Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

Flow injection potentiometry by a new coated graphite ion-selective electrode for the determination of Pb(2+)

A new graphite coated electrode for the determination of Pb²⁺ based on a recently synthesized ionophore 1-hydroxy-2-{2-[2-(2-hydroxy-ethoxy)-ethoxy]-ethoxy methyl}-anthracene-9,10-dione (L) has been developed. The electrode was used in flow injection potentiometry by a home-made flow cell. Under both the batch and flow conditions, the electrode revealed a near Nernstian response over a wide lead ion concentration range (10⁻⁶ to 10⁻¹ M) and very low limit of detection. In flow injection potentiometry, excellent reproducibility (RSD%=0.49%), very high sampling rate (170 injections h⁻¹) and stable baseline was observed in the presence of 10⁻³ M KCl as ionic strength adjuster. The electrode showed high sensitivity and good selectivity for Pb²⁺ over a wide variety of alkali, alkali earth and transition metal ions and the electrode can be used for at least 3 months without any considerable change in potential response. The proposed sensor was successfully applied to the direct determination of lead in real samples and also used for the titrimetric determination of phosphate ions by both batch and flow injection potentiometry.     

Highly selective and sensitive monohydrogen phosphate membrane sensor based on molybdenum acetylacetonate

In this work, a highly selective and sensitive monohydrogen phosphate membrane sensor based on a molybdenum bis(2-hydroxyanil) acetylacetonate complex (MAA) is reported. The sensor shows a linear dynamic range between 1.0 × 10⁻¹ and 1.0 × 10⁻⁷ M, with a nice Nernstian behavior (−29.5 ± 0.3 mV decade⁻¹) in pH of 8.2. The detection limit of the electrode is 6.0 × 10⁻⁸ M (∼6 ppb). The best performance was obtained with a membrane composition of 32% poly(vinyl chloride), 58% benzyl acetate, 2% hexadecyltrimethylammonium bromide and 8% MAA. The sensor possesses the advantages of short response time, low detection limit and especially, very good selectivity towards a large number of organic and inorganic anions including salicylate, citrate, tartarate, acetate, oxalate, fluoride, chloride, bromide, iodide, sulfite, sulfate, nitrate, nitrite, cyanide, thiocyanate, perchlorate, metavanadate, and bicarbonate ions. The electrode can be used for at least 10 weeks without any considerable divergence in its slope and detection limit. It was used as an indicator electrode in potentiometric titration of monohydrogenphosphate ion with barium chloride. The proposed sensor was successfully applied to direct determination of monohydrogenphosphate in two fertilizer samples (NPK).     

Novel potentiometric membrane sensor based on 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene for detection of strontium (II) ions at trace levels

A new PVC membrane strontium ion-selective electrode has been constructed using 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene (NPDBH) as a neutral ionophore. The electrode was prepared with 7% NPDBH (as ionophore), 57% acetophenone (as plasticizer), 30% PVC and 6% oleic acid (as lipophilic additive). The electrode responds to Sr²⁺ ion with a sensitivity of 28.2 ± 0.5 mV/decade over the range 1.0 × 10⁻⁶-1.0 × 10⁻¹ mol L⁻¹ and in a pH range of 3.0-10.0. The limit of detection was 2.4 × 10⁻⁷ mol L⁻¹. It has a response time of <20 s and can be used for at least three months without any divergence in potentials. The proposed electrode shows good discrimination of Sr²⁺ ion from several cations. The effect of organic solvents on electrode response was examined. The results show that this electrode can be used in ethanol media up to 15% (v/v) concentration without interference. The isothermal temperature coefficient of this electrode amounted to 0.00019 V/°C. The electrode was found to work well under laboratory conditions. It was successfully applied to the determination of strontium ions in human urine and bone digests.     

