Gel permeation chromatography – Atmospheric pressure chemical ionization – Mass spectrometry for characterization of polymer additives

The study presents the possibility to use gel permeation chromatography (GPC) with atmospheric pressure chemical ionization (APCI)-mass spectrometry for the analysis of polymer additives having molecular weights up to 2,000?g?mol^?1. Irganox 1010, Irganox 1035, Irganox 1076, and Irganox 3114 were analyzed in chloroform using 2.1-mm-internal-diameter GPC columns at the optimum flow rate of 50?µL min^?1. Based on the chemical formula, the APCI interface combined with chlorine ionization enabled us to predict the expected mass spectrum and to build libraries without needing to inject each additive separately. Quantification limits of about 100?µg of additive in 1?g of polymer (100?ppm) can be reached using single-ion-monitoring methods based on the calculated isotope distribution.     

Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application.     

Comparison of negative chemical ionization and electron impact ionization in gas chromatography–mass spectrometry of endocrine disrupting pesticides

The study of pesticide residues belonging to endocrine disrupting chemicals (EDCs) (23 analytes of different chemical classes – organochlorines, organophosphates, pyrethroids, dicarboximides, phtalamides, dinitroanilines, pyrazole, triazinone) in apple matrix with conventional capillary GC–NCI-MS (with methane as reagent gas) in comparison to EI ionization is presented. For sample preparation QuEChERS method was applied. The lowest calibration levels (LCLs) for all pesticides were determined in both modes. Calibration in the NCI mode was performed at the concentration levels from 0.1 to 500 μg kg⁻¹ (R² > 0.999) and for EI in the range from 5 to 500 μg kg⁻¹ (R² > 0.99). From LCLs the instrumental limits of detection (LODs) and quantification (LOQs) were calculated. Chemometric study of pesticide signals in two MS modes was performed. Repeatability of all measurements, expressed by the relative standard deviations of absolute peak areas was better than 10% for the majority of compounds. Significantly lower values were obtained for the NCI mode.     

Fast gel permeation chromatography–mass spectrometry method for polymer and additive analysis

This study presents gel permeation chromatography (GPC) coupled with mass spectrometry (MS) as a suitable method to evaluate molecular weight distribution, oligomeric structure, and additives of commercial polystyrene resins in just 4?min. The chromatogram recorded by ultraviolet (UV) detection gives information on the high molecular mass fractions, while the mass detector provides knowledge on the chemical structure and concentration of oligomers and additives. A good agreement for the average molecular weights of the broad polystyrene reference SRM 706 and an excellent correlation with the expected isotope distributions for oligomers and additives were obtained using this fast GPC–UV–MS method.     

Comparison of electrospray ionization and atmospheric pressure chemical ionization for multi-residue analysis of biocides,UV-filters and benzothiazoles in aqueous matrices and activated sludge by liquid chromatography–tandem mass spectrometry

This paper describes the development of a multi-residue method for the determination of 36 emerging organic pollutants (26 biocides, 5 UV-filters and 5 benzothiazoles) in raw and treated wastewater, activated sludge and surface water using liquid chromatography–tandem mass spectrometry (LC–MS/MS). The target analytes were enriched from water samples adjusted to pH 6 by solid-phase extraction (SPE) on Oasis HLB 200 mg cartridges and eluted with a mixture of methanol and acetone (60/40, v/v). Extraction of freeze-dried sludge samples was accomplished by pressurized liquid extraction (PLE) using a mixture of methanol and water (50/50, v/v) as extraction solvent followed by SPE. LC–tandem MS detection was compared using electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) in positive and negative ionization mode. ESI exhibited strong ion suppression for most target analytes, while APCI was generally less susceptible to ion suppression but partially leading to ion enhancement of up to a factor of 10. In general, matrix effects could be compensated using stable isotope-labeled surrogate standards, indicated by relative recoveries ranging from 70% to 130%. In wastewater, activated sludge and surface water up to 33 analytes were detected. Maximum concentrations up to 5.1 and 3.9 μg L⁻¹ were found in raw wastewater for the water-soluble UV-filters benzophenone-4 (BZP-4) and phenylbenz-imidazole sulfonic acid (PBSA), respectively. For the first time, the anti-dandruff climbazole was detected in raw wastewater and in activated sludge with concentrations as high as 1.4 μg L⁻¹ and 1.2 μg g TSS⁻¹, respectively. Activated sludge is obviously a sink for four benzothiazoles and two isothiazolones, as concentrations were detected in activated sludge between 120 ng g TSS⁻¹ (2-n-octyl-4-isothiazolin-3-one, OIT) to 330 ng g TSS⁻¹ (benzothiazole-2-sulfonic acid, BTSA).     

