脉冲超声激励下SonoVue微泡的瞬态空化特性

将SonoVue微泡从临床疾病诊断拓展至治疗引起了诸多研究人员的兴趣。为了平衡治疗效率和生物安全性,深入理解声学参数和SonoVue微泡瞬态空化的关系至关重要。本研究自行制备仿体容器放置SonoVue微泡,使用1 MHz发射换能器激励其产生空化效应,另一个7.5 MHz的聚焦换能器接收声信号,经放大及高速数据采集后送上位机处理。通过深入分析信号的时频域特征,我们提出以宽带信号的能量及其随时间变化曲线的半高宽来表征瞬态空化的剂量(ICD)和相对持续时间(ICP),并确定:瞬态空化的发生和ICD依赖于峰值负声压,但ICP随峰值负声压的增加而减小;脉冲重复频率和脉冲持续时间都和ICD及ICP正相关;且脉冲持续时间的影响较大。这些结果有望为SonoVue微泡的治疗应用提供理论支持。      

流动微泡群瞬态空化强度时域分布的比例反馈调节*

声波、血流环境及流动微泡群的稳定性都会影响焦区内瞬态空化强度(ICI)在超声作用时间内的分布,从而影响基于瞬态空化的治疗效率和生物安全性。本文在搭建仿体中流动微泡群瞬态空化发生和实时测量系统的基础上,设计了基于LabView FPGA的比例反馈控制器,在保持脉冲重复频率和脉冲长度不变的条件下,通过选择适当的比例系数,依据当前周期的声波激励下实时测量的ICI,实时调节下一周期声波信号的峰值负压,以调控ICI在时间上的分布。研究表明,在最优比例系数(1 × 107)下,和开环系统相比,ICI的稳定率提升~2.31 倍,ICI的时域下降速率减小~94.41%;在超声作用时间内总ICI也基本达到期望水平。这些结果表明该比例反馈控制器在调控脉冲超声激励下流动微泡群ICI时域分布的有效性,有望改进瞬态空化在相关疾病治疗中的效率和安全性。     

高强度聚焦超声场中空化泡群的结构及其形成过程

空化是高强度聚焦超声(HIFU)引起组织损伤的作用机制之一。本文使用高速摄影技术研究了HIFU场中空化泡群结构的空间分布特征、超声功率对空化泡群结构的影响、空化泡群结构的建立过程尤其是起始过程。空化泡群的结构以空化泡在声场中的区域化分布为特征．在一定功率范围内空化泡群的结构保持稳定。从建立过程来看,空化泡群首先出现在焦区,然后在焦后区(远离换能器的区域)形成,焦前区(靠近换能器的区域)空化泡群最后形成。在对空化泡群起始的研究中发现最初拍摄到的空化泡群形状与焦区形状接近,并且观察到空化泡在焦区发生聚集然后破裂的现象。     

调频超声脉冲驱动微气泡运动偏移的研究

提出调频超声辐射力技术驱动微泡群,以加强微泡的吸附效率.基于改进的RP方程及粒子轨迹方程研究了微泡群整体的运动位移与调频信号的中心频率、调频范围、信号声压,以及微泡半径分布关系.研究结果表明调频信号在驱动半径具有宽泛分布的气泡群,以及半径分布远离谐振半径的气泡群时,作用效果好于传统正弦波信号.例如中心频率1 MHz、调频范围0.75 MHz的调频脉冲作用高斯分布（平均半径3.5 μm、均方差为1）的微泡群200 μs,可比同等声压的正弦波多约12%的微气泡产生位移30 μm. 关键词： 超声辐射力 调频波 高斯分布     

