Modification of mechanical and thermal property of chitosan–starch blend films

Chitosan–starch blend films (thickness 0.2 mm) of different composition were prepared by casting and their mechanical properties were studied. To improve the properties of chitosan–starch films, glycerol and mustard oil of different composition were used. Chitosan–starch films, incorporated with glycerol and mustard oil, were further modified with monomer 2-hydroxyethyl methacrylate (HEMA) using gamma radiation. The modified films showed improvement in both tensile strength and elongation at break than the pure chitosan–starch films. Water uptake of the films reduced significantly than the pure chitosan–starch film. Thermo gravimetric analysis (TGA) and dynamic mechanical analysis (DMA) showed that the modified films experience less thermal degradation than the pure films. Scanning electron microscopy (SEM) and FTIR were used to investigate the morphology and molecular interaction of the blend film, respectively.     

Preparation of gelatin/poly(vinyl alcohol) film modified by methyl methacrylate and gamma irradiation

The properties of gelatin–polyvinyl alcohol (G–PVA) blend films were improved by methyl methacrylate (MMA) and γ irradiation for a practical viewpoint. The films were prepared by the casting method, modified by glycerol and MMA monomer, and their mechanical properties were also studied. The gelatin-based films were successfully prepared using γ irradiation (3.1 kGy) and gelatin: PVA = 97:3 (w/w) as optimized. Tensile properties of the films were studied and thermal properties of the films were characterized by thermogravimetric analysis and dynamic mechanical analysis pointed out that MMA treated both gelatin films, and G–PVA blend films showed less thermal degradation than untreated films. In addition, structural and morphological features of the gelatin-based films were examined by Fourier transform infrared and scanning electron microscopy, respectively. The ultimate results of the present study showed remarkable enhancement in tensile properties (> 40%) and a reduction in elongation at break of the films, thanks to the MMA addition and γ irradiation.     

Study on grafting of different types of acrylic monomers onto natural rubber by γ-rays

 A comparative study of various acrylic monomers for grafting onto natural rubber was done. The stability of natural rubber latex (NRL) against coagulum with monomer, mechanical properties of grafted rubbers and percent of grafting were investigated. The NRL with monomers, methylacrylate (MA), ethylacrylate (EA) and n-butylacrylate (n-BA), is unstable but it is stable with methyl methacrylate (MMA), n-butyl methacrylate (BMA) and cyclohexyl methacrylate (CHMA). The mechanical properties and degree of grafting attained a maximum at a total radiation dose of 4 kGy. The values of tensile properties of MMA and CHMA grafted rubbers are almost similar, and higher than those of BMA grafted rubbers. On the other hand, the degree of grafting for CHMA is higher than those of MMA and BMA grafted rubbers. The infrared (IR) spectra of monomer grafted natural rubber were also studied.     

Studies on the properties and characteristics of starch-LDPE blend films using cross-linked, glycerol modified, cross-linked and glycerol modified starch

Corn starch was modified by cross-linking with epichlorohydrin and plasticizer glycerol. X-ray diffraction studies showed that relative crystallinity of the native and cross-linked starch were similar and were not affected by cross-linking. Different films were prepared by blending corn starch, cross-linked starch or glycerol modified starch in LDPE. The mechanical properties of the films were studied for tensile strength, elongation, melt flow index, and burst strength. The properties of the blend films were compared with LDPE films. It was observed that with the blending of 7.5% native starch, there was a decrease in tensile strength, elongation and melt flow index but burst strength increased. The tensile strength, elongation and melt flow index of the films containing cross-linked starch was considerably higher than those containing native starch but the burst strength showed a reverse trend. For native starch and cross-linked starch modified with glycerol, the elongation and melt flow index of the films increased but burst strength decreased. Surface scanning of the blend films were done by scanning electron microscope. Film containing cross-linked starch/glycerol modified starch in the blend was observed to be smoother than the native starch blend films.     

