Determination of trace amounts of vanadium(IV) and (V) in water by energy-dispersive x-ray fluorescence spectrometry combined with preconcentration and separation

A method is described for the separation, preconcentration and quantitation of V(IV) and V(V) in water. Vanadium(V) is precipitated with diethyldithiocarbamate (DDTC) at pH 1.8 and V(IV) is precipitated with DDTC at pH 4. The precipitates are collected by vacuum filtration on a membrane filter for quantitation by energy-dispersive x-ray fluorescence spectrometry. Multi-element and single-element calibration curves are prepared and used to evaluate the matrix and mass effects of diverse ions such as Fe(III), Co(II), Ni(II), Cu(II), Zn(II) and Pb(II). The total amount of metal ions should not exceed about 100 μg. The V(IV) and V(V) are separated completely and recovered quantitatively.     

Polymer-Enhanced Ultrafiltration of Fe(III) and Cu(II) Aqueous Solutions Using Poly(Vinyl Alcohol)-Alginic Acid/Cellulose Membranes

This study deals with the removal of Fe(III) and Cu(II) from dilute aqueous solutions using a polymer-enhanced ultrafiltration process. The ultrafiltration studies were carried out in batch stirred cell and the applied pressure was controlled by nitrogen gas. Properties of the composite membranes and its application in metal removal from aqueous solutions were studied. A composite poly(vinyl alcohol)-alginic acid/cellulose membranes were prepared by coating poly(vinyl alcohol)-alginic acid mixture solutions on the filter paper. Poly(vinyl alcohol) and alginic acid were also used as complexing agents to enhance the retention of metal ions. In the filtration of Fe(III) and Cu(II) solutions, the effects of membrane contents, pressure and pH on the retention and the flux were studied. The maximum retention of metals was found as 99% for Fe(III) solution at pressure of 45 psi, pH of 3 in the presence of poly(vinyl alcohol) as complexing agent by using 0.50 (w/v)% [(75 Poly(vinyl alcohol)/25 Alginic acid) (w/w)]/cellulose composite membranes.     

Copper(II)-selective fluorimetric bulk optode membrane based on a 1-hydroxy-9,10-anthraquinone derivative having two propenyl arms as a neutral fluorogenic ionophore

A new optical chemical sensor has been developed for the selective determination of copper(II) ions in aqueous solutions. The reversible sensing system was prepared by incorporating 1-hydrpxy-2-(prop-2'-enyl)-4-(prop-2'-enyloxy)-9,10-anthraquinone (AQ) as a neutral Cu2+-selective fluoroionophore in the plasticized PVC membrane with potassium tetrakis(p-chlorophenyl borate) as an anionic additive. The response of the sensor is based on the fluorescence quenching of AQ by Cu2+ ions. At a pH 5.5, the proposed sensor displays a calibration response for Cu2+ over a wide concentration rang of 1.0 x 10(-2) to 1.0 x 10(-6) M, with a relatively fast response of less than 40 s. In addition to high stability and reproducibility, the sensor shows a unique selectivity towards Cu2+ ion with respect to common co-existing cations. The proposed fluorescence optode was applied successfully to the determination of copper(II) in black tea samples.     

Adsorption behavior of metal ions onto a bovine serum albumin (BSA) membrane monitored by means of an electrode-separated piezoelectric quartz crystal.

The interaction between metal ions and bovine serum albumin (BSA) was studied by using a piezoelectric quartz crystal (PQC) arranged in the electrode-separated configuration. A silanized surface of the PQC was coated with a BSA membrane via a coupling reaction with glutaraldehyde. The frequency shifts obtained from PQC coated with a BSA membrane suggested that various kinds of metal ions could be adsorbed onto the BSA membrane from aqueous solutions containing a low concentration of metal ions (2 or 10 micromol dm(-3)), only when the BSA was denatured with an alkaline solution. Anionic species of Pt(IV) and Au(III) were adsorbed onto the denatured BSA membrane from an acetic acid solution at pH 2.2, and cationic species of Cd(II), Zn(II), Co(II), Ni(II), Cu(II), and Ag(I), and cations, such as Ca2+, Ba2+, and Mg2+, were adsorbed from ammonia buffer at pH 9.5, whereas Al(III), Cr(III), Fe(III), Hg(II), and Pb(II) were hardly adsorbed. The adsorption mechanisms of these metal ions are discussed, based on the electrostatic interaction between the metal ions and the denatured BSA membrane, and complex formation between the metal ions and amino acid residues of the denatured BSA. Further, the PQC coated with a denatured BSA membrane was applied to the determination of Pt and Cd, using large frequency shifts for Pt(IV) and Cd(II).     