Resin and fatty-acid analysis by solid-phase extraction coupled to atmospheric pressure chemical ionization–mass spectrometry

Abstract

DNA biosensors are realised immobilising a DNA structure on a suitable transducer to obtain selective information. In this paper we show how the determination of low-molecular weight compounds with affinity for DNA was measured by their effect on the oxidation signal of the guanine peak of calf thymus DNA immobilised on the electrode sensor and investigated by chronopotentiometric analysis. The DNA biosensor is able to detect known intercalating and groove binding compounds. Applicability to river water samples was demostrated.

Moreover, a piezoelectric sensor coupled to a short oligonucleotide can be used as detector of the hybridisation reaction. We show as a model the detection of a specific mutation in apolipoprotein E (ApoE) gene.

Biotinylated 23-mer probes were immobilised on the streptavidin coated gold surface of a quartz crystal; the protein was covalently bound to the thiol/dextran modified gold surface. The device was able to distinguish different synthetic oligonucleotides. The hybridisation reaction was also performed using real samples of DNA extracted from human blood and amplified by Polymerase chain reaction PCR. The extension of such procedure to samples of environmental interest is discussed.     

Application of pyrolysis–mass spectrometry and pyrolysis–gas chromatography–mass spectrometry with electron-ionization or resonance-enhanced-multi-photon ionization for characterization of crude oils

A novel analytical system for gas-chromatographic investigation of complex samples has been developed, that combines the advantages of several analytical principles to enhance the analytical information. Decomposition of high molecular weight structures is achieved by pyrolysis and a high separation capacity due to the chromatographic step provides both an universal as well as a selective and sensitive substance detection. The latter is achieved by simultaneously applying electron ionization quadrupole mass spectrometry (EI-QMS) for structural elucidation and [1 + 1]-resonance-enhanced-multi-photon ionization (REMPI) combined with time-of-flight mass spectrometry (ToFMS). The system has been evaluated and tested with polycyclic aromatic hydrocarbon (PAH) standards. It was applied to crude oil samples for the first time. In such highly complex samples several thousands of compounds are present and the identification especially of low concentrated chemical species such as PAH or their polycyclic aromatic sulfur containing heterocyclic (PASH) derivatives is often difficult. Detection of unalkylated and alkylated PAH together with PASH is considerably enhanced by REMPI–ToFMS, at times revealing aromatic structures which are not observable by EI-QMS due to their low abundance. On the other hand, the databased structure proposals of the EI-QMS analysis are needed to confirm structural information and isomers distinction. The technique allows a complex structure analysis as well as selective assessment of aromatic substances in one measurement. Information about the content of sulfur containing compounds plays a significant role for the increase of efficiency in the processing of petroleum.     

Assessing the suitability of a green solvent for gel permeation chromatography–mass spectrometry analysis

The study presents the possibility of performing the analysis of oligomeric structures and polymer additives by gel permeation chromatography (GPC) with atmospheric pressure chemical ionization (APCI) mass spectrometry (MS) in dibuthoxymethane (DBM, butylal), a halogen-free and less hazardous solvent than typically used chloroform and tetrahydrofuran. Polystyrene oligomers and Irganox® additives were analyzed in DBM using 2.1?mm internal diameter GPC columns, allowing to decrease the flow rate down to 50?µL/min, compatible with APCI–MS interface. The ionization was controlled by adding 1% chloroform in DBM to obtain (M+Cl)^? adducts, allowing a fast optimization of method parameters.     

