阻燃共聚酯/粘土复合物热降解动力学研究

用插层共聚方法合成了含磷共聚酯／粘土复合物。用热重(TG)方法考察热降解动力学。通过在空气中以不同的升温速率升温至设定温度,用Kissinger法和Hymn-Wall-Ozawa法对数据进行处理。结果表明,粘土组分含量较高的反应活化能较大,热稳定性较好。     

Preparation,structure, and property of polyoxymethylene/carbon nanotubes thermal conducive composites

Polyoxymethylene (POM)/multiwalled carbon nanotubes (MWNTs) nanocomposites were prepared through a simple solution‐evaporation method assisted by ultrasonic irradiation. To enhance the dispersion of MWNTs in POM, MWNTs were chemically functionalized with PEG‐substituted amine (MWNT‐g‐PEG), which exhibited strong affinity with POM due to their similar molecular structure. The thermal conductivity and the mechanical properties of the composites were investigated, which showed that the thermal conductive properties of POM were improved remarkably in the presence of MWNTs, whereas reduced by using MWNT‐g‐PEG due to the heat transport barrier of the grafted‐PEG‐substituted amine chain. A nonlinear increase of the thermal conductivity was observed with increasing MWNTs content, and the Maxwell‐Eucken model and the Agari model were used for theoretical evaluation. The relatively high effective length factor of the composite predicted with mixture equation indicated that there were few entangles of MWNTs for the samples of MWNT‐g‐PEG in the composites. The mechanical strength of the composites can be improved remarkably by using suitable content of such functionalized MWNTs, and with the increase of the aliphatic chain length of PEG‐substituted amine, the toughness of the composites can be enhanced. Transmission electron microscope result indicated that MWNT‐g‐PEG exhibited strong affinity with POM and a good dispersion of MWNTs was achieved in POM matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 905–912, 2010     

The thermal degradation kinetics of isomeric poly(dipropyl itaconates)

Non-isothermal thermogravimetry was performed in a dynamic nitrogen atmosphere, on a series of poly(di-n-propyl itaconates) (PDnPI) and poly(di-iso-propyl itaconates) (PDiPI) which had been prepared in the presence of various amounts of the chain transfer agentn-dodecyl mercaptan (DDM).Differential thermogravimetry (DTG) showed that both polymers degraded in two stages. The DTG curve of PDnPI had a large first peak followed by a smaller shoulder, whereas the DTG curve of PDiPI was composed of two peaks of almost equal heights. The addition of DDM during the polymerisations in both cases resulted in a similar decrease in the relative area of the first peak.     

Grafting of η-Cp(COOMe)MoCl(CO)3 on the surface of mesoporous MCM-41 and MCM-48 materials

η⁵-Cp(COOMe)MoCl(CO)₃ is grafted on the surface of mesoporous MCM-41 and MCM-48 materials through available silanol groups. The structural intactness of the supporting materials is confirmed by powder XRD and N₂ adsorption analysis. The presence of the Mo complex on the surface is confirmed by FT-IR and elemental analysis. The catalysts are successfully applied for cyclooctene epoxidation.     

Effect of nano cadmium sulfide on combustion and thermal decomposition of polystryene and poly(methyl methacrylate)

Cadmium sulfide nano particles, both hollow spheres (CdS‐HS) and rods (CdS‐NR), were synthesized by ultrasonic and solvothermal processes, respectively, and characterized by XRD and SEM. The effect of the two kinds of nano particles on flammability was investigated using the cone calorimeter and microscale combustion calorimeter. The incorporation of small amount of CdS nano particles (1 wt.%, 3 wt.%, 5 wt.%) leads to a reduction in the peak heat release rate (PHRR) compared to pristine PS; CdS‐NR is more efficient in reducing the PHRR. CdS nano particles are less effective in reducing the PHRR of PMMA. Thermal stability of PS/CdS and PMMA/CdS nanocomposites was studied by TGA. The TGA results show that the addition of the nano particles mainly increases thermal stability of PS and PMMA at high temperatures. Copyright © 2014 John Wiley & Sons, Ltd.     

