Determination of cobalt,molybdenum and vanadium in austrian mineral waters by ICP-AES after ion-exchange separation and preconcentration

A method is described for the determination of cobalt, molybdenum and vanadium in mineral water samples by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) after separation of these elements from the matrix by ion exchange. The samples are acidified with concentrated hydrochloric acid (10 ml/l) and the elements are adsorbed as thiocyanate complexes. Elution is performed with a mixture 2M in perchloric acid and 1M in hydrochloric acid and subsequently with 1M hydrochloric acid. After evaporation of the eluates and dissolution of the residue the volume of the measuring solution for ICP-AES is 10 ml. The recoveries for Co, Mo and V at a concentration level of 1 g/1 in mineral waters were approximately 99%. A concentration factor of 100 is achieved by this procedure.     

负载硫杂杯芳烃树脂微柱分离富集-火焰原子吸收法测定痕量金

建立了大孔径树脂D101负载硫杂杯芳烃树脂微柱分离富集-火焰原子吸收光谱法测定痕量金的新方法。探讨了负载硫杂杯芳烃树脂对金的吸附原理与最佳条件。该法对金的检出限为0.23 ng/mL(3σ,n=11),线性范围为0.01~1μg/mL。对0.2μg/mL的Au 标液进行5次测定,RSD=2.1%,加标回收率在98.4%~103.3%之间。方法用于矿渣样中痕量金的分析。     

Molybdenum determination in iron matrices by ICP-AES after separation and preconcentration using polyurethane foam

A procedure is proposed for the separation and determination of molybdenum in iron matrices by a batch process. It is based on the solid-phase extraction of the molybdenum(V) ion as thiocyanate complex on polyurethane (PU) foam. The extraction parameters were optimized. Using 0.20 mol L-1 hydrochloric acid, a thiocyanate concentration of 0.10 mol L-1, 100 mg of polyurethane foam and shaking time of 10 min, molybdenum (5-400 micrograms) can be separated and preconcentrated from large amounts of iron (10 mg). Desorption was carried out instantaneously by conc. nitric acid or acetone. Distribution coefficients, sorption capacity of the PU foam and coefficients of variation were also evaluated. The effect of some ions on the separation procedure was assessed. Iron(III) should be reduced to iron(II). The proposed procedure was used to determine molybdenum in standard iron matrices such as steel and pure iron. The achieved results did not show significant differences with certified values.     

Molybdenum determination in iron matrices by ICP-AES after separation and preconcentration using polyurethane foam

A procedure is proposed for the separation and determination of molybdenum in iron matrices by a batch process. It is based on the solid-phase extraction of the molybdenum(V) ion as thiocyanate complex on polyurethane (PU) foam. The extraction parameters were optimized. Using 0.20 mol L^–1 hydrochloric acid, a thiocyanate concentration of 0.10 mol L^–1, 100 mg of polyurethane foam and shaking time of 10 min, molybdenum (5–400 μg) can be separated and preconcentrated from large amounts of iron (10 mg). Desorption was carried out instantaneously by conc. nitric acid or acetone. Distribution coefficients, sorption capacity of the PU foam and coefficients of variation were also evaluated. The effect of some ions on the separation procedure was assessed. Iron(III) should be reduced to iron(II). The proposed procedure was used to determine molybdenum in standard iron matrices such as steel and pure iron. The achieved results did not show significant differences with certified values.     

Determination of ten rare-earth elements and yttrium in silicate rocks by ICP-AES without separation and preconcentration

Lanthanum, cerium, neodymium, samarium, europium, gadolinium, dysprosium, erbium, ytterbium, lutetium and yttrium have been determined in 8 international rock standards by inductively coupled plasma atomic emission spectrometry (ICP-AES) without prior ion-exchange separation and preconcentration. The results for La, Ce, Nd, Eu, Dy, Yb and Y were in good agreement with the reported values, whereas those for Sm, Gd, Er and Lu were less accurate. However, the results for Sm, Gd, Er and Lu can also be used for studies of petrogenesis.     

Determination of noble metals after separation and preconcentration with silica-bonded complexing ligands

Noble metals are preconcentrated and separated from the matrix elements by adsorption on proper complexing ligands immobilized on silica gel and subsequent elution. Preconcentration factors of 5–10 were achieved. The reliability of the method was proved by analysis of a spiked soil material and a CRM with ICP-AES and ICP-MS. Ag, Au, Pd and Pt showed a good recovery in the spiked material. The indicative value for gold in the CRM (145 BCR) could be confirmed.     

