Understanding the junction degradation mechanism in CdS/CdTe solar cells using a Cd-deficient CdTe layer

It is known that CdTe solar cells are often degraded under solar illumination. But the degradation mechanism is not fully proved because it does not appear consistently. The junction degradation in CdS/CdTe solar cells was investigated using a CdTe layer with Cd deficient composition, where Cd vacancy concentration is high. It was found that the Cu atoms easily filled the Cd vacancies in CdTe and transport to junction area from Cu back contact. PL measurement and spectral quantum efficiency measurement showed that the incorporation of Cu atoms in CdS forms a defect energy level at 1.55 eV below the conduction band in CdS. As a result, the junction built-in potential is decreased and light penetration into CdTe absorber is shielded. For reliable and stable CdTe cells, the formation of Cd vacancy in CdTe should be avoided by careful control of CdTe.     

肖特基势垒对CdS/CdTe薄膜电池J-V暗性能的影响

采用数学模拟方法分析了不同背接触势垒高度(φ_b) 对于CdS/CdTe薄膜电池的J-V(电流密度-电压)方程的影响, 得出了势垒高度与roll-over的变化对应关系. 采用相应Cu/Mo背电极的CdS/CdTe薄膜电池在220-300 K的变温J-V曲线的数值分析与理论分析相对照, 分析了背势垒对于J-V曲线拟合参数的影响. 修正了φ_b 与反向饱和电流(J_b0)关系式, 理论与实验符合得非常好. 关键词： CdS/CdTe薄膜 伏安特性 肖特基势垒 roll-over     

Thermally evaporated CdS/CdTe thin film solar cells: Optimization of CdCl2 evaporation treatment on absorber layer

CdCl₂ treatment is crucial in the fabrication of highly efficient CdS/CdTe thin-film solar cells. This study reports a comprehensive analysis of thermal evaporated CdS/CdTe thin-film solar cells when the CdTe absorber layer is CdCl₂ annealed at temperatures from 340 to 440 °C. Samples were characterized for structural, optical, morphological and electrical properties. The films annealed at 400 °C showed better crystallinity with a cubic zinc blende structure having large grains. Higher refractive index, optical conductivity, and absorption coefficient were recorded for the CdTe films annealed at 400 °C with CdCl₂. Optimum photoactive properties for CdS/CdTe thin-film solar cells were also obtained when samples were annealed at 400 °C for 20 min with CdCl₂, and the best device exhibited V_OC of 668.4 mV, J_SC of 13.6 mA cm⁻², FF of 53.9% and an efficiency of 4.9%.     

Deep level transient spectroscopy investigation of deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact

Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep defects in the CdTe thin film. With the help of deep level transient spectroscopy (DLTS), we study the deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact. One hole trap and one electron trap are observed. The hole trap H1, localized at E_v+0.128~eV, originates from the vacancy of Cd (V_Cd. The electron trap E1, found at E_c-0.178~eV, is considered to be correlated with the interstitial Cu_i⁼ in CdTe.     

不同温度下制备的CdTe薄膜对太阳电池光电性能的影响

在不同温度下用近空间升华法（CSS）制备了CdTe多晶薄膜,结合I-V,C-V特性及深能级瞬态谱研究了不同温度制备的CdTe薄膜对CdS/CdTe太阳电池性能的影响.结果表明,制备温度对电池组件的开路电压影响不大,对短路电流和填充因子有影响,CdTe薄膜的深中心对温度和频率的响应基本一致.580℃制备的样品暗饱和电流密度最小,载流子浓度较高,光电特性较好,而且空穴陷阱浓度较低,深中心复合作用较小.在此研究基础上制备出了面积为300 mm×400 mm 关键词： 制备温度 CdTe薄膜 深能级瞬态谱（DLTS） CdS/CdTe太阳电池     

低强度飞秒激光激发下CdTe和CdTe/CdS核壳量子点的荧光上转换研究

利用400 nm和800 nm不同波长的低强度飞秒激光,对CdTe和CdTe/CdS核壳量子点溶胶进行激发,研究其稳态和时间分辨荧光性质.800 nm飞秒激光激发下,CdTe和CdTe/CdS核壳量子点产生上转换发光现象,上转换荧光峰与400 nm激发下的荧光峰相比蓝移最多达15 nm,而且蓝移值与荧光量子产率有关.变功率激发确认激发光功率与上转换荧光强度间满足二次方关系,时间分辨荧光的研究表明荧光动力学曲线服从双e指数衰减.提出表面态辅助的双光子吸收模型是低激发强度上转换发光的主要机理.CdTe和CdT 关键词： CdTe量子点 CdTe/CdS核壳量子点 时间分辨荧光 上转换荧光     