Kinetics of thermal degradation and thermal oxidative degradation of poly(p-dioxanone)

The kinetics of the thermal degradation and thermal oxidative degradation of poly(p-dioxanone) (PPDO) were investigated by thermogravimetric analysis. Kissinger method, Friedman method, Flynn-Wall-Ozawa method and Coats-Redfern method have been used to determine the activation energies of PPDO degradation. The results showed that the thermal stability of PPDO in pure nitrogen is higher than that in air atmosphere. The analyses of the solid-state processes mechanism of PPDO by Coats-Redfern method and Criado et al. method showed: the thermal degradation process of PPDO goes to a mechanism involving random nucleation with one nucleus on the individual particle (F₁ mechanism); otherwise, the thermal oxidative degradation process of PPDO is corresponding to a nucleation and growth mechanism (A₂ mechanism).     

Zero‐order kinetics of the thermal degradation of polypropylene/clay nanocomposites

The thermal degradation kinetics of polypropylene/clay microcomposites and nanocomposites were studied by thermogravimetric analysis. In comparison with pure polypropylene, the reaction order of the degradation of the composites became zero‐order, and the activation energy increased dramatically. The zero‐order kinetics were associated with the acidic sites (H⁺) created on the clay layers, whereas the increase in the activation energy was coupled with the shielding effect of clay. The kinetic analysis could provide additional mechanistic clues concerning the thermal stability and flammability of polymer/clay nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3713–3719, 2005     

Optimization of mass spectrometry acquisition parameters for determination of polycarbonate additives,degradation products,and colorants migrating from food contact materials to chocolate

The interest towards “substances of emerging concerns” referred to objects intended to come into contact with food is recently growing. Such substances can be found in traces in simulants and in food products put in contact with plastic materials. In this context, it is important to set up analytical systems characterized by high sensitivity and to improve detection parameters to enhance signals. This work was aimed at optimizing a method based on UHPLC coupled to high resolution mass spectrometry to quantify the most common plastic additives, and able to detect the presence of polymers degradation products and coloring agents migrating from plastic re‐usable containers. The optimization of mass spectrometric parameter settings for quantitative analysis of additives has been achieved by a chemometric approach, using a full factorial and d‐optimal experimental designs, allowing to evaluate possible interactions between the investigated parameters. Results showed that the optimized method was characterized by improved features in terms of sensitivity respect to existing methods and was successfully applied to the analysis of a complex model food system such as chocolate put in contact with 14 polycarbonate tableware samples. A new procedure for sample pre‐treatment was carried out and validated, showing high reliability. Results reported, for the first time, the presence of several molecules migrating to chocolate, in particular belonging to plastic additives, such Cyasorb UV5411, Tinuvin 234, Uvitex OB, and oligomers, whose amount was found to be correlated to age and degree of damage of the containers.     

Study on the fluorescence and thermal stability of hybrid materials Eu(Phen)2Cl3/MCM-41

A series of luminescent hybrid materials Eu (Phen)₂Cl₃/MCM-41 that the different assembled mass of Eu(Phen)₂Cl₃ included into the channels of MCM, have been synthesized by combining ultrasound technology. The properties of the hybrid materials were characterized by XRD(X-ray Diffraction), N₂-adsorption-desorption, FT-IR and luminescence spectrum. The results show that the rare-earth compounds had been loaded into the holes of mesoporous material MCM-41. The luminescence intensities of the hybrid materials were improved as the increase of the loading concentration of the rare-earth complexes. The hybrid material has the maximal luminescence intensity when it reached the saturated loading concentration (7.17%). To compare with the pure rare-earth complex, the thermal stability of the hybrid materials were enhanced by about 100°C. __________ Translated from Chemical Research and Application, 2008, 20(1) (in Chinese)     

Fabrication of MCM-41 mesoporous silica through the self-assembly supermolecule of β-CD and CTAB

Using the self-assembly β-cyclodextrin (β-CD) and cetyltrimethylammonium bromide (CTAB) as structure-directing agents, high-quality ordered MCM-41 silicas have been prepared. Small-angle X-ray diffraction (SXRD), N₂ adsorption-desorption and scanning electron microscope (SEM) techniques were used to characterize the calcined samples. Results showed that the pore structure of the resulting mesoporous silica belonged to the two-dimensional hexagonal structure (space group p6mm). The high-quality hexagonal structure was formed as n?1 (n denotes molar ratio of β-CD to CTAB). N₂ adsorption-desorption curves revealed type IV isotherms, H4 hysteresis loops, for all samples, and H1 hysteresis loops for samples at n=0, 0.1, 1 and 2, respectively. The pore size and the pore wall thickness of the samples increased with the increase in n values, respectively.     

