii up to 500 µm were manufactured and tested at the ESRF ID06 beamline. The large acceptance of these lenses allows them to be used as beam‐conditioning elements. Owing to the unsurpassed thermal properties of single‐crystal diamond, these lenses should be suitable to withstand the extreme flux densities expected at the planned fourth‐generation X‐ray sources.     

X‐ray position‐sensitive duo‐lateral diamond detectors at SOLEIL

The performance of a diamond X‐ray beam position monitor is reported. This detector consists of an ionization solid‐state chamber based on a thin single‐crystal chemical‐vapour‐deposition diamond with position‐sensitive resistive electrodes in a duo‐lateral configuration. The detector's linearity, homogeneity and responsivity were studied on beamlines at Synchrotron SOLEIL with various beam sizes, intensities and energies. These measurements demonstrate the large and homogeneous (absorption variation of less than 0.7% over 500 µm × 500 µm) active area of the detector, with linear responses independent of the X‐ray beam spatial distribution. Due to the excellent charge collection efficiency (approaching 100%) and intensity sensitivity (0.05%), the detector allows monitoring of the incident beam flux precisely. In addition, the in‐beam position resolution was compared with a theoretical analysis providing an estimation of the detector's beam position resolution capability depending on the experimental conditions (X‐ray flux, energy and readout acquisition time).     

Pixelated transmission‐mode diamond X‐ray detector

Fabrication and testing of a prototype transmission‐mode pixelated diamond X‐ray detector (pitch size 60–100 µm), designed to simultaneously measure the flux, position and morphology of an X‐ray beam in real time, are described. The pixel density is achieved by lithographically patterning vertical stripes on the front and horizontal stripes on the back of an electronic‐grade chemical vapor deposition single‐crystal diamond. The bias is rotated through the back horizontal stripes and the current is read out on the front vertical stripes at a rate of ～1 kHz, which leads to an image sampling rate of ～30 Hz. This novel signal readout scheme was tested at beamline X28C at the National Synchrotron Light Source (white beam, 5–15 keV) and at beamline G3 at the Cornell High Energy Synchrotron Source (monochromatic beam, 11.3 keV) with incident beam flux ranges from 1.8 × 10^?2 to 90 W mm^?2. Test results show that the novel detector provides precise beam position (positional noise within 1%) and morphology information (error within 2%), with an additional software‐controlled single channel mode providing accurate flux measurement (fluctuation within 1%).     

Diamond X‐ray beam‐position monitoring using signal readout at the synchrotron radiofrequency

Single‐crystal diamond is a material with great potential for the fabrication of X‐ray photon beam‐position monitors with submicrometre spatial resolution. Low X‐ray absorption combined with radiation hardness and excellent thermal‐mechanical properties make possible beam‐transmissive diamond devices for monitoring synchrotron and free‐electron laser X‐ray beams. Tests were made using a white bending‐magnet synchrotron X‐ray beam at DESY to investigate the performance of a position‐sensitive diamond device using radiofrequency readout electronics. The device uniformity and position response were measured in a 25 µm collimated X‐ray beam with an I‐Tech Libera `Brilliance' system. This readout system was designed for position measurement and feedback control of the electron beam in the synchrotron storage ring, but, as shown here, it can also be used for accurate position readout of a quadrant‐electrode single‐crystal diamond sensor. The centre‐of‐gravity position of the F4 X‐ray beam at the DORIS III synchrotron was measured with the diamond signal output digitally sampled at a rate of 130 Msample s^?1 by the Brilliance system. Narrow‐band filtering and digital averaging of the position signals resulted in a measured position noise below 50 nm (r.m.s.) for a 10 Hz bandwidth.     