CdTe/CdS核壳结构量子点超快载流子动力学

在水相合成CdTe以及CdTe/CdS核壳结构量子点基础上, 利用基于抽运-探测技术的瞬态差分透射技术研究了CdTe量子点以及不同CdS壳层厚度的CdTe/CdS量子点的最低激子能态的超快激发与弛豫动力学. 研究表明:相比于CdTe,CdTe/CdS量子点的电子空穴由于空间分离,其所需的激发时间要长于电子空穴空间重叠态所需要的激发时间.随着壳层厚度的增加, 量子点表面的钝化有效地减少了表面态相关弛豫机理,并延长相对应的弛豫时间.     

CdS/CdTe薄膜太阳电池的深能级瞬态谱和光致发光研究

用深能级瞬态谱和光致发光研究了无背接触层的CdS/CdTe薄膜太阳电池的杂质分布和深能级中心.得到了净掺杂浓度在器件中的分布.确定了两个能级位置分别在E_V+0365 eV和E_V+0282 eV的深中心,它们的浓度分别为167×10¹² cm^-3和386×10¹¹ cm^-2,俘获截面分别为143×10^-14cm²和153×10^-16cm².它们来源于以化学杂质形式存在的Au和（或）Te_Cd^-复合体,或与氩氧气氛下沉积CdTe时的氧原子相关. 关键词： 深能级瞬态谱 光致发光 CdS/CdTe太阳电池     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

Enhancing the performance of thin film CdS/PbS photovoltaic solar cells

This work investigates dependence of the short-circuit current density, open-circuit voltage, fill factor and efficiency of a thin film CdS/PbS solar cell on thickness of transparent conductive oxide (TCO) layer, thickness of window layer (CdS), concentration of uncompensated acceptors (width of space-charge region), carrier lifetime in PbS and the reflectivity from metallic back contact. The effect of optical losses, front and rear recombination losses as well as the recombination losses on space-charge region are also considered in this study. As a result, by thinning the front contact layer indium tin oxide from 400 to 100 nm and window layer (CdS) from 200 to 100 nm it is possible to reduce the optical losses from 32 to 20%. The effect of electron lifetime on the internal and external quantum efficiency can be neglected at high width of the space-charge region. The maximum current density of 18.4 mA/cm² is achieved at wide space-charge region (concentration of uncompensated acceptors = 10¹⁵ cm^?3) and the longest lifetime (τ_n = 10^?6 s) where the optical and recombination losses are about 55%. The maximum efficiency of 5.17%, maximum open-circuit voltage of 417 mV and approximately fixed fill factor of 74% are yielded at optimum conditions such as: electron lifetime = 10^?6 s; concentration of uncompensated acceptors = 10¹⁶ cm^?3; thickness of TCO = 100 nm; thickness of CdS = 100 nm; velocity of surface and rear recombination = 10⁷ cm/s and thickness of absorber layer = 3 μm. When the reflectance from the back contact is 100%, the cell parameters improve and the cell efficiency records a value of 6.1% under the above conditions.     

Preparation of water-soluble CdTe/CdS core/shell quantum dots with enhanced photostability

CdTe/CdS core/shell quantum dots (QDs) have been synthesized in an aqueous phase using thioacetamide as a sulfur source. The quantum yield was greatly enhanced by the epitaxial growth of a CdS shell, which was confirmed by X-ray photoelectron spectroscopy (XPS) results. The quantum yield of as-prepared CdTe/CdS core/shell QDs without any post-preparative processing reached 58%. The experimental results illustrate that the QDs with core/shell structure show better photostability than thioglycolic acid (TGA)-capped CdTe QDs. The cyclic voltammograms reveal higher oxidation potentials for CdTe/CdS core/shell QDs than for TGA-capped CdTe QDs, which explains the superior photostability of QDs with a core/shell structure. This enhanced photostability makes these QDs with core/shell structure more suitable for bio-labeling and imaging.     

