Preparation of the polymer–clay nanocomposites in exfoliated state by interface stabilization

To suppress the repulsive interfacial energy between hydrophilic clay and a hydrophobic polymer matrix for polymer–clay nanocomposites, a third component of amphiphilic nature such as poly(?‐caprolactone) (PCL) was introduced into the styrene–acrylonitrile copolymers (SAN)/Na‐montmorillonite system. Once ?‐caprolactone was polymerized in the presence of Na‐montmorillonite, the successful ring‐opening polymerization of ?‐caprolactone and the well‐developed exfoliated structure of PCL/Na‐montmorillonite mixture were confirmed. Thereafter, SAN was melt‐mixed with PCL/Na‐montmorillonite nanocomposite, and the SAN matrix and PCL fraction were completely miscible to form a homogeneous mixture with retention of the exfoliated state of Na‐montmorillonite, exhibiting that PCL effectively stabilizes the repulsive polymer–clay interface and contributes to the improvement of the mechanical properties of nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 246–252, 2004     

Synthesis and characterization of liquid crystalline epoxy and co-polymerisation with a non-mesomorphic epoxy resin

A novel liquid crystalline epoxy resin based on the imine group was synthesised and structurally characterised by infrared (IR) and nuclear magnetic resonance (NMR) spectroscopy. The mesogenic behaviour of the monomer was measured by differential scanning calorimetry (DSC) and polarised optical microscopy (POM), and presented various textures in the extensive temperature range. Methyl nadic anhydride (MNA) was employed to cure the liquid crystalline epoxy resin and the curing process was investigated using POM and wide-angle X-ray diffraction (WAXD). Information about distribution of liquid crystalline epoxy resin in the blending system resulted from the FT-IR Imaging System, indicating that molecules of liquid crystalline epoxy resin can agglomerate to form anisotropic domains. The improvement in mechanical properties of diglycidyl ether of biphenol A (DGEBA) modified with liquid crystalline epoxy was achieved. Scanning electronic microscopy (SEM) showed that an extremely rough and highly deformed fracture surface can be obtained. DGEBA modified with liquid crystalline epoxy resin was characterised by dynamic mechanical analysis (DMA) for its thermal properties. The results indicate that the presence of the liquid crystal phase influences glass transition temperature (Tg).     

Preparation of highly exfoliated epoxy/clay nanocomposites by "slurry compounding": process and mechanisms

Epoxy/clay nanocomposites with a high degree of exfoliation were achieved using a so-called "slurry-compounding" process with which the dispersed state of clay in water can be successfully transferred to an epoxy matrix. In this process sodium montmorillonite was first exfoliated and suspended in water. This suspension was further treated with acetone to form a clay-acetone slurry followed by chemical modification using silane. The modified slurry was then mixed extensively with epoxy to form epoxy/nanoclay composites. It has been shown that the morphologies of clay before and after curing are quite similar and the exfoliation process is termed "slurry compounding". Furthermore, the amount of organic modifier used is only 5 wt % of clay, in contrast to conventional organoclays which normally contain at least 25-45 wt % of organic surfactant. The resulting epoxy/nanoclay composites exhibit a high degree of clay exfoliation and a better thermal mechanical property.     

Structure‐property relationships in exfoliated polyisoprene/clay nanocomposites

Structure‐property relationships in exfoliated polyisoprene (PI)/clay nanocomposites have been studied as a function of the clay concentration with rheometry, X‐ray diffraction, small‐angle X‐ray scattering, and transmission electron microscopy. The results presented here indicate that the interlayer spacing of layered silicates increases from 2 to at least approximately 14 nm because of the penetration of polymer molecules into the spacing between the silicate layers. The average aspect ratio (width/thickness) of the dispersed nanoplates is also estimated to be at least approximately 80. Additionally, the storage modulus of the nanocomposite exhibits frequency‐independent pseudo‐solidlike behavior above the percolation threshold [volume fraction of clay at the percolation threshold (?_p) = 0.02] and shows large enhancements (up to approximately six orders of magnitude) in comparison with the storage modulus of PI when the volume fraction of clay (?) is greater than ?_p. For the shear‐aligned PI/clay nanocomposites, an increase in the storage modulus with shear alignment is observed at ? < ?_p, whereas a decrease in the storage modulus is observed for ? > ?_p. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1000–1009, 2004     

