Simulation of transient banded textures of sheared nematic polymers

Abstract

Nematic polymers, under certain conditions, develop a transient banded texture after cessation of simple shear flow when observing the sheared sample between crossed polars. Here we present a viscoelastic model that describes the formation mechanism of this well-characterized but yet unexplained phenomenon for a typical uniaxial rigid rod nematic polymer. It predicts that the relaxation of shear-flow enhanced scalar order parameter spatial fluctuations produces spatially periodic torques on the director, thereby producing a transient banded texture when viewing the sample between crossed polars. Our numerical results and digitized optical pattern are in good agreement with reported experimental observations.     

Optical pattern simulations for closed cylinders of liquid crystals

Abstract

Optical patterns for the polarizing microscope textures of closed cylinders of liquid crystals (CCLCs) are studied by the Jones vector formulation. The simulated director configuration diagram of a CCLC with normal orientation at the walls contains four kinds of stable director configurations. The resulting texture under some approximations depends only on phase shifts. The patterns are characterized by dark brushes that coincide with the directions of the crossed polarizers. Additionally, there are concentric circle fringes. For the ring defect structure, the centre region of the cylinder exhibits a black extinction. However, this is not distinguishable as between the hyperbolic and radial structures for both the point and the ring defect patterns. Comparing the observed patterns with the simulated ones, we find that the dark cross brushes and the centre black extinction of simulated patterns are similar to those that are observed. However, the concentric circle fringes of the observed pattern are not in accordance with the simulated pattern.     

Determination of the orientational ordering of 4′-cyanophenyl-4-alkylbenzoates by 13C NMR

Abstract

The orientational ordering of three 4′-cyanophenyl-4-alkylbenzoates (with number of carbons in the alkyl chain, n = 6,7 and 8; hereafter abbreviated as n-CPBs) has been investigated by ¹³C NMR. The order parameters of different molecular segments in the nematic phase of the n-CPBs were determined by the two-dimensional technique of separated local field (SLF) spectroscopy combined with off-magic-axis, variable-angle spinning (VAS) of the sample. The carbon-13 chemical shifts for each carbon nucleus in these compounds were determined by slowly spinning the sample parallel to the applied magnetic field. The order parameters obtained from SLF/VAS studies are linearly related to the corresponding anisotropic carbon-13 chemical shifts. These results provide a convenient way to obtain the order parameters for other homologous members of this liquid crystal series by direct measurement of only their carbon-13 chemical shifts in conjunction with the observed linear relationship between order parameters and chemical shifts.     

Simulation of transient banded textures of sheared nematic polymers

Nematic polymers, under certain conditions, develop a transient banded texture after cessation of simple shear flow when observing the sheared sample between crossed polars. Here we present a viscoelastic model that describes the formation mechanism of this well-characterized but yet unexplained phenomenon for a typical uniaxial rigid rod nematic polymer. It predicts that the relaxation of shear-flow enhanced scalar order parameter spatial fluctuations produces spatially periodic torques on the director, thereby producing a transient banded texture when viewing the sample between crossed polars. Our numerical results and digitized optical pattern are in good agreement with reported experimental observations.     

Comparison of the growth and degradation of poly(glycolic acid) and poly(ε‐caprolactone) brushes

The growth and degradation of poly(glycolic acid) (PGA) and poly(ε‐caprolactone) (PCL) brushes were compared. Using tin (octanoate) as the catalyst, optimal conditions were found for growth of each polyester brush from the hydroxy‐terminated silicon surface via ring‐opening polymerization. PCL brushes grew thicker at elevated temperatures but the thickest PGA brushes grew at room temperature. Unlike bulk polyesters that can degrade under both acidic and basic conditions, the confined surface polyester brushes only degraded under neutral or basic conditions. The degradation mechanism of grafted polyester brushes was probed through a blocking test. It was shown that the terminal hydroxy groups of these polyester brushes were essential to the degradation process indicating a preferential backbiting mechanism. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4643–4649     

Polar anchoring strengths of nematic liquid crystal on high-density polymer brush surfaces

ABSTRACT

Herein, the polar anchoring energy coefficient (A_θ) of nematic liquid crystal (NLC) was examined for high-density polymer brushes via capacitance measurements. The A_θ is 10^?4 J m^?2 for the brushes of poly(methyl methacrylate), poly(ethyl methacrylate) and poly(styrene). The value decreases to 10^?5 J m^?2 for poly(n-butyl methacrylate) and poly(hexyl methacrylate) with lower glass transition temperatures. However, each polymer brush displays a constant A_θ value over a temperature range of ?15°C to 90°C, which is hardly affected by the graft density and brush thickness. At 25°C, A_θ is 10 times greater than the corresponding azimuthal anchoring energy coefficient (A_φ); therefore, NLCs on polymer brushes can be preferentially aligned along the in-plane component of the applied field.     