Gel permeation chromatography clean-up for the determination of gestagens in kidney fat by liquid chromatography–tandem mass spectrometry and validation according to 2002/657/EC

A specific and sensitive method based on liquid chromatography–tandem mass spectrometry using atmospheric pressure chemical ionization (LC–APCI–MS/MS) has been developed for the determination of gestagens in kidney fat (medroxyprogesterone acetate, megestrol acetate and melengestrol acetate). The procedure involved a clean-up procedure with gel permeation chromatography (GPC). The analytes were analyzed by reversed-phase LC–MS/MS, in positive multiple reaction monitoring (MRM) mode, acquiring two diagnostic product ions from the chosen precursor for the unambiguous confirmation of the gestagens. The method was validated at the validation level of 1.0 ng/g. The accuracy and precision of the method were satisfactory. The decision limits CCα ranged from 0.20 to 0.22 ng/g while the detection capabilities CCβ ranged from 0.33 to 0.38 ng/g. The method proved to be sensitive and reliable and thus renders an appropriate mean for residue analysis studies.     

Analytical capabilities of high performance liquid chromatography – Atmospheric pressure photoionization – Orbitrap mass spectrometry (HPLC-APPI-Orbitrap-MS) for the trace determination of novel and emerging flame retardants in fish

A new analytical method was established and validated for the analysis of 27 brominated flame retardants (BFRs), including so called “emerging” and “novel” BFRs (EBFRs and NBFRs) in fish samples. High performance liquid chromatography (HPLC) coupled to Orbitrap mass spectrometry (Orbitrap-MS) employing atmospheric pressure photoionization (APPI) interface operated in negative mode was used for the identification/quantitation of contaminants. HPLC-Orbitrap-MS analysis provided a fast separation of selected analytes within 14 min, thus demonstrating a high throughput processing of samples. The developed methodology was tested by intralaboratory validation in terms of recovery, repeatability, linear calibration ranges, instrumental and method limits of quantitation (i-LOQ and m-LOQ), and where possible, trueness was verified by analysis of certified reference materials (CRMs). Recoveries of analytes were between 80 and 119%, while the repeatability in terms of relative standard deviations (RSDs) was in the range from 1.2 to 15.5%. The measured values for both analyzed CRMs agreed with the provided consensus values, revealing the recovery of reference concentrations in 72–119% range. The elaborated method met the sensitivity criterion according to Commission Recommendation 2014/118/EU on monitoring of BFRs in food products for majority of the compounds. The concentrations of polybrominated diphenyl ethers (PBDEs) in real samples determined by HPLC-APPI-Orbitrap-MS method and validated gas chromatography–high-resolution mass spectrometry (GC–HRMS) method were found to be in a good agreement.     

Orthogonal array optimization of microwave-assisted derivatization for determination of trace amphetamine and methamphetamine using negative chemical ionization gas chromatography–mass spectrometry

An orthogonal array design (OAD) was applied to optimize microwave-assisted derivatization (MAD) for analysis of trace amphetamine (AM) and methamphetamine (MA) by negative chemical ionization gas chromatography–mass spectrometry (NCI GC–MS). The 2,3,4,5,6-pentafluorobenzoyl chloride (PFBC) was used as a derivatization reagent. Experimental factors including solvent, microwave power, and irradiation time at four-levels were studied in 16 trials by OAD₁₆ (4⁴). The significance of these factors was investigated using analysis of variance (ANOVA) and percent contribution (PC). Solvent is statistically demonstrated a chief factor; microwave power and irradiation time are secondary factors. Under the optimum condition, calibration curve of AM is linear over a range from 0.01 to 100 ng mL⁻¹ with correlation coefficient 0.9988, and MA from 0.1 to 1000 ng mL⁻¹ with correlation coefficient 0.9951. The limit of detection (LOD) is 1.20 pg mL⁻¹ for AM and 13.04 pg mL⁻¹ for MA. An applicability of the method was tested by analyzing urine samples from amphetamine-type stimulants (ATS)-abusing suspects. Consequently, the OAD method not only optimizes the MAD condition for determination of trace AM and MA, but identifies the effects of factor solvent, microwave power and irradiation time on the MAD performance.     