经颅聚焦超声联合微泡开放血脑屏障的数值仿真研究

近年大鼠等动物实验表明经颅聚焦超声联合微泡技术可无创开放血脑屏障实现药物递送,但在临床治疗时由于人体头颅非均质结构及其高声衰减特性,需优化超声经颅聚焦参数和微泡参数。本文基于人头颅CT数据、82阵元相控换能器和血管建立了三维数值仿真模型,研究超声及微泡参数对机械指数和靶区声发射的影响,评估血脑屏障开放程度及组织损伤的可能性。结果表明,声功率和微泡初始密度增大,机械指数和宽带噪声强度增大;频率增大,稳态空化强度增大;当微泡初始半径大于5μm时,稳态空化显著增强。该研究结果为经颅聚焦超声联合微泡技术诱导可控的BBB开放及安全有效递送治疗药物提供了理论数据和技术参考。     

考虑水蒸气蒸发和冷凝的球状泡群中泡的动力学特性

为了深入探究空化泡群中气泡的动力学特性,建立了超声驱动下考虑水蒸气的蒸发和冷凝的泡群中泡的动力方程.基于该方程,研究了泡群中泡的位置、泡的数量、泡的初始半径对其动力学特性的影响,探究了超声作用下球状泡群中气泡半径、能量、温度、压力和气泡内水蒸气分子数的变化规律.结果表明:泡群中泡的运动受到周围气泡的抑制作用;泡群中泡的初始半径大小对泡群中泡的半径、能量、温度、压力和气泡内水蒸气分子数有显著影响;泡群中泡的位置距离泡群中心越远,泡的膨胀半径越大;随着泡群中泡的数目增加,泡的振幅减小;超声频率增加,泡群中泡的空化效应减弱;超声声压增加,泡群中泡的空化效应增加.研究结果为超声空化泡群的研究提供了理论参考.     

超声药物释放空化动力学行为研究

以直径1 μm的脂质体为空化研究对象,从修正的Rayleigh空化方程入手,研究机械系数(MI)对300 kHz和1 MHz超声作用时空化效应的影响。脂质体的药物释放以超声作用前后脂质体中钙黄绿素的荧光强度为量度。模拟结果表明:在微泡振荡过程中,由超声波驱动产生的负向最大泡壁运动速度促使微泡半径从最大快速减小接近于零,微泡积聚到最大能量。对于300 kHz和1 MHz的激励超声,存在一个拐点(MI)值,当MI小于接近0.4时,1 MHz微泡半径变化幅度强于300 kHz;当MI>0.4时,300 kHz微泡半径变化幅度强于1 MHz。这一结果预示在此范围内,300 kHz的药物释放效果好于1 MHz。本研究为超声空化效应研究及超声药物释放应用提供了理论依据。     

微泡对高强度聚焦超声声压场影响的仿真研究*

微泡对高强度聚焦超声(HIFU)治疗焦域具有增效作用,而HIFU治疗中不同声学条件下微泡对HIFU形成声压场的影响尚不清楚。本文基于气液混合声波传播方程、Keller气泡运动方程、时域有限差分(FDTD)法和龙格-库塔(RK)法数值仿真研究输入声压、激励频率、气泡初始空隙率和气泡初始半径对HIFU形成声压场的影响。研究结果表明,随着输入声压的增大,焦点处声压升高但焦点处最大声压与输入声压的比值减小,焦点位置几乎不变;随着激励频率和气泡初始半径的增大,焦点处声压升高且焦点位置向远离换能器方向移动;随着气泡初始空隙率的增大,焦点处声压降低且焦点位置向换能器方向移动。     

声驻波场中空化泡的动力学特性

以水为工作介质, 考虑了液体的可压缩性, 研究了驻波声场中空化泡的运动特性, 模拟了驻波场中各位置处空化泡的运动状态以及相关参数对各位置处空化泡在主Bjerknes力作用下运动方向的影响. 结果表明: 驻波声场中, 空化泡的运动状态分为三个区域, 即在声压波腹附近空化泡做稳态空化, 在偏离波腹处空化泡做瞬态空化, 在声压波节附近, 空化泡在主Bjerknes 力作用下, 一直向声压波节处移动, 显示不发生空化现象; 驻波场中声压幅值增加有利于空化的发生, 但声压幅值增加到一定上限时, 压力波腹区域将排斥空化泡, 并驱赶空化泡向压力波节移动, 不利于空化现象的发生; 当声频率小于初始空化泡的共振频率时, 声频率越高, 由于主Bjerknes 力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生, 尤其是驻波场液面的高度不应是声波波长的1/4; 当声频率一定时, 空化泡初始半径越大越有利于空化现象的发生, 但当空化泡的初始半径超过声频率的共振半径时, 由于主Bjerknes力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生.     