Solid-phase extraction of some heavy metal ions on a double-walled carbon nanotube disk and determination by flame atomic absorption spectrometry

A new preconcentration method was developed for the determination of trace amounts of Cu(II), Fe(III), Pb(II), Ni(II), and Cd(II) on a double-walled carbon nanotube disk. 4-(2-Thiazolylazo) resorcinol was used as a complexing reagent. The effects of parameters, including pH of the solutions, amounts of complexing reagent, eluent type, sample volume, flow rates of solutions, and matrix ions were examined for quantitative recoveries of the studied analyte ions. The retained metal ions were eluted by 2 M HNO3. The LOD values for the analytes were in the range of 0.7-4.4 microg/mL. Natural water samples and standard reference materials were analyzed by the presented method.     

Collection of iron(III) from homogeneous aqueous solutions on membrane filters using Chromazurol B with Triton X-100.

A membrane filtration method was examined concerning the effective collection of iron(III) from a homogeneous aqueous solution with Chromazurol B (CAB), one of the triphenylmethane dyes, as a precipitating reagent in the presence of a non-ionic surfactant, polyethylene glycol mono[4-(1,1,3,3-tetramethylbutyl)phenyl]ether (Triton X-100). A formed blue Fe(III)-CAB complex was collected as a precipitate on a membrane filter by filtration under suction from a homogeneous aqueous solution in the pH range over about 2. The original solution was prepared at a concentration ratio of CAB to Fe(III) of to 10, and that of Triton X-100 to CAB of 10 to 100. It was then adjusted to a pH value of between 1.0 and 6.5. A linear relationship (r = 0.999) was obtained between the initial concentration and the found one of Fe(III) in the range of 2.0 x 10(-5) to 4.0 x 10(-4) mol dm(-3) at a fixed concentration ratio of CAB to Fe(III) of 3 and that of Triton X-100 to CAB of 20. This membrane filtration with CAB and Triton X-100 may be utilized for the separation of Fe(III) as a background species.     

Fluorimetric determination of copper(II) in aqueous solution using lucifer yellow CH as selective metal reagent

Lucifer yellow CH is shown to be a highly selective fluorescent reagent for the determination of Cu(III) in the microg L(-1) concentration range. The fluorophore is statically quenched by Cu(II); the carbohydrazide group was assigned as the complexing part of the dye molecule. A total range of Cu(II) determination from 0.06 mg L(-1) (1 micromol L(-1)) to 6.3 mg L(-2) (100 micromol L(-1)) with a limit of detection of 0.019 mg L(-1) (0.3 micromol L(-1)) was obtained, along with surprisingly high selectivity. There was no interference from alkaline and earth alkaline metal ions. The cross sensitivity to heavy metal ions was evaluated by the separate solution method and by competitive binding experiments. Calibration plots are shown for Cu(II) determination at different pH and the dissociation constant was determined. The application of the reagent was demonstrated by the determination of the Cu(II) content of tap water samples.     

Evaluation of coupled transport across a liquid membrane as an analytical preconcentration technique

When two aqueous solutions are separated by a liquid membrane that contains a complexing agent which is a conjugate base of a weak acid, a metal ion can be transported from the solution of the higher pH against its concentration gradient into the more acidic solution. With Cu(II) as the analyte and a liquid membrane consisting of a mixture of oximes dissolved in kerosene, enrichment factors for a prescribed dialysis time in a simple experimental apparatus were nearly independent of Cu(II) concentration over the range 10(-4)-10(-7)M. With 0.1M hydrochloric acid as the receiver, the enrichment factor was independent of ionic strength and of sample pH in the range 4-9. The effect of sample pH on the interference of Fe(III) was examined. With a pH-2.5 formate buffer, the enrichment factor for Cu(II) decreased as the Fe(III) concentration increased, but in a pH-9.3 ammonium buffer, 0.14 mM Fe(III) did not interfere with the transport of Cu(II) from a 16muM copper sample.     