Mechanical and thermal properties of irradiated films based on Tilapia (Oreochromis niloticus) proteins

Proteins are considered potential material in natural films as alternative to traditional packaging. When gamma radiation is applied to protein film forming solution it resulted in an improvement in mechanical properties of whey protein films. The objective of this work was the characterization of mechanical and thermal properties of irradiated films based on muscle proteins from Nile Tilapia (Oreochromis niloticus). The films were prepared according to a casting technique with two levels of plasticizer: 25% and 45% glycerol and irradiated in electron accelerator type Radiation Dynamics, 0.550 MeV at dose range from 0 to 200 kGy. Thermal properties and mechanical properties were determined using a differential scanning calorimeter and a texture analyzer, respectively. Radiation from electron beam caused a slightly increase on its tensile strength characteristic at 100 kGy, while elongation value at this dose had no reduction.     

Gamma-Irradiated Gelatin-Based Films Modified by HEMA for Medical Application

The present article describes the synthesis and characterization of bi-component polymer systems based on gelatin films incorporated with 2-hydroxyethyl methacrylate (HEMA) monomer, developed for medical application. Gelatin films were prepared by the addition of HEMA of different concentrations (0–30 wt.%) and irradiated with various radiation doses (0–5 kGy). Tensile strength and tear strength of the irradiated gelatin films were found to increase with increasing HEMA up to 20 wt.% as well as radiation doses (1 kGy) as optimized. The maximum tensile and tear strengths of irradiated gelatin films with HEMA were found to be 79.1 MPa and 83.2 N/mm, respectively, at the optimum conditions, and these values were about double that of a reference film prepared without additives. In addition, morphological analysis was done by scanning electron microscopy (SEM) and showed how HEMA cemented and was covered with gelatin in the blend. Thermomechanical analysis was carried out to investigate the shifting of glass transition temperature (T_g) towards higher temperature due to HEMA addition, and the effect of this film was tested on the human body in order to determine whether it can be applied for medical purposes.     

Preparation and characterization of polypropylene and waste tire powder modified by allylamine blends

Waste tire powder subjected to allylamine modification in the presence of ultraviolet (UV) radiation has been used to prepare polypropylene based thermoplastic vulcanizates with maleic anhydride polypropylene (MA‐PP) as compatibilizer. The effect of increasing the concentration of MA‐PP on performance characteristics like tensile strength, elongation and rheological properties have been investigated. X‐ray diffraction studies of the PP/waste tire powder blend indicate the disappearance of β crystalline peaks on addition of waste tire powder in the PP, whereas it is observed in the allylamine modified rubber powder loaded PP. Differential scanning calorimetry results further supported the above fact. The improvement in mechanical properties of the PP/allylamine modified rubber powder loaded thermoplastic vulcanizates has been explained in terms of βα transformation of PP crystals during straining of the samples and uniform dispersion of allylamine coated rubber powder in the PP matrix. The melt rheological properties of the thermoplastic vulcanizates loaded with modified rubber powder are higher than its counterpart due to the higher dispersion as a result of chemical interaction between the rubber powder surface with the MA‐PP. Copyright © 2008 John Wiley & Sons, Ltd.     

Copolymerization and Properties of Multicomponent Crosslinked Hydrogels

A series of multicomponent hydrogels were prepared by the copolymerization of hydrophobic silicon-containing monomer 3-bis(trimethylsilyloxy) methylsilylpropyl glycerol methacrylate(Si MA) with the solvent-responsive monomers 2-hydroxyethyl methacrylate(HEMA) and N-vinyl pyrrolidone(NVP) and thermosensitive monomer N,N-dimethyl acrylamide(DMA). 2-Hydroxy-2-methyl phenyl acetone(D-1173) was chosen as UV initiator and five different dienes/triene monomers were selected as crosslinking agent in order to select the best crosslinker. The ethanol extraction experiments as well as the FTIR, DSC and TG results showed that the copolymerization was effective. The optical, permeability, and mechanical analysis results demonstrated that the obtained hydrogels were highly transparent with good oxygen permeability and mechanical properties. And the impact of crosslinker on the mechanical properties of the hydrogels was also discussed in detail. The basic results demonstrated that the obtained hydrogels had good stimuli-responsive effects to both p H value and solvent.     

