An ionic liquid-type carbon paste electrode for electrochemical investigation and determination of calcium dobesilate

An ionic liquid-type carbon paste electrode (IL-CPE) had been fabricated by replacing non-conductive organic binders with a conductive room temperature ionic liquid, 1-pentyl-3-methylimidazolium hexafluorophosphate (PMIMPF₆). The electrochemical responses of calcium dobesilate were investigated at the IL-CPE and the traditional carbon paste electrode (T-CPE) in 0.05 mol L⁻¹ H₂SO₄, respectively. The results showed the superiority of IL-CPE to T-CPE in terms of provision of higher sensitivity, faster electron transfer and better reversibility. A novel method for determination of calcium dobesilate was proposed. The oxidation peak current was rectilinear with calcium dobesilate concentration in the range of 8.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹, with a detection limit of 4.0 × 10⁻⁷ mol L⁻¹(S/N = 3) by differential pulse voltammetry. The proposed method was applied to directly determine calcium dobesilate in capsule and urine samples.     

Ferrocene-mediated carbon paste electrode modified with d-fructose dehydrogenase for batch mode measurement of d-fructose

A mediated modified carbon paste and renewable surface electrode for fructose amperometric measurement based on d-fructose dehydrogenase (FDH) was prepared and optimized. Commercially available ferrocene (FcH) and hydroxymethyl ferrocene (FcCH₂OH) were used as mediators. The substituted FcH showed better linearity and higher sensitivity. The influence of different experimental parameters was studied for optimum analytical performance. The final FDH-modified electrode showed good analytical performance for batch mode measurements of fructose.     

Potentiometric determination of hydrogen peroxide at MnO2-doped carbon paste electrode

A novel hydrogen peroxide (H₂O₂) potentiometric sensor, made with a MnO₂-doped carbon paste electrode (CPE), is reported. Under optimum conditions, the electrode gives a Nernstian response for H₂O₂ in the concentration range 3.00×10⁻⁷–3.63×10⁻⁴ mol/l, with a slope of 21–19.4 mV/pH₂O₂ and a detection limit of 1.2×10⁻⁷mol/l H₂O₂. In addition, this sensor offers some analytical characteristics such as sensitivity, good reproducibility and a simple preparation procedure. The effects of both the components of the electrode and other conditions on the potential response of the sensor, as well as the possible response mechanism, are discussed.     

An electrochemiluminescent sensor for glucose employing a modified carbon nanotube paste electrode

A carbon nanotube paste (CNTP) electrode and a carbon nanotube paste/glucose oxidase (CNTP/GOx) electrode were prepared, and the electrochemiluminescent (ECL) behavior of luminol in the presence of glucose was investigated in detail at each of these electrodes. Compared to the classical carbon paste (CP) electrode, the CNTP electrode incorporating glucose oxidase greatly enhanced the response of the ECL sensor to glucose due to the electrocatalytic activity of the carbon nanotubes, the specificity of the enzymatic reaction, and the sensitivity of the luminol ECL reaction. Under optimal conditions, the electrode was found to respond linearly to glucose in the concentration range 1.0x10(-6) approximately 2.0x10(-3) mol/L, and the detection limit (defined as the concentration that can be detected at a signal-to-noise ratio of 3) was found to be a glucose concentration of 5.0x10(-7) mol/L. The method used to prepare the CNTP/GOx electrode was very convenient, and the electrode surface could be renewed in the case of fouling by simply polishing or cutting it to expose a new and fully active surface. The relative standard deviations (RSD) were found to be 6.8% and 8.9% for the CNTP electrode and the CNTP/GOx electrode (n=6). The electrode retained 95% of its initial response after two weeks.     

嵌入式超薄化学修饰碳糊电极及抗坏血酸的电化学行为研究

以镍铬合金为基体,在其表面构建了嵌入式超薄邻啡口罗啉修饰碳糊电极,以扫描电镜表征电极形貌、电化学技术研究电极的电化学性质。该电极对抗坏血酸(AA)有灵敏的响应,在pH 2.0的B.R.缓冲溶液中,AA的氧化峰电流与其浓度在1.0×10-7~1.0×10-4mol/L范围内呈良好的线性关系,检出限为6.0×10-8mol/L。该电极可用于AA的电化学测量。     