Extractive-spectrophotometric determination of molybdenum with 4-unsubstituted-5-pyrazolones

A fairly sensitive and selective method for rapid determination of tracer amounts of molybdenum(V) as mixed-ligand complexes with thiocyanate and 4-unsubstituted-5-pyrazolones is described. The red complexes are extractable into chloroform from 1-5M hydrochloric or perchloric acid or 1-3M sulphuric arid media. The molar absorptivities are in the range 1.72-2.15 x 10(4)l.mole(-1).cm(-1) at 455 nm (lambda(max)). The method has been applied to the estimation of molybdenum in various synthetic and alloy-steel samples. In presence of excess of the reagent, Cu(II), Co(II), Mn(II), Fe(II), Fe(III), Al(III), Cr(III), Cr(VI), Ti(III), Ti(IV), Zr(IV), Hf(IV), V(III), V(IV), V(V), Nb(V), Ta(V), W(VI) and U(VI) do not interfere.     

Copper (II) adsorption from aqueous solution by herbaceous peat

In this research, the herbaceous peat collected from Gavurgolu peatlands, one of the biggest Turkish peatlands, was utilized as an adsorbent for the removal of copper (II) ions from aqueous solution. Adsorption experiments were conducted under various conditions, i.e., initial concentration, temperature, and pH. While the amount of Cu (II) adsorbed on the peat increased with increasing concentration of Cu (II) ions, it was not markedly affected by temperature and pH. Percentage removal was higher at lower concentration. For example, the maximum percentage removal of Cu (II) ions for initial concentration of 3 x 10(-4) M was 97.04% at 21 degrees C and pH 5.5. The adsorption capacity (Q(0)) of the peat was 4.84 mgg(-1) from Langmuir adsorption isotherm for the concentration range of 3 x 10(-4)-6 x 10(-4) M at 21 degrees C and pH 5.5. The equilibrium time of adsorption of Cu (II) ions was 150 min and independent of concentration and temperature. The amount of Cu (II) adsorbed at equilibrium time did not considerably change with temperature and pH. It was also determined that adsorption isotherm followed both Freundlich and Langmuir. Uptake mechanism of Cu (II) ions by the peat occurs via cation exchange (especially by means of Ca(2+) and Mg(2+)) as well as copper/peat complexation. Adsorption kinetic was consistent with the pseudo-second-order model.     

Determination of trace amounts of vanadium in air samples with 2-(8-quinolylazo)-5-N,N-diethylaminophenol by reversed-phase liquid chromatography

A reversed-phase liquid chromatographic method for the determination of trace amounts of vanadium is described. Metal ions are converted into 2-(8-quinolylazo)-5-N,N-diethylaminophenol chelates in an off-line system. The chelates are injected onto a Zorbax CN column and separated with an aqueous acetonitrile mobile phase containing no chromogenic reagent. Unter these conditions, only vanadium(V) is spectrophotometrically detected at 540 nm among the metal ions Al(III), Ba(II), Ca(II), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Ga(III), Hg(II), Mg(II), Mn(II), Ni(II), Pb(II), V(V) and Zn(II). Amounts of 8.0–200 pg of vanadium(V) in 100-μl injections can be determined without interference from 10-fold molar excesses of many cations. At 0.001 a.u.f.s., the detection limit (twice the peak-to-peak noise) for vanadium(V) is 8.0 pg in 100 μl of injected solution and the relative standard deviation at 120 pg of vanadium(V) in a 100-μl injection is 3.5%. The proposed method is applied to the determination of vanadium in rain water and airborne particulates.     

Ion‐imprinted poly(methyl methacrylate‐vinyl pyrrolidone)/poly(vinylidene fluoride) blending membranes for selective removal of ruthenium(III) from acidic water solutions