Suppression of Bragg reflection glitches of a single‐crystal diamond anvil cell by a polycapillary half‐lens in high‐pressure XAFS spectroscopy

In combination with a single‐crystal diamond anvil cell (DAC), a polycapillary half‐lens (PHL) re‐focusing optics has been used to perform high‐pressure extended X‐ray absorption fine‐structure measurements. It is found that a large divergent X‐ray beam induced by the PHL leads the Bragg glitches from single‐crystal diamond to be broadened significantly and the intensity of the glitches to be reduced strongly so that most of the DAC glitches are efficiently suppressed. The remaining glitches can be easily removed by rotating the DAC by a few degrees with respect to the X‐ray beam. Accurate X‐ray absorption fine‐structure (XAFS) spectra of polycrystalline Ge powder with a glitch‐free energy range from ?200 to 800 eV relative to the Ge absorption edge are obtained using this method at high pressures up to 23.7 GPa, demonstrating the capability of PHL optics in eliminating the DAC glitches for high‐pressure XAFS experiments. This approach brings new possibilities to perform XAFS measurements using a DAC up to ultrahigh pressures.     

High‐flux hard X‐ray microbeam using a single‐bounce capillary with doubly focused undulator beam

A pre‐focused X‐ray beam at 12 keV and 9 keV has been used to illuminate a single‐bounce capillary in order to generate a high‐flux X‐ray microbeam. The BioCAT undulator X‐ray beamline 18ID at the Advanced Photon Source was used to generate the pre‐focused beam containing 1.2 × 10¹³ photons s^?1 using a sagittal‐focusing double‐crystal monochromator and a bimorph mirror. The capillary entrance was aligned with the focal point of the pre‐focused beam in order to accept the full flux of the undulator beam. Two alignment configurations were tested: (i) where the center of the capillary was aligned with the pre‐focused beam (`in‐line') and (ii) where one side of the capillary was aligned with the beam (`off‐line'). The latter arrangement delivered more flux (3.3 × 10¹² photons s^?1) and smaller spot sizes (≤10 µm FWHM in both directions) for a photon flux density of 4.2 × 10¹⁰ photons s^?1µm^?2. The combination of the beamline main optics with a large‐working‐distance (approximately 24 mm) capillary used in this experiment makes it suitable for many microprobe fluorescence applications that require a micrometer‐size X‐ray beam and high flux density. These features are advantageous for biological samples, where typical metal concentrations are in the range of a few ng cm^?2. Micro‐XANES experiments are also feasible using this combined optical arrangement.     

Nuclear Reactions under Irradiation of Deuterated Structures by X Rays

Measurements of emission from nuclear reaction products (neutrons and protons) have been carried out appearing in the deuterated structures of textured CVD diamond, palladium, titanium, and zirconium under irradiation with a beam of X rays using independent methods (neutron detector based on He-3 counters, Si surface-barrier semiconductor detectors and CR-39 track detector). The possibility of enhancement of both DD reaction and multi-particle deuterium fusion by the beam of X rays with energy ranging 20–30 keV in solid deuterated targets has been established. Analysis of X-ray fluorescence spectra of the target bombarded by beams of ions has revealed “additional” peaks, the occurrence of which cannot be related to any of the known elements, and requires separate study.

     

Ultra‐thin optical grade scCVD diamond as X‐ray beam position monitor

Results of measurements made at the SIRIUS beamline of the SOLEIL synchrotron for a new X‐ray beam position monitor based on a super‐thin single crystal of diamond grown by chemical vapor deposition (CVD) are presented. This detector is a quadrant electrode design processed on a 3 µm‐thick membrane obtained by argon–oxygen plasma etching the central area of a CVD‐grown diamond plate of 60 µm thickness. The membrane transmits more than 50% of the incident 1.3 keV energy X‐ray beam. The diamond plate was of moderate purity (～1 p.p.m. nitrogen), but the X‐ray beam induced current (XBIC) measurements nevertheless showed a photo‐charge collection efficiency approaching 100% for an electric field of 2 V µm^?1, corresponding to an applied bias voltage of only 6 V. XBIC mapping of the membrane showed an inhomogeneity of more than 10% across the membrane, corresponding to the measured variation in the thickness of the diamond plate before the plasma etching process. The measured XBIC signal‐to‐dark‐current ratio of the device was greater than 10⁵, and the X‐ray beam position resolution of the device was better than a micrometer for a 1 kHz sampling rate.     