Graft co-polymerization of casein with acrylonitrile and n-butyl methacrylate

Casein was grafted using acrylonitrile and n-butyl methacrylate. The mechanical properties of the grafted co-polymer films were studied using an Instron Universal Testing Machine. The morphological characteristics were studied by scanning electron microscopy. The tensile strength was found to increase and elongation at break to decrease with increasing monomer content. The compatibility of the graft co-polymer and homopolymer formed was found to be important in governing the morphological features of the films.     

Improving the Processing Ability and Mechanical Strength of Starch/Poly(vinyl alcohol) Blends through Plasma and Acid Modification

Summary: In this study, maleic anhydride (MA), and citric acid (CA) used as the processing additive and plasma treatment to improve the processing ability and mechanical strength of biodegradable starch/poly (vinyl alcohol) (PVA) blends were studied. The melt flow index (MFI) of starch/ glycerol/PVA (300g/60g/80g) blend was increased from 2.3g/10min to 32.7g/10min by adding 3g of MA and to 130 g/10min by adding MA and plasma treatment. The tensile strength of starch/glycerol/PVA blend increased from 3.48 to 6.21 MPa by adding 1.5g of MA and 1.5g of CA, while it increased to 6.26 MPa by plasma treatment. Esterification reaction which was evidenced by FTIR has been showed to improve the compatibility between starch and PVA when MA was dissolved into glycerol and glycerol grafted onto plasma pretreatment PVA. Thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) imaging were used to study the morphology of extruded blends.     

Cornstarch/Poly(vinyl alcohol) Biocomposite Blend Films: Mechanical Properties,Thermal Behavior,Fire Retardancy,and Antibacterial Activity

In the present study, biocomposite films of starch/poly(vinyl alcohol) (St/PVA) reinforced with delignified Grewia optiva fiber and methyl methacrylate (MMA) grafted fibers were prepared using citric acid as a plasticizer and glutaraldehyde as the cross-linker. The biocomposite films were subjected to evaluation of mechanical properties, biodegradability, and antibacterial properties. The biocomposite films were characterized by using Fourier transform-infrared (FT-IR) spectrophotometry, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA/DTA/DTG). SEM showed good adhesion between St/PVA blend matrix and fibers. The antimicrobial activity of biocomposite films against pathogenic bacteria such as Staphylococcus aureus and Escherichia coli was also explored. The results confirmed that the biocomposite films may be used for food packaging.     

Modification of hydrophilic poly(vinyl alcohol) film via blending with hydrophobic poly(butyl acrylate-co-methyl methacrylate)

A series of poly(vinyl alcohol)/poly(butyl acrylate-co-methyl methacrylate) [PVA/P(BA-co-MMA)] blend films with different P(BA-co-MMA) content were prepared by the solution casting method. Surface morphologies of the PVA/P(BA-co-MMA) blend films were studied by scanning electron microscopy and atomic force microscopy. Thermal, mechanical, and chemical properties of PVA/P(BA-co-MMA) blend films were investigated by differential scanning calorimeter, thermogravimetric analysis, tensile tests, and surface contact angle tests. It was revealed that the introduction of P(BA-co-MMA) could affect the properties of the PVA films. The results also showed that, when P(BA-co-MMA) mole content is 3 %, the tensile strength and the surface contact angle of the polymer blend film are 20.4 MPa and 43.5°, respectively, suggesting that the polymer blend film holds both a better mechanical property and a better chemical property.     

Biodegradable stereocomplex materials of polylactide‐grafted dextran exhibiting soft and tough properties in dry and wet states

Water‐swellable biodegradable materials exhibiting mechanically tenacious and tough characters in the wet state were prepared by a simple blend of two enantiomeric polylactide‐grafted dextran copolymers (Dex‐g‐PLLA and Dex‐g‐PDLA). DSC and WAXD analyses demonstrated the formation of SC crystals in the copolymer blend films. SC blend films showed lamellar‐type microphase‐separated structures. When swollen with water, these blend films showed the same level of tensile strengths and Young's modulus as the films in the dry state. SC blend films degraded gradually over a month under physiological conditions with a degradation rate faster than the corresponding Dex‐g‐PLLA films. The SC‐forming enantiomeric mixture of polylactide‐grafted polysaccharides should be a good candidate for an implantable biocompatible material exhibiting favorable mechanical properties and degradation behavior. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermal behaviors and characteristics of polylactide/poly(butylene succinate) blend films via reactive compatibilization and plasticization

Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of T_cc and T_m, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.     

