Development of a capillary electrophoresis method for the characterization of "palo azul" (Eysenhardtia polystachya)

The tree Eysenhardtia polystachya (Ortega) Sarg. has quite a wide popular use within the traditional Mexican medicine as herbal remedy. Popular practices constitute a relevant enough basis to design optimum analytical methods in order to determine basic principles of diverse medicinal plants. This has become one of the essentials needed to characterize such products, for which it is fundamentally important to develop an efficient and reliable separation method. This work presents the results concerning the development and optimization of a novel CE method for the separation of components from water/etanol (1:1) extracts of E. polystachya, using the following conditions, considered the best obtained: phosphate buffer 10 mM, 20 kV voltage, and pH 8.1 at 214 nm and 50 mM, 12.5 kV voltage with pH 8.1 at 426 nm. The optimization takes into account the parameters associated in the resulting electropherograms, such as number of peaks, migration times, and the Deltat(m) of the neighboring peaks. Under optimal conditions the separation intended was attained within 15 and 20 min for 214 and 426 nm, respectively. The characterization method developed was applied to the analysis of diverse extracts of E. polystachya.     

The analysis of human amniotic fluid using capillary electrophoresis

This study has investigated the composition of amniotic fluid (AF) using capillary electrophoresis (CE). A detailed optimisation investigation was undertaken to obtain the best resolution of the major peaks in amniotic fluid. In the final method, capillary zone electrophoresis (CZE) of AF was performed on a Hewlett Packard3D CE instrument using a fused-silica capillary of 44 cm total length (36 cm to the detector) with in internal diameter of 50 microm. The background electrolyte was 20 mM sodium tetraborate containing 0.8 mM EDTA adjusted to pH 9.0. AF was diluted 1 plus 1 with deionised water prior to hydrodynamic injection for 3 s at 50 mbar. The separation was performed at +22.5 kV and resulted in a current of 65 microA. The capillary temperature was 28 degrees C. Using this CZE method, some eight peaks were consistently resolved in AF samples and several other more transient peaks have been separated from AF in less than 10 min. A scheme for the identification of peaks once they had been separated was also developed. Four peaks have been identified as proteins, i.e., gamma-globulin, alpha1-antitrypsin, transferrin and albumin. Surprisingly, one major peak was shown to be the purine catabolite, xanthine.     

Direct comparison of capillary electrophoresis and capillary liquid chromatography hyphenated to collision-cell inductively coupled plasma mass spectrometry for the investigation of Cd-, Cu- and Zn-containing metalloproteins

Capillary liquid chromatography (cLC) and capillary electrophoresis (CE) have been critically compared for the separation of metalloproteins when using collision-cell inductively coupled plasma mass spectrometry (ICP-CC-MS) as detection system. For cLC separation, the selected column was a C8 (0.3 mm I.D.) and the separation conditions involved a gradient up to 80% methanol in 10mM ammonium acetate buffer (pH 7.4). The low flow rate used (3 microL min(-1)) permitted the utilization of a high methanol content maintaining the sensitivity along the whole chromatographic run. For this purpose, a new low-flow interface has been developed based on a total consumption nebulizer. Similarly, CE has been studied as separation technique using a 75 microm I.D. fused silica capillary and a running buffer of 20 mM Tris-HNO3 (pH 7.4) and working at 30 kV. Metallothionein (mixture of MT-I and -II) and superoxide dismutase (SOD) have been used as protein models in order to evaluate the separation/detection capabilities using the same injection volumes in both systems (20 nL). For both hybrid systems, separation parameters such as retention factor, numbers of theoretical plates, tailing factor and resolution have been critically compared. Also, the analytical performance characteristics of both hybrid systems have been evaluated and tested by analyzing the Cu-, Zn-species present in red blood cell extracts in order to explore more adequate separation methodology for the analysis of metalloproteins in complex matrices.     

Separation and identification of the organic acids in Angelicae Radix and Ligustici Rhizoma by HPLC and CE

Angelicae Radix (AR) and Ligustici Rhizoma (LR) are both derived from the Umbelliferae plants and contain similar organic acids as their bioactive compounds. Nine of these organic acids, including nicotinic acid, protocatechuic acid, phthalic acid, folinic acid, p-hydroxybenzoic acid, folic acid, vanillic acid, caffeic acid, and ferulic acid were separated by HPLC and CE. Detection at 210 nm with a linear gradient containing 20 mM KH2PO4 (pH 3.5) and H2O-CH3CN in HPLC and with a buffer solution containing 10 mM LTAC, 2 mM Na2HPO4, 9 mM Na2B4O7(pH 9.56), and CH3CN in CE were found to be the most efficient eluents for this separation. The contents of the nine components in crude extracts of either AR or LR could easily be determined within 60 min by LC and within 20 min by CE. The structures of the individual peaks in the LC chromatogram were identified by LC-MS. The effects of buffers on the separation and validation of the two methods were examined.     