The first microbeam synchrotron X‐ray fluorescence beamline at the Siam Photon Laboratory

The first microbeam synchrotron X‐ray fluorescence (µ‐SXRF) beamline using continuous synchrotron radiation from Siam Photon Source has been constructed and commissioned as of August 2011. Utilizing an X‐ray capillary half‐lens allows synchrotron radiation from a 1.4 T bending magnet of the 1.2 GeV electron storage ring to be focused from a few millimeters‐sized beam to a micrometer‐sized beam. This beamline was originally designed for deep X‐ray lithography (DXL) and was one of the first two operational beamlines at this facility. A modification has been carried out to the beamline in order to additionally enable µ‐SXRF and synchrotron X‐ray powder diffraction (SXPD). Modifications included the installation of a new chamber housing a Si(111) crystal to extract 8 keV synchrotron radiation from the white X‐ray beam (for SXPD), a fixed aperture and three gate valves. Two end‐stations incorporating optics and detectors for µ‐SXRF and SXPD have then been installed immediately upstream of the DXL station, with the three techniques sharing available beam time. The µ‐SXRF station utilizes a polycapillary half‐lens for X‐ray focusing. This optic focuses X‐ray white beam from 5 mm × 2 mm (H × V) at the entrance of the lens down to a diameter of 100 µm FWHM measured at a sample position 22 mm (lens focal point) downstream of the lens exit. The end‐station also incorporates an XYZ motorized sample holder with 25 mm travel per axis, a 5× ZEISS microscope objective with 5 mm × 5 mm field of view coupled to a CCD camera looking to the sample, and an AMPTEK single‐element Si (PIN) solid‐state detector for fluorescence detection. A graphic user interface data acquisition program using the LabVIEW platform has also been developed in‐house to generate a series of single‐column data which are compatible with available XRF data‐processing software. Finally, to test the performance of the µ‐SXRF beamline, an elemental surface profile has been obtained for a piece of ancient pottery from the Ban Chiang archaeological site, a UNESCO heritage site. It was found that the newly constructed µ‐SXRF technique was able to clearly distinguish the distribution of different elements on the specimen.     

The energy dispersive scheme of X‐ray fluorescence analysis with a crystal polarizer and polycapillary optics

The efficiency of the polarization scheme based on polycapillary optics and a diamond crystal polarizer was demonstrated. The scheme provides suppression of the background of scattered radiation in measuring X‐ray fluorescence spectra. A quasi‐parallel X‐ray beam with an angular divergence of 4.2 mrad was formed by a microfocus source with a copper anode and polycapillary half‐lens. Simultaneous polarization and monochromatization of radiation was obtained with a crystal of natural diamond, which was set at the diffraction reflection (113). The degree of polarization of CuK_α1 spectral line and the maximum radiation flux were respectively equal to 99.86% and 5 · 10⁶ photon/s. In the direction orthogonal to the plane of diffraction, the maximum attenuation of the background was up to 19 dB.     

Time lag as a characteristic feature in the identification of a moving object by a two‐detector X‐ray sensor

The authors conduct an experimental study of the dynamics of secondary (diffusely scattered and fluorescent) X‐ray radiation originating from the moving grains of minerals and offer a semi‐quantitative explanation for it. They compare the secondary radiation's amplitudes for the free falling grains of natural diamond and for its accompanying minerals that are changing over time. The signals are simultaneously registered by two detectors placed in the upper and lower spatial half‐planes relative to the horizontal flux of primary X‐ray radiation. The authors show that the time difference between the occurrence of dynamic signals' maximums in the detectors allows to identify the type of irradiated mineral. This time lag is negligibly small for a diamond but for the accompanying mineral it is close to its flight time through the irradiation zone. The authors have constructed and tested the laboratory model of a separator that showed a high degree of diamond extraction from the mixture of different minerals. Copyright © 2015 John Wiley & Sons, Ltd.     

