High-transmittance polymer-stabilised blue-phase liquid crystal display with double-sided protrusion electrodes

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-sided protrusion (DSP) electrodes structure is proposed. The oblique electric field between the protrusion electrodes inside both top and bottom glass substrates can induce more isotropic-to-anisotropic transition in the polymer-stabilised blue-phase liquid crystal (PS-BPLC) medium through Kerr effect than using the in-plane switching electrode. For the same electrode width, spacing and cell gap, the transmittance of PSBP-LCD with the DSP electrodes is ～29% higher than that using the IPS electrode.     

Low-voltage blue-phase liquid crystal display with diamond-shape electrodes

We propose a new electrode configuration, called diamond-shape in-plane switching, to lower the operation voltage of polymer-stabilised blue-phase liquid crystal (BPLC) displays (BPLCDs). The electrode structure is modified from conventional protruded IPS, where the strip protrusion is changed to diamond shape. By optimising the electrode gap and diamond length, we are able to obtain peak transmittance over 75% at 15 V. It enables single thin-film transistor (TFT) driving, and more importantly, this is based on an industrially proven BPLC material. That means good long-term stability, adequate TFT charging time for high-resolution displays and sub-millisecond response time and acceptable voltage-holding ratio for field sequential displays can be achieved simultaneously. Our device design helps accelerate the emergence of the long-awaited BPLCDs.     

Low-gamma shift asymmetrical double-side blue-phase liquid crystal display

ABSTRACT

A single-domain blue-phase liquid crystal display (BPLCD), which has asymmetrical double-side electrode structure, is proposed to reduce gamma shift. Firstly, the electro-optical curve and gamma shift of the proposed BPLCD are discussed under the comparison with conventional in-plane switching (IPS) BPLCD. And then, its gamma shift is investigated under various conditions. Compared with the conventional IPS-BPLCD, the operating voltage can be reduced by ~31%, and the transmittance is increased by ~6%. The indistinguishable gamma shift can be obtained under various electrodes’ sizes, when the cell gap is appropriate. The results also indicate that if the electrodes’ height and Kerr constant of BPLC increase, the operating voltage can be further reduced (only 9.6 V in this work), and the gamma shift almost do not change. Moreover, a certain misalignment between the top and bottom glasses are permitted, which is good for reducing the fabrication difficulty. In terms of viewing angle, the proposed BPLCD has an average contrast ratio of ~5000:1, and the gamma shifts at full viewing angles are all indistinguishable.     

Blue-phase liquid crystal display with high dielectric material

A blue-phase liquid crystal display (BPLCD) with low operating voltage and high transmittance is demonstrated by using a high dielectric material, which is used as an insulation layer or protrusion fixed on the pixel and common electrodes in in-plane switching (IPS) mode. The operating voltage is reduced to about 14 V and the transmittance is improved for the BPLCD with high dielectric constant protrusion. Compared with the conventional protrusion electrode structure, the proposed protrusion can make manufacturing process simple and easy because the electrode has no complex shape. The results will be significant in designing optimal BPLCDs.     

Transflective blue-phase liquid crystal display with dielectric protrusion

A transflective blue-phase liquid crystal display (TRBP-LCD) with dielectric protrusions is proposed. The dielectric protrusions are fixed on the in-plane-switching (IPS) electrodes. The potential drops very slowly in the dielectric protrusions, thus the total field penetrating depth is significantly enlarged and the operating voltage is lowered, which helps suppressing electrostriction effect. The different heights of the dielectric protrusions in the transmissive (T) and reflective (R) regions contribute to balance the optical phase retardation between the T and R regions. The simulation results verify that the proposed TRBP-LCD can achieve low operating voltage and good sunlight readability.     

Low-voltage blue-phase liquid crystal display with single-penetration electrodes

A blue-phase liquid crystal display (BPLCD) with single–penetration (S-P) electrodes is proposed to reduce the operating voltage. X-shape inclined-electric field is induced by the S-P electrodes with 2 ~ 3 μm height, which can lower the operating voltage by ~45%, and improve the transmittance compared with BPLCD with conventional in-plane electrodes. Moreover, the wide viewing angle and very small image distortion index can be obtained in this structure with a half-wave biaxial film. The proposed structure shows simple etching control and easy one-drop filling process of blue-phase liquid crystal compared with dual-convex-penetration electrodes.     