Analysis of Salvia officinalis plant extracts by capillary electrophoresis

Salvia officinalis (commonly called Sage) and similar plants contain many compounds of pharmaceutical interest and are used as a tea or in various pharmaceutical products. In this work, the use of CE for analysis of aqueous or ethanolic extracts from various Salvia plants has been studied. Especially, several buffers like borate, phosphate, acetate, etc., were examined under different concentrations, pH, separation voltage, injection time, and other parameters to find the optimal separation conditions. The optimization was also performed using experimental design and artificial neural networks. The optimal conditions were: separation voltage +20 kV, 40 mM buffer borate, pH 9.2, injection time 5 s, and UV detection at 280 nm. A new CE method has been developed, validated, and applied to analyze samples of S. officinalis from various countries.     

CE–MS for anionic metabolic profiling: An overview of methodological developments

The efficient profiling of highly polar and charged metabolites in biological samples remains a huge analytical challenge in metabolomics. Over the last decade, new analytical techniques have been developed for the selective and sensitive analysis of polar ionogenic compounds in various matrices. Still, the analysis of such compounds, notably for acidic ionogenic metabolites, remains a challenging endeavor, even more when the available sample size becomes an issue for the total analytical workflow. In this paper, we give an overview of the possibilities of capillary electrophoresis‐mass spectrometry (CE–MS) for anionic metabolic profiling by focusing on main methodological developments. Attention is paid to the development of improved separation conditions and new interfacing designs in CE–MS for anionic metabolic profiling. A complete overview of all CE–MS‐based methods developed for this purpose is provided in table format (Table 1) which includes information on sample type, separation conditions, mass analyzer and limits of detection (LODs). Selected applications are discussed to show the utility of CE–MS for anionic metabolic profiling, especially for small‐volume biological samples. On the basis of the examination of the reported literature in this specific field, we conclude that there is still room for the design of a highly sensitive and reliable CE–MS method for anionic metabolic profiling. A rigorous validation and the availability of standard operating procedures would be highly favorable in order to make CE–MS an alternative, viable analytical technique for metabolomics.     

Analysis of silica nanoparticles by capillary electrophoresis coupled to an evaporative light scattering detector

A simple and rapid methodology has been developed to identify and separate silica nanoparticles (SiO₂NPs) of different sizes in aqueous solution by capillary zone electrophoresis coupled to an evaporative light scattering detector (CE-ELSD). SiO₂NPs were separated using 3 mM ammonium acetate buffer, containing 1% methanol at pH 6.9. SiO₂NPs of 20, 50 and 100 nm were successfully separated under the optimum experimental conditions. CE coupled to ELSD has been proven to be an effective separation technique to determine particles with such small sizes, although the peaks are very close to each other, and it is a promising technique that may allow the separation of other types of nanoparticles. Confirmation by TEM and quantification of the SiO₂ content was also carried out by inductively coupled plasma-mass spectrometry (ICP-MS). The new method was applied to the analysis of real samples, in order to assess its ability to avoid matrix effects in the determination of SiO₂NPs in these kinds of samples.     

毛细管电泳分析中手性化合物的定性检测

毛细管电泳（CE）作为一种新型分离分析技术,具有分离效率高、分析速度快、样品用量少、分离模式灵活多样等众多优势,在手性物质分离等领域应用广泛。在以往的工作中,手性化合物的CE分离模式、手性拆分剂选择及提高分离度等研究已作了详尽报道,而成功分离后的手性物质定性、对映体出峰顺序确认等问题也至关重要。该文以CE手性化合物分离分析中是否依赖标准品分类,及其定性检测方法进行了总结。     

Fast enantioseparation of arylglycine amides by capillary electrophoresis with highly sulfated-beta-cyclodextrin as a chiral selector

Nine racemic arylglycine amides were synthesized and successfully enantioseparated by capillary electrophoresis (CE) using highly sulfated beta-cyclodextrin (HS-beta-CD) as a chiral selector. Baseline enantioseparation of the analytes was obtained around neutral pH but not in the acidic conditions that are commonly used. HS-beta-CD content, buffer pH, type and concentration, and organic modifier concentration were studied and optimized for fast and efficient separation. A chiral CE separation system composed of 1.5% (w/v) HS-beta-CD, 0 to 10% (v/v) methanol and 20 mM 3-(N-morpholino)propanesulfonic acid at pH 6.5 was shown suitable for baseline enantioseparation of the mentioned amides within 6 min, including simultaneous enantioseparation of three positional isomer series (methyl-, methoxyl or chloro-substituted). By using this system, D-enantiomers migrated ahead of the L-enantiomers and the enantiomeric resolution order of arylglycine amides was more or less parallel to the pK(a), order of the analytes.     