Neutral and Charged Brushes Covalently Grafted from OH-Functionalized Mica Surfaces using Surface-Initiated ATRP – Swelling Investigation by AFM

Poly(acrylic acid) (PAA) and poly(tert-butyl acrylate) (PBA) brushes of various grafting densities were prepared via surface-initiated polymerization of tert-butyl acrylate on mica. PAA was prepared by hydrolyzing the PBA brushes. The swelling behavior of PBA and PAA brushes was studied as a function of grafting density by AFM. The swelling of the polymer layer was found to be higher for PAA in water than for the PBA sample swollen with DFM.     

Electrostatic repulsion between two parallel plates covered with polymer brush layers

An expression for the electrostatic repulsive force is obtained for two parallel similar plates immersed in an electrolyte solution at separation h covered with a uniformly charged polymer brush layer of intact thickness d _o under compression (h<2d _o) after the two brushes come into contact. It is assumed that when the two brushes come into contact, they are squeezed against each other but do not interdigitate. The electrostatic repulsive force is found to increase with decreasing h as 1/h for highly charged brushes and as 1/h ² for weakly charged brushes. This is in contrast to the interaction force between the brush layers before contact (h≥2d _o), which is essentially proportional to exp[−κ(h−2d _o)] (where κ is the Debye–Hückel parameter). It is also shown that the interaction force for highly charged brushes, which becomes independent of the electrolyte concentration, can be comparable in magnitude to the steric repulsive forces between the brushes resulting from osmotic repulsion and the elastic energy of the brushes. Received: 21 October 1998 Accepted in revised form: 25 December 1998     

Morphological studies on polybutylene terephthalate

The morphology of poly(butylene terephthalate) (PBT) crystallized from the melt at various temperatures was studied by small-angle light scattering, polarizing microscopy, and wide-angle x-ray diffraction. Spherulites with a maltese cross at 45° to the polars formed at lower temperatures while spherulites having an apparently higher melting point with a maltese cross along the polars (0°–90°) formed at higher temperatures. The spherulite size and crystallinity increased with increasing crystallization temperature. The H_v scattering patterns arising from the spherulites formed at lower temperature showed intensity maxima at azimuthal angles of 0° and 90°, while those obtained at higher temperatures showed the more common 45° intensity maxima. Microtomed samples from molded PBT bars showed spherulites with a 45° maltese cross which changed to a 0°–90° maltese cross upon heating just prior to melting. The skin-core effect due to varying thermal histories in these molded bars was clearly observed. Solvent crystallized films contained positive 0°–90° spherulites. Some changes occurring upon uniaxial stretching of PBT films are also discussed.     

X-ray diffraction study of the smectic mesophase of some azobenzene-containing polyacrylates

Abstract

An X-ray study is performed on powder specimens and on stretched oriented fibres of two liquid crystalline polyacrylates containing the azobenzene mesogenic unit with either a 4′-n-pentyloxy (sample 1–4) or 4′-n-hexyloxy (sample 1–5) substituent. The X-ray diffraction patterns of both samples showed the presence of a bilayer smectic C mesophase with the mesogneic groups tilted by an angle β ～ 45° (1–4) or β ～ 38° (1–5) with respect to the layer normal. The electron density profile p(z) along the direction normal to the smectic layers was calculated by Fourier inversion and possible structural models of the smectic mesophase are discussed. A partial interdigitation of the terminal alkyloxy substituents appears to occur.     

THE MORPHOLOGY AND STRUCTURE OF POLYETHYLENE TEREPHTHALATE SPHERULITES

The morphology and structure of three types of normal and abnormal spherulites of polyethylene terephthalate cast from solution in dimethylphthalate were studied by polarizing microscopy, transmission electron microscopy and electron diffraction techniques. In the normal negative spherulites the [0]~* direction is parallel to the radius direction. In the normal positive spherulites the radius direction is parallel to the [6]~*. In the abnormal PET spherulites the Maltese cross extinction pattern in the polarizing microscope under crossed polars is oriented at 45°to the polars and there are concentric extinction rings around the center of the spherulite. Electron diffraction pattern indicates that [2]~* is parallel to the radius of the spherulite and this explains the observed extinction pattern, in the abnormal spherulite.     

