Organically nanoporous silica gel based on carbon paste electrode for potentiometric detection of trace Cr(III)

A new ion-selective electrode (ISE) for the detection of trace chromium(III) was designed by using 2-acetylpyridine and nanoporous silica gel (APNSG)-functionalized carbon paste electrode (CPE). The presence of APNSG acted as not only a paste binder, but also a reactive material. With 7.5 wt% APNSG proportions, the developed electrode exhibited wide dynamic range of 1.0 × 10⁻⁸ to 1.0 × 10⁻³ M toward Cr(III) with a detection limit of 8.0 × 10⁻⁹ M and a Nernstian slope of 19.8 ± 0.2 mV decade⁻¹. The as-prepared electrode displayed rapid response (∼55 s), long-time stability, and high sensitivity. Moreover, the potentiometric responses could be carried out with wide pH range of 1.5-5.0. In addition, the content of Cr(III) in food samples, e.g. coffee and tea leaves, has been assayed by the developed electrode, atomic absorption spectrophotometer (AAS) and atomic emission spectrometer (ICP-AES), respectively, and consistent results were obtained. Importantly, the response mechanism of the proposed electrode was investigated by using AC impedance and UV-vis spectroscopy.     

Carbon nanotube-based ion imprinted polymer as electrochemical sensor and sorbent for Zn(II) ion from paint industry wastewater

A novel technique was presented to embed Zn(II) ion imprinted and nonimprinted polymers using various approaches for its sensing and sorption. Ion imprinted and nonimprinted polymers were fabricated by layering on MWCNTs or by bulk imprinting and characterized. Here Zn(II) ion was template, acrylic acid as monomer and N,N-methylene-bis-acrylamide as crosslinker. The electrochemical performance of electrode modified with imprinted and nonimprinted polymers were scrutinized and optimized with cyclic voltammetry (CV). The limit of detection for Zn(II) ion was found to be 1.32?×?10^?4?µM by differential pulse voltammetry (DPV). The applicability of the system was checked with paint industry wastewater.     

Multiwalled carbon nanotube based ion imprinted polymer as sensor and sorbent for environmental hazardous cobalt ion

By using molecular imprinting approach, a highly selective multiwalled carbon nanotube based electrochemical sensor for Co(II) ion was fabricated. The sites for binding of Co(II) ion was created with cobalt ion as template, NNMBA-crosslinked polyacrylic acid as the solid polymer matrix which is coated on functionalized MWCNTs. For the comparison, system without template was also created (MWCNT-NIP). In order to check the importance of MWCNTs, imprinted (IIP) and non-imprinted (NIP) polymer without MWCNTs were also produced. The developed systems were successfully characterized by different analytical techniques. The selectivity of the systems was checked with different metal ions. The electrochemical response of the nanostructures modified platinum electrode were investigated and optimized. The MWCNT-IIP/Co/PE exhibit fast sensing and high selectivity towards Co(II) ion. The detection limit of the sensor was explored with differential pulse voltammetry and it was found to be at 1.01 × 10^?5µM. The practical applicability of the sensor was successfully applied for the trace sensing and extraction of Co(II) ion from real samples such as fertilizer and battery. The recoveries of Co(II) ion from the samples were very high, that revealed the efficiency of the systems for environmental applications.     

Development of a Cr(III)-specific potentiometric sensor using Aurin tricarboxylic acid modified silica

A new chelating resin, Aurin tricarboxylic acid modified silica, was synthesized. The resin behaves as a selective chelating ion exchanger for Cr(III) at a pH 3.8-5.5. A polyvinyl chloride-based membrane electrode of the modified silica has been fabricated and explored as sensor for Cr(III) ions. The membrane works well over the concentration range 7.0 × 10⁻⁶ to 1 × 10⁻¹ M of Cr(III) with a Nernstian slope of 19.0 mV per decade of concentration. The response time of the sensor is 10 s and it can be used for a period of 5 months. The performance of the sensor is best in the pH range 3.5-6.5 and it also works well in partially non-aqueous medium. The selectivity coefficient values depicts that the membrane exhibits good selectivity over a number of interfering ions. Moreover, the membrane sensor has been applied to analyse the concentration of chromium in certified steel sample and food materials with greater than 97% accuracy.     

