掺AlZnO纳米线阵列的光致发光特性研究

采用化学气相沉积方法，以金做催化剂，在Si (100)衬底上制备了掺AlZnO纳米线阵列.扫描电子显微镜(SEM)表征发现ZnO纳米线的直径在30nm左右.X射线衍射(XRD)图谱上只存在ZnO的(002)衍射峰，说明ZnO纳米线沿c轴择优取向.掺AlZnO纳米线阵列的室温光致发光(PL)谱中出现了3个带边激子发射峰：373nm，375nm，389nm.运用激子理论推算出掺AlZnO纳米线的禁带宽度为3.343eV ，束缚激子结合能为0.156eV；纯ZnO纳米线阵列PL谱中3个带边激子发射 关键词： 光致发光 化学气相沉积(CVD) 激子 ZnO纳米线阵列     

Electronic band structure and optical properties of silicon nanoporous pillar array

Silicon nanoporous pillar array (Si-NPA) is fabricated by hydrothermally etching single crystal silicon (c-Si) wafers in hydrofluoric acid containing ferric nitrate. Microstructure studies disclosed that it is a typical micron/nanometer structural composite system with clear hierarchical structures. The optical parameters of Si-NPA were calculated by general light-absorption theory and Kramers–Kronig relations based on the experimental data of reflectance and the variations compared with the counterparts of c-Si were analyzed. The features of the electronic band structure deduced from the optical measurements strongly indicate that Si-NPA material is a direct-band-gap semiconductor and possesses separated conduction sub-bands which accords with conduction band splitting caused by silicon nanocrystallites several nanometers in size. All these electronic and optical results are due to the quantum confinement effect of the carriers in silicon nanocrystallites.     

Superhydrophobic surfaces fabricated by microstructuring of stainless steel using a femtosecond laser

Fabrication of superhydrophobic surfaces induced by femtosecond laser is a research hotspot of superhydrophobic surface studies nowadays. We present a simple and easily-controlled method for fabricating stainless steel-based superhydrophobic surfaces. The method consists of microstructuring stainless steel surfaces by irradiating samples with femtosecond laser pulses and silanizing the surfaces. By low laser fluence, we fabricated typical laser-induced periodic surface structures (LIPSS) on the submicron level. The apparent contact angle (CA) on the surface is 150.3°. With laser fluence increasing, we fabricated periodic ripples and periodic cone-shaped spikes on the micron scale, both covered with LIPSS. The stainless steel-based surfaces with micro- and submicron double-scale structure have higher apparent CAs. On the surface of double-scale structure, the maximal apparent CA is 166.3° and at the same time, the sliding angle (SA) is 4.2°.     

Evolution of groups with a hierarchical structure

The universal occurrence of a hierarchical structure and its dynamic behavior in various types of group, living or abstract, are discussed. Here the word “group” refers not only to tangible aggregation but also to invisible aggregation of social psychological and of geopolitical meaning. The evolution of these groups is simulated using a model of agents distributed on the lattices of cellular grids. It is assumed that agents, fearing isolation, interact asymmetrically with each other with regard to exchange of “power”. As an indicator of hierarchy, the Gini coefficient is introduced. Example calculations are made for the aggregation, fusion and fission of animal groups, and for the appearance of a powerful empire and the rise and fall of supremacy. It is shown that such abstract objects evolve with time in accordance with the universal rules of groups common to birds and fish.     

氧化锌/硅纳米孔柱阵列的结构和光致发光特性研究

以硅纳米孔柱阵列(Si-NPA)为衬底、用化学气相沉积法制备了具有规则阵列结构特征的ZnO/Si-NPA纳米复合体系，并对其结构和光致发光性质进行了表征. 实验结果显示，组成ZnO/Si-NPA表面阵列的每个柱子均呈现层壳结构. 不同于衬底Si-NPA的红光和蓝光发射，ZnO/Si-NPA在紫外光区和蓝绿光区呈现出两个强的宽发光峰. 分析表明，紫外光发射应归因于ZnO晶体的带边激子跃迁；而蓝绿光发射则来自于ZnO晶体本征缺陷所形成的两类深能级复合中心上载流子的辐射跃迁.     