Curing of liquid crystalline epoxy resins with a biguanide

This work extends the authors' investigations on liquid crystalline epoxy resins prepared from diglycidyl ether of 4,4′-dihydroxybiphenyl (DGE-DHBP) and aliphatic dicarboxylic compounds (ADC) or difunctional aromatic compounds. Syntheses and properties of these liquid crystalline epoxy resins are described elsewhere. In this paper a study on the curing reaction of the above mentioned liquid crystalline epoxy resins is presented. Ortho-tolylbiguanide was applied as the curing agent. The curing reactions were investigated by differential scanning calorimetry, microscopic observations and IR spectroscopy. Depending upon the temperature program of curing, it was possible to obtain polymeric networks with liquid crystalline order. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2739–2745, 1997     

Kinetics studies on the accelerated curing of liquid crystalline epoxy resin/multiwalled carbon nanotube nanocomposites

A new class of nanocomposite has been fabricated from liquid crystalline (LC) epoxy resin of 4,4′‐bis(2,3‐epoxypropoxy) biphenyl (BP), 4,4′‐diamino‐diphenyl sulfone (DDS), and multiwalled carbon nanotubes (CNTs). The surface of the CNTs was functionalized by LC epoxy resin (ef‐CNT). The ef‐CNT can be blended well with the BP that is further cured with an equivalent of DDS to form nanocomposite. We have studied the curing kinetics of this nanocomposite using isothermal and nonisothermal differential scanning calorimetry (DSC). The dependence of the conversion on time can fit into the autocatalytic model before the vitrification, and then it becomes diffusion control process. The reaction rate increases and the activation energy decreases with increasing concentration of the ef‐CNT. At 10 wt % of ef‐CNT, the activation energy of nanocomposite curing is lowered by about 20% when compared with the neat BP/DDS resin. If the ef‐CNT was replaced by thermal‐insulating TiO₂ nanorods on the same weight basis, the decrease of activation energy was not observed. The result indicates the accelerating effect on the nanocomposite was raised from the high‐thermal conductivity of CNT and aligned LC epoxy resin. However, at ef‐CNT concentration higher than 2 wt %, the accelerating effect of ef‐CNTs also antedates the vitrification and turns the reaction to diffusion control driven. As the molecular motions are limited, the degree of cure is lowered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Fully exfoliated layered silicate epoxy nanocomposites

Fully exfoliated layered silicate epoxy nanocomposites are reported in this article. The processing route that resulted in these fully exfoliated layered silicate epoxies is based on a combination of high‐shear mixing in the presence of acetone and ultrasonication. Homomogeneous and random dispersion of the individual silicate nanolayers in the epoxy is confirmed through transmission electron microscopy images spanning low to high magnification as well as by X‐ray diffraction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3981–3986, 2004     

Thermotropic liquid crystalline polyester nanocomposites via in situ intercalation polycondensation

A thermotropic liquid crystalline polyester (TLCP)/organoclay nanocomposite was synthesized via in situ intercalation polycondensation of diethyl‐2,5‐dihexyloxyterephthalic acid and 4,4′‐biphenol in the presence of organically modified montmorillonite (MMT). The organoclay, C18‐MMT, was prepared by the ion exchange of Na⁺‐MMT with octadecylamine chloride (C18‐Cl^?). TLCP/C18‐MMT nanocomposites were prepared to examine the variations of the thermal properties, morphology, and liquid crystalline phases of the nanocomposites with clay content in the range of 0–7 wt%. It was found that the addition of only a small amount of organoclay was sufficient to improve the thermal behavior of the TLCP hybrids, with maximum enhancement being observed at 1 wt% C18‐MMT. Copyright © 2008 John Wiley & Sons, Ltd.     