Poly(lactic acid)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer/sepiolite nanocomposites: Investigation of thermo‐mechanical and morphological properties

In this study, sepiolite nanoclay is used as reinforcing agent for poly(lactic acid) (PLA)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer (SEBS‐g‐MA) 90/10 (w/w) blend. Effects of sepiolite on thermal behavior, morphology, and thermomechanical properties of PLA/SEBS‐g‐MA blend were investigated. Differential scanning calorimetry results showed 7% improvement in crystallinity at 0.5 wt% of sepiolite. The nanocomposite exhibited approximately 36% increase in the tensile modulus and 17% increase in toughness as compared with the blend matrix at 0.5 and 2.5 wt% of sepiolite respectively. Field emission scanning electron microscopy and transmission electron microscopy images exhibited sepiolite‐induced morphological changes and dispersion of sepiolite in both PLA and SEBS‐g‐MA phases. Dynamic mechanical analysis and wide angle X‐ray diffraction present evidences in support of the reinforcing nature of sepiolite and phase interaction between the filler and the matrix. This study confirms that sepiolite can improve tensile modulus and toughness of PLA/SEBS‐g‐MA blend.     

Reactive compatibilization of nylon copolymer/EPDM blends: experimental aspects and their comparison with theory

In situ reactive compatibilization was first time applied to a low melting nylon (nylon 6 and 66 copolymer) and EPDM blend system. The effects of in situ compatibilization and concentration of compatibilizer on the morphology and mechanical properties of nylon/EPDM blends have been investigated. The influence of EPM‐g‐MA on the phase morphology was examined by the scanning electron microscopy (SEM) after preferential extraction of the minor phase. The SEM micrographs were quantitatively analyzed for domain size measurements. The compatibilizer concentrations used were 0, 1, 2.5, 5, and 10 wt%. The graft copolymer (nylon‐g‐EPM) formed at the interface showed relatively high emulsifying activity. A maximum phase size reduction was observed when 2.5 wt% of compatibilizer was added to the blend system. This was followed by a leveling‐off at higher loadings indicating interfacial saturation. The conformation of the compatibilizer at the interface was deduced based on the area occupied by the compatibilizer at the blend interface. The experimental compatibilization results were compared with theoretical predictions of Noolandi and Hong. It was concluded that the molecular state of compatibilizer at interface changes with concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties. Measurement of tensile properties shows increased elongation as well as enhanced modulus and strength up on compatibilization. At higher concentrations of compatibilizer, a leveling‐off of the tensile properties was observed. A good correlation has been observed between the mechanical properties and morphological parameters. Copyright © 2007 John Wiley & Sons, Ltd.     

Characterization of irradiation-induced crosslink of epoxidised natural rubber/ethylene vinyl acetate (ENR-50/EVA) blend

The effect of irradiation on tensile, dynamic mechanical properties, thermal properties and morphology of ENR-50, EVA and ENR-50/EVA blend was investigated. All the samples were irradiated using a 3.0 MeV electron beam (EB) machine with doses ranging from 20 to 100 kGy. Results indicate that the gel fraction of ENR-50, EVA and ENR-50/EVA blend increases with irradiation dose. Concerning tensile properties, it can be seen that EB radiation increases the tensile strength of all the samples, increases the elongation at break of ENR-50 and ENR-50/EVA blend, reduces the elongation at break of EVA, increases M200 (modulus at 200% strain) of ENR-50 and EVA, while decreases M200 of the ENR-50/EVA blend. For dynamic mechanical studies, it was found that EB radiation increases the T_g of all the samples due to the effect of irradiation-induced crosslinking. The compatibility of ENR-50/EVA blend also found to be improving upon irradiation. In the case of thermal properties, it was detected that T_m, T_c and the degree of crystallinity of ENR-50/EVA blend increase with an increase in irradiation dose. This was due to the perfection in the crystal growth occurring upon radiation. Morphology changes play a major role in the changes of the properties of ENR-50/EVA blend. Finally, it can be concluded that ENR-50/EVA blend can be vulcanized by EB radiation.     