Superhydrophobic hierarchical surfaces fabricated by anodizing of oblique angle deposited Al-Nb alloy columnar films

A combined process of oblique angle magnetron sputtering and anodizing has been developed to tailor superhydrophobic surfaces with hierarchical morphology. Isolated submicron columns of single-phase Al-Nb alloys are deposited by magnetron sputtering at several oblique deposition angles on a scalloped substrate surface, with the gaps between columns increasing with an increase in the deposition angle from 70° to 110°. Then, the columnar films have been anodized in hot phosphate-glycerol electrolyte to form a nanoporous anodic oxide layer on each column. Such surfaces with submicron-/nano-porous structure have been coated with a fluoroalkyl phosphate layer to reduce the surface energy. The porous surface before coating is superhydrophilic with a contact angle for water is less than 10°, while after coating the contact angles are larger than 150°, being superhydrophobic. The beneficial effect of dual-scale porosity to enhance the water repellency is found from the comparison of the contact angles of the submicron columnar films with and without nanoporous oxide layers. The larger submicron gaps between columns are also preferable to increase the water repellency.     

Preparation of hybrid film with superhydrophobic surfaces based on irregularly structure by emulsion polymerization

A superhydrophobic surface originated from quincunx-shape composite particles was obtained by utilizing the encapsulation and graft of silica particles to control the surface chemistry and morphology of the hybrid film. The composite particles make the surface of film form a composite interface with irregular binary structure to trap air between the substrate surface and the liquid droplets which plays an essential role in obtaining high water contact angle and low water contact angle hysteresis. The water contact angle on the hybrid film is determined to be 154 ± 2° and the contact angle hysteresis is less than 5°. This is expected to be a simple and practical method for preparing self-cleaning hydrophobic surfaces on large area.     

Characterization of optoelectronic properties of the ZnO nanorod array using surface photovoltage technique

Well-aligned ZnO nanorod array, synthesized by wet chemical bath deposition (CBD) method on conductive indium-in-oxide (ITO) substrate, was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. Surface photovoltage (SPV) technique based on a scanning Kelvin Probe system was employed to investigate the optoelectronic behavior of ZnO nanorod array. The surface photovoltage and its time-resolved evolution process are used to determine the energy level structure of the ZnO nanorod array.     

用PAA模板法实现硅基纳米孔阵列结构

用二次阳极氧化方法制备出分立、双向贯通并且超薄（500—1000 nm）的多孔阳极氧化铝膜,贴合到硅片上进行干法刻蚀,实现图形转移,得到了硅基纳米孔阵列结构,并对工艺中影响图形转移质量的因素进行了探索.扫描电镜（SEM）测试结果表明该途径得到的纳米结构孔形态均匀且大面积有序,孔深度可达到125 nm.对该样品进行热氧化处理后进行光致发光（PL）测试,结果表明其光致发光机理是基于通常较微弱的TO声子辅助的硅带边发光,并实现了显著发光增强,对这种增强效果的物理机理进行了理论分析.该结构具有的独特光学特性为利用 关键词： 多孔阳极氧化铝模板 硅基纳米孔阵列结构 图形转移     

Synthesis and photocatalytic property of ZnSe flowerlike hierarchical structure

Spherical flowerlike hierarchical structure of ZnSe(en)_0.5 was synthesized via a solvothermal route in the NH₃·H₂O-ethylenediamine (en)-N₂H₄·H₂O system at 180 °C for 24 h. The hierarchical structure is assembled from lots of regular nanosheets. The ZnSe(en)_0.5 was further converted into pure hexagonal ZnSe by annealing in a flowing nitrogen gas at 500 °C for 1 h with morphology preserved. The formation mechanism of ZnSe was discussed. The UV-visible absorption spectrum and PL spectrum of the ZnSe spherical flowerlike hierarchical structure were measured. In addition, photocatalytic activity of the ZnSe flowerlike structure for the degradation of methyl orange under the irradiation of the simulated sunlight was investigated. The excellent catalytic activity for the degradation of methyl orange was found and the possible mechanism of the photocatalytic activity is also proposed.     

Repeller structure in a hierarchical model. II. Metric properties

We study the renormalization dynamics deriving from a hierarchical tight-binding Schrödinger equation. In the Part I of this work we analyzed the topological structure of the recurrent set-a chaotic repeller- and its relation with the spectral problem. In this part we turn our attention to the metric properties of the repeller. We first study periodic orbits and their bifurcation unfolding, and we organize them on a binary tree. We then apply a thermodynamic formalism which provides a complete characterization of the scaling properties of the energy spectrum. The distributionf() of local dimensions is determined by computing both a generalized -function through the periodic orbits and the bandwidths of periodic approximants of the Schrödinger operator. When the growth rateR of the potential is smaller than 1, we find evidence of a phase transition, implying that two different classes of states coexist in the spectrum. The asymptotic behavior of the Lebesgue measure of the spectrum is also studied. A linear scaling of to 0 is observed forR 1_–, while forR > 1, the measure of the periodic approximants goes to 0 as R^–h with the hierarchical orderh. Finally, we show that the localized state, present for R<1, is characterized by a superexponential scaling of the bandwidth.     