芬苯达唑在石墨烯与[Bupy]PF_6复合修饰碳糊电极上的电化学性质及电分析方法研究

本文研究了芬苯达唑(Fenbendazole,FBZ)在石墨烯(RGO)与离子液体(N-丁基吡啶六氟磷酸盐)复合修饰碳糊电极上的电催化氧化及电化学动力学性质。同时用CC法(计时库仑法)、计时电流法(CA)测定FBZ在RGO-[Bupy]PF6/CPE上的电极反应动力学参数,并用方波伏安法(SWV)测定FBZ氧化峰电流(Ip)与其浓度c在4.0×10-8~1.0×10-5mol·L-1范围内呈良好线性关系,线性回归方程为Ip(μA)=1.471+5220.78c(10-3mol·L-1),R=0.9995,检测限(S/N=3)为1.4×10-9mol·L-1,在此基础上用SWV法对FBZ片剂中FBZ含量进行了电化学定量测定,RSD在0.2%~0.9%之间,回收率在99.0%~101.4%之间。     

Electrochemical behavior and detection of guanine using a sodium montmorillonite-modified carbon paste electrode

Herein, a sodium montmorillonite-modified carbon paste electrode is described for the electrochemical determination of guanine. Guanine yields a well-defined and very sensitive oxidation peak at the sodium montmorillonite-modified carbon paste electrode. Compared with the unmodified carbon paste electrode, the modified electrode facilitates the electron transfer of guanine, since it notably increases the oxidation peak current and lowers the oxidation overpotential of guanine. Based on this, a simple sensitive reliable electrochemical method is proposed for the detection of guanine after all the experimental parameters, such as solution pH value, sodium montmorillonite content in the carbon paste electrode, accumulation potential, and time, are optimized. Under the optimized conditions, the oxidation peak current of guanine varies linearly with its concentration in the range 5.0×10⁻⁸ to 2.0×10⁻⁵ M and the detection limit (signal-to-noise=3) is 2.0×10⁻⁸ M after 4-min accumulation. This method is successfully demonstrated with urine samples. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 2, pp. 178–182. The text was submitted by the authors in English.     

New triiodomercurate-modified carbon paste electrode for the potentiometric determination of mercury

A new tetrazolium-triiodomercurate-modified carbon paste electrode has been described for the sensitive and selective determination of mercury. The electrode shows a stable, near-Nernstian response for 1×10⁻³ to 6×10⁻⁶ M [HgI₃]⁻ at 25 °C over the pH range of 4.0-9.0, with an anionic slope of 55.5±0.4 mV. The lower detection limit is 4×10⁻⁶ M with a fast response time of 30-50 s. Selectivity coefficients of a number of interfering anions and iodo complexes of some metal ions have been estimated. The interference from many of the investigated ions is negligible. The determination of 1-200 μg/ml of mercury in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 50.0 μg/ml. The direct determination of mercury in spiked wastewater, metal amalgams and dental alloy gave results that compare favorably with those obtained by the cold vapor atomic absorption spectrometric method. Potentiometric titration of mercury and phenylmercury acetate with standard potassium iodide has been monitored using the developed triiodomercurate-carbon paste electrode (CPE) as an end point indicator electrode.     

Sequential injection/electrochemical immunoassay for quantifying the pesticide metabolite 3,5,6-trichloro-2-pyridinol

An automated and sensitive sequential injection electrochemical immunoassay was developed to monitor a potential insecticide biomarker, 3,5,6-trichloro-2-pyridinol. The current method involved a sequential injection analysis (SIA) system equipped with a thin-layer electrochemical flow cell and permanent magnet, which was used to fix 3,5,6-trichloro-2-pyridinol (TCP) antibody coated magnetic beads (TCP-Ab-MBs) in the reaction zone. After competitive immunoreactions among TCP-Ab-MBs, TCP analyte, and horseradish peroxidase (HRP) labeled TCP, a 3,3′,5,5′-tetramethylbenzidine dihydrochloride and hydrogen peroxide (TMB-H₂O₂) substrate solution was injected to produce an electroactive enzymatic product. The activity of HRP tracers was monitored by a square wave voltammetric scanning electroactive enzymatic product in the thin-layer flow cell. The voltammetric characteristics of the substrate and the enzymatic product were investigated under batch conditions, and the parameters of the immunoassay were optimized in the SIA system. Under the optimal conditions, the system was used to measure as low as 6 ng L⁻¹(ppt) TCP, which is around 50-fold lower than the value indicated by the manufacturer of the TCP RaPID Assay^® kit (0.25 μg/L, colorimetric detection). The performance of the developed immunoassay system was successfully evaluated on tap water and river water samples spiked with TCP. This technique could be readily used for detecting other environmental contaminants by developing specific antibodies against contaminants and is expected to open new opportunities for environmental and biological monitoring.     