Refraction and ultra‐small‐angle scattering of X‐rays in a single‐crystal diamond compound refractive lens

In this work a double‐crystal setup is employed to study compound refractive lenses made of single‐crystal diamond. The point spread function of the lens is calculated taking into account the lens transmission, the wavefront aberrations, and the ultra‐small‐angle broadening of the X‐ray beam. It is shown that, similarly to the wavefront aberrations, the ultra‐small‐angle scattering effects can significantly reduce the intensity gain and increase the focal spot size. The suggested approach can be particularly useful for the characterization of refractive X‐ray lenses composed of many tens of unit lenses.     

Characterization of laser processing of single‐crystal natural diamonds using micro‐Raman spectroscopic investigations

The application of lasers for processing diamond has revolutionized the diamond industry and its applications in microelectronics, microelectromechanical system (MEMS) and microoptoelectromechanical system (MOEMS) technologies. The process quality can be evaluated using spectroscopic techniques. In the present investigation, four different types of Q‐switched solid‐state lasers (with different beam parameters), namely, a lamp‐pumped Nd:YAG laser operating at 1064 nm, a lamp‐pumped Nd:YAG laser operating at second harmonically generated 532 nm, a diode‐pumped Nd:YVO₄ laser operating at 1064 nm and a diode‐pumped Nd:YAG laser operating at 1064 nm, have been employed for the processing of a single‐crystal, gem‐quality, natural diamond. The main objective behind the selection of these lasers with different beam parameters was to study the effect of wavelength, pulse width, pulse energy, peak power and beam quality factor (M² factor) on various aspects of processing (such as microcracking, material loss and cut surface quality) and their relative merits and demerits. The overall weight loss of the diamond and formation of microcracks during processing have been studied for the above four cases. The characteristics of the graphite formed during processing, elemental analysis, surface morphology of the cut surface and process dynamics have been studied using micro‐Raman spectroscopy and scanning electron microscopy (SEM). We observed that laser cutting of single‐crystal diamonds used for industrial applications can be accomplished without microcracking or surface distortion using Q‐switched Nd:YAG lasers. This allows direct processing without extensive postgrinding and polishing stages. Very efficient diamond processing is possible using diode‐pumped lasers, which results in the lowest possible breakage rate, good accuracy, good surface finish and low weight loss. From the micro‐Raman and SEM studies, it is concluded that the surface quality obtained is superior when diode‐pumped Nd:YVO₄ laser is used, owing to its extremely high peak power. The maximum graphite content is observed while processing with lamp‐pumped Nd:YAG laser at 532 nm. An overall comparison of all the laser sources leads to the conclusion that diode‐pumped Nd:YAG laser is a superior option for the efficient processing of natural diamond crystals. Copyright © 2006 John Wiley & Sons, Ltd.     

Polarization control of an X‐ray free‐electron laser with a diamond phase retarder

A diamond phase retarder was applied to control the polarization states of a hard X‐ray free‐electron laser (XFEL) in the photon energy range 5–20 keV. The horizontal polarization of the XFEL beam generated from the planar undulators of the SPring‐8 Angstrom Compact Free‐Electron Laser (SACLA) was converted into vertical or circular polarization of either helicity by adjusting the angular offset of the diamond crystal from the exact Bragg condition. Using a 1.5 mm‐thick crystal, a high degree of circular polarization, 97%, was obtained for 11.56 keV monochromatic X‐rays, whereas the degree of vertical polarization was 67%, both of which agreed with the estimations including the energy bandwidth of the Si 111 beamline monochromator.     

BioCARS: a synchrotron resource for time‐resolved X‐ray science

BioCARS, a NIH‐supported national user facility for macromolecular time‐resolved X‐ray crystallography at the Advanced Photon Source (APS), has recently completed commissioning of an upgraded undulator‐based beamline optimized for single‐shot laser‐pump X‐ray‐probe measurements with time resolution as short as 100 ps. The source consists of two in‐line undulators with periods of 23 and 27 mm that together provide high‐flux pink‐beam capability at 12 keV as well as first‐harmonic coverage from 6.8 to 19 keV. A high‐heat‐load chopper reduces the average power load on downstream components, thereby preserving the surface figure of a Kirkpatrick–Baez mirror system capable of focusing the X‐ray beam to a spot size of 90 µm horizontal by 20 µm vertical. A high‐speed chopper isolates single X‐ray pulses at 1 kHz in both hybrid and 24‐bunch modes of the APS storage ring. In hybrid mode each isolated X‐ray pulse delivers up to ～4 × 10¹⁰ photons to the sample, thereby achieving a time‐averaged flux approaching that of fourth‐generation X‐FEL sources. A new high‐power picosecond laser system delivers pulses tunable over the wavelength range 450–2000 nm. These pulses are synchronized to the storage‐ring RF clock with long‐term stability better than 10 ps RMS. Monochromatic experimental capability with Biosafety Level 3 certification has been retained.     

Momentum‐resolved resonant inelastic X‐ray scattering on a single crystal under high pressure

A single‐crystal momentum‐resolved resonant inelastic X‐ray scattering (RIXS) experiment under high pressure using an originally designed diamond anvil cell (DAC) is reported. The diamond‐in/diamond‐out geometry was adopted with both the incident and scattered beams passing through a 1 mm‐thick diamond. This enabled us to cover wide momentum space keeping the scattering angle condition near 90°. Elastic and inelastic scattering from the diamond was drastically reduced using a pinhole placed after the DAC. Measurement of the momentum‐resolved RIXS spectra of Sr_2.5Ca_11.5Cu₂₄O₄₁ at the Cu K‐edge was thus successful. Though the inelastic intensity becomes weaker by two orders than the ambient pressure, RIXS spectra both at the center and the edge of the Brillouin zone were obtained at 3 GPa and low‐energy electronic excitations of the cuprate were found to change with pressure.     

Simulations of X‐ray diffraction of shock‐compressed single‐crystal tantalum with synchrotron undulator sources

Polychromatic synchrotron undulator X‐ray sources are useful for ultrafast single‐crystal diffraction under shock compression. Here, simulations of X‐ray diffraction of shock‐compressed single‐crystal tantalum with realistic undulator sources are reported, based on large‐scale molecular dynamics simulations. Purely elastic deformation, elastic–plastic two‐wave structure, and severe plastic deformation under different impact velocities are explored, as well as an edge release case. Transmission‐mode diffraction simulations consider crystallographic orientation, loading direction, incident beam direction, X‐ray spectrum bandwidth and realistic detector size. Diffraction patterns and reciprocal space nodes are obtained from atomic configurations for different loading (elastic and plastic) and detection conditions, and interpretation of the diffraction patterns is discussed.     

X‐ray magnetic spectroscopy at high pressure: performance of SPring‐8 BL39XU

An X‐ray magnetic circular dichroism experiment under multiple extreme conditions, 2 ≤T≤ 300 K, H≤ 10 T and P≤ 50 GPa, has been achieved at SPring‐8 BL39XU. A combination of the high‐brilliant X‐ray beam and a helicity‐controlled technique enabled the dichroic signal to be recorded with high accuracy. The performance is shown by the outcome of pressure‐induced ferromagnetism in Mn₃GaC and the pressure‐suppressed Co moment in ErCo₂. Two technical developments, a tiny diamond anvil cell inserted into a superconducting magnet and in situ pressure calibration using 90° Bragg diffraction from a NaCl marker, are also presented. X‐ray magnetic spectroscopy under multiple extreme conditions is now opening a new approach to materials science.     

I19, the small‐molecule single‐crystal diffraction beamline at Diamond Light Source

The dedicated small‐molecule single‐crystal X‐ray diffraction beamline (I19) at Diamond Light Source has been operational and supporting users for over three years. I19 is a high‐flux tunable‐wavelength beamline and its key details are described in this article. Much of the work performed on the beamline involves structure determination from small and weakly diffracting crystals. Other experiments that have been supported to date include structural studies at high pressure, studies of metastable species, variable‐temperature crystallography, studies involving gas exchange in porous materials and structural characterizations that require analysis of the diffuse scattering between Bragg reflections. A range of sample environments to facilitate crystallographic studies under non‐ambient conditions are available as well as a number of options for automation. An indication of the scope of the science carried out on the beamline is provided by the range of highlights selected for this paper.