Performance improvement of CdS/Cu（In,Ga）Se2 solar cells after rapid thermal annealing

In this paper, we investigated the effect of rapid thermal annealing (RTA) on solar cell performance. An opto-electric conversion efficiency of 11.75% (Voc=0.64 V, Jsc = 25.88mA/cm2 , FF=72.08%) was obtained under AM 1.5G when the cell was annealed at 300℃ for 30s. The annealed solar cell showed an average absolute efficiency 1.5% higher than that of the as-deposited one. For the microstructure analysis and the physical phase confirmation, X-ray diffraction (XRD), Raman spectra, front surface reflection (FSR), internal quantum efficiency (IQE), and X-ray photoelectron spectroscopy (XPS) were respectively applied to distinguish the causes inducing the efficiency variation. All experimental results implied that the RTA eliminated recombination centers at the p-n junction, reduced the surface optical losses, enhanced the blue response of the CdS buffer layer, and improved the ohmic contact between Mo and Cu(In, Ga)Se2 (CIGS) layers. This leaded to the improved performance of CIGS solar cell.     

Recombination-induced voltage-dependent photocurrent collection loss in CdTe thin film solar cell

Recently, the efficiency of CdTe thin film solar cell has been improved by using new type of window layer Mg_xZn_1-xO (MZO). However, it is hard to achieve such a high efficiency as expected. In this report a comparative study is carried out between the MZO/CdTe and CdS/CdTe solar cells to investigate the factors affecting the device performance of MZO/CdTe solar cells. The efficiency loss quantified by voltage-dependent photocurrent collection efficiency (η_C(V')) is 3.89% for MZO/CdTe and 1.53% for CdS/CdTe solar cells. The higher efficiency loss for the MZO/CdTe solar cell is induced by more severe carrier recombination at the MZO/CdTe p—n junction interface and in CdTe bulk region than that for the CdS/CdTe solar cell. Activation energy (E_a) of the reverse saturation current of the MZO/CdTe and CdS/CdTe solar cells are found to be 1.08 eV and 1.36 eV, respectively. These values indicate that for the CdS/CdTe solar cell the carrier recombination is dominated by bulk Shockley—Read—Hall (SRH) recombination and for the MZO/CdTe solar cell the carrier recombination is dominated by the p—n junction interface recombination. It is found that the tunneling-enhanced interface recombination is also involved in carrier recombination in the MZO/CdTe solar cell. This work demonstrates the poor device performance of the MZO/CdTe solar cell is induced by more severe interface and bulk recombination than that of the CdS/CdTe solar cell.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

碲化镉薄膜太阳能电池电学特性参数分析

用inline方式全部近空间升华方法制备n-CdS/p-CdTe取得了～11%的转换效率(AM1.5). 把其中n-CdS层采用磁控溅射方法取得了～10%的转换效率(AM1.5). 基于其电流密度-电压(J-V)曲线和外量子效率曲线, 分析了其拟合关键参数对于电池性能的影响程度, 并从理论分析上把目前器件性能参数与当今前沿性能参数以及其理论值进行比较, 指出了如何提高电池转换效率(η)的方法: 提高开路电压(V_oc)、短路电流(J_sc)和填充因子(FF). 关键词： 碲化镉电池 电流密度-电压曲线 外量子效率曲线 电学特性     

Photoluminescence quenching of CdTe/CdS core-shell quantum dots in aqueous solution by ZnO nanocrystals

Photoluminescence (PL) properties of 3-mercaptopropionic acid (MPA) coated CdTe/CdS core-shell quantum dots (QDs) in aqueous solution in the presence of ZnO colloidal nanocrystals were studied by steady-state and time-resolved PL spectroscopy. The PL quenching of CdTe/CdS core-shell QDs with addition of purified ZnO nanocrystals resulted in a decrease in PL lifetime and a small red shift of the PL band. It was found that CdTe(1.5 nm)/CdS type II core-shell QDs exhibited higher efficiency of PL quenching than the CdTe(3.0 nm)/CdS type I core-shell QDs, indicating an electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals. The experimental results indicated that the efficient electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals could be controlled by changing the CdTe core size on the basis of the quantum confinement effect.     

界面修饰对有机-无机杂化钙钛矿太阳能电池性能的影响

作为近些年来最耀眼的明星材料之一,钙钛矿以其优异独特的光电特性成功吸引研究人员的广泛关注.自2009年报道了第一篇光电转换效率为3.8％的钙钛矿电池,到现在短短10年期间效率已经突破25.2％,几乎可以与商用多晶硅电池媲美.尽管其制备过程简单,但在薄膜的形成过程中很容易引入大量的缺陷.缺陷的存在会加速载流子的复合,阻碍...     