Voltammetric determination of 2-nitrophenol at a bentonite-modified carbon paste electrode

A bentonite-modified carbon paste electrode has been applied to the determination of 2-nitrophenol by differential pulse voltammmetry. The electrochemical reduction of 2-nitrophenol at –0.8 V is carried out in an artificial sea water-formic acid/sodium formate medium at pH 4. The peak height was found to be dependent on the pH over the range 2–11; the presence of a secondary process was observed in the pH range 8–11. The peak potential showed a dependence on pH, with two linear regions with different slopes. A linear relationship between peak intensity and concentration was obtained in the range 0.07–10 mgl^–1, with a detection limit of 0.03 mg 1^–1 and a coefficient of variation of 1.3% at 5 mg 1^–1. The effects of organic and inorganic species on the 2-nitrophenol determination were studied with a view to testing the resolution of the voltammetric technique. The proposed method has been applied to sea water samples with good results.     

SMV在SDBS自组装膜与RGO复合修饰碳糊电极上的电催化氧化及电分析研究

研究了辛伐他汀(SMV)在表面活性剂十二烷基苯磺酸钠(SDBS)自组装膜与石墨烯(RGO)复合修饰碳糊电极(SDBS-RGO/CPE)上的电催化氧化和电化学动力学性质。实验结果表明,SDBS-RGO/CPE对SMV电化学氧化具有良好的催化作用。同时用循环伏安法(CV),计时电流法(CA)测定了SMV在SDBS-RGO/CPE上的电极反应动力学参数,用方波伏安法(SWV)测得SMV氧化峰电流(I pa)与其浓度在6.0×10-5～4.5×10-4mol·L-1范围内呈良好线性关系,检测限(S/N=3)为5.0×10-6mol·L-1,同时运用该方法对市售辛伐他汀片剂中SMV含量进行了电化学定量测定,测定结果符合定量测定要求。     

Immobilization of horseradish peroxidase to a nano-Au monolayer modified chitosan-entrapped carbon paste electrode for the detection of hydrogen peroxide

A procedure for fabricating an enzyme electrode has been described based on the effective immobilization of horseradish peroxidase (HRP) to a nano-scaled particulate gold (nano-Au) monolayer modified chitosan-entrapped carbon paste electrode (CCPE). The high affinity of chitosan entrapped in CCPE for nano-Au associated with its amino groups has been utilized to realize the use of nano-Au as an intermediator to retain high bioactivity of the enzyme. Hydrogen peroxide (H₂O₂) was determined in the presence of hydroquinone as a mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano-Au displayed excellent electrocatalytical activity to the reduction of H₂O₂. The effects of experimental variables such as the operating potential of the working electrode, mediator concentration and pH of measuring solution were investigated for optimum analytical performance by using an amperometric method. The enzyme electrode provided a linear response to hydrogen peroxide over a concentration range of 1.22×10⁻⁵-2.43×10⁻³ mol l⁻¹ with a sensitivity of 0.013 A l mol⁻¹ cm⁻² and a detection limit of 6.3 μmol l⁻¹ based on signal per noise =3. The apparent Michaelis-Menten constant (K_m^app) for the sensor was found to be 0.36 mmol l⁻¹. The lifetime, fabrication reproducibility and measurement repeatability were evaluated with satisfactory results. The analysis results of real sample by this sensor were in satisfactory agreement with those of the potassium permanganate titration method.     

Elaboration of carbon paste electrode containing pentadentate Nickel-(II) Schiff base complex: Application to electrochemical oxidation of thiosulfate in alkaline medium

A Nickel Schiff base complex, insoluble in water, was synthesized and used as modifier. A Nickel Schiff base modified carbon paste electrode MCPE was build. The electrodes were characterized by scanning electron microscopy (SEM), energy dispersive X-Ray spectroscopy (EDXS), cyclic voltammetry and chronoamperometry. The modifier is elctroactive, a well defined redox couple of Ni^III/Ni^II in alkaline medium was made in evidence. It presents a quasi-reversible system with electron transfer coefficient (0.38) and electron transfer rate of 4.5 s⁻¹. The electrogenerated Ni^III species on the surface of the electrode act as an excellent catalyst toward thiosulfate oxidation reaction with a chemical rate constant K_h equal to 23,6 M⁻¹s⁻¹. The different techniques involved in this study qualify our modified electrode as sensitive, reliable and very stable for thiosulfate analysis.     