基于Omega涡识别方法的诱导轮内非定常空化流动分析

为精确捕捉诱导轮中空化的行为特征并揭示其非定常流动机理,采用大涡模拟(LES)对一凝水泵诱导轮在设计工况、临界空化数下单独进行数值分析。基于Omega涡识别方法,对诱导轮内空化流动的流动结构及空化泡的关系进行研究。结果表明,Omega涡识别技术可以很好反映流动结构(剪切流与旋转流)与空化泡的关系：设计流量、临界空化数下,诱导轮叶片入口附近空化泡主要集中在轮缘附近的回流区内,回流区内部流动主要以剪切流的形式存在;而在流道中的回流区内流动主要以旋转运动为主,且空化泡主要集中在回流区与主流的剪切层区。     

Improving temporal stability of stable cavitation activity of circulating microbubbles using a closed-loop controller based on pulse-length regulation

Stable cavitation (SC) has shown great potential for novel therapeutic applications. The spatiotemporal distribution of the SC activity of microbubbles circulating in a target region is not only correlated with the uniformity of treatment, but also with some undesirable effects. Therefore, it is important to achieve controllable and desirable SC activity in target regions for improved therapeutic efficiency and biosafety. This study proposes a closed-loop feedback controller based on pulse length (PL) regulation to improve the temporal stability of SC activity. Microbubbles circulating in a physiological flowing phantom were exposed to a 1 MHz focused transducer. The SC signals produced were initially received by another 7.5 MHz plane transducer, followed by high-speed signal acquisition and real-time processing. Based on the real-time-measured SC intensity excited by the current acoustic pulse, the proposed closed-loop feedback controller used three proportional coefficients to regulate the peak negative pressure (PNP) and PL of the next acoustic pulse during the acceleration and stable stages, respectively. The results show that the rise time and the temporal stability of the SC intensity of the microbubbles circulating in these two stages were improved significantly by the optimized proportional coefficients used in the proposed controller. Importantly, when compared with the traditional closed-loop feedback controller based on PNP regulation, the proposed closed-loop feedback controller based on PL regulation reduced the probability of a transition between stable and inertial cavitation, thus avoiding the risk of disadvantageous bioeffects in practical applications. These results demonstrate the effectiveness of the proposed PL-based closed-loop feedback controller and provide a feasible strategy for realization of controllable cavitation activity in applications.     

Evaluation of the properties of daughter bubbles generated by inertial cavitation of preformed microbubbles

Inertial cavitation (IC) of the preformed microbubbles is being investigated for ultrasound imaging and therapeutic applications. However, microbubbles rupture during IC, creating smaller daughter bubbles (DBs), which may cause undesired bioeffects in the target region. Thus, it is important to determine the properties of DBs to achieve controllable cavitation activity for applications. In this study, we theoretically calculated the dissolution dynamics of sulfur hexafluoride bubbles. Then, we applied a 1-MHz single tone burst with different peak negative pressures (PNPs) and pulse lengths (PLs), and multiple 5-MHz tone bursts with fixed acoustic conditions to elicit IC of the preformed SonoVue microbubbles and scattering of DBs, respectively. After the IC and scattering signals were received by a 7.5-MHz transducer, time- and frequency-domain analysis was performed to obtain the IC dose and scattering intensity curve. The theoretical dissolution curves and measured scattering intensity curves were combined to determine the effect of the incident pulse parameters on the lifetime, mean radius and distribution range of DBs. Increased PNP reduced the lifetime and mean size of the DBs population and narrowed the size distribution. The proportion of small DBs (less than resonance size) increased from 36.83% to 85.98% with an increase in the PNP from 0.6 to 1.6 MPa. Moreover, increased PL caused a shift of the DB population to the smaller bubbles with shorter lifetime and narrower distribution. The proportion of small bubbles increased from 25.74% to 95.08% as the PL was increased from 5 to 100 µs. Finally, increased IC dose caused a smaller mean size, shorter lifetime and narrower distribution in the DB population. These results provide new insight into the relationship between the incident acoustic parameters and the properties of DBs, and a feasible strategy for achieving controllable cavitation activity in applications.     