Sensitivity enhancement for the analysis of naproxen in tap water by solid-phase extraction coupled in-line to capillary electrophoresis

SPE coupled in-line to CE, as the strategy to enhance the concentration sensitivity in CE, has been used to enrich naproxen in tap water samples. In this study, a microcartridge containing an octadecyl silica (C18) sorbent was placed near the inlet within the separation capillary column. The optimum conditions were obtained when naproxen in an acidic aqueous solution (pH 3.5) was loaded into the capillary at 930 mbar for 30 min, and 20 mM ammonium acetate in methanol/water (70:30 v/v) was used as both an elution solution and a separation BGE. Under these conditions, the sensitivity was enhanced 1820-fold with respect to normal hydrodynamic injection, and the LOD achieved was 0.2 microg/L. To show the capability of the in-line SPE-CE method, tap water samples were analysed after a pretreatment consisting in an off-line C18-SPE procedure. The recovery of this procedure was higher than 80%. Under these conditions, naproxen could be detected at a concentration of 10 ng/L; so the potential of the procedure for the sensitive analysis of this type of drugs in water samples was demonstrated. Afterwards, these results were compared with those previously obtained for naproxen in water samples using different sample stacking techniques.     

Analysis of neutral nitromusks in incenses by capillary electrophoresis in organic solvents and gas chromatography-mass spectrometry

Nitromusks used as fragrances in a variety of personal-care products, cleansers, and domestic deodorants, including incense sticks, are neutral nitro aromatic compounds; some of these have been reported as photosensitizers. In this work, their analysis was performed by capillary electrophoresis (CE) in a methanol-based background electrolyte (BGE). In particular, a 10 mM solution of citric acid in methanol was used; under these conditions the strong suppression of the electroosmotic flow favored the use of negatively charged surfactants as additives for the anodic migration of the studied analytes. To this end, sodium taurodeoxycholate (TDC) was supplemented at high concentration (190 mM) to the organic background electrolyte (BGE), showing strong indication of the ability to give micelle-like aggregates. Since nitromusks are characterized by the presence of a nitroaromatic ring with low charge density, their association with TDC aggregates can be ascribed to donor-acceptor interactions. Separation of musk xylene, musk ketone, and the banned musk moskene and musk ambrette was obtained under full nonaqueous BGE; the addition of relatively small water percentages (15% v/v) was found to be useful in improving the separation of pairs of adjacent peaks. Under optimized conditions (190 mM sodium TDC in methanol-water, 85-15 v/v containing citric acid 10 mM) the system was applied to the analysis of nitromusks in incense sticks extracted with methanol. The results were compared with those obtained by the analysis of the same samples using gas chromatography with mass detector. The expected different selectivity of separation obtained using the two techniques can be useful in the unambiguous determination of the analytes; furthermore, a substantial accord of the preliminary quantitative results achieved with the two methods was assumed as the confirmation of the potential reliability of CE performed with high percentage of organic solvent.     

Separation and determination of metal cations in milk and dairy products by CE

To prevent casein adsorption and improve between-run repeatability, a CE procedure is developed for cation analysis in milk using a modified imidazole/alpha-hydroxyisobutyric acid (HIBA) BGE system to operate at pH 6 to match the pH of milk and elevate imidazole concentration to enhance its buffer action. The procedure is shown to produce a fast, economic and efficient method for cation separation in milk with only simple dilution. Upon direct hydrodynamic injection of diluted milk sample at 8 cm for 30 s in an uncoated column with a BGE consisting of 10 mM imidazole, 10 mM HIBA and 10% methanol at pH 6.0 under +18 kV, baseline separation was achieved for K(+), Na(+), Ca(2+), Mg(2+), Mn(2+), Cd(2+), Co(2+), Ni(2+)and Zn(2+). Agreeable results at 95% confidence level were obtained using CE and inductively coupled plasma-atomic emission spectrometry (ICP-AES) for milk samples after protein removal. Baseline-resolved peaks for essential minerals were obtained for fresh and non-refrigerated reconstituted milks. Long-term stability was demonstrated by repeated determinations without rinsing and improvement in repeatability was shown by rinsing with 60 mM SDS in BGE. Information on metal speciation useful for nutritional assessment was obtained from CE to complement the ICP methods.     