SiO2/COPs的合成及其在光催化反应中的协同效应

共价有机聚合物(COPs)是一类由轻质元素(C,H,O,N和B等)通过共价键的方式连接而成的有机多孔材料.COPs的共轭结构赋予其优异的可见光吸收特性,已经在光催化水分解制氢、二氧化碳还原、有机合成和污染物降解等领域显示出巨大的应用潜力.虽然COPs具有能带结构易调控和高孔隙率等优点,但其光催化活性仍有待提升.使用助催化剂是提升COPs的光催化活性,促进表面反应普遍采用的策略.此外,底物活化官能团的引入和光催化剂表面性质的调控也是提高光催化剂反应活性的有效方法.虽然可以通过改变COPs单体种类、化学键的类型和拓扑结构来调控COPs的组成,但要同时兼顾COPs的结构和亲疏水性的调控以及底物活化官能团的引入仍十分困难.与纯COPs相比,与其他材料进行杂化为扩大COPs的化学组成和功能性提供了更多可能.迄今为止,在COPs纳米孔中封装分子、纳米颗粒或将COPs涂覆在其他固体材料上是制备基于COPs复合材料的常用策略.但是,考虑到COPs和无机材料合成条件的不相容性,在纳米尺度精确控制复合材料的组分、结构和形貌仍然是一项艰巨的任务.本文制备了稳定在十六烷基三甲基溴化铵(CTAB)疏水核中的COPs胶体,其粒度分布在16 nm左右.通过溶胶-凝胶法在CTAB周围水解聚合四乙氧基硅烷,得到SiO2/COPs复合材料.表征结果表明,COPs均匀分布在氧化硅的骨架中.该复合材料具有分别来自于SiO2和COPs的介孔和微孔结构.与纯COPs相比,复合材料的表面疏水性降低.SiO2/COPs具有可见光响应特性,其吸收带边随COPs含量的增加而红移,表明在复合材料中COPs在高含量时发生团聚.SiO2/COPs作为光催化剂,可高效催化α-溴代苯乙酮的还原脱卤反应(汉斯酯为还原剂),其催化活性和SiO2/COPs比例相关,在COPs含量为22.6 wt％时达到最优.SiO2/COPs的催化活性较COPs有大幅度提高.在优化的SiO2/COPs比例下,SiO2/COPs的TOF是COPs的近12倍.控制实验表明,SiO2中的羟基对汉斯酯为还原剂有活化作用.此外,本文研究发现,复合材料的活性与SiO2/COPs的比值呈火山型曲线,表明在光催化反应中SiO2和COPs之间存在协同效应.由此可见,将光催化剂和反应物活化材料耦合是提高光催化反应活性的有效策略.     

Kinetics of thermal decomposition of PVC/fly ash composites

In this study, the kinetics and mechanisms of thermal degradation of Poly Vinyl Chloride (PVC) composites reinforced with class-F fly ash are studied experimentally and numerically using Flynn–Wall model. The addition of fly ash to the polymer matrix results in a decrease in the primary degradation temperature and an increase in the secondary degradation temperature. The metal oxides in the fly ash act as acid absorbers, which results in the destabilization of PVC during its dehydrochlorination process. However, they also react with the chlorine free radicals, which prevents the formation of HCl during degradation. In addition, it is observed that calcium and iron oxides, present in fly ash, are more reactive to the chlorine radicals rather than the silicon and aluminum oxides. The effect of fly ash chemical composition on the degradation of PVC composites was studied by comparing the thermal properties of composites containing two different classes of fly ashes, class-F and class-C, at similar levels. Thermal stability of the composites is found to be dependent on the chemical composition of fly ash. Higher dehydrochlorination rate is observed in the case of composites filled with class-F fly ash than those reinforced with class-C fly ash.     

Preparation and properties of polycarbonate/polyhedral oligomeric silsesquioxanes (POSS) hybrid composites

