Effect of annealing on the structural, optical and electrical properties of ZnO thin films by spray pyrolysis

Zinc oxide thin films have been deposited on glass substrates at a substrate temperature of 673 K by spray pyrolysis. The samples are annealed in ambient atmosphere at various temperatures. The effect of annealing on structural, electrical, and optical properties of ZnO films has been investigated. X-ray diffraction patterns show that crystallinity of the ZnO films has been improved after annealing. The morphology of ZnO thin films is studied by atomic force microscopy. The tensile strain (compressive stress) is found to decrease with increase in annealing temperature which indicates the relaxation of tensile strain in ZnO thin films. A decrease in energy band gap is observed with increase of annealing temperature. The mechanism of blue-green luminescence of ZnO thin film has been analyzed. The resistivity is found to decrease with annealing temperature.     

Structural modification and band gap engineering of sol–gel dip-coated thin films of Zn<Subscript>0.75</Subscript>Mg<Subscript>0.25</Subscript>O alloy under vacuum annealing

In the present study, we investigated the effect of vacuum annealing on the structural and optical properties of sol–gel dip-coated thin films of Zn_0.75Mg_0.25O alloy. XRD studies revealed that all these films were polycrystalline with hexagonal wurtzite structure and there was no trace of additional phases other than ZnO. With increase in annealing temperature, the samples showed preferred orientation along the c-axis, (0 0 2) plane and also peak narrowing and peak shift towards higher angles. The calculated values of mean crystallite size increased with annealing temperature indicating the improvement in crystallinity. Heat treatment caused lattice contraction and a decrease in film thickness. The optical transmittance in the visible spectral range enhanced with increase in annealing temperature while the fundamental absorption edge in the near ultra-violet region got red-shifted with annealing. The calculated values of optical energy gap of the samples showed a decrease with heat treatment due to the improvement in crystallinity during annealing and hence the subsequent decrease in quantum size effect.     

Effect of excimer laser annealing on the properties of ZnO thin film prepared by sol-gel method

Pristine ZnO thin films have been deposited with zinc acetate [Zn(CH₃COO)₂], mono-ethanolamine (stabilizer), and isopropanol solutions by sol-gel method. After deposition, pristine ZnO thin films have been irradiated by excimer laser (λ = 248, KrF) source with energy density of 50 mJ/cm² for 30 sec. The effect of excimer laser annealing on the optical and structural properties of ZnO thin films are investigated by photoluminescence and field emission scanning electron microscope. As-grown ZnO thin films show a huge peak of visible region and a wide full width at half maximum (FWHM) of UV region due to low quality with amorphous ZnO thin films. After KrF excimer laser annealing, ZnO thin films show intense near-band-edge (NBE) emission and weak deep-level emission. The optically improved pristine ZnO thin films have demonstrated that excimer laser annealing is novel treatment process at room temperature.     

Structural and optical properties of nanocrystalline ZnO thin films synthesized by the citrate precursor route

Nanocrystalline zinc oxide (ZnO) thin films have been deposited by spin-coating polymeric precursors synthesized by the citrate precursor route using ethylene glycol and citric acid as chelating agents. The ZnO thin films were annealed in air at different temperatures for 10 min. The films were characterized by different structural and optical techniques, including X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmission spectroscopy, and photoluminescence (PL). The thermal decomposition of polymeric precursor was studied by thermogravimetric analysis (TGA). XRD analysis with grazing incidence and rocking curves indicate that the ZnO films are polycrystalline with preferential orientation along the c-axis direction with a full-width at half-maximum (FWHM) of 0.31° for 600 °C-annealed samples. On annealing, the texturing in films increased along with a decrease in FWHM. AFM micrographs illustrate that the ZnO films are crack-free with well-dispersed homogeneous and uniformly distributed spherical morphology. The synthesized ZnO thin films have transparency >85% in the visible region exhibiting band edge at 375 nm, which becomes sharper with anneal. Room temperature PL spectra of these films show strong ultraviolet (UV) emission around 392 nm with an increase in intensity with annealing temperature, attributed to grain growth. Deconvolution of the PL spectra reveals that there is coupling of free excitons with higher orders of longitudinal optical (LO) phonon replicas leading to a broad asymmetric near-band-edge peak.     