交联壳聚糖分离富集-火焰原子吸收法测定水样中痕量银

以甲醛、环硫氯丙烷为交联剂,由壳聚糖合成了一种新型的交联壳聚糖微球(FCCIS)分离树脂,研究了不同条件下FCCTS对Ag(Ⅰ)的吸附性能.在pH 3.6时FCCTS对Ag(Ⅰ)定量吸附,吸附在树脂上的Ag(Ⅰ)可用0.5 moL/L的氨水将其洗脱,用火焰原子吸收光谱测定.该法对Ag(Ⅰ)的检出限为61 ng/mL(3σ,n=8),相对标准偏差为2.2%(n=7,ρ=2μg/mL),线性范围为0.05～4μg/mL,加标回收率在98.8%～101.7%之间.该法已用于水样中痕量银测定.     

Determination of molybdenum in extracts of soil and sewage sludge CRMs after fractionation by means of BCR modified sequential extraction procedure

A modified three-step sequential extraction procedure proposed by the Commission of European Communities Bureau of Reference (BCR) was applied to certified reference materials of three different soil groups (rendzina, luvisol, and cambisol) and sewage sludge of different compositions originating from a municipal water treatment plant in order to assess potential mobility and the distribution of molybdenum in the resulting fractions. In the soils examined, molybdenum was present almost entirely in the mineral lattice, the content of molybdenum in the fractions of the studied reference materials of sludges was predominant in the fraction, represents Mo bound to organic matter and sulphide.The internal check of accuracy was performed on the results of the sequential extraction by comparing of the extractable amounts of molybdenum in the sequential procedure with the results of the pseudototal digestion of original samples. The recovery ranged from 96 to 101% and the precision (RSD) in the extracts was below 10%.     

Determination of cadmium in water by ICP-AES with on-line adsorption preconcentration using DPTH-gel and TS-gel microcolumns

Two flow injection inductively coupled plasma atomic emission spectrometric methods for the preconcentration and determination of trace amounts of cadmium in sea-water and waste-water samples are described based on the adsorption of the metal ion on a micro-column placed in the injection valve of the FI manifold and packed with silica gel funtionalised with 1,5-bis(di-2-pyridyl) methylene thiocarbohydrazide (DPTH-gel) and silica gel functionalised with methylthiosalicylate (TS-gel), respectively. Various parameters and chemical variables affecting the preconcentration and determination of this metal by ICP-AES are evaluated. The DPTH-gel preconcentration method has a linear calibration range from 5 to at least 100 ng ml(-1) of cadmium, with a R.S.D. of 1.1% for ten independent analyses of 100 ng ml(-1), a detection limit of 1.1 ng ml(-1) and a throughput of 40 samples per hour using a 60 s preconcentration time. The TS-gel preconcentration method shows a linear range between 10 and 100 ng ml(-1), with a R.S.D. of 2.5% for ten independent analyses of 100 ng ml(-1), a detection limit of 4.3 ng ml(-1) and a sample throughput of 24 samples per hour for a preconcentration time of 120 s. Validation was carried out against a certified reference water sample and by determining the analyte content in spiked synthetic sea-water, sea-water and waste-water.     

Determination of 232Th in seawater by ICP-MS after preconcentration and separation using a chelating resin

This article describes an analytical method for the separation, preconcentration and determination of ²³²Th in seawater samples at sub-ng/L levels using a NOBIAS CHELATE PA1 resin and a sector field (SF) inductively coupled plasma mass spectrometer (ICP-MS). The resin showed excellent adsorption of ²³²Th at a low pH of 2.4 ± 0.4 in a relatively small volume (200 mL) of seawater. ²³²Th adsorbed on the resin was easily eluted using 5 mL of 0.8 M HNO₃. An enrichment factor of 40 was achieved for ²³²Th analysis. Ethylenediamine-tetraacetic acid disodium salt dehydrate (EDTA) was used to investigate the effect of ²³²Th-binding organic ligand on the retention of ²³²Th on the chelating resin. Results obtained using acidified samples (pH of 2.4 ± 0.4) showed EDTA had no significant effect on ²³²Th recovery, indicating that at this low pH, ²³²Th was dissociated from the ²³²Th-binding organic ligand and quantitatively retained on the NOBIAS CHELATE PA1 resin. The developed analytical method was characterized by a separation and preconcentration taking approximately 4 h and a low detection limit of 0.0038 ng/L for ²³²Th, and was successfully applied to the determination of ²³²Th in seawater samples collected from coastal areas, Japan.     

Determination of nickel in biological samples by ETA-AAS and ICP-AES after acidic dissolution (with microwave heating and preconcentration by liquid-liquid extraction)

The determination of nickel by ETA-AAS and ICP-AES in biological samples with prior extraction into methyl isobutyl ketone with 1,5-bis(di-2-pyridylmethylene) thiocarbonohydrazide as extracting reagent is described. Microwave dissolution in closed teflon vessels has been used for the dissolution of biological materials. At least three samples can be decomposed simultaneously with a preset heating programme. Results of analyses of some certified biological reference materials are given.     