A hierarchical structure with improved OMP sparse representation used with face recognition

With the rapid development of the face recognition technology, more and more optical products are applied in people's real life. The recognition accuracy can be improved by increasing the number of training samples, but the colossal training samples will result in the increase of computational complexity. In recent years, sparse representation method becomes a research hot spot on face recognition. In this paper we propose an energy constrain orthogonal matching pursuit (ECOMP) algorithm for sparse representation to select the few training samples and a hierarchical structure for face recognition. We filter the training samples with ECOMP algorithm and then we compute the weights by all selected training samples. At last we find the closest recovery sample to the test sample. Simultaneously the experimental results in AR, ORL and FERET database also show that our proposed method has better recognition performance than the LRC and SRC_OMP method.     

Modular and hierarchical structure of social contact networks

Social contact networks exhibit overlapping qualities of communities, hierarchical structure and spatial-correlated nature. We propose a mixing pattern of modular and growing hierarchical structures to reconstruct social contact networks by using an individual’s geospatial distribution information in the real world. The hierarchical structure of social contact networks is defined based on the spatial distance between individuals, and edges among individuals are added in turn from the modular layer to the highest layer. It is a gradual process to construct the hierarchical structure: from the basic modular model up to the global network. The proposed model not only shows hierarchically increasing degree distribution and large clustering coefficients in communities, but also exhibits spatial clustering features of individual distributions. As an evaluation of the method, we reconstruct a hierarchical contact network based on the investigation data of a university. Transmission experiments of influenza H1N1 are carried out on the generated social contact networks, and results show that the constructed network is efficient to reproduce the dynamic process of an outbreak and evaluate interventions. The reproduced spread process exhibits that the spatial clustering of infection is accordant with the clustering of network topology. Moreover, the effect of individual topological character on the spread of influenza is analyzed, and the experiment results indicate that the spread is limited by individual daily contact patterns and local clustering topology rather than individual degree.     

Fabrication of superhydrophobic surface of hierarchical ZnO thin films by using stearic acid

Flower-like hierarchical ZnO microspheres were successfully synthesized by a simple, template-free, and low-temperature aqueous solution route. The morphology and microstructure of the ZnO microspheres were examined by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The bionic films with hydrophobicity were fabricated by the hierarchical ZnO microspheres modified by stearic acid. It was found that the hydrophobicity of the thin films was very sensitive to the added amount of stearic acid. The thin films modified with 8% stearic acid took on strong superhydrophobicity with a water contact angle (CA) almost to be 178° and weak adhersion. The remarkable superhydrophobicity could be attributed to the synergistic effect of micro/nano hierarchical structure of ZnO and low surface energy of stearic acid.     

Electrospinning fabrication of rime-like NiO nanowires/nanofibers hierarchical architectures and their photocatalytic properties

Rime-like NiO Nanowires/nanofibers hierarchical architectures have been fabricated employing a co-precipitation reaction and electrospinning method. The synthesized hierarchical structure was characterized using SEM, XRD and BET analysis methods. The effects of growth temperature and reaction time on the morphologies of the as-prepared structures were investigated by SEM characterization and a possible mechanism for the formation of NiO hierarchical structures is proposed. Based on the nitrogen adsorption and desorption measurements, the BET surface area of the as-obtained sample is 61.0 m²/g and the pore sizes of ca. 5.0 nm. The catalytic efficiency of the NiO nanomaterials developed was evaluated by the photocatalytic degradation of acetaldehyde. In comparison with sphere-like and fiber-like structures, the NiO hierarchical structures show an excellent ability to rapidly acetaldehyde pollutant, which may be attributed to its unique hierarchical and porous surface structures.     

Synthesis and room-temperature NO_2 gas sensing properties of a WO_3 nanowires/porous silicon hybrid structure

We report on the fabrication and performance of a room-temperature NO2 gas sensor based on a WO3 nanowires/porous silicon hybrid structure. The W18O49 nanowires are synthesized directly from a sputtered tungsten film on a porous silicon （PS） layer under heating in an argon atmosphere. After a carefully controlled annealing treatment, WO3 nanowires are obtained on the PS layer without losing the morphology. The morphology, phase structure, and crystallinity of the nanowires are investigated by using field emission scanning electron microscopy （FESEM）, X-ray diffractometer （XRD）, and high-resolution transmission electron microscopy （HRTEM）. Comparative gas sensing results indicate that the sensor based on the WO3 nanowires exhibits a much higher sensitivity than that based on the PS and pure WO3 nanowires in detecting NO2 gas at room temperature. The mechanism of the WO3 nanowires/PS hybrid structure in the NO2 sensing is explained in detail.     