Organoclay/thermotropic liquid crystalline polymer nanocomposites. III. Effects of fully exfoliated organoclay on morphology,thermal, and rheological properties

A fully exfoliated organoclay in thermotropic liquid crystalline polymer (TLCP) based nanocomposite was prepared by a method combining ultrasonication, centrifugation, solution casting, and heat‐shearing separation. Morphological study showed that the organoclays of 15–25 nm in size dispersed uniformly in TLCP with fully exfoliated structures. The organoclays formed molecular level interactions with TLCP molecules. The interactions did not affect the liquid crystallinity and mesophase structure of TLCP, but they affected the thermal stability and thermal properties of TLCP, increasing the thermal stability and shifting the transition temperatures to the higher ends. Mechanical rheology investigations in the linear viscoelastic region showed that with the exfoliated organoclay in TLCP, more obvious pseudosolidlike behavior appeared in the terminal region. The rigidity of TLCP was enhanced by the presence of the exfoliated organoclay with percolated structures in the TLCP matrix. In steady shear tests, the nanocomposite had the similar shear viscosity and N1 (the first normal stress difference) to those of TLCP in the steady state condition. Percolated structures were easily destroyed by sufficient shear strain and the exfoliated organoclays were oriented along the shear direction, even assisting the neighboring TLCP molecules to align in the flow direction, resulting in a decrease of viscosity and an increase of the N1 slope. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 712–720, 2010     

Preparation and properties of highly birefringent liquid crystalline materials: styrene monomers with acetylenes,naphthyl, and isothiocyanate groups

Two new series of styrene monomers with different alkyl chain length were successfully synthesised. The chemical structures of synthetic intermediates and monomers were confirmed by Fourier transform infrared spectroscopy, ¹H nuclear magnetic resonance spectroscopy, mass spectrometry and elemental analysis. Their thermal stability, transition temperatures and phase sequences were investigated by polarised light microscopy, thermogravimetric analysis, differential scanning calorimetry and one-dimensional wide-angle X-ray diffraction. The birefringent and photoelectric properties, UV–vis and fluorescence spectroscopy were also measured using Abbe refractometer and fluorescent apparatus. The results indicated that all the monomers exhibited a liquid crystalline phase at higher temperature, high birefringence values between 0.4 and 0.7, and good photoluminescence properties. Optical anisotropy of homologous molecules was reduced with the increase of alkyl chain length due to the decrease of molecular polarisation. Moreover, a significant effect of the chemical structure on the photoluminescence properties was also found and discussed according to the length of π-conjugation.     

液晶环氧p-PEPB的合成及改性双酚-A环氧树脂的研究

本文以对羟基苯甲酸乙酯、丙烯溴、对苯二酚等为原料合成了双4-环氧丙基醚苯甲酸对苯二酚酯液晶环氧树脂(p-PEPB).用IR、1HNMR、DSC、POM和XRD的对其进行了表征,结果表明该化合物为向列型液晶,其熔点为180℃,清晰点为250 ℃.研究了 p-PEPB/双酚-A环氧(BPAER)/4,4,-二氨基二苯醚(DDE)体系的非等温固化过程,得到了固化温度参数、表观活化能Ea及p-PEPB含量对Tg的影响,结果表明p-PEPB为5%可使BPAER的Tg提高14 ℃,固化过程服从Ozawa模型.     

Effect of substituents on the curing of liquid crystalline epoxy resin

The synthesis of an aromatic ester based liquid crystalline epoxy resin (LCE) with a substituent in the mesogenic central group is described. Chlorine and methyl groups were introduced as substituents. The curing behaviors of three epoxy resins were investigated using diaminodiphenyl ester as the curing agent. The curing rate and heat of curing of LCE were measured with dynamic and isothermal DSC. The chlorine substituent accelerated the curing of LCE, while the methyl substituent decelerated the curing of LCE. The heat of curing of substituted LCE was diminished compared to LCE with no substituent. Glass transition temperature and elastic modulus of LCE decreased with increasing the size of the substituent. Three liquid crystalline epoxy resins based on aromatic ester mesogenic groups formed a liquid crystalline phase after curing, and the liquid crystalline phase was stable up to the decomposition temperature. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 911–917, 1998     