Determination of heavy metals by inductively coupled plasma mass spectrometry after on-line separation and preconcentration

A method for the determination of Cu, As, Se, Cd, In, Hg, Tl, Pb and Bi in waters and in biological materials by inductively coupled plasma mass spectrometry, after an on-line separation, is described. The matrix separation and analyte preconcentration is accomplished by retention of the analytes complexed with the ammonium salt of O,O-diethyl dithiophosphoric acid in a HNO₃ solution on C₁₈ immobilized on silica in a minicolumn. Methanol, as eluent, is introduced in the conventional pneumatic nebulizer of the instrument. In order to use the best compromise conditions, concerning the ligand and acid concentrations, the analytes were determined in two separate groups. The enrichment factors were in the range from 5 to 61, depending on the analyte. The limits of detection varied from 0.43 ng L⁻¹ for Bi to 33 ng L⁻¹ for Cu. The sample consumption is only 2.3 mL for each group and the sampling frequency is 21 h⁻¹. The accuracy was tested by analysing five certified reference materials: water, riverine water, urine, bovine muscle and bovine liver. The agreement between obtained and certified concentrations was very good, except for As. The relatively small volume of methanol, used as eluent, minimizes the problems produced by the introduction of organic solvent into the plasma.     

Determination of trace amounts of gold in acid-attacked environmental samples by atomic absorption spectrometry with electrothermal atomization after preconcentration

A method for determination of trace amounts of gold in environmental samples (rocks, soils, sediments, and waters) by atomic absorption spectrometry with electrothermal atomization (ETAAS) after preconcentration using a chelating sorbent Spheron Thiol 1000 is described. The method accurately determines gold between 0.001 and several tens of grams per ton in samples having complex variations in mineralogy. Pulverized samples are roasted at 650°C to oxidize any sulfide and/or carbonaceous material. Samples are then subjected to a series of acid treatments to eliminate any silica matrix and to dissolve the sample. The Spheron Thiol 1000 is added to the sample solution, and then with sorbed gold is filtered out, washed, and ignited at 550°C. The residue is dissolved in aqua regia, evaporated, dissolved in distilled water, transferred to a volumetric flask, and analyzed by ETAAS.The limits of detection of gold, based on the 3 definition, were 0.5 ng g^–1 for 10-g samples (rocks, sediments, soils) and 0.05 ng mL^–1 for 1-L water samples. Precision of determination expressed by the relative standard deviation varied from 2.9% to 16.4%. The accuracy of the method is verified by analysis of certified reference materials. The obtained analytical results are in good agreement with attested values. The developed method was applied for gold determination in environmental samples affected by the acidification (acid mine drainage which is mainly a product of pyrite oxidation) from an open quartzite mine in the obov region situated NE of the city of Banská tiavnica (Slovakia).     

Determination of gold in natural waters by neutron activation and γ-spectrometry after preconcentration with tributyl phosphate as solid extractant

A method for the preconcentration of gold in natural waters at the sampling site using tributyl phosphate as a solid extractant [Se(TBP)] was developed as a preliminary step prior to the determination of gold by neutron activation and γ-spectrometry. The SE(TBP) was saturated with gaseous chlorine for extracting all gold species. In batch experiments gold was quantitatively retained on the SE(TBP) in 10 min. After extraction and washing, the SE(TBP) was ashed or back-extracted. Gold was quantitatively eluted with hot, neutral 0.025 M thiourea. The gold content of residues of ashing or eluents after evaporation was determined by neutron activation and γ-spectrometry. The detection limit for the overall procedure was 0.2 ng 1^?1. The efficiency was tested on ‘equilibrated’ solutions prepared from river water and tracer solutions of gold. For comparison, the gold content of natural water samples was determined using preconcentration on activated charcoal.     

纳米SiO_2分离富集-火焰原子吸收法测定水中痕量银

研究了纳米SiO_2分离富集-火焰原子吸收法测定水中痕量银的新方法.考察了溶液pH、吸附时间、洗脱条件和干扰离子等因素对Ag~+分离富集的影响,确定了纳米SiO_2对Ag~+吸附的最佳条件.结果表明:在pH 4.1时,纳米SiO_2能定量吸附银,吸附在纳米SiO_2上的Ag~+可用0.5 mol/L HCl+0.5 mol/L硫脲定量洗脱.该法对银的检出限为0.77 ng/mL(3σ,n=11);线性范围为0.005～1.5μg/mL,对0.5μg/mL的Ag~+标液进行7次测定,RSD为3.6%,回收率在94.0%～101.5%之间;方法可用于环境水样中痕量银的测定.     