Analysis of aldehydes in beer by gas-diffusion microextraction: Characterization by high-performance liquid chromatography–diode-array detection–atmospheric pressure chemical ionization–mass spectrometry

In this work, a recently developed extraction technique for sample preparation aiming the analysis of volatile and semi-volatile compounds named gas-diffusion microextraction (GDME) is applied in the chromatographic analysis of aldehydes in beer. Aldehydes—namely acetaldehyde (AA), methylpropanal (MA) and furfural (FA)—were simultaneously extracted and derivatized with 2,4-dinitrophenylhydrazine (DNPH), then the derivatives were separated and analyzed by high-performance liquid chromatography with spectrophotometric detection (HPLC–UV). The identity of the eluted compounds was confirmed by high-performance liquid chromatography–atmospheric pressure chemical ionization–mass-spectrometry detection in the negative ion mode (HPLC–APCI–MS). The developed methodology showed good repeatability (ca. 5%) and linearity as well as good limits of detection (AA–12.3, FA–1.5 and MA 5.4 μg L⁻¹) and quantification (AA–41, FA–4.9 and MA 18 μg L⁻¹); it also appears to be competitive in terms of speed and cost of analysis.     

Simultaneous determination by ultra-performance liquid chromatography–atmospheric pressure chemical ionization time-of-flight mass spectrometry of nitrated and oxygenated PAHs found in air and soot particles

An ultra-performance liquid chromatographic-atmospheric pressure chemical ionization time-of-flight mass spectrometric (UPLC-APCIToFMS) method for rapid analysis of twelve nitrated polycyclic aromatic hydrocarbons (NPAHs) and nine oxygenated polycyclic aromatic hydrocarbons (OPAHs) in particle samples has been developed. The extraction step using pressurized liquid extraction was optimized by experimental design methods and the concentrated extracts were analyzed without further clean-up. Matrix effects resulting in suppression or enhancement of the response during the ionization step were not observed. The suitability of the developed method is demonstrated by analysis of six different particle samples including standard reference materials, atmospheric particles collected by a high-volume sampler at an urban background site, and a soot sample from a burner. Results from these measurements showed clear differences between the different kinds of samples. Concentrations from reference materials are in good agreement with those from previous studies. Additionally a clear seasonal trend could be observed in atmospheric NPAH and OPAH concentrations found in real samples, with higher concentrations in winter.     

Screening and quantification of pesticide residues in fruits and vegetables making use of gas chromatography–quadrupole time-of-flight mass spectrometry with atmospheric pressure chemical ionization

An atmospheric pressure chemical ionization source has been used to enhance the potential of gas chromatography coupled with quadrupole time-of-flight (QTOF) mass spectrometry (MS) for screening and quantification purposes in pesticide residue analysis. A screening method developed in our laboratory for around 130 pesticides has been applied to fruit and vegetable samples, including strawberries, oranges, apples, carrots, lettuces, courgettes, red peppers, and tomatoes. Samples were analyzed together with quality control samples (at 0.05 mg/kg) for each matrix and for matrix-matched calibration standards. The screening strategy consisted in first rapid searching and detection, and then a refined identification step using the QTOF capabilities (MS^E and accurate mass). Identification was based on the presence of one characteristic m/z ion (Q) obtained with the low collision energy function and at least one fragment ion (q) obtained with the high collision energy function, both with mass errors of less than 5 ppm, and an ion intensity ratio (q/Q) within the tolerances permitted. Following this strategy, 15 of 130 pesticides were identified in the samples. Afterwards, the quantitation capabilities were tested by performing a quantitative validation for those pesticides detected in the samples. To this aim, five matrices were selected (orange, apple, tomato, lettuce, and carrot) and spiked at two concentrations (0.01 and 0.1 mg/kg), and quantification was done using matrix-matched calibration standards (relative responses versus triphenyl phosphate used as an internal standard). Acceptable average recoveries and relative standard deviations were obtained for many but not all pesticide–matrix combinations. These figures allowed us to perform a retrospective quantification of positives found in the screening without the need for additional analysis. Taking advantage of the accurate-mass full-spectrum data provided by QTOF MS, we searched for a higher number of compounds (up to 416 pesticides) in a second stage by performing extra data processing without any new sample injection. Several more pesticides were detected, confirmed, and/or tentatively identified when the reference standard was unavailable, illustrating in this way the potential of gas chromatography–QTOF MS to detect pesticides in addition to the ones targeted in quantitative analysis of pesticides in food matrices. Figure

?     