A transflective blue-phase liquid crystal display with alternate electrodes

A transflective polymer-stabilised blue-phase liquid crystal display (BP-LCD) with alternate electrodes is proposed. The alternate electrodes are composed of right triangle electrodes and slanted electrodes. To balance the optical phase retardation between the transmissive (T) and reflective (R) regions, the legs of the right triangle electrodes in the T region generate uniform horizontal electric field, the hypotenuses of the right triangle electrodes and slanted electrodes in the R region generate uniform oblique electric field. As result, the T and R regions obtain the same optical phase retardation. This display exhibits reasonably high transmittance, low operating voltage, wide viewing angle and well-matched voltage-dependent transmittance and reflectance curves.     

Transflective blue-phase liquid crystal display with polar opposite electrodes

A submillisecond response, wide view and single-cell-gap transflective (TR) display employing a blue-phase liquid crystal is proposed. The device employs polar opposite in-plane switching (IPS) electrodes. To balance the optical phase retardation between transmissive (T) and reflective (R) regions, the IPS electrodes are formed with unequal gaps in the two regions. This display exhibits reasonably high optical efficiency and well-matched voltage-dependent transmittance and reflectance curves.     

Single electro-optic curve for RGB colours in blue-phase liquid crystal display

The double-layer penetration electrode structure is proposed to obtain the low-operating voltage blue-phase liquid crystal display (BPLCD) with single electro-optic curve for red-green-blue (RGB) colours in every pixel, which is more suitable for the field-sequential-colour display. The different influences of electrode’s parameters and driving methods on the electro-optical properties of the proposed BPLCD are investigated. The results demonstrate that the operating voltage can be reduced from 53.80 V to 23.00 V for red colour. Besides, the coincident voltage-dependent transmittance curves for RGB colours are obtained by adjusting the applied voltage of sub-electrode. Thus, RGB lights can pass through every pixel with single electro-optic curve, which is good for resolution enhancement and single gamma driving. Besides, the maximum gamma shift of the proposed BPLCD is less than 0.1099 at 60° polar angle for the red colour, and the gamma shift difference between red and blue colours is only 0.0542. If the high dielectric constant material is used as the protrusion, the operating voltage can be further decreased, which is close to that of the BPLCD with wall-shaped electrode structure.     

A transflective and viewing angle controllable blue-phase liquid crystal display

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-side in-plane switching (DS-IPS) electrode structure is proposed. This structure shows the transflective characteristics because the bottom electrodes are made by aluminium material. For transflective displays, it exhibits a well-matched voltage-dependent transmission and reflection curves through designing the width and gap of the top electrodes. When a bias voltage is applied on the top electrodes, it exhibits as a good viewing angle controllable display.     

Low-voltage and high-transmittance blue-phase liquid crystal display with concave electrode

A low-voltage and high-transmittance blue-phase liquid crystal display (BPLCD) with concave electrodes is proposed. We use in-plane switching electrodes on the etched substrates to generate the concave electrodes. The proposed device can generate a strong in-plane field with a large horizontal component to increase the transmittance and reduce the operating voltage. As a result, a low voltage ~9 V and reasonably high transmittance ~71.7% can be achieved. Moreover, due to the generated multi-domain structures in the etched areas, this BPLCD can obtain a symmetric and wide viewing angle and the contrast ratio of 1000:1 is obtained over 60° viewing cone.     

Low voltage blue-phase liquid crystal display with insulating protrusion sandwiched between dual-layer electrodes

In order to lower the operating voltage of blue-phase liquid crystal display (BPLCD), a BPLCD with insulating protrusion, which is sandwiched between dual-layer electrodes, is proposed. There are four electrodes in this structure; thus, we investigate different driving methods to find a proper driving method. The effect of protrusion’s dielectric constant on operating voltage of the proposed BPLCD is explored under various electrodes’ parameters. As a result, the operating voltage of the proposed BPLCD with protrusion’s dielectric constant of 1,000 is 9.8 V, which is reduced by ~ 4.67× compared with that of conventional in-plane switching (IPS) BPLCD (45.8 V). Moreover, the zigzag electrode structure is adopted to reduce the large off-axis image distortion index. Besides, the azimuth distortion index is defined to describe the gamma shift between the minimum and maximum gamma shift curves at a certain polar angle. The results show that the off-axis image distortion index can be reduced to 0.0834, the azimuth distortion index is 0.0810 and the viewing cone of contrast ratio larger than 1,000:1 is over 50ºas the zigzag proposed BPLCD is used.     

Fast switching and luminance-controlled fringe-field switching liquid crystal device for vehicle display

ABSTRACT

Liquid crystal displays (LCDs) for vehicle displays should exhibit a fast response time in wide temperature range and wide-viewing angle in horizontal and downward directions without grey-scale inversion but limited brightness in the upward direction because the display images can be reproduced in the front window glass of a vehicle, affecting driver’s front visibility. Currently, fringe-field switching (FFS) liquid crystal device is widely commercialised for high resolution and wide-viewing-angle LCD; however, it needs to improve response times and limit the display brightness in the upward direction. As a solution, we propose a homogeneously aligned liquid crystal device in which liquid crystal director does tilt as well as twist deformation in a confined area by both vertical- and fringe-electric fields, exhibiting about two times faster decay response time than that of conventional FFS mode with suppressed luminance in the upward direction. The proposed liquid crystal device can be applied to LCDs for vehicle displays.     