Structure development of fibers from liquid-crystalline PET/60PHB copolyester

Effect of extrusion conditions, particularly temperature, on the structure development of fibers from poly(ethylene terephthalate) modified with 60 mol% p-hydroxybenzoic acid was investigated. Light microscopy revealed that the structure of the liquid-crystalline fiber was highly dependent on the extrusion temperature: low-temperature-spun fibers exhibited a structure with domains or clusters of crystallites randomly oriented, whereas the fibers spun at high temperatures had a well-developed fibrillar texture. Anisotropy of the fibers, as evidenced by dichroism and by the variation of brightness or darkness of the fibers between crossed polars, was significantly higher for those spun at relatively high temperatures. Scanning electron microscopy revealed that the fibers spun at relatively low temperatures had poorly oriented, nonuniform morphology. Those produced at relatively high temperatures, on the other hand, consisted of well-developed fibrils. X-ray diffraction patterns showed that the molecular orientation increased with increasing extrusion temperature. A model for the development of fiber structure from thermotropic liquid-crystalline polymers is proposed.     

Flexoelectric response at defect sites in nematic inversion walls

Electric field experiments have been carried out on +1 and ?1 defects formed in alignment inversion walls, in a planarly aligned nematic phenyl benzoate. The results show that the defects are non‐singular in the core and exhibit a flexoelectric response to an applied d.c. or low frequency a.c. field. When the c‐director flux lines are circular, as in a +1 defect in a wall parallel to the easy axis, flexoelectro‐optic switching characterized by an azimuthal angle variation is observed. When the c‐director flux is radial, the response is seemingly through polar angle variations involving no rotation of the extinction brushes due to crossed polarizers. This conclusion follows from the field‐induced structural distortions observed at a ?1 defect having a combination of radial and tangential c‐director fields.     

Surfaces Coated with Polymer Brushes Work as Carriers for Histidine Ammonia Lyase

The immobilization of enzymes on solid supports is an important challenge in biotechnology and biomedicine. In contrast to other methods, enzyme deposition in polymer brushes offers the benefit of high protein loading that preserves enzymatic activity in part due to the hydrated 3D environment that is available within the brush structure. The authors equipped planar and colloidal silica surfaces with poly(2-(diethylamino)ethyl methacrylate)-based brushes to immobilize Thermoplasma acidophilum histidine ammonia lyase, and analyzed the amount and activity of the immobilized enzyme. The poly(2-(diethylamino)ethyl methacrylate) brushes are attached to the solid silica supports either via a “grafting-to” or a “grafting-from” method. It is found that the grafting-from method results in higher amounts of deposited polymer and, consequently, higher amounts of Thermoplasma acidophilum histidine ammonia lyase. All polymer brush-modified surfaces show preserved catalytic activity of the deposited Thermoplasma acidophilum histidine ammonia lyase. However, immobilizing the enzyme in polymer brushes using the grafting-from method resulted in twice the enzymatic activity from the grafting-to approach, illustrating a successful enzyme deposition on a solid support.     

Water Content of Hydrated Polymer Brushes Measured by an In Situ Combination of a Quartz Crystal Microbalance with Dissipation Monitoring and Spectroscopic Ellipsometry

Poly(methacryloyloxy ethyltrimethylammonium chloride) (PMETAC), poly(sulfopropylmethacrylate potassium salt), or poly(N‐isopropyl acrylamide) (PNIPAM) brushes are synthesized by means of the atom transfer radical polymerization technique from gold surfaces coated with a monolayer of the initiator ω‐mercaptoundecyl bromo isobutyrate. The brush growth is followed in situ and in real time by the combination of quartz crystal microbalance with dissipation technique (QCM‐D) and spectroscopic ellipsometry in a single device. The combination of QCM‐D and ellipsometry allows for the simultaneous determination of both the acoustic mass, m_acous, comprising the mass of the polymer and the solvent, and the optical mass, m_opt, which corresponds to the polymer mass alone. Brush hydration is calculated from the difference between the values obtained for m_acous and m_opt for each polymer synthesized. Brush hydration is then used to quantify the percentage of water released in the brush during collapse; a 30–40% release of water for PMETAC and PSPM brushes in 1 M NaCl and 80% for PNIPAM brushes when the temperature is increased to values above the lower critical solution temperature is observed.     