An ultra-sensitive and colorimetric sensor for copper and iron based on glutathione-functionalized gold nanoclusters

Here, we report an ultra-sensitive and colorimetric sensor for the detection of Fe³⁺ or Cu²⁺ successively using glutathione-functionalized Au nanoclusters (GSH-AuNCs). For GSH-AuNCs can catalytically oxidize peroxidase substrates, such as 3, 3′, 5, 5′-tetramethylbenzidine (TMB), colored products are formed in the presence of H₂O₂. While upon the addition of Fe³⁺ or Cu²⁺ into the GSH-AuNCs-TMB-H₂O₂ system, diverse color and absorbance of the system was obtained due to the self oxidation of Fe³⁺ and the inhibition of peroxidase-like activity of GSH-AuNCs. With the introduction of ethylene diamine tetraacetic acid (EDTA) or ammonium fluoride (NH₄F) to GSH-AuNCs-TMB-H₂O₂+Cu²⁺ system or GSH-AuNCs-TMB-H₂O₂+Fe³⁺ system respectively, a restoration of color and absorbance of system was realized. On the basis of above phenomenon, a colorimetric and quantitative approach for detecting Fe³⁺ and Cu²⁺ was developed with detection limit of 1.25 × 10⁻⁹ M and 1.25 × 10⁻¹⁰ M respectively. Moreover, the concentration of Fe³⁺ and Cu²⁺ in human serums was also accurate quantified by this method. So this design strategy realized the simple and simultaneous detection of Fe³⁺ and Cu²⁺, suggesting significant potential in clinical diagnosis.     

Novel potentiometric sensor for the trace-level determination of Zn2+ based on a new nanographene/ion imprinted polymer composite

In this research, a new strategy for construction of a development potentiometric carbon paste Zn²⁺-ion selective electrode based on a novel nano-sensing layer is suggested. The proposed nano-sensing layer was prepared with the addition of a synthesised Zn²⁺-ion imprinted polymer nanoparticles ‘as an efficient sensing agent’ into the carbon paste matrix consisting of graphite powder, nanographene-composite ‘graphene nanosheets decorated with silver nanoparticles’ and 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ‘ an ionic liquid ’, as the conducting binder. Under the optimised experimental conditions, the suggested nanographene-composite potentiometric sensor presented a low detection limit of 1.93 × 10^?1 μg L^?1 and a linear analytical range from 2.62 × 10^?1 to 6.54 × 10⁵ μg L^?1 with an excellent Nernstian slope of 29.80 mV decade^?1. The proposed zinc selective sensor was successfully applied for the highly sensitive determination of trace amounts of Zn²⁺ in environmental and biological samples with satisfactory results.     

Construction of a new Cu2+ coated wire ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylidene amino)phenyl)disufanyl)phenylimino)methyl)-4-methoxyphenol Schiff base

In this article a new coated platinum Cu²⁺ ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylideneamino)phenyl)disufanyl)phenylimino) methyl)-4-methoxyphenol Schiff base (L₁) as a new ionophore is described. This sensor has a wide linear range of concentration (1.2 × 10⁻⁷-1.0 × 10⁻¹ mol L⁻¹) and a low detection limit of 9.8 × 10⁻⁸ mol L⁻¹of Cu(NO₃)₂. It has a Nernstian response with slope of 29.54 ± 1.62 mV decade⁻¹ and it is applicable in the pH range of 4.0-6.0 without any divergence in potentioal. The coated electrode has a short response time of approximately 9 s and is stable at least for 3.5 months. The electrode shows a good selectivity for Cu²⁺ ion toward a wide variety of metal ions. The proposed sensor was successfully applied for the determination of Cu²⁺ ion in different real and environmental samples and as indicator electrode for potentiometric titration of Cu²⁺ ion with EDTA.     

An optical chemical sensor for mercury ion based on 2-mercaptopyrimidine in PVC membrane

An optical chemical sensor based on 2-mercaptopyrimidine (2-MP) in plasticized poly(vinyl chloride) (PVC) membrane incorporating (N,N-diethyl-5-(octadecanoylimino)-5H benzo[a]phenoxazine-9-amine (ETH 5294) and sodium tetraphenyl borate (NaTPB) for batch and flow-through determination of mercury ion is described. The response of the sensor is based on selective complexation of Hg²⁺ with 2-MP in the membrane phase, resulting in an ion exchange process between H⁺ in the membrane and Hg²⁺ in the sample solution. The influences of several experimental parameters, such as membrane composition, pH, and type and concentration of the regenerating reagent, were investigated. The sensor has a response range of 2.0 × 10⁻⁹ to 2.0 × 10⁻⁵ mol L⁻¹ Hg²⁺ with a detection limit of 4.0 × 10⁻¹⁰ mol L⁻¹ and a response time of ≤45 s at optimum pH of 6.5 with high measurement repeatability and sensor-to-sensor reproducibility. It shows high selectivity for Hg²⁺ over several transition metal ions, including Ag⁺, Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, and common alkali and alkaline earth ions such as Na⁺, K⁺, Mg²⁺, Ca²⁺, and Pb²⁺. The sensor membrane can be easily regenerated with dilute acid solutions. The sensor has been used for the determination of mercury ion concentration in water samples.     