Application of a macroporous resin containing imidazoline groups to preconcentration and separation of gold, platinum and palladium prior to ICP-AES determination

A new functional resin with a long functional side chain was synthesized by modification of aminated macroporous poly(vinyl chloride) resin with cyanoethylene and ethylenediamine. Traces of Au(III), Pt(IV) and Pd(II) in aqueous solution were quantitatively adsorbed in the acidity range of pH 4 and C(H(+)) 3 M. The rate of equilibration is high; Cu(2+), Fe(3+), Ni(2+), etc. exhibit little interference on the adsorption of the sought noble metals. The saturated adsorption capacities for Au(III), Pt(IV), Pd(II) and Ir(IV) in 2 M HCl were 4.0, 1.57, 2.26, 1.85 mmol g(-1). Adsorbed ions can be quantitatively desorbed by 4% thiourea +0.25 M H(2)SO(4). The resin has good reusability, and can be used for preconcentration and separation of Au(III), Pt(IV) and Pd(II) prior to their determination by ICP-AES with satisfactory results.     

Determination of neptunium using high resolution sequential ICP-AES

In view to separate La(III), Pr(III) and U(VI) ions, from aqueous solutions, batch experiments are carried out for the sorption and desorption of these ions onto and from a novel functionalized resin. The sorption capacities varied from 1.06 to 47.30 mg/g and increased in the following order La(III), Pr(III) and U(VI), while yields desorption ranged from 73.0 to 94.3% and increased in the following order Pr(III), La(III) and U(VI). Considering the largest difference in sorption capacity and desorption yield of these three elements, at different operates conditions, this material can be potential candidate for the separation of U(VI), Pr(III) and La(III) ions from nuclear and other industrial wastewater.     

密闭消解ICP-AES测定土壤及沉积物中主量和微量元素

利用高压密闭消化系统,采用王水-H2O2和HF-HNO3-H2O2两种消化液消化土壤标准物质GBW07403和GBW07404,用ICP-AES测定,研究土壤元素的测定方法。结果表明,土壤中的Al、As、Ca、Cr、Cd、Co、K、Cu、Fe、Mg、Mn、Na、Mo、Ni、P、Pb、Zn测定值与给定的标准值吻合,两种消化液测定值的相对标准偏差均小于2.6%。     

Determination of trace amounts of vanadium by UV-vis spectrophotometric after separation and preconcentration with modified natural clinoptilolite as a new sorbent

Natural clinoptilolite was used as a sorbent material for solid phase extraction and preconcentration of vanadium. The clinoptilolite was first saturated with a cation such as nickel(II) and then modified with benzyldimethyltetradecyleammonium chloride (BDTA) for increasing sorption of 4-(2-pyridylazo)resorcinol (PAR). Vanadium–PAR complex was quantitatively retained on the sorbent by the column method at the pH range 6.2–7.0 at a flow rate of 1 mL min⁻¹. It was removed from the column with 5.0 mL of dimethylformamide solution at a flow rate of 0.8 mL min⁻¹ and determined by UV–vis spectrophotometry at λ_max = 550 nm. 0.031 μg of vanadium can be concentrated from 450 mL of aqueous sample (where detection limit as 0.07 ng mL⁻¹ with preconcentration factor of 90). Relative standard deviation for eight replicate determination of 5.0 μg of vanadium in final solution is 2.1%. The interference of number of anions and cations has been studied in detail to optimize the conditions and method was successfully applied for determination of all vanadium as V(IV) form in standard samples.     

Determination of tungsten and tin ions after preconcentration by flotation

A highly sensitive and selective combined method of flotation followed by spectrophotometry/d.c. polarography for the determination of tungsten and tin ions in acid and alkaline waste waters and hydrometallurgical solutions is presented here. Both kinds of ions are coprecipitated in the analyte solution with zirconium hydroxide after addition of ZrOCl₂ solution and ammonia. Afterwards, the collector precipitate is separated from the aqueous phase and preconcentrated by flotation for which sodium oleate and a frother are added. The precipitate is dissolved in a small amount of acid, with the organic reagents being destroyed by oxidation. The enrichment factor of the proposed technique is 100, with variations possible. Recovery is 94% for tungsten and 99% for tin. Spectrophotometry of the thiocyanate complex and d.c. polarography are applied as determination techniques for tungsten and tin, respectively. Detection limits attainable by this technique are 6 ng · ml^–1 for tungsten and 5 ng · ml^–1 for tin for the initial sample.