Octaphenylsilsesquioxane (PH‐POSS) and octa(γ‐methacryloxypropyl)silsesquioxane (MA‐POSS) were successfully synthesized by hydrolytic condensation of phenyltrichlorosilane and γ‐methacryloxypropyltrimethoxysilane, and characterized by Fourier transform infrared (FT‐IR), ¹H and ²⁹Si nuclear magnetic resonance (NMR), and matrix‐assisted laser desorption/ionization‐time of flight (MALDI‐TOF) mass spectrum. Morphology, degradation behavior, thermal, and mechanical properties of hybrid composites were studied by transmission electron microscopy (TEM), polarized optical microscopy (POM), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), surface contact angle (SCA), tensile, and impact testing. Domains of PH‐POSS and MA‐POSS dispersed in the matrix with a wide size distribution in a range of 0.1–0.5 µm, while PH‐POSS exhibited a preferential dispersion. Because of the possible homopolymerization of MA‐POSS during the melt blending, the glass transition temperature of polycarbonate (PC)/MA‐POSS composites remained nearly unchanged with respect to PC/PH‐POSS composites that showed a depression of T_g due to the plasticization effect. It is interesting to note that the incorporation of POSS retarded the degradation rates of PC composites and thus significantly improved the thermal stabilities. Si? O fractions left during POSS degradations were a key factor governing the formation of a gel network layer on the exterior surface. This layer possessed more compact structures, higher thermal stabilities, and some thermal insulation. In addition, percentage residues at 700°C (C₇₀₀) significantly increased from 10.8% to 15.8–22.1% in air. Fracture stress of two composites showed a slight improvement, and the impact strength of them decreased monotonically with the increase of POSS loading. Copyright © 2011 John Wiley & Sons, Ltd.     

Morphology,thermal stability,and flammability of polymer matrix composites coated with hybrid nanopapers

In this study, a hybrid nanopaper consisting of carbon nanofiber (CNF) and polyhedral oligomeric silsequioxane (POSS) or cloisite Na⁺ clay, has been fabricated through the papermaking process. The hybrid nanopaper was then coated on the surface of glass fiber (GF) reinforced polymer matrix composites through resin transfer molding (RTM) process. The morphologies of the hybrid nanopaper and resulting nanocomposites were characterized with scanning electron microscopy (SEM). It can be seen that the nanopaper had a porous structure with highly entangled carbon nanofibers and the polyester resin completely penetrated the nanopaper throughout the thickness. The thermal decomposition behavior of the hybrid nanopapers and nanocomposites was studied with the real‐time thermogravimetric analysis/ flourier transform infrared spectrometry (TGA/FTIR). The test results indicate that the addition of pristine nanoclay increased the thermal stability of the nanopaper, whereas the POSS particles decreased the thermal stability of the nanopaper. The fire retardant performance of composite laminates coated with the hybrid nanopaper was evaluated with cone calorimeter tests using a radiated heat flux of 50 kW/m². The cone calorimeter test results indicate that the peak heat release rate (PHRR) decreased dramatically in composite laminates coated with the CNF‐clay nanopaper. However, the PHRRs of the CNF‐POSS nanopaper coated composite laminates increased. The formation of compact char materials was observed on the surface of the residues of the CNF‐clay nanopaper after cone calorimeter test. The flame retardant mechanisms of the hybrid nanopaper in the composite laminates are discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetic model of poly(3-hydroxybutyrate) thermal degradation from experimental non-isothermal data

The non-isothermal data given by TG curves for poly(3-hydroxybutyrate) (PHB) were studied in order to obtain a consistent kinetic model that better represents the PHB thermal decomposition. Thus, data obtained from the dynamic TG curves were suitably managed in order to obtain the Arrhenius kinetic parameter E according to the isoconversional F-W-O method. Once the E parameters is found, a suitable logA and kinetic model (f(α)) could be calculated. Hence, the kinetic triplet (E±SD, logA±SD and f(α)) obtained for the thermal decomposition of PHB under non-isothermal conditions was E=152±4 kJ mol⁻¹, logA=14.1±0.2 s⁻¹ for the kinetic model, and the autocatalytic model function was: f(α)=α^m(1−α)ⁿ=α^0.42(1−α)^0.56.     

不同有机胺修饰MCM-41的CO2吸附性能和热稳定性

将乙二胺(EDA,60 g/mol)、四乙烯五胺(TEPA,189 g/mol)和两种聚乙烯亚胺600(PEI600g/mol; PEI1800g/mol)分别负载在MCM-41上制备氨基功能化介孔材料,研究其对CO₂的吸附性能和热稳定性.结果表明,除了EDA-MCM41,其他三种材料随着胺分子量增大CO₂吸附性能下降,但是热稳定性却有所提高,其中,TEPA-MCM41的吸附容量最大,达到2.7 mmol/g.同时发现,乙二胺在制备过程中随溶剂挥发而难以完全负载在MCM-41上.在纯N₂气氛和再生温度100 ℃条件下,经10次循环实验后,TEPA-MCM41的吸附能力下降了7.4%,而PEI600-MCM41和PEI1800-MCM41吸附能力保持不变,且质量变化在1%以内,表现出良好的再生稳定性.采用80%CO₂/20%N₂对吸附饱和的材料进行再生,四种材料的再生温度将提高到160 ℃以上,高分子量PEI600-MCM41和PEI1800-MCM41相比于TEPA-MCM41具有更好的热稳定性.     