Structural and photoluminescence characteristics of ZnO films by room temperature sputtering and rapid thermal annealing process

ZnO thin films deposited on SiO₂/Si substrates at room temperature by sputtering technology were annealed with a rapid thermal annealing process at various temperatures from 200 °C to 900 °C. The physical and optical properties of the ZnO films were investigated by X-ray diffraction, scanning electron microscopy and room-temperature photoluminescence (PL). The surface structures of the thin films showed great variations with increased annealing temperature. The PL spectrum illustrated that a stronger UV emission intensity appeared at an annealing temperature of 500 °C. On the other hand, visible-light emission could be obtained when the ZnO films were annealed above 500 °C and reached a maximum intensity at 900 °C. The possible mechanisms for visible-light emission are discussed. PACS 81.15.Cd; 81.40.Ef; 78.55.-m; 78.55.Et     

Effect of ZnO doping on the structural and optical properties of BaWO<Subscript>4</Subscript> thin films prepared using pulsed laser ablation technique

BaWO₄ doped with ZnO (2, 3, 5, 7 and 10 wt%) nanostructured films are prepared on quartz substrates by pulsed laser ablation. The films are post annealed at 900°C. GIXRD analysis of the post-annealed films reveal the change of orientation of scheelite tetragonal crystal growth from 1 1 2 reflection plane to 0 0 4 planes when doping concentration is more than 3 wt%. The AFM images show that film with 7 wt% ZnO doping concentration has good ceramic pattern with surface features giving a minimum value of rms surface roughness suitable for optoelectronic device applications. The optical transmittance and band-gap energy of the films are found to decrease considerably on postannealing which can be due to the increase in grain size of the crystallites on annealing. Thus doping with ZnO improves the surface features of the films and increases the optical band-gap energy.     

Effect of annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films on sapphire (0 0 0 1) substrates by magnetron sputtering

ZnO thin films were epitaxially grown on sapphire (0 0 0 1) substrates by radio frequency magnetron sputtering. ZnO thin films were then annealed at different temperatures in air and in various atmospheres at 800 °C, respectively. The effect of the annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films are investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL). A strong (0 0 2) diffraction peak of all ZnO thin films shows a polycrystalline hexagonal wurtzite structure and high preferential c-axis orientation. XRD and AFM results reveal that the better structural quality, relatively smaller tensile stress, smooth, uniform of ZnO thin films were obtained when annealed at 800 °C in N₂. Room temperature PL spectrum can be divided into the UV emission and the Visible broad band emission. The UV emission can be attributed to the near band edge emission (NBE) and the Visible broad band emission can be ascribed to the deep level emissions (DLE). By analyzing our experimental results, we recommend that the deep-level emission correspond to oxygen vacancy (V_O) and interstitial oxygen (O_i). The biggest ratio of the PL intensity of UV emission to that of visible emission (I_NBE/I_DLE) is observed from ZnO thin films annealed at 800 °C in N₂. Therefore, we suggest that annealing temperature of 800 °C and annealing atmosphere of N₂ are the most suitable annealing conditions for obtaining high quality ZnO thin films with good luminescence performance.     

Structural and optical properties of Au-implanted ZnO films

The structural and luminescence related optical behaviours of Au ion implanted ZnO films grown by magnetic sputtering and their post implantation annealing behaviours in the temperature range of 100-700 °C have been investigated. Optical absorption and transmittance spectra of the films indicate that band edge of Au-implanted ZnO has shifted to high energy range and optical band gap has increased, because the sharp difference of thermal expansion induces the lattice mismatch between ZnO and SiO₂. PL spectra reveal that UV and visible luminescence bands of ZnO films can be improved after thermal annealing due to recovery of defects and Au ions incorporation. Importantly, green luminescence band of 530 nm has been only observed in the Au-implanted and subsequently annealed ZnO films and it enhances with the increasing annealing temperature, which can be related to Au atoms or clusters in ZnO films. Furthermore, X-ray photoelectron spectroscopy measurements reveal that the Au⁰ is dominant state in Au implanted and annealed ZnO films. Possible mechanisms, such as optical transitions of Au atoms or clusters and deep level luminescence of ZnO, have been proposed for green emission.     

Effects of annealing on properties of ZnO thin films prepared by electrochemical deposition in chloride medium

The development of cost-effective and low-temperature synthesis techniques for the growth of high-quality zinc oxide thin films is paramount for fabrication of ZnO-based optoelectronic devices, especially ultraviolet (UV)-light-emitting diodes, lasers and detectors. We demonstrate that the properties, especially UV emission, observed at room temperature, of electrodeposited ZnO thin films from chloride medium (at 70 °C) on fluor-doped tin oxide (FTO) substrates is strongly influenced by the post-growth thermal annealing treatments. X-ray diffraction (XRD) measurements show that the films have preferably grown along (0 0 2) direction. Thermal annealing in the temperature range of 150-400 °C in air has been carried out for these ZnO thin films. The as-grown films contain chlorine which is partially removed after annealing at 400 °C. Morphological changes upon annealing are discussed in the light of compositional changes observed in the ZnO crystals that constitute the film. The optical quality of ZnO thin films was improved after post-deposition thermal treatment at 150 °C and 400 °C in our experiments due to the reducing of defects levels and of chlorine content. The transmission and absorption spectra become steeper and the optical bandgap red shifted to the single-crystal value. These findings demonstrate that electrodeposition have potential for the growth of high-quality ZnO thin films with reduced defects for device applications.     