A new potentiometric sensor based on a high-performance composite for nanomolar determination of mercury (II) in environmental samples

A new potentiometric sensor for the rapid determination of Hg²⁺ based on modified carbon paste electrode consisting of room temperature ionic liquid, 1-Butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆), multi-walled carbon nanotubes (MWCNTs), alumina nanoparticles and a synthetic macrocyclic diamide ‘7,10,13-triaza-1-thia-4,16-dioxa-6,14-dioxo-2,3;17,18-dinaphtho-cyclooctadecane’ as an efficient ionophore was constructed. Prepared composite is an ideal paste because it has low drift of potential, high selectivity and fast response time (10 s), which leads to a more stable potential signal. The morphology and properties of electrodes surface were characterised by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy. A linear dynamic range of 2.01–2.01 × 10⁷ µg L^?1 with detection limit of 1.40 µg L^?1 Hg²⁺ was obtained at pH range of 2.5 to 4.5. The prepared modified electrode shows several advantages such as simple preparation method, high stability of the composite paste, high sensitivity, long-term life time (at least 13 weeks) and remarkable potentiometric reproducibility. The modified electrode was successfully applied for the accurate determination of trace amounts of Hg ²⁺ in environmental samples.     

Studies on the potentiometric thallium(III)-selective carbon paste electrode and its possible applications

Construction, performance characteristics and applications of a carbon paste thallium(III) ion-selective electrode are described. The electrode, which is based on ion-associate compounds formed between cetylpyridinium and chlorothallate(III) complexes dissolved in tricresyl phosphate as pasting liquid, showed near-Nernstian response over the concentration range of 5.8 x 10(-6) - 2.9 x 10(-3) mol/L. Potentiometric titrations of thallium(III) with cetylpyridinium chloride were affected by higher concentrations of excess halides, probably due to the formation of higher halogenothallates.     

Studies on the potentiometric thallium(III)-selective carbon paste electrode and its possible applications

Construction, performance characteristics and applications of a carbon paste thallium(III) ion-selective electrode are described. The electrode, which is based on ion-associate compounds formed between cetylpyridinium and chlorothallate(III) complexes dissolved in tricresyl phosphate as pasting liquid, showed near-Nernstian response over the concentration range of 5.8 × 10^–6– 2.9 × 10^–3 mol/L. Potentiometric titrations of thallium(III) with cetylpyridinium chloride were affected by higher concentrations of excess halides, probably due to the formation of higher halogenothallates.     

Calcium(II)-selective potentiometric sensor based on p -isopropylcalix6arene in PVC matrix

In Japan, large amounts of fertilizer nitrogen are applied to tea plantations. We collected samples of tea plantation soil each season for a year. Samples were analyzed for their contents of various inorganic chemicals and total N. Nitrogen was present mainly in the top 0 to 30?cm of soil. However, at times the concentration of nitrate N in the soil water was more than 35?mg?L^?1, even in the deepest layers. The contents of various metal elements in the soil were examined. Ba, Fe, Sr and Zn contents were high in the top 0 to 30?cm of soil. But Al and Mn contents were not always high in the top 0 to 30?cm of soil. From the correlation analysis among contents of various inorganic chemicals, it was suggested that increased leaching of Al, Mn, and Zn from tea plantation soil occurred with increased nitrate N concentration.     