The non-oxidative thermal degradation of poly (Di-2-chloroethyl itaconate)

The non-oxidative thermal degradation of poly (di-2-chloroethyl itaconate) (PD2CEI) was studied by TG and by analysing the thermal products. The major processes occurring during thermal analysis are crosslinking, depolymerisation and carbonisation. The thermal degradation activation energy increased with increasing sample mass loss. The thermal degradation of PD2CEI was compared to that of the structurally similar poly(2-chloroethyl methacrylate) (P2CMA).     

Synthesis, characterization and thermal properties of novel PMDA-PAPD/silica hybrid network polymers

Novel PMDA-PAPD/silica hybrid polymers were synthesized by the sol-gel process. Fourier transform infrared spectroscopy and ²⁹Si nuclear magnetic resonance spectroscopy were used to characterize the structure of the hybrids, (condensed siloxane bonds designated as Q¹, Q², Q³, Q⁴, wth 3-aminopropyltriethoxysilane having mono-, di-, tri-, tetra-substituted siloxane bonds is designated as T¹, T² and T³). The results revealed that Q³, Q⁴ and T³ are the major microstructure elements in forming a network structure. The surface morphology, particle size, crystallinity and the thermal stability of the hybrids were investigated using Scanning electron microscopy (SEM), Transmission Electron Microscopy (TEM), X-ray diffraction (XRD), Thermogravimetric analysis (TGA) and Differential Scanning Calorimetry (DSC). SEM and TEM revealed that the hybrids were nanocomposites. The XRD indicated that covalent bonding (Si-O-Si) between the organic and inorganic components enhanced miscibility. DSC and TGA results showed that these hybrid materials had excellent thermal stability. The heat capacities of some materials were reported for the temperature range 273 K and 363 K as no thermal anomaly was found in this temperature range.     

The influence of melamine phosphate modified MoS2 on the thermal and flammability of poly(butylene succinate) composites

This work reported a facile fabrication method to modify molybdenum disulfide (MoS₂) nanosheets with common flame retardant melamine phosphate (MAP) and then were incorporated into poly(butylene succinate) by melt blending method with the purpose of improving the thermal and flame retardancy properties. MAP modified MoS₂ nanosheets dispersed well in poly(butylene succinate) composites with intercalated structure. The incorporation of MAP modified MoS₂ nanosheets led to an increase of thermal degradation temperature and char formation as well as reduction of the peak heat release rate. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of processing conditions on rheological,thermal, and electrical properties of multiwall carbon nanotube/epoxy resin composites

We report on the effect of processing conditions on rheology, thermal and electrical properties of nanocomposites containing 0.02–0.3 wt % multiwall carbon nanotubes in an epoxy resin. The influence of the sonication, the surface functionalization during mixing, as well as the application of external magnetic field (EMF) throughout the curing process was examined. Rheological tests combined with optical microscopy visualization are proved as a very useful methodology to determine the optimal processing conditions for the preparation of the nanocomposites. The Raman spectra provide evidence for more pronounced effect on the functionalized with hardener compositions, particularly by curing upon application of EMF. Different chain morphology of CNTs is created depending of the preparation conditions, which induced different effects on the thermal and electrical properties of the nanocomposites. The thermal degradation peak is significantly shifted towards higher temperatures by increasing the nanotube content, this confirming that even the small amount of carbon nanotubes produces a strong barrier effect for the volatile products during the degradation. The ac conductivity measurements revealed lower values of the percolation threshold (pc) in the range of 0.03–0.05 wt %. CNTs for the nanocomposites produced by preliminary dispersing of nanotubes in the epoxy resin, compared to those prepared by preliminary functionalization of the nanotubes in the amine hardener. This is attributed to the higher viscosity and stronger interfacial interactions of the amine hardener/CNT dispersion which restricts the reorganization of the nanotubes. The application of the EMF does not influence the pc value but the dc conductivity values (σ_dc) of the nanocomposites increased at about one order of magnitude due to the development of the aforementioned chain structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011