Use of gel permeation chromatography for clean-up in the analysis of coccidiostats in eggs by liquid chromatography–tandem mass spectrometry

An analytical method for determination and confirmation of nine coccidiostatics in eggs is reported. Ethyl acetate is used as extraction solvent, with satisfactory results, and simple automated clean-up is based on gel-permeation chromatography (GPC) . The target compounds are then analysed by liquid chromatography–electrospray ionization–tandem mass spectrometry. The method was validated in-house in accordance with Commission Decision 2002/657/EC. Trueness and precision were determined at four concentrations, and the mean errors obtained were <10 %, with relative standard deviations ranging from 3 to 18 %. For three non-authorized coccidiostatics (clopidol, ethopabate, and ronizadole), decision limit and detection capability were in the ranges 0.12–0.16 and 0.18–0.23 μg kg^?1, respectively. The results obtained prove the suitability of this new analytical method for routine monitoring of these substances in eggs.     

Environmental PAH analysis by gas chromatography–atmospheric pressure laser ionization–time-of-flight–mass spectrometry (GC-APLI-MS)

The application of polycyclic aromatic hydrocarbon (PAH) analysis by gas chromatography coupled with atmospheric pressure laser ionization and mass spectrometry (GC-APLI-MS) to environmental samples was investigated in the study. The limit of detection for 40 PAH in a standard mixture was 5–100 fg, demonstrating GC-APLI-MS to be a highly sensitive technique and more sensitive by a factor of 100–3,500 compared to GC-MS. Acenaphthylene and cyclopenta[cd]pyrene were not detectable <2,500 fg per injection. To make use of this very high PAH sensitivity, the technique was applied to samples of environmental interest with limited available sample amounts such as particulate matter (PM), soot and a sample from a bioaccumulation test with Lumbriculus variegatus. First, special sample preparation was necessary and ultrasonic extraction proved to be suitable, if a thorough clean-up was performed and plastic materials avoided. By GC-APLI-MS and GC-MS, 224 and 28 single PAH compounds were detected in PM, about 1,000 and 15 in birch soot, and 9 and 2 in worm tissue, respectively, revealing the enormous potential of the method. The selectivity of GC-APLI-MS was shown for a crude oil where >2,200 PAH were detected without any sample preparation.     

Comparison of various hyphenated chromatography — Mass spectrometry methods for the analysis of β-agonists

Summary Different chromatography — mass spectrometry techniques for the analysis of -agonists have been compared.Gas chromatography — mass spectrometry (electron impact) has been used, as also has liquid chromatography coupled to the mass spectrometer by either thermospray or electrospray interfaces. The results obtained by the three method were compared in terms of sensitivity, selectivity, and richness of information provided by the analysis. It was found that using electrospray ionization, very powerful analysis could be achieved with high sensitivity, thus providing significant potential for the analysis of -agonists.     

Application of pentafluorophenyl hydrazine derivatives to the analysis of nabumetone and testosterone in human plasma by liquid chromatography–atmospheric pressure chemical ionization–tandem mass spectrometry

Two carbonyl compounds, nabumetone and testosterone, were derivatized with pentafluorophenyl hydrazine (PFPH) and analyzed by atmospheric-pressure chemical-ionization mass spectrometry. The PFPH derivatives underwent dissociative electron capture in negative-ion APCI (ECAPCI) and gave intense [M–20]^– ions in the mass spectra. In positive-ion APCI, the PFPH derivatives underwent efficient protonation and gave intense [M+H]⁺ ions in the mass spectra. In CID, the major product ions of the [M–20]^– ions in ECAPCI corresponded to the partial moiety of PFPH. In contrast, the major product ions of [M+H]⁺ corresponded to the partial moiety of the analyte. By using selected reaction monitoring (SRM) detection, low pg of nabumetone (1 pg) and testosterone (7 pg) could be detected in both ECAPCI and positive-ion APCI. In comparison with the detection limits (SRM) of the underivatized analytes, use of the PFPH derivatives resulted in 2500-fold and 35-fold sensitivity enhancements for nabumetone and testosterone, respectively. The PFPH derivatives were applied to the analysis of nabumetone and testosterone in human plasma by both ECAPCI and positive-ion APCI and were found to enable detection of 0.1 ng mL^–1 nabumetone in spiked plasma. For testosterone, endogenous testosterone in female plasma was detected in both ECAPCI and positive-ion APCI.