Novel potentiometric sensor for the determination of Cd2+ based on a new nano-composite

A novel ion selective carbon paste electrode for Cd²⁺ ions based on 2,2′-thio-bis[4-methyl(2-amino phenoxy) phenyl ether] (TBMAPPE) as an ionophore was prepared. The carbon paste was made based on a new nano-composite including multi-walled carbon nanotubes (MWCNTs), nanosilica and room-temperature ionic liquid, 1-Butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆). The constructed nano-composite electrode showed better sensitivity, selectivity, response time, response stability and lifetime in comparison with typical Cd²⁺ carbon paste sensor for the successful determination of Cd²⁺ ions in water and in waste water samples. The best performance for nano-composite sensor was obtained with an electrode composition of 18% TBMAPPE, 20% BMIM-PF₆, 48% graphite powder, 10% MWCNT and 4% nanosilica. The new electrode exhibited a Nernstian response (29.95?±?0.10?mV?decade^?1) toward Cd²⁺ ions in the range of 3.0?×?10^?8 to 1.0?×?10^?1?mol?L^?1 with a detection limit of 7.5?×?10^?9?mol?L^?1. The potentiometric response of prepared sensor was independent of the pH of test solution in the pH range 3.0 to 5.5. It had a quick response with a response time of about 6?s. The proposed electrode showed fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions.     

Tetrachloroferrate(III)-selective liquid membrane electrode based on crystal violet

An extract of crystal violet-tetrachloroferrate(III) in nitrobenzene was used to prepare a tetrachloroferrate(III)-selective liquid membrane electrode with a poly(vinyl chloride) support. The optimal conditions to determine 2.5 × 10^–5 – 5.0 × 10^–2 M iron(III) as tetrachloroferrate(III) (anionic slope 56 mV/decade, detection limit 7.9 × 10^–6 M) were found to be 4.0–5.5.M total chloride in 0.75–1.5M hydrochloric acid. The electrode was reliably applied to determine iron in human blood, haematite and mineralized vitamin syrup by direct potentiometry, standard and sample additions as well as standard subtraction techniques.     

Graphite disk Lanthanum(III)-selective electrode based on Kryptofix-22DD

ABSTRACT

A novel ion-selective electrochemical sensor based on kryptofix-22DD (1,10-didecyl-1,10-diaza-18-crown-6) as an ionophore was constructed for determination of lanthanum(III) cation in solutions. The D-Optimal Mixture Design(D-OMD) was used as an experimental design strategy for optimal formulation of the membrane ingredients, and the actual values of the ingredients were compared with their predicted values. The amounts of the ionophore, plasticizer, PVC, and also the graphite powder which influence the performance of the fabricated electrode were analyzed using D-OMD. A non-linear relationship was observed between the slope of the electrochemical response of the electrode and these variables and the interaction between the variables as well. The experimental results showed that the amount of the ionophore has the most positive effect on the electrochemical response of the electrode. The constructed electrode exhibits a Nernstian slope (20.60 ± 0.21 mv.decade^?1) in a wide linear concentration range from 1.0 × 10^?7 to 1.0 × 10^?1 M with respect to La³⁺ cation at pH range of 4.0 to 6.0, and its detection limit was found to be:0.8 × 10^?7M. The selectivity of the proposed electrode towards some of the metal cations present in lanthanum(III) cation solutions was tested, and the experimental results showed a good selectivity towards this metal cation.     

用羟基磷灰石和单壁碳纳米管制备葡萄糖传感器的研究

在滴涂法制得单壁碳纳米管(SWNTs)修饰电极的基础上,采用电化学方法沉积纳米羟基磷灰石(HA)涂层,进而利用分子组装技术将葡萄糖氧化酶(GOD)固定到该电极上,制得的修饰电极的循环伏安测量结果表明,GOD发生了直接的电子传递.GOD-HA-SWNTs/GC修饰电极对不同浓度的葡萄糖呈现两个良好的线性响应范围,有望开发...     