Preparation of highly exfoliated epoxy-clay nanocomposites by sol-gel modification

The objective of this work is to intercalate epoxy groups into the layered silicates through sol-gel reaction of cationic triethoxysilanepropylamineformylethyl trimethyl ammonium iodide (APS) and 3-glycidoxypropyl trimethoxysilane (GPS). When the ratio of APS to GPS was 1/4 or more, the organoclay was easier to be dispersed in acetone and formed stable slurry. The slurry was then mixed extensively with epoxy resin to form epoxy-nanoclay composites by photopolymerization. The resulting epoxy-nanoclay composites exhibited a high degree of clay exfoliation from ordered exfoliation to highly disordered exfoliation and a better thermal stability property.     

Synthesis and curing of liquid crystalline epoxy resin based on naphthalene mesogen

Aromatic liquid crystalline epoxy resin (LCE) based on naphthalene mesogen was synthesized and cured with aromatic diamines to prepare heat‐resistant LCE networks. Diaminodiphenylester (DDE) and diaminodiphenylsulfone (DDS) were used as curing agents. The curing reaction and liquid crystalline phase of LCE were monitored, and mechanical and thermal properties of cured LCE network were also investigated. Curing and postcuring peaks were observed in dynamic DSC thermogram. LCE network cured with DDE displayed liquid crystalline phase in the curing temperature range between 183 and 260°C, while that cured with DDS formed one between 182 and 230°C. Glass transition temperature of cured LCE network was above 240°C, and crosslinked network was thermally stable up to 330°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 419–425, 1999     

The mechanical and magnetic alignment of liquid crystalline epoxy thermosets

The processing of a new series of liquid crystalline (LC) epoxy networks was evaluated. Above the glass transition temperature, the low crosslink density networks could be mechanically aligned. The mechanically oriented networks readily lost orientation upon heating. Highly anisotropic liquid crystalline (LC) epoxy networks were also prepared by aligning the mesophase of the prepolymer during the curing process under the influence of a magnetic field. Orientation parameters (f) of 0.13 to 0.57 were achieved by these processes as determined by x-ray diffraction analysis. The ability of the magnetically aligned networks to retain their orientation above the glass transition temperature was determined by time-resolved x-ray diffraction. The stability of the alignment of these networks was found to depend on crosslink density. The effect of the anisotropy of these networks was investigated by measuring the coefficient of thermal expansion (CTE). In the aligned networks, there was a substantial reduction in CTE parallel to the direction of the applied field compared to the randomly oriented networks. © 1992 John Wiley & Sons, Inc.     

Synthesis and characterization of a series of thermotropic liquid crystalline copolyester nanocomposites

A series of aromatic thermotropic liquid crystalline copolyester (TLCP) nanocomposites were prepared by the in situ intercalation polymerization of p‐acetoxybenzoic acid (ABA), terephthalic acid (TPA), and diacetoxynaphthalene (DAN) isomers in the presence of the organoclay. The DAN isomers used in this study were 2,3‐ and 2,7‐naphthylene. We examined the variation of the liquid crystallinity, morphology, and thermal properties of the nanocomposites with organoclay content in the range 0–10 wt %. All the polymer nanocomposites were fabricated with a molar ratio of ABA:TPA:DAN = 2:1:1; they were shown to consist of a nematic liquid crystalline phase for low organoclay contents (≤5 wt %), whereas the hybrids with a higher concentration of organoclay (≥10 wt %) were found not to be mesomorphic. By using transmission electron microscopy, the clay layers in the 2,3‐DAN copolyester hybrids were found to be better dispersed in the matrix polymer than those in the 2,7‐DAN copolyester hybrids. The introduction of an organoclay into the matrix polymer was found to improve the thermal properties of the 2,3‐DAN copolyester hybrids. However, the thermal properties of the 2,7‐DAN copolyester hybrids were found to be worse than those of the pure matrix polymer for all organoclay compositions tested. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 387–397, 2006     