An efficient and selective flourescent chemical sensor based on 5-(8-hydroxy-2-quinolinylmethyl)-2,8-dithia-5-aza-2,6-pyridinophane as a new fluoroionophore for determination of iron(III) ions. A novel probe for iron speciation

A novel fluorescent chemical sensor for the highly sensitive and selective determination of Fe³⁺ ions in aqueous solutions is prepared. The iron sensing system was prepared by incorporating 5-(8-hydroxy-2-quinolinylmethyl)-2,8-dithia-5-aza-2,6-pyridinophane (L) as a neutral Fe³⁺-selective fluoroionophore in the plasticized PVC membrane containing sodium tetraphenylborate as a liphophilic anionic additive. The response of the sensor is based on the strong fluorescence quenching of L by Fe³⁺ ions. At pH 5.5, the proposed sensor displays a calibration curve over a wide concentration range from 6.0 × 10⁻⁴ to 1.0 × 10⁻⁷ M, with a relatively fast response time of less than 2 min. In addition to a high stability and reproducibility, the sensor shows a unique selectivity toward Fe³⁺ ion with respect to common coexisting cations. The proposed fluorescence optode was applied to the determination of iron(III) content of straw of rice, spinach and different water samples. The fluorescent sensor was also used as a novel probe for Fe³⁺/Fe²⁺ speciation in aqueous solution.     

Cobalt(II)-selective membrane sensor based on a [Me2(13)dieneN4] macrocyclic cobalt complex

A new poly(vinyl chloride)-based membrane was fabricated with the cobalt(II) complex of 2,4-dimethyl-1,5,8,11-tetraazacyclotrideca-1,4-diene [Me₂(13)dieneN₄] as an ion carrier. The membrane composition was Co²⁺ complex/PVC/NaTPB/DBP 15:50:15:20 (w/w). The sensor exhibited a Nernstian response for Co²⁺ ions over a wide concentration range (7.94×10⁻⁶–1.0×10⁻¹ M) at pH 2.5–7.0, a response time of 10 s, and it could be used for 3 months without any significant divergence in potential. The proposed membrane sensor exhibited good selectivity for Co²⁺ over a wide variety of other metal ions and in mixtures containing up to 25% (v/v) non-aqueous content. The sensor was successfully used as an indicator electrode in the potentiometric titration of Co²⁺ with EDTA and the direct determination of Co²⁺ in real samples.     

A coumarinylaldoxime as a specific sensor for Cu and its biological application

In this Letter we present a new probe, (E)-7-(diethylamino)-2-oxo-2H-chromene-3-carbaldehyde oxime (JB), which can detect Cu²⁺ ions in HEPES buffer under physiological conditions. Benesi–Hildebrand and Job plots demonstrate that the stoichiometry of the Cu²⁺ complex formed is 2:1. Possible interference with other analytes was examined, and the decrease of the fluorescence of JB at 510 nm when it reacts with Cu²⁺ was shown to be highly selective. This probe accumulates in the plasmalemma of human neuroblastoma SH-SY5Y cells. Molecular dynamics (MD) simulations revealed that JB interacts with the lipid bilayer at the level of the glycerol moieties.     