Precise spatial control of cavitation erosion in a vessel phantom by using an ultrasonic standing wave

In atherosclerotic inducement in animal models, the conventionally used balloon injury is invasive, produces excessive vessel injuries at unpredictable locations and is inconvenient in arterioles. Fortunately, cavitation erosion, which plays an important role in therapeutic ultrasound in blood vessels, has the potential to induce atherosclerosis noninvasively at predictable sites. In this study, precise spatial control of cavitation erosion for superficial lesions in a vessel phantom was realised by using an ultrasonic standing wave (USW) with the participation of cavitation nuclei and medium-intensity ultrasound pulses. The superficial vessel erosions were restricted between adjacent pressure nodes, which were 0.87 mm apart in the USW field of 1 MHz. The erosion positions could be shifted along the vessel by nodal modulation under a submillimetre-scale accuracy without moving the ultrasound transducers. Moreover, the cavitation erosion of the proximal or distal wall could be determined by the types of cavitation nuclei and their corresponding cavitation pulses, i.e., phase-change microbubbles with cavitation pulses of 5 MHz and SonoVue microbubbles with cavitation pulses of 1 MHz. Effects of acoustic parameters of the cavitation pulses on the cavitation erosions were investigated. The flow conditions in the experiments were considered and discussed. Compared to only using travelling waves, the proposed method in this paper improves the controllability of the cavitation erosion and reduces the erosion depth, providing a more suitable approach for vessel endothelial injury while avoiding haemorrhage.     

Sonochemiluminescence observation and acoustic detection of cavitation induced by pulsed HIFU at a tissue–fluid interface

The aim of this study is to investigate the mechanism of the erosion process induced by 1.2 MHz pulsed high-intensity focused ultrasound (pulsed HIFU). By using Sonochemiluminescence (SCL) photograph, the initiation and maintenance of active cavitation were observed. In order to understand the role of both inertial cavitation and stable cavitation, a passive cavitation detection (PCD) transducer was used. Since the exposure variables of HIFU are important in the controlled ultrasound tissue erosion, the influence of pulse length (PL) and duty cycle (DC, T_on:T_off) has been examined. The results of tissue hole, SCL observation and acoustic detection revealed that the erosion was highly efficient for shorter PL. For higher DCs, the area of SCL increased with increasing PL. For lower DCs, the area of SCL increased with increasing PL from 10 to 20 μs and then kept constant. For all PLs, the intensity of SCL decreased with lower DC. For all DCs, the intensity of SCL per unit area (the ratio of SCL intensity to SCL area) also decreased with increasing PL from 10 to 80 μs, which suggested that the higher the intensity of SCL is, the higher the efficiency of tissue erosion is. At DC of 1:10, the position of the maximum pixel in SCL pictures was distant from the tissue–fluid interface with the increasing PL because of shielding effect. By the comparison of inertial cavitation dose (ICD) and the stable cavitation dose (SCD), the mechanisms associated with inertial cavitation are very likely to be the key factor of the erosion process.     