Low gamma shift blue-phase liquid crystal display with electric field induced multi-domain electrode structure

ABSTRACT

To reduce the gamma shift of blue-phase liquid crystal display (BPLCD), the multi-domain electrode structure with four sub-electrodes is proposed. The effects of electrodes’ parameters on electro-optical curve and gamma shift are calculated, and the gamma shift and contrast ratio at full viewing-cone are also investigated. For the proposed protrusion BPLCD, the operating voltage is reduced by ~73%, and the transmittance is increased by ~20% compared with the conventional in-plane switching BPLCD. The results also show that the off-axis image distortion index can be reduced from 0.4318 to 0.0875 at the polar angle of 60°, and it works well under various electrodes’ sizes. Moreover, the indistinguishable gamma shift can be obtained at full viewing-cone for the proposed BPLCD, and the uniform light distribution and high contrast ratio can be obtained as well.     

A hysteresis-free polymer-stabilised blue-phase liquid crystal

We report a polymer-stabilised blue-phase liquid crystal (BPLC) in an in-plane-switching (IPS) cell with negligible hysteresis and good stability. Long ultraviolet (UV) wavelength and top-side (no IPS electrode) exposure create uniform polymer network, which in turn helps to suppress hysteresis. The effect of photoinitiator is also investigated. Although a BPLC precursor without photoinitiator requires a higher UV dosage to stabilise the polymer network, it is favourable for keeping high resistivity and reducing image sticking.     

Comparisons of the vector method and tensor method for simulating liquid crystal devices

In calculating the director configuration in a liquid crystal device, two methods are commonly employed: a vector model and a tensor model. In this paper, we compare and contrast these methods for liquid crystal devices consisting of a layer of liquid crystal sandwiched between two plates. We compare the reliability and accuracy of the results, the speed of computation and the complexity of implementations of each method.     

Low voltage and high transmittance transflective blue-phase liquid crystal display with opposite polar electrodes

A single-cell-gap transflective polymer-stabilised blue-phase liquid crystal display with opposite polar pixel electrodes on an etched substrate is proposed. In the proposed structure, the space between common electrodes is adopted as transmissive region, and the space above the common electrode is adopted as reflective region. By optimising the electrode parameters of the transmissive and reflective regions, well-matched voltage-dependent transmittance and reflectance curves can be obtained. In addition, the device has good performances of low operating voltage (~3.2 V), high optical efficiency and a wide viewing angle.     

Optimisation of blue-phase liquid crystal with protrusion

The optimised structures of blue-phase liquid crystal display (BPLCD) with various protrusions were discussed in this article. The voltage-dependent transmittances for the cell with four protrusion shapes, wall-shaped electrode, trapezoid electrode, double penetration electrode and elliptical electrode, are simulated. The electrode gap and width and protrusion height’s effects on the optimised cell gap and the corresponding operating voltage are calculated. The optimised cell has the lowest operating voltage and relative high transmittance. The results are significant on design BPLCD with low operating voltage.     

Polymer encapsulated and stabilised blue-phase liquid crystal droplets

Polymer-encapsulated–polymer-stabilised blue-phase liquid crystals (LCs) are investigated. Encapsulated droplets are formed in a polyvinyl alcohol solution by emulsification, and blue-phase (BP) LCs in the droplets are stabilised via the polymerisation of reactive monomers to extend the BP temperature range. Polymer stabilised droplets are found to cause the expansion of the BP temperature range from 53°C to below 0°C. The effects of composition on droplet formation and the electro-optical behaviour and morphological properties of these droplets are reported.     

The influence of diluter system on polymer-stabilised blue-phase liquid crystals

In the present work, diluter effects on the phase transition temperatures and electro-optical properties of the polymer-stabilised blue-phase liquid crystals with microsecond respond time have been carried out. The temperature range of polymer-stabilised blue-phase samples broadened over 50 K including room temperature. By increasing the concentration of diluter, the faster response time is obtained, but Kerr constant become smaller. These values are still two orders of magnitude larger than conventional Kerr materials such as nitrobenzene. The major bottleneck is the increased operating voltage. Hysteresis is sensitive to the diluter concentration and is slightly small for polymer network systems. For next-generation display technology, an optimal concentration of diluter plays a crucial role to a proper balance between response time and operation voltage.