Effect of post annealing temperature on structural and optical properties of ZnCdO thin films deposited by sol–gel method

Ternary ZnCdO thin films oriented along c-axis have been successfully deposited on p-Si (1 0 0) substrates using sol–gel spin coating route. To optimize most suitable annealing temperature for the Zn_1−xCd_xO thin films; these films with selected cadmium content x = 0.10 were treated at annealing temperatures from 300 °C up to 800 °C in oxygen ambient after deposition. The structural and optical properties of deposited thin films have been characterized by X-ray diffraction, energy dispersive spectroscopy, atomic force microscopy, UV–Vis spectroscopy, and photoluminescence spectra. The results show that the obtained films possess high crystallinity with wurtzite structure. The crystallite size, lattice parameters, lattice strain and stress in the deposited films are determined from X-ray diffraction analysis. The band gap energy increased as a function of annealing temperatures as observed from optical reflectance spectra of samples. The presence of Cd in the deposited films is confirmed by energy dispersive spectrum and it is observed that Cd re-evaporate from the lattice with annealing. The photoluminescence measurements as performed at room temperature did not exhibit any luminescence related to oxygen vacancies defects for lower annealing temperatures, as normally displayed by ZnO films. The green yellow luminescence associated to these defects was observed at higher annealing temperatures (≥700 °C).     

Effect of annealing temperature on the structural and optical properties of ZnO thin films prepared by sol–gel method

In this work, ZnO thin films were synthesized by sol–gel method on glass substrates followed by calcinations on different temperatures. The effect of annealing temperature on the structure and optical properties of the films was studied. The structural characteristics of the samples were analyzed by X-ray diffraction and atomic force microscope. The optical properties were studied by a UV-visible spectrophotometer. The results show that all the prepared ZnO thin films have a high preferential oriented c-axis orientation with compact hexagonal wurtzite structure. With the increasing annealing temperature (mse.ufl.edu), the intensity of (002) peak, particle size, surface RMS roughness, and absorbance of the ZnO thin films were increased as well. On the contrary, the transmittance and optical band gaps were decreased.     

Effects of annealing treatment on the formation of CO2 in ZnO thin films grown by metal-organic chemical vapor deposition

Post-growth annealing was carried out on ZnO thin films grown by metal-organic chemical vapor deposition (MOCVD). The grain size of ZnO thin film increases monotonically with annealing temperature. The ZnO thin films were preferential to c-axis oriented after annealing as confirmed by X-ray diffraction (XRD) measurements. Fourier transformation infrared transmission measurements showed that ZnO films grown at low temperature contains CO₂ molecules after post-growth annealing. A two-step reaction process has been proposed to explain the formation mechanism of CO₂, which indicates the possible chemical reaction processes during the metal-organic chemical vapor deposition of ZnO films.     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

Optical and electrical properties of plasma-oxidation derived HfO2 gate dielectric films

High-k gate dielectric HfO₂ thin films have been deposited on Si(1 0 0) by using plasma oxidation of sputtered metallic Hf thin films. The optical and electrical properties in relation to postdeposition annealing temperatures are investigated by spectroscopic ellipsometry (SE) and capacitance-voltage (C-V) characteristics in detail. X-ray diffraction (XRD) measurement shows that the as-deposited HfO₂ films are basically amorphous. Based on a parameterized Tauc-Lorentz dispersion mode, excellent agreement has been found between the experimental and the simulated spectra, and the optical constants of the as-deposited and annealed films related to the annealing temperature are systematically extracted. Increases in the refractive index n and extinction coefficient k, with increasing annealing temperature are observed due to the formation of more closely packed thin films and the enhancement of scattering effect in the targeted HfO₂ film. Change of the complex dielectric function and reduction of optical band gap with an increase in annealing temperature are discussed. The extracted direct band gap related to the structure varies from 5.77, 5.65, and 5.56 eV for the as-deposited and annealed thin films at 700 and 800 °C, respectively. It has been found from the C-V measurement the decrease of accumulation capacitance values upon annealing, which can be contributed to the growth of the interfacial layer with lower dielectric constant upon postannealing. The flat-band voltage shifts negatively due to positive charge generated during postannealing.     