柱状ZnO阵列薄膜的生长及其发光特性

采用一种设备简单、原料低廉的新型方法，在镀有ZnO先驱薄膜的(0001)蓝宝石上利用水热 法制备出了柱状ZnO阵列薄膜.用扫描电镜(SEM)，X射线衍射(XRD)对样品的形貌和结构进行 了表征，结果显示ZnO薄膜为柱状阵列，基于蓝宝石衬底沿c轴择优生长，且(0004)摇摆曲线 半高宽度(FWHM)约为1.8°.此ZnO阵列薄膜具有很强的紫外发射光谱(PL). 关键词： 柱状ZnO阵列薄膜 水热法 (0001)蓝宝石 PL谱     

Growth and properties of InGaAs nanowires on silicon

Free‐standing ternary InGaAs nanowires (NW) are at the core of intense investigations due to their integration capabilities on silicon (Si) for next‐generation photovoltaics, integrated photonics, tunneling devices, and high‐performance gate all‐round III–V/Si NW transistors. In this review, recent progress on the growth, structural, optical and electrical properties of InGaAs NWs on Si substrate is highlighted. Particular focus is on a comparison between conventional catalyst‐assisted and catalyst‐free growth methods as well as self‐assembled versus site‐selectively grown NW arrays. It will be shown that catalyst‐free, high‐periodicity NW arrays with extremely high compositional uniformity are mandatory to allow un‐ambiguous structure–property correlation measurements. Here, interesting insights into the electronic/optical properties of wurtzite, zincblende and mixed crystal phases of InGaAs will be highlighted based on recent photoluminescence spectroscopy data. Finally, the InGaAs NW‐on‐Si system is also discussed in the realms of heterojunction properties, providing a promising system for steep‐slope tunneling field effect transistors in future low‐power post‐CMOS intergrated microelectronics and broad‐band photoabsorption and detec‐tion devices. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Superhydrophobic surfaces via controlling the morphology of ZnO micro/nano complex structure

ZnO micro/nano complex structure films, including reticulate papillary nodes, petal-like and flake-hole, have been self-assembled by a hydrothermal technique at different temperatures without metal catalysts. The wettability of the above film surfaces was modified with a simple coating of heptadecafluorodecyltrimethoxy-silane in toluene. After modifying, the surface of ZnO film grown at 50~${^\circ}$C was converted from superhydrophilic with a water contact angle lower than 5$^{\circ}$ to superhydrophobic with a water contact angle of 165$^{\circ}$. Additionally, the surface of reticulate papillary nodes ZnO film grown at 100~${^\circ}$C had excellent superhydrophobicity, with a water contact angle of 173$^{\circ}$ and a sliding angle lower than 2$^{\circ}$. Furthermore, the water contact angle on the surface of petal-like and flake-hole ZnO films grown at 150~${^\circ}$C and 200~${^\circ}$C were found to be 140$^{\circ}$ and 120$^{\circ}$, respectively. The wettability for the samples was found to depend strongly on the surface morphology which results from the growth temperature.     

激光扫描阵列结构增强不锈钢与塑料的连接强度

本文采用光纤激光器在不锈钢表面上制备圆形阵列结构来增强不锈钢与塑料的连接强度。研究了激光制备的圆形阵列结构参数以及连接参数对不锈钢与塑料连接强度的影响。结果表明,不锈钢表面经过激光扫描构形处理后能显著提高不锈钢与塑料的连接强度,在压力作用下,熔融塑料渗入激光构造微孔形成的机械互锁是增强不锈钢与塑料连接强度的主要机制。激光构形后不锈钢表面上的毛刺高度、数量以及覆盖率对连接接头的连接强度有重要影响。毛刺高度为10~20μm,毛刺数量占比Tm小于14.82%时,不锈钢与塑料在连接面处断裂,剪切力随着Tm的增加而增加;当Tm值高于14.82%时,在塑料处断裂,且剪切力数值在塑料的平均拉伸断裂力(950 N)上下浮动。不锈钢与塑料连接接头断裂于塑料处时所对应的最小覆盖率为38.5%,此时剪切力为900 N。此外,激光扫描处理过程中不锈钢与塑料连接的温度与压力对连接强度有重要影响,在加热温度为400℃时,不锈钢与塑料连接接头的剪切力最强;当压力为75 kN时,不锈钢与塑料连接接头的剪切力最强。