Analysis of serotonin in brain microdialysates using capillary electrophoresis and native laser-induced fluorescence detection

Serotonin or 5-hydroxytryptamine (5-HT) is a major neurotransmitter in the central nervous system. In this work, a method for analyzing 5-HT in brain microdialysis samples using a commercially available capillary electrophoresis (CE) system has been developed. A pH-mediated in-capillary preconcentration of samples was performed, and after separation by capillary zone electrophoresis, native fluorescence of 5-HT was detected by a 266 nm solid-state laser. The separation conditions for the analysis of 5-HT in standard solutions and microdialysates have been optimized, and this method has been validated on both pharmacological and analytical bases. Separation of 5-HT was performed using a 80 mmol/L citrate buffer, pH 2.5, containing 20 mmol/L hydroxypropyl-beta-cyclodextrin (HP-beta-CD) and +30 kV voltage. The detection limit was 2.5 x 10(-10) mol/L. This method allows the in vivo brain monitoring of 5-HT using a simple, accurate CE measurement in underivatized microdialysis samples.     

Quality evaluation of Guan‐Xin‐Ning injection based on fingerprint analysis and simultaneous separation and determination of seven bioactive constituents by capillary electrophoresis

The purpose of this study was to develop a comprehensive, rapid and practical capillary electrophoresis (CE) method for quality control (QC) of Guan‐Xin‐Ning (GXN) injection based on fingerprint analysis and simultaneous separation and determination of seven constituents. In fingerprint analysis, a capillary zone electrophoresis (CZE) method with a running buffer of 30 mM borate solution (pH 9.3) was established. Meanwhile, ten batches of samples were used to establish the fingerprint electropherogram and 34 common peaks were obtained within 20 min. The RSD of relative migration times (RMT) and relative peak areas (RPA) were less than 5%. In order to further evaluate the quality of GXN injection, a micellar electrokinetic chromatography (MEKC) method was developed for simultaneous separation and determination of bioactive constituents. Seven components reached baseline separation with a running buffer containing 35 mM SDS and 45 mM borate solution (pH 9.3). A good linearity was obtained with correlation coefficients from 0.9906 to 0.9997. The LOD and LOQ ranged from 0.12 to 1.50 μg/mL and from 0.40 to 4.90 μg/mL, respectively. The recoveries ranged between 99.0 and 104.4%. Therefore, it was concluded that the proposed method can be used for full‐scale quality analysis of GXN injection.     

Niacin Determination in Legumes by Capillary Electrophoresis (CE). Comparison with High Performance Liquid Chromatography (HPLC)

Available and total niacin content in lentils and faba beans have been analyzed by capillary electrophoresis (CE), and the results compared with those obtained by high performance liquid chromatography (HPLC). Acidic and enzymatic hydrolysis have been carried out for available niacin determination, and an alkaline extraction performed for total niacin. The extracts were subsequently purified using a strong anion exchanger resin. Precise conditions for purification had to be worked out for each one of the two analytical methods (HPLC and CE). The HPLC analysis for available and total niacin was carried out in an ion-pair reverse phase column with UV detection at 261 nm. For the CE separation, the following conditions were employed: a 20 mM sodium tetraborate; 15 mM sodium dodecyl sulfate and 20% isopropyl alcohol solution as separation buffer; 30 kV and 25 or 30°C. Separation was carried out in a 70 cm effective length × 75 μm i.d. fused-silica capillary using on-column UV detection at 254 nm. The results obtained by CE for lentils and faba beans were similar to those obtained by HPLC.     

Separation of nucleoside mono-, di- and triphosphates by capillary electrophoresis via cadmium complexation

Summary The CE separation of twelve nucleotides (5′-mono-, di-, triphosphates of adenosine, guanosine, cytidine and uridine) was improved by adding cadmium ion to the ammonium citrate/citric acid buffer (pH 5, ionic strength 100 mM). Cadmium ion acts as a complexing agent for some nucleotides (ATP, CTP, GTP, UTP, GDP). In order to accelerate the separation, the electroosmotic flow was reversed by flushing the fused-silica capillary with 0.2 % aqueous solution of the polycationic surfactant hexadimethrine bromide. A good separation of the twelve nucleotides studied was then achieved on a dynamically coated capillary in less than 5 min by using an ammonium citrate/citric acid buffer (pH 5, ionic strength 100 mM) to which 2 mM cadmium ion has been added. High peak efficiencies were obtained (210 000 theoretical plates) and the resolution between two adjacent peaks was always greater than 1.5.     