Chromium(III) ion selective electrode based on glyoxal bis(2-hydroxyanil)

A poly(vinyl chloride) membrane based on glyoxal bis(2-hydroxyanil) as membrane carrier was prepared and investigated as a Cr(III)-selective electrode. The electrode has a linear dynamic range of 3.0×10⁻⁶-1.0×10⁻² mol l⁻¹, with a Nernstian slope of 19.8±0.5 mV per decade and a detection limit of 6.3×10⁻⁷ mol l⁻¹. It has a fast response time of <20 s and can be used for at least 3 months without any considerable divergence in potential. The proposed electrode revealed good sensitivities for Cr(III) over a wide variety of metal ions and could be used in a pH range of 2.7-6.5. Above all, the membrane sensor has been used very successfully for the analysis of some food materials and alloys for the determination of Cr(III) ion.     

A novel cobalt(II)-selective potentiometric sensor based on p-(4-n-butylphenylazo)calix[4]arene

A new poly(vinyl chloride)-based membranes containing p-(4-n-butylphenylazo)calix[4]arene (I) as an electroactive material along with sodiumtetraphenylborate (NaTPB), and dibutyl(butyl)phosphonate in the ratio 10:100:1:200 (I:DBBP:NaTPB:PVC) (w/w) was used to fabricate a new cobalt(II)-selective sensor. It exhibited a working concentration range of 9.2 × 10⁻⁶ to 1.0 × 10⁻¹ M, with a Nernstian slope of 29.0 ± 1.0 mV/decade of activity and the response time of 25 s. This sensor shows the detection limit of 4.0 × 10⁻⁶ M. Its potential response remains unaffected of pH in the range, 4.0-7.2, and the cell assembly can be used successfully in partially non-aqueous medium (up to 10%, v/v) without significant change in the slope of working concentration range. The sensor has a lifetime of about 3 months and exhibits excellent selectivity over a number of mono-, bi-, and tri-valent cations including alkali, alkaline earth metal, heavy and transition metal ions. It can be used as an indicator electrode for the end point determination in the potentiometric titration of cobalt ions against ethylenediaminetetraacetic acid (EDTA) as well as for the determination of cobalt ion concentration in real samples.     

Aluminum(III) selective potentiometric sensor based on morin in poly(vinyl chloride) matrix

Al³⁺ selective sensor has been fabricated from poly(vinyl chloride) (PVC) matrix membranes containing neutral carrier morin as ionophore. Best performance was exhibited by the membrane having composition as morin:PVC:sodium tetraphenyl borate:tri-n-butylphosphate in the ratio 5:150:5:150 (w/w, mg). This membrane worked well over a wide activity range of 5.0 × 10⁻⁷ to 1.0 × 10⁻¹ M of Al³⁺ with a Nernstian slope of 19.7 ± 0.1 mV/decade of Al³⁺ activity and a limit of detection 3.2 × 10⁻⁷ M. The response time of the sensor is ∼5 s and membrane could be used over a period of 2 months with good reproducibility. The proposed sensor works well over a pH range (3.5-5.0) and demonstrates good discriminating power over a number of mono-, di- and trivalent cations. The sensor can also be used in partially non-aqueous media having up to 20% (v/v) methanol, ethanol or acetone content with no significant change in the value of slope or working activity range. The sensor has also been used in the potentiometric titration of Al³⁺ with EDTA and for its determination in zinc plating mud and red mud.     

Third generation biosensor based on myoglobin-TiO2/MWCNTs modified glassy carbon electrode

TiO2 nanoparticles were homogeneously coated on multi-walled carbon nanotubes by hydrothermal deposition, this nanocomposite may be a promising material for myoglobin immobilization in view of its high biocompatibility and large surface. The glassy carbon electrode modified with Mb-TiO2/MWCNTs films exhibited a pair of weU defined, stable and nearly reversible cycle voltammetric peaks. The electron transfer between Mb and electrode surface, Ks of 3.08 s^-1, was greatly facilitated in the TiO2/ MWCNTs film. The electrocatalytic reductions of hydrogen peroxide were studied, the apparent Michaelis-Menten constant is calculated to be 83.10 μmol/L, which shows a large catalytic activity of Mb in the TiO2/MWCNTs film to H2O2.     