While conventional approaches have been studied for removal of ruthenium(III) ions (Ru(III)), this work focuses on the applicability of ion‐imprinted poly(methyl methacrylate‐vinyl pyrrolidone)/poly(vinylidene fluoride) blending membranes (Ru(III)–ion‐imprinted membrane[IIM]) for selective removal of Ru(III) from acidic water solutions. In order to measure the effectiveness of these imprinted membranes, after fabrication, binding experiments were done with aqueous Ru(III) solutions. The results showed that Ru(III)‐IIMs were fabricated successfully at various blending ratios, and their chemical components, microstructures, hydrophilicity, and water fluxes were measured. In pH range 0.5 to 5.0, binding capacity (Q_e) of Ru(III) onto Ru(III)‐IIM increases remarkably with pH and then reaches to a maximum value (53.52 mg/g) at pH 1.5. After that, Q_e gradually decreases. Compared with a nonimprinted membrane, Ru(III)‐IIM demonstrates higher selectivity for Ru(III) at pH 1.5 in the presence of Ni(II) and Cu(II) ions, and its selectivity coefficients for Ru(III)/Ni(II) and Ru(III)/Cu(II) are 3.70 and 3.32, respectively. Also, Ru(III)‐IIM shows a good chemical stability and reusability. C─N and C═O bonds within poly(vinyl pyrrolidone) segments of poly(methyl methacrylate‐vinyl pyrrolidone) (P(MMA‐VP)) participate the uptake of Ru(III). Ru(III)‐IIM exhibited excellent hydrophilicity and Ru(III) selective adsorption ability and reusability and has potential to be used for Ru(III) removal from acidic water solutions.     

Simultaneous determination of seven metal ions in water samples by solid-phase extraction on polyacrylonitrile activated carbon fibres

A new solid-phase extraction method utilising polyacrylonitrile activated carbon fibres (PAN-ACFs) as adsorbent was developed for the preconcentration of trace metal ions prior to their determination by inductively coupled plasma optical emission spectrometry (ICP-OES). The PAN-ACFs oxidised with nitric acid were characterised by FT-IR, XRD, SEM and BET analysis. Then the resulting PAN-ACFs were used as solid-phase adsorbent for simultaneously determination of trace Al(III), Be(II), Bi(III), Cr(III), Cu(II), Fe(III) and Pb(II) ions in aqueous solutions. The influences of the analytical parameters on the recoveries of the studied ions were investigated. The optimum experimental conditions of the proposed method were pH: 6.0; eluent concentration and volume: 3.0 mL of 1.5 mol L^?1 nitric acid; flow rates of sample and eluent solution: 1.5 mL min^?1. The preconcentration factors were found to be 67 for Al(III), Bi(III); 83 for Cr(III), Cu(II), Fe(III) and 50 for Be(II), Pb(II). The precision of this method was in range of 1.5%~3.5% and the detection limit of this metal ions was between 0.06~1.50 μg L^?1. The developed method was validated by the analysis of a certified reference sample and successfully applied to the determination of trace metal ions in water samples with satisfactory results.     

Spectrophotometric Study of Mithramycin Complexes with Cu(II), Fe(III) and Tb(III)

Abstract

The coordination of the anticancer drug mithramycin to Tb(III), Fe(III) and Cu(II) was studied in aqueous solution using absorption measurements. The stability constants were calculated from equilibrium competition experiments by means of the SQUAD program. For both first ions, the competitor was oxalic acid and for the latter the competitor was the Cu(II) ions. Cu(II) at pH 7.5, Fe(III) at pH 3.5 and Tb(III) at pH 5.5 formed respectively 1:2, 1:3 and 1:4 metal-to-ligand species.     

Micellar chromatographic separation of vanadium(V) chelate with 2-(2-thiazolylazo)-5-dimethylaminophenol

Summary In reversed phase—high performance liquid chromatography for metal chelates with 2-(2-thiazolylazo)-5-dimethylaminophenol, an aqueous non-ionic surfactant solution is used as a mobile phase. Among V(V), Fe(III), Cu(II), Co(II), Ni(II), Cd(II), Zn(II), Mn(II), and Al(III), only the V(V) chelate gave a resolved peak by using 0.8% w/w poly(oxyethylene)_n-4-nonylphenyl ether (n=20) solution buffered at pH 3.8. V(V) can be selectively separated and sensitively determined.     

Ion-Exchange Reaction of Silver(I) and Copper(II) in Optical Sensors Based on Thiaglutaric Diamide

Bulk optode membranes based on a recently reported thiaglutaric diamide ionophore were developed for measurements of silver(I) and copper(II) ions in aqueous solutions. The response properties of optical films containing ionophore and chromoionophores with different pK(a) values were investigated at different sample pH. At certain pH the measuring range of the optode can be shifted when choosing different chromoionophores. Optode with ionophore and chromoionophore V exhibited good responses to silver ions from 10(-6) - 10(-1) M at pH 5.5. The proposed sensor showed high selectivity, good reproducibility and stability. With a different chromoionophore ETH 5418 the optode could response to copper(II) ions from 10(-6) - 10(-2) M.     