Synthesis and application of dehydroabietylisothiocyante as a new chiral derivatizing agent for the enantiomeric separation of chiral compounds by capillary electrophoretic

A new chiral derivatizing reagent, dehydroabietylisothiocyante (DHAIC), was synthesized and used for the enantiomeric separation of chiral compounds in capillary electrophoresis (CE). The synthetic route to obtain DHAIC is described. The separation conditions for the chiral separation of several chiral compounds, such as protein amino acids and chiral drug DOPA were optimized. Best results for the chiral separation of DHAIC derivatized amino acids and DOPA were obtained in a running buffer consisted of 50 mM borate (pH 9.5), 5 mM sodium dodecyl sulphate (SDS) and 20% acetonitrile for amino acids and 60 mM Na₂HPO₄ (pH 8.0), 17 mM SDS and 25% acetonitrile for DOPA. Under the conditions studied, chiral separation of five amino acids including Ser, Val, Ala, Thr, Cys and a chiral drug DOPA as their diastereomeric DHAIC derivatives has been achieved by micellar electrokinetic chromatography (MEKC).     

Different strategies for the preconcentration and separation of parabens by capillary electrophoresis

Several strategies, namely, large volume sample stacking (LVSS), field‐amplified sample injection (FASI), sweeping, and in‐line SPE‐CE, were investigated for the simultaneous separation and preconcentration of a group of parabens. A BGE consisting of 20 mM sodium dihydrogenphosphate (pH 2.28) and 150 mM SDS with 15% ACN was used for the separation and preconcentration of the compounds by sweeping, and a BGE consisting of 30 mM sodium borate (pH 9.5) was used for the separation and preconcentration of the compounds by LVSS, FASI, and in‐line SPE‐CE. Several factors affecting the preconcentration process were investigated in order to obtain the maximum enhancement of sensitivity. The LODs obtained for parabens were in the range of 18–27, 3–4, 2, and 0.01–0.02 ng/mL, and the sensitivity evaluated in terms of LODs was improved up to 29‐, 77‐, 120‐, and 18 400‐fold for sweeping, LVSS, FASI, and in‐line SPE‐CE, respectively. These preconcentration techniques showed potential as good strategies for focusing parabens. The four methods were validated with standard samples to show the potential of these techniques for future applications in real samples, such as biological and environmental samples.     

Optimization of the separation conditions of tetracyclines on a preselected reversed-phase column with embedded urea group

The use of a C12 stationary phase with embedded polar group has been investigated for the separation of seven tetracyclines. The influence of pH, organic modifier, buffer, and temperature on the peak shape and analyte separation was discussed. It appears that all the chromatographic conditions had a great effect on both the resolution and peak shape whereas the elution order was not affected. The baseline separation with symmetrical peaks of the seven tetracyclines can be obtained with a mobile phase containing either 5 mM phosphate buffer pH 2.5/ACN (84:16 v/v) or 5 mM perchlorate buffer pH 2.5/ACN (75:25 v/v) at a temperature not exceeding 20 degrees C. This study reveals that the retention mechanism is ion-pairing.     

Determination of hydrolyzable tannins in the fruit of Terminalia chebula Retz. by high-performance liquid chromatography and capillary electrophoresis

A RP-HPLC method for determining fourteen components (gallic acid, chebulic acid, 1,6-di-O-galloyl-D-glucose, punicalagin, 3,4,6-tri-O-galloyl-D-glucose, casuarinin, chebulanin, corilagin, neochebulinic acid, terchebulin, ellagic acid, chebulagic acid, chebulinic acid, and 1,2,3,4,6-penta-O-galloyl-D-glucose) in the fruit of Terminalia chebula Retz. is described. The separation was achieved within 80 min using a binary gradient with mobile phases consisting of a pH 2.7 phosphoric acid solution and an 80% CH3CN solution. Capillary electrophoretic analyses were also attempted, and it was found that CZE (25 mM Na2B4O7, 5 mM NaH2PO4, pH 7.0) was an efficient method for the separation of gallotannins, while an MEKC method (25 mM Na2B4O7, 5 mM NaH2PO4, 20 mM SDS, pH 7.0, and 10% acetonitrile) provided a better separation for most of the tannins examined. The HPLC and CE methods developed were both successfully applied to the assay of tannins in commercial samples of Chebulae Fructus.