Enantioselective, potentiometric membrane electrodes based on cyclodextrins: application for the determination of R-baclofen in its pharmaceutical formulation

Two enantioselective, potentiometric membrane electrodes based on α- and γ-cyclodextrins were proposed for the assay of R-baclofen. The slopes of the electrodes were 59.50 and 51.00 mV/pR-baclofen for α- and γ-cyclodextrin-based electrodes, respectively. The detection limits of the proposed electrodes were 7 × 10⁻⁹ mol l⁻¹ for α-cyclodextrin-based electrode and 1.44 × 10⁻¹⁰ mol l⁻¹ for γ-cyclodextrin-based electrode. The enantioselectivity was determined over S-baclofen. The proposed electrodes can be employed for the assay of R-baclofen raw materials and its pharmaceutical formulation, Norton-Baclofen^® tablets. The surfaces of the electrodes are stable and easily renewable by polishing on alumina paper.     

Recent advances of adsorbents in solid phase extraction for environmental samples

In recent years, some new and sensitive analytical instruments have been invented or existing instruments have been improved, which have resulted in many advanced achievements. However, sample pre-treatment techniques still play important and irreplaceable roles in the analysis of pollutants. Among the developed sample pre-treatment techniques, solid phase extraction is the most often used method and has been widely applied worldwide. In solid phase extraction, adsorbent is the key part to achieve high sensitivity and enrichment efficiency, which is the hot topic in analytical and environmental fields in recent years. In order to deeply understand the prospect of solid phase extraction, this review summarises the recent advances of adsorbents including ion imprinting materials, magnetic materials, core-shell materials, mesoporous materials, carbon nanotubes, TiO₂ nanotube arrays and some other new materials.     

Silver ion imprinted polymer nanobeads based on a aza-thioether crown containing a 1,10-phenanthroline subunit for solid phase extraction and for voltammetric and potentiometric silver sensors

A new nano-sized silver(I) ion-imprinted polymer (IIP) was prepared via precipitation copolymerization using ethyleneglycol dimethacrylate, as a cross-linking agent in the presence of Ag⁺ and an aza-thioether crown containing a 1,10-phenanthroline subunit as a highly selective complexing agent. The imprint silver(I) ion was removed from the polymeric matrix using a 1.0 M HNO₃ solution. The resulting powder material was characterized using IR spectroscopy and scanning electron microscopy. The SEM micrographs showed colloidal nanoparticles of about 52 nm and 75 nm in diameter and slightly irregular in shape for leached and unleached IIPs, respectively. The optimal pH for quantitative enrichment was 6.0 and maximum sorbent capacity of the prepared IIP for Ag⁺ was 18.08 μmol g⁻¹. The relative standard deviation and limit of detection (LOD = 3S_b/m) for flame atomic absorption spectrometric determination of silver(I) ion, after its selective extraction by the prepared IIP nanobeads, were evaluated as 2.42% and 2.2 × 10⁻⁸ M, respectively. The new Ag⁺-IIP was also applied as a suitable sensing element to the preparation of highly selective and sensitive voltammetric and potentiometric sensors for ultra trace detection of silver(I) ion in water samples, with limits of detection of 9.0 × 10⁻¹⁰ and 1.2 × 10⁻⁹ M, respectively.     

Fabrication and application of a new modified electrochemical sensor using nano-silica and a newly synthesized Schiff base for simultaneous determination of Cd,Cu and Hg ions in water and some foodstuff samples

A new chemically modified carbon paste electrode was constructed and used for rapid, simple, accurate, selective and highly sensitive simultaneous determination of cadmium, copper and mercury using square wave anodic stripping voltammetry (SWASV). The carbon paste electrode was modified by N,N′-bis(3-(2-thenylidenimino)propyl)piperazine coated silica nanoparticles. Compared with carbon paste electrode, the stripping peak currents had a significant increase at the modified electrode. Under the optimized conditions (deposition potential, −1.100 V vs. Ag/AgCl; deposition time, 60 s; resting time, 10 s; SW frequency, 25 Hz; pulse amplitude, 0.15 V; dc voltage step height, 4.4 mV), the detection limit was 0.3, 0.1 and 0.05 ng mL⁻¹ for the determination of Cd²⁺, Cu²⁺ and Hg²⁺, respectively. The complexation reaction of the ligand with several metal cations in methanol was studied and the stability constants of the complexes were obtained. The effects of different cations and anions on the simultaneous determination of metal ions were studied and it was found that the electrode is highly selective for the simultaneous determination of Cd²⁺, Cu²⁺ and Hg²