The use of a polymer inclusion membrane in a paper-based sensor for the selective determination of Cu(II)

A disposable paper-based sensor (PBS) is described for the determination of Cu(II) in natural and waste waters at approximately 2 cents per measurement. The device makes use of a polymer inclusion membrane (PIM) to provide the selectivity for Cu(II). The PIM consists of 40 wt% di(2-ethlyhexyl) phosphoric acid (D2EHPA) as the carrier, 10 wt% dioctyl phthalate (DOP) as a plasticizer, 49.5 wt% poly(vinyl chloride) (PVC) as the base polymer and 0.5 wt% (m m⁻¹) 1-(2′-pyridylazo)-2-naphthol (PAN) as the colourimetric reagent. High selectivity under mildly acidic conditions (HCl, pH 2.0) is achieved for Cu(II) in the presence of frequently encountered metal ions in natural and waste waters such as Fe(III), Al(III), Zn(II), Cd(II), Pb(II), Ca(II), Mg(II), and Ni(II).     

Preparation, characterization and metal sorption studies of a Chrome-Azurol-S-loaded anion-exchange resin

Chrome Azurol S (CS) was mobilized on an strongly basic anion-exchange resin (Dowex 2 x 4, in Cl(-) form) by batch equilibration. The modified resin was stable in acetate buffer solution and in 0.1 M HCl and H(2)SO(4), but it was readily degraded with 2-6 M HCl and HNO(3). Retention of Ba(II), Sr(II), Ca(II), Mg(II), Al(III), Cr(III), Zn(II), Fe(III), Ti(IV), Mn(II), Co(II), Ni(II), Cu(II), Cd(II) and Pb(II) was studied using the batch equilibration method. The uptake and recovery yields were determined by using inductively-coupled plasma atomic emission spectroscopy (for Mg, Al, Cr, Ti, Fe, Mn, Ni, Zn, Cu, Cd and Pb) and atomic absorption spectrophotometry (for Ba, Sr, Ca and Co). The optimum pH value was established for performing a selective separation of Al(III) from the other metal ions. The sorption capacities of the CS-loaded resing for Al(III), Cr(III), Mg(II) (at pH 6), Fe(III) (at pH 5) and Ti(IV) (at pH 4) were 14, 2.9, 0.3, 3 and 3.9 mumoles g(-1) respectively. On this basis a method for separating Al(III) from other cations was established.     

Thiacalix[4]arenetetrasulfonate as specific pre-column chelating reagent for nickel(II) ion in kinetic differentiation mode high-performance liquid chromatography

Thiacalix[4]arenetetrasulfonate (TCAS) has been examined as a pre-column chelating reagent for the determination of trace metal ions by kinetic differentiation mode (KD) ion-pair reversed-phase high-performance liquid chromatography (HPLC) with spectrophotometric detection. Among 14 kinds of common metal ions tested here, viz. Al(III), Ca(II), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Hg(II), Mg(II), Mn(II), Ni(II), Pb(II), V(V), and Zn(II) ion, only Ni(II) ion was detected as the TCAS chelate in the HPLC separation stage in spite of TCAS forming the chelates with various metal ions except for Al(III), Ca(II), and Mg(II) at the pre-column chelation stage. The undetected metal-TCAS chelates seemed to be dissociated on an HPLC column where no added TCAS was present in the mobile phase because of their kinetic unstability. The calibration graph for Ni(II) ion gave a wide linear dynamic range (40-20,000 nM) with the very low detection limit (DL) (3σ base-line fluctuation) to be 5.4 nM (0.32 ng ml⁻¹). The practical applicability of the KD-HPLC method with TCAS was demonstrated with the determination of trace Ni in coal fly ash.     

Simultaneous spectrophotometric determination of binary mixtures of nickel,cobalt and vanadium with 3-(picolydene)benzenesulphonic acid 2-hydroxybenzoylhydrazone

The synthesis and characterization of a water-soluble reagent, 3-(picolydene)benzenesulphonic acid 2-hydroxybenzoylhydrazone, is described. The reagent is stable in aqueous media. The colour reations with nickel(II), cobalt(III) and vanadium(V) ions in slightly acidic solutions have molar absorptivities in the range 1.4–3.6 × 10⁴ l mol^?1 cm^?1. Simultaneous determinations of Ni, Co and V in binary mixtures are possible. Interference data are reported.