Enzyme-free ethanol sensor based on electrospun nickel nanoparticle-loaded carbon fiber paste electrode

We have developed a novel nickel nanoparticle-loaded carbon fiber paste (NiCFP) electrode for enzyme-free determination of ethanol. An electrospinning technique was used to prepare the NiCF composite with large amounts of spherical nanoparticles firmly embedded in carbon fibers (CF). In application to electroanalysis of ethanol, the NiCFP electrode exhibited high amperometric response and good operational stability. The calibration curve was linear up to 87.5 mM with a detection limit of 0.25 mM, which is superior to that obtained with other transition metal based electrodes. For detection of ethanol present in liquor samples, the values obtained with the NiCFP electrode were in agreement with the ones declared on the label. The attractive analytical performance and simple preparation method make this novel material promising for the development of effective enzyme-free sensors.     

Comparative studies on Tb (III)-selective PVC membrane sensors

A new terbium selective sensor based on N-(2-hydroxyphenyl)-3-(2-hydroxyphenylhydroxyphenylimino)-N-phenylbutanamidine (L₁) and N,N′-bis((1H-indole-3-yl)methylene)butane-1,4 diamine (L₂) as a ionophore is reported. Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), dibutyl butylphosphonate (DBBP), chloronaphthelene (CN), dioctylphthalate (DOP) and tri-(2-ethylhexyl)phosphate (TEHP) with anion excluder, potassium tetrakis (p-chloropheny1)borate (KTpClPB) have been studied. The membrane with a composition of ionophore (L₁):KTpClPB:PVC:o-NPOE (w/w, %) in ratio of 3.0:5.0:30.0:62.0 exhibited enhanced selectivity towards terbium ions (III) in the concentration range of 3.5 × 10⁻⁷ to 1.0 × 10⁻² M with a detection limit of 1.2 × 10⁻⁷ M and a Nernstian slope (20.0 ± 0.5 mV dec⁻¹ activity). The sensors showed the working pH range to be 3.5-7.5 with response time of 11 s. The sensor has been found to work satisfactorily in partially non-aqueous media up to 15% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients indicated high selectivity for terbium (III). The fast and stable response, good reproducibility and long-term stability of the sensors were observed. The application of the sensor has been demonstrated in determination of terbium (III) ions in spiked water samples.     

Copper nanoparticles entrapped in SWCNT-PPy nanocomposite on Pt electrode as NOx electrochemical sensor

A highly sensitive NO_x sensor was designed and developed by electrochemical incorporation of copper nanoparticles (CuNP) on single-walled carbon nanotubes (SWCNT)-polypyrrole (PPy) nanocomposite modified Pt electrode. The modified electrodes were characterized by scanning electron microscopy and energy dispersive X-ray analysis. Further, the electrochemical behavior of the CuNP-SWCNT-PPy-Pt electrode was investigated by cyclic voltammetry. It exhibited the characteristic CuNP reversible redox peaks at −0.15 V and −0.3 V vs. Ag/AgCl respectively. The electrocatalytic activity of the CuNP-SWCNT-PPy-Pt electrode towards NO_x is four-fold than the CuNP-PPy-Pt electrode. These results clearly revealed that the SWCNT-PPy nanocomposite facilitated the electron transfer from CuNP to Pt electrode and provided an electrochemical approach for the determination of NO_x. A linear dependence (r² = 0.9946) on the NO_x concentrations ranging from 0.7 to 2000 μM, with a sensitivity of 0.22 ± 0.002 μA μM⁻¹ cm⁻² and detection limit of 0.7 μM was observed for the CuNP-SWCNT-PPy-Pt electrode. In addition, the sensor exhibited good reproducibility and retained stability over a period of one month.