在不同衬底上制备的ZnO薄膜透射率的研究

采用反应磁控溅射在不同结构衬底上生长ZnO薄膜,通过X-ray衍射(XRD)及透射光谱来分析薄膜的成膜情况,并得出在Al₂O₃/AlN复合基上溅射沉积的ZnO薄膜比单独在AlN薄膜衬底的结晶质量好且透过率也较高。而经不同的快速热退火温度验证,发现在400 ℃时,ZnO薄膜的结晶化及在(002)方向上的择优取向达到最好,并在可见光范围内的平均透过率达到88%以上。当退火温度超过450 ℃时,温度过高改变了ZnO薄膜的内部结构,使其氧原子和锌原子发生了较大距离的位移,导致薄膜内部缺陷的增多,从而存在过多的晶界,增加了其薄膜的散射机制,使光的透过性变差,退火温度为500 ℃时,薄膜的平均透过率为80%。     

Structure and properties of ZnO films grown on Si substrates with low temperature buffer layers

Zinc oxide (ZnO) thin films were grown on Si (1 0 0) substrates by pulsed laser deposition (PLD) using two-step epitaxial growth method. Low temperature buffer layer (LTBL) was initially deposited in order to obtain high quality ZnO thin film; the as-deposited films were then annealed in air at 700 °C. The effects of LTBL and annealing treatment on the structural and luminescent properties of ZnO thin film were investigated. It was found that tensile strain was remarkably relaxed by employing LTBL and the band-gap redshifted, correspondingly. The shift value was larger than that calculated from band-gap theories. After annealing treatment, it was found that the annealing temperature with 700 °C has little influence on strains of ZnO films with LTBLs other than directly deposited film in our experiments. Interestingly, the different behaviors in terms of the shift of ultraviolet (UV) emission after annealing between films with and without buffer were observed, and a tentative explanation was given in this paper.     

Effect of annealing temperature on the optical constants of zinc oxide films

In this paper, the effect of annealing temperature on optical constants was studied. The ZnO films were deposited on microscopic glass substrates using the sol-gel method for various annealing temperatures. The deposited zinc oxide (ZnO) films were characterized by an X-ray diffractometer (XRD), a spectrophotometer and scanning electron microscopy (SEM). The transmittance spectra recorded through the spectrophotometer exhibits 90% transmittance. The XRD spectra showed polycrystalline nature of ZnO film. Optical constants were determined through transmittance spectra using an envelope method. It was found that there was a significant effect of annealing temperature on the refractive index and extinction coefficient of deposited ZnO films. In this experiment, the optimum refractive index value of 1.97 was obtained at 350 °C annealing temperature at visible (vis) wavelength. The optical energy gap was found to be of ∼3.2 eV for all the samples. The top view of SEM showed the ZnO grain growth on the glass substrates.     

Surface morphology of ZnO buffer layer and its effects on the growth of GaN films on Si substrates by magnetron sputtering

ZnO thin films were first prepared on Si(111) substrates using a radio frequency magnetron sputtering system. Then the as-grown ZnO films were annealed in oxygen ambient at temperatures of 700, 800, 900, and 1000°C , respectively. The morphologies of ZnO films were studied by an atom force microscope (AFM). Subsequently, GaN epilayers about 500 nm thick were deposited on the ZnO buffer layers. The GaN/ZnO films were annealed in NH₃ ambient at 900°C. The microstructure, morphology and optical properties of GaN films were studied by x-ray diffraction (XRD), AFM, scanning electron microscopy (SEM) and photoluminescence (PL). The results are shown, their properties having been investigated particularly as a function of the ZnO layers. For better growth of the GaN films, the optimal annealing temperature of the ZnO buffer layers was 900°C.     

Controlled visible photoluminescence of ZnO thin films prepared by RF magnetron sputtering

ZnO thin films were prepared by RF magnetron sputtering. The photoluminescence dependence on the growth ambient and annealing temperatures and the atmosphere has been studied. Visible photoluminescence with blue, green, orange, and red emission bands has been demonstrated by controlling the preparation conditions. Complete suppression of the visible emission bands was also realized by annealing the O₂-ambient-grown samples in N₂ atmosphere at higher temperatures, which indicated the preparation of ZnO thin films with high optical quality.     

Reduction of dislocation density and improvement of optical quality in ZnO layers by MgO-buffer annealing

Optical properties of ZnO thin films with/without MgO-buffer annealing were investigated by low and room temperature photoluminescence measurements. The ZnO films were grown on c-sapphire substrates by plasma-assisted molecular-beam epitaxy employing a thin MgO-buffer layer. Dislocation density of ZnO layer was reduced from 5.3 × 10⁹ to 1.9 × 10⁹ cm⁻² by annealing MgO-buffer prior to the growth of ZnO. The intensity of free exciton emission from the sample with MgO-buffer annealing was almost twice of that from the sample without annealing, while the deep level emission from the sample with MgO-buffer annealing was about 1/3 of that without annealing. The MgO-buffer annealing improves optical quality of overgrown ZnO films.