Gamma Irradiation Effects on Mechanical and Thermal Properties and Biodegradation of Poly(3-hydroxybutyrate) Based Films

Summary: Their biodegradable properties make polyhydroxyalkanoates (PHAs) ideal candidates for innovative applications. Many studies have been primarily oriented to poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-valerate) (PHBV) and afterwards to blends of PHAs with synthetic biodegradable polymers, such as poly(ε-caprolactone) (PCL). Medical and pharmaceutical devices require sterilization and γ irradiation could provide a proper alternative since it assures storage stability and microbiological safety. This contribution presents the effect of γ irradiation on the mechanical and thermal properties and on the biodegradation of PHB, PHBV and a commercial PHB/PCL blend. Samples, prepared by compression moulding, were irradiated in air at a constant dose rate of 10 kGy/h, from 10 to 179 kGy. Polymer chain scission was assessed by changes in the molecular weight, thermal properties and tensile behaviour. The correlation between absorbed dose and changes in the mechanical properties and biodegradation is discussed in detail. The optimum dose to guarantee microbiological sterilization without damage of the structure or meaningful loss of the mechanical properties is also reported.     

Blends of starch with ethylene vinyl alcohol copolymers: effect of water,glycerol, and amino acids as plasticizers

Blends of thermoplastic starch with poly(ethylene‐co‐vinyl alcohol) copolymer (EVOH) were melt extruded with water/glycerol as plasticizer and a series of amino acid additives. The biggest factor in end‐use mechanical properties proved to be the relative humidity (RH) during storage. Plasticized starch‐EVOH blends stored at 0 and 50% RH changed significantly over time, with, for example, the tensile strength (TS) of the glycerol‐plasticized blend increasing from 4.7 to 26.3 MPa over 8 weeks when maintained at 0% RH. In contrast, the TS of this same sample stored at 75% RH remained unchanged for 8 weeks. Amino acids provided relatively minor, but significant changes in mechanical properties with time. Based on TS, elongation‐to‐break, and modulus, it may be concluded that β‐alanine, sarcosine, and L ‐proline were more effective than glycerol at maintaining strong flexible blends. Increases in crystallinity and changes in morphology with time, as described by modulated DSC were correlated to these changes in mechanical properties. Published in 2007 by John Wiley & Sons, Ltd.     

Synthesis and characterization of amphiphilic triblock copolymers by iron‐mediated atom transfer radical polymerization

The atom transfer radical polymerization of methyl methacrylate (MMA) and n‐butyl methacrylate (n‐BMA) was initiated by a poly(ethylene oxide) chloro telechelic macroinitiator synthesized by esterification of poly(ethylene oxide) (PEO) with 2‐chloro propionyl chloride. The polymerization, carried out in bulk at 90 °C and catalyzed by iron(II) chloride tetrahydrate in the presence of triphenylphosphine ligand (FeCl₂ · 4H₂O/PPh₃), led to A–B–A amphiphilic triblock copolymers with MMA or n‐BMA as the A block and PEO as the B block. A kinetic study showed that the polymerization was first‐order with respect to the monomer concentration. Moreover, the experimental molecular weights of the block copolymers increased linearly with the monomer conversion, and the molecular weight distribution was acceptably narrow at the end of the reaction. These block copolymers turned out to be water‐soluble through the adjustment of the content of PEO blocks (PEO content >90% by mass). When the PEO content was small [monomer/macroinitiator molar ratio (M/I) = 300], the block copolymers were water‐insoluble and showed only one glass‐transition temperature. With an increase in the concentration of PEO (M/I = 100 or 50) in the copolymer, two glass transitions were detected, indicating phase separation. The macroinitiator and the corresponding triblock copolymers were characterized with Fourier transform infrared, proton nuclear magnetic resonance, size exclusion chromatography analysis, dynamic mechanical analysis, and differential scanning calorimetry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5049–5061, 2005