Liquid crystalline epoxy resins by polyaddition of aliphatic diepoxides with 4,4′-dihydroxybiphenyl

Liquid crystalline epoxy resins were synthesized from 4,4′-dihydroxybiphenyl (DHB), which was used as a mesogenic component, and diglycidyl ethers of aliphatic glycols (ethylene glycol and 1,6-hexanediol) which were used as flexible spacers. The synthesis was carried out by the catalytic polyaddition in the melt. Triphenylphosphine was used as the catalyst. The course of the polyaddition was investigated at various molecular ratios of the reactants. It was found that both linear and branched structures were formed in the course of the synthesis. The rates of the formation of the structures were calculated. The epoxy oligomers were investigated by DSC, polarizing microscope, and x-ray and IR spectroscopy. The molecular weight distribution was determined by GPC. The dependence of liquid crystalline properties of the obtained epoxy resins on the molecular weight and on the chain length of the flexible spacer was investigated. The molecular weight of the epoxy oligomers and the length of flexible spacer influence the phase transition temperatures. © 1995 John Wiley & Sons, Inc.     

Effects of liquid crystalline structure formation on the curing kinetics of an epoxy resin

The curing kinetics of a system containing 4,4′-diglycidyloxy-α-methylstilbene (DOMS) and different functionality amines, N-ethylaniline (NEA), aniline, benzenesulfonamide (BSA), and sulfanilamide (SAA), have been studied by differential scanning calorimetry (DSC) under isothermal conditions. The phase transformations during curing of the systems have been monitored by a crosspolarized optical microscope equipped with a hot-stage and photo detector. It has been found that the growth of a nematic liquid crystal structure does not cause a discrepancy from the autocatalytic model for the reactions between aniline and epoxy. There is no liquid crystalline structure formed for the systems containing NEA or BSA, which follow the autocatalytic kinetic models within the temperature range of 120–150°C. For the curing reactions between DOMS and SAA, there is a big deviation from the autocatalytic model when the liquid crystals transfer from a nematic structure to a smectic structure. Unlike the usual decrease of reaction rate resulting from diffusion in a heterogeneous reaction, the reaction rate is enhanced. A modified kinetic model has been constructed for this reaction system by introducing a pseudoconcentration term caused from the liquid crystalline structure formation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1105–1124, 1997     

Electro-optical properties of ferroelectric liquid crystalline polymers

Ferroelectric liquid crystalline polymers (FLCPs) were synthesized. These ferroelectricities were confirmed directly by measuring polarization reversal currents and other electro-optical properties. The smectic layer structure of FLCP was also studied. A chevron structure similar to that of low molecular weight FLC was observed even in an FLCP cell; but the zigzag defects were not so sharp, which means that it is easy to obtain a good orientation even in large-area displays.     

Synthesis and characterisation of a novel Y-shaped liquid crystalline epoxy and its effect on isotropic epoxy resin

ABSTRACT

A novel Y-shaped liquid crystalline epoxy with a rigid core with three flexible liquid crystalline arms (ETTPM) was synthesised and its structure was characterised by Fourier transform infrared spectroscopy and nuclear magnetic resonance (NMR) spectroscopy. It was analysed and observed by differential scanning calorimetry, X-ray diffraction and polarised optical microscopy (POM) that the liquid crystal phase was stable on the temperature range of 107.8°C. In particular, an unusual transition phenomenon of liquid crystal phases was observed. Modified epoxy-resin-cured products were prepared using ETTPM, epoxy resin E51 and 4,4-diaminodiphenyl methane. The liquid crystalline domains in cured products were observed by researching their scattering effect on laser. Mechanical tests showed that ETTPM was effective for the mechanical properties improvement of epoxy-resin-cured products, as demonstrated in the improvement of impact strength, tensile strength and tensile elasticity modulus. The impact fracture cross-sections and surface morphologies were studied further by POM and scanning electron microscopy (SEM). Crack deformation, crack split and notable plastic deformations were found in modified epoxy-resin-cured products, and these factors played important roles in improving the impact strength.