Characterising the chemical and physical properties of phase-change nanodroplets

Phase-change nanodroplets have attracted increasing interest in recent years as ultrasound theranostic nanoparticles. They are smaller compared to microbubbles and they may distribute better in tissues (e.g. in tumours). They are composed of a stabilising shell and a perfluorocarbon core. Nanodroplets can vaporise into echogenic microbubbles forming cavitation nuclei when exposed to ultrasound. Their perfluorocarbon core phase-change is responsible for the acoustic droplet vaporisation. However, methods to quantify the perfluorocarbon core in nanodroplets are lacking. This is an important feature that can help explain nanodroplet phase change characteristics. In this study, we fabricated nanodroplets using lipids shell and perfluorocarbons. To assess the amount of perfluorocarbon in the core we used two methods, ¹⁹F NMR and FTIR. To assess the cavitation after vaporisation we used an ultrasound transducer (1.1 MHz) and a high-speed camera. The ¹⁹F NMR based method showed that the fluorine signal correlated accurately with the perfluorocarbon concentration. Using this correlation, we were able to quantify the perfluorocarbon core of nanodroplets. This method was used to assess the content of the perfluorocarbon of the nanodroplets in solutions over time. It was found that perfluoropentane nanodroplets lost their content faster and at higher ratio compared to perfluorohexane nanodroplets. The high-speed imaging indicates that the nanodroplets generate cavitation comparable to that from commercial contrast agent microbubbles. Nanodroplet characterisation should include perfluorocarbon concentration assessment as critical information for their development.     

Study of a peak in cavitation activity from HIFU exposures using TA fluorescence

Methods of measuring the sound field and focal region of a 1.05 MHz high intensity focused ultrasound (HIFU) are described in this paper. 1.05 MHz pulsed HIFU with intensity 2400 W/cm(2) with a 1:1 duty cycle ("on" phase equaled "off" phase) was used to irradiate terephthalic acid (TA). Pulse periods of 0.5 ms, 1 ms, 3.3 ms, 10 ms, 15 ms, 33 ms, 0.1s and 1s were used. The irradiation time was 2 min. To indicate the intensity of inertial cavitation activity, the fluorescence intensity of hydroxyterephthalic acid (HTA) was measured. The result shows that the cavitation activity of pulsed HIFU peaks at a pulse period of 10 ms, cavitation activity is significantly greater for pulse periods from 2 to 20 ms than for others.     

超声造影剂微泡非线性动力学响应的机理及相关应用

随着生命科学及现代医学的发展, 一体化无创精准诊疗已经日益成为人们关注的焦点问题, 而关于超声造影剂微泡的非线性效应的相关机理、动力学建模及其在超声医学领域中的应用研究也得到了极大的推动. 本文对下列课题进行了总结和讨论, 包括: 1)基于Mie散射技术和流式细胞仪对造影剂微泡参数进行定征的一体化解决方案; 2)通过对微泡包膜的黏弹特性进行非线性修正, 构建新的包膜微泡动力学模型; 3)探索造影剂惯性空化阈值与其包膜参数之间的相关性; 以及4)研究超声联合造影剂微泡促进基因/药物转染效率并有效降低其生物毒性的相关机理.     

Study on the lifetime and attenuation properties of microbubbles coated with carboxylic acid salts

Four kinds of surfactants, sodium laurate, sodium myristate, sodium palmitate and sodium oleate were used to study the effects of surfactant coatings on the lifetime and attenuation of microbubbles. The changes in the size distribution of microbubbles prepared with these surfactants in saline were measured with a Coulter Multisizer (Coulter Electronics Ltd., Luton, UK). Frequency characteristics of ultrasonic attenuation of the microbubble suspensions were measured between 400 kHz and 6 MHz. From the changes in attenuation in the microbubble suspensions over time, it was found that the lifetime of microbubbles in a suspension also depends on the frequency of the irradiating ultrasound. The effect of surfactants on the frequency characteristics of attenuation was also studied, and characteristics of the surfactant coating, including shell elasticity and shell friction parameters were calculated from the measurement results. Microbubbles produced with sodium palmitate had the longest lifetime and the smallest average size. The shell had very little effect on the ultrasonic properties of microbubbles produced with sodium palmitate, suggesting that the sodium palmitate microbubbles behaved ultrasonically as free microbubbles.