亚硫酸盐在乙酰二茂铁修饰碳糊电极上的电催化氧化及其电化学动力学性质研究

研究了亚硫酸盐在乙酰二茂铁(AFc)修饰碳糊电极(AFc/CPE)上的电催化行为。研究结果表明,其在裸碳糊电极(CPE)上的行为比亚硫酸盐在AFc/CPE上的氧化峰电流增加约3倍,氧化峰电位负移360 mV,表明AFc/CPE对亚硫酸盐的电化学氧化具有良好的催化作用。用循环伏安法、计时电流法测定了亚硫酸盐在AFc/CPE上的电极过程动力学参数,测得电荷传递系数α为0.70,电催化氧化反应速率常数k为(4.91±0.05)×104(mol/L)-1.s-1。催化氧化峰电流与亚硫酸盐在5.0×10-4~1.1×10-2mol/L浓度范围内呈良好的线性关系,线性回归方程为Ipa(μA)=1.345 7.956c(10-3mol/L),R=0.9988,检出限为2.0×10-5mol/L。可用于亚硫酸盐的电化学定量测定方法。     

A new electrochemiluminescent detection system equipped with an electrically heated carbon paste electrode for CE

An electrochemiluminescent (ECL) detection system in CE with an electrically heated carbon paste electrode (CPE) was developed. This CPE could be heated by a 100 kHz alternating current (ac) generated from a function generator, and the temperature of the electrode (Te) could be controlled. To evaluate the feasibility and reliability of this system, the electrochemically generated Ru(bpy)(3) (3+)-based ECL reaction was used for detection of triethylamine (TEA) and tri-n-propylamine (TPrA). Ru(bpy)(3) (2+) was added into the separation buffer solution with precolumn mode. Effects of several important factors were investigated to acquire the optimum conditions. Under the optimum conditions, the heated electrode has been shown to provide advantages by the measurement of ECL intensity in CE at elevated Te. Compared with the conventional electrode at the room temperature, using heated CPE could improve peak shape and gain good reproducibility with lower detection limits and wider linearity ranges. Compared with the room temperature, the linear ranges and detection limits (S/N = 3) for TEA and TPrA were improved about one magnitude when the Te was 39 degrees C. In contrast, the RSD was lower than for the electrode at room temperature.     

固态碳糊电极电位法测定利多卡因注射液

本文报道了一种以利多卡因与单质碘形成的缔合物为电活性物的全固态碳糊利多卡因电极,电极的线性响应范围5.0×10-2～4.0×10-5mol.L-1,级差电位为30mV/pC,检测下限为3.0×10-5mol.L-1。该电极响应迅速,重现性好,用该电极测定了盐酸利多卡因注射液中利多卡因的含量,结果与药典法相符。     

Voltammetric study of 2-methyl-4,6-dinitrophenol at a modified carbon paste electrode

The voltammetric behavior of 2-methyl-4,6-dinitrophenol at a modified carbon paste electrode has been studied. Among the modifiers tested, hidepowder was found to give the best results. Cyclic voltammetry and differential pulse voltammetry were used to study the nature of the reaction; the possibility of accumulation of the analyte onto the electrode was studied by differential pulse voltammetry. An irreversible behavior and the adsorption of 2-methyl-4,6-dinitrophenol on the electrode were confirmed. The reduction signal shows two peaks. A linear relationship between the first peak height and the concentration of 2-methyl-4,6-dinitrophenol was obtained in the range 0.001–5 mg l⁻¹, with a detection limit of 3.2 μg l⁻¹ and a relative standard deviation of 3.20%. The interferences with the reduction peak of 2-methyl-4,6-dinitrophenol of several nitro- and chloro-phenols and inorganic species were tested.     

Study on the adsorptive catalytic voltammetry of aloe-emodin at a carbon paste electrode

Recently, the studies and applications for the pola-rographic catalytic waves of organic compounds at dropping mercury electrode made considerable head-way. Tovopova et al.[1―4] reported the polarographic catalytic waves of the organic compounds containi…     

Electrochemical behavior of mesoionic sydnone derivatives at wax-impregnated carbon paste electrode

The-N=N-moiety in the mesoionic 3-phenyl sydnone and its derivatives like tolyl sydnones and anisyl sydnones undergo two-electron irreversible electrochemical reduction in Britton-Robinson (BR) buffer at wax-impregnated carbon paste electrodes. Infrared, nuclear magnetic resonance, and mass-spectral data, used to characterize the reduced product, confirm the proposed mechanism. The pasting liquid at the surface of the electrode is found to decrease the electron-transfer rate and cause a higher overpotential compared to homogeneous electrodes. The influence of variation of pH on the peak current and peak potentials is studied in the acidic range. The cathodic peak shifts to more negative potentials with increase in pH, indicating the involvement of proton in the reduction process. This could be a new method of preparation of 2,4-dihydro-3-substituted 1,2,3-oxadiazole-5-one. The substituent effect and the effect of variation of scan rate, concentration, and temperature on peak currents and peak potentials is discussed. The cathodic shift in various organic co-solvents (methanol, acetonitrile, DMF, DMSO) using BRB as the supporting electrolyte is examined. Published in Russian in Elektrokhimiya, 2006, Vol. 42; No. 7, pp. 862–868. The text was submitted by the authors in English.