Dynamics of end-grafted polystyrene brushes in theta solvents

The dynamics of the concentration fluctuations in end-grafted polystyrene brushes in a theta solvent (cyclohexane) are probed by evanescent wave dynamic light scattering at different wavevectors q and temperatures. When the solvent quality changes from marginal to poor, the relaxation function C(q, t) exhibits strong effects as compared with the smooth variation of the brush density profile. From a single exponential above 50 °C, C(q, t) becomes a two-step decay function. The fast decay is still assigned to the cooperative diffusion albeit slower than in the good solvent regime whereas the slow nonexponential and nondiffusive process might relate to microsegragated and/or chain dynamics in the present polydisperse brush. The relaxation function of the present three brushes with different grafting density reveals similarities and disparities between wet brushes and semidilute polymer solutions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3590–3597, 2006     

Synthesis and stability of BODIPY‐based fluorescent polymer brushes at different pHs

We report a simple strategy for the grafting of poly(methacrylic acid) [poly(MAA)] brushes from silicon substrate by surface‐initiated RAFT polymerization and the subsequent coupling of BODIPY to these brushes to render them fluorescent. The poly(MAA) brushes were first generated by functionalization of hydrogen‐terminated silicon substrate with methyl‐10‐undecenoate which both leads to the formation of an organic layer covalently linked to the surface via Si? C bonds without detectable reaction of the carboxylate groups and couples to the polymerization initiator, followed by surface‐initiated RAFT polymerization of tert‐butyl methacrylate from these substrate‐bound initiator centers, and finally conversion of tert‐butyl groups to carboxylic acid groups. The poly(MAA) brushes were then made fluorescent by grafting a BODIPY derivative via an ester linkage. The stability of the BODIPY‐based fluorescent polymer brushes in buffer solutions at pH 6.0 to 12.0 with added salt was investigated by ellipsometry, fluorescence microscopy, grazing angle‐Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy. The results of these measurements indicated that the organic molecule‐initiator bond (ester linkage) is unstable and can be hydrolyzed resulting in detaching of the immobilized polymer from the silicon substrate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3586–3596     

A detailed analysis of the properties of radiolyzed proteinaceous amino acids

The thermal behaviour of 21 proteinaceous l-amino acids either as pristine samples and also as radiolyzed (3.2 MGy) samples was studied with the differential scanning calorimeter. The onset and peak melting point as well as the melting enthalpy of all samples before and after the radiation treatment was measured and reported. The residual amount of each amino acid survived to the radiation dose of 3.2 MGy (N _γ) was measured from the melting enthalpies before and after radiolysis and hence the radiation resistance of each amino acid has been determined. The radiolysis causes a systematic reduction of the melting enthalpy and a shift of the onset and peak melting point to lower values. It is shown that N _γ does not correlate with the melting points of the amino acids but shows a correlation with the entity of the shift of the melting point peaks occurred after radiolysis. Such correlation instead does not exist between the N _γ parameter and the onset melting points of the amino acids. An explanation of such lack of correlation was given. Furthermore, a general relationship has been found between the amino acids melting point peak measured on pristine samples and the melting point peaks after solid state radiolysis. Such relationship can be used to predict roughly the expected melting point after radiolysis at 3.2 MGy of any given amino acid. The last part of the study was dedicated in the attempt to find a correlation between the N _γ parameter and the amount of the amino acids survived the radiolysis R _γ as measured by spectropolarimetry (ORD spectroscopy). A general trend was found in the connection between the N _γ and R _γ parameters but not a very strong correlation.     

Synthesis,thermo-responsive micellization and caffeine drug release of novel PBMA-<Emphasis Type="Italic">b</Emphasis>-PNIPAAm block polymer brushes

Brush-like block copolymers with poly(t-butyl methacrylate) (PBMA) and poly(N-isopropylacrylamide) (PNIPAAm) as side arms, PBMA-b-PNIPAAm, were designed and synthesized via a simple free radical polymerization route. The chemical structure and molecular weight of these polymer brushes were characterized and determined by nuclear magnetic resonance (¹H NMR), Fourier transform infrared spectrometry (FTIR) and gel permeation chromatography (GPC). The micellar formation by these polymer brushes in aqueous solutions were detected by a surface tension technique, and the critical micelle concentration (CMC) ranged from 1.53 to 8.06 mg L⁻¹. The morphology and geometry of polymer micelles were investigated by transmission electron microscope (TEM) and dynamic light scattering (DLS). The polymer micelles assume the regularly-spherical core-shell structure with well-dispersed individual nanoparticles, and the particle size was in the range from 36 to 93 nm. The PNIPAAm segments exhibited a thermoreversible phase transition, so the resulting block polymer brushes were temperature-sensitive and the low critical solution temperature (LCST) was determined by UV-vis spectrometer at about 28.82–29.40°C. The characteristic parameters of the polymer micelles such as CMC, micellar size and LCST values were affected by their compositional ratios and the length of hydrophilic or hydrophobic chains. The evaluation for caffeine drug release behavior of the block polymer micelles demonstrated that the self-assembled micelles exhibited thermal-triggered properties in controlled drug release.