ZnS/CdS复合窗口层对CdTe太阳能电池短波光谱响应的影响

采用磁控溅射法制备了ZnS/CdS复合窗口层,并将其应用于CdTe太阳能电池。对所制备薄膜的形貌和结构等进行了研究。测试了具有不同窗口层的CdTe太阳电池的量子效率和光Ⅰ-Ⅴ特性,分析了ZnS薄膜制备条件对CdTe电池器件性能影响;研究了CdS薄膜厚度和ZnS/CdS复合窗口层对短波区透过率以及CdTe太阳电池的光谱响应的影响。着重研究了具有ZnS/CdS复合窗口层的CdTe太阳电池的短波光谱响应。结果表明,CdS窗口层厚度从100 nm减至50 nm后,其对短波区光子透过率平均提高了18.3%,CdTe太阳电池短波区光谱响应平均提高了27.6%。衬底温度250 ℃条件下制备的ZnS晶粒尺寸小于室温下制备的ZnS。具有ZnS/CdS复合窗口层的CdTe电池中,采用衬底温度250 ℃沉积ZnS薄膜来制备窗口层的电池器件,其性能要优于室温下沉积ZnS制备窗口层的电池器件。这说明晶粒尺寸的大小对电子输运有一定影响。在相同厚度CdS的前提下,具有ZnS/CdS复合窗口层的CdTe电池比具有CdS窗口层在短波的光谱响应提高了约2%。这说明ZnS/CdS复合窗口层能够做到减少对短波光子的吸收,从而使更多的光子被CdTe电池的吸收层吸收。     

钙钛矿/硅叠层太阳电池中平面a-Si:H/c-Si异质结底电池的钝化优化及性能提高

最近,旋涂法制备的钙钛矿/平面硅异质结高效叠层太阳电池引起人们广泛关注,主要原因是相比于绒面硅衬底制备的钙钛矿/硅叠层太阳电池,其制备工艺简单、制备成本低且效率高.对于平面a-Si:H/c-Si异质结电池, a-Si:H/c-Si界面的良好钝化是获得高转换效率的关键,进而决定了钙钛矿/硅异质结叠层太阳电池的性能.本文主要从硅片表面处理、a-Si:H钝化层和P型发射极等方面展开研究,通过对硅片表面的氢氟酸(HF)浸泡时间和氢等离子体预处理气体流量、a-Si:H钝化层沉积参数、钝化层与P型发射极(I/P)界面富氢等离子体处理的综合调控,获得了相应的优化工艺参数.对比研究了p-a-Si:H和p-nc-Si:H两种缓冲层材料对I/P界面的影响,其中高电导、宽带隙的p-nc-Si:H缓冲层既能够降低I/P界面的缺陷态,又可以增强P型发射层的暗电导率,提高了前表面场效应钝化效果.通过上述优化,制备出最佳的P-type emitter layer/aSi:H(i)/c-Si/a-Si:H(i)/N-type layer (inip)结构样品的少子寿命与implied-Voc分别达到2855μs和709 mV,表现出良好的钝化效果.应用于平面a-Si:H/c-Si异质结太阳电池,转换效率达到18.76%,其中开路电压达到681.5 mV,相对于未优化的电池提升了34.3 mV.将上述平面a-Si:H/c-Si异质结太阳电池作为底电池,对应的钙钛矿/硅异质结叠层太阳电池的开路电压达到1780 mV,转换效率达到21.24%,证明了上述工艺优化能够有效地改善叠层太阳电池中的硅异质结底电池的钝化及电池性能.     

CdTe太阳电池前电极SnO2:F/SnO2复合薄膜性能分析

减薄CdS窗口层是提高CdS/CdTe太阳电池转换效率的有效途径之一,减薄窗口层会对器件造成不利的影响,因此在减薄了的窗口层与前电极之间引入过渡层非常必要.利用反应磁控溅射法在前电极SnO₂:F薄膜衬底上制备未掺杂的SnO₂薄膜形成过渡层,并将其在N₂/O₂=4 ∶1,550 ℃环境进行了30 min热处理,利用原子力显微镜、X射线衍射仪、紫外分光光度计对复合薄膜热处理前后的形貌、结构、光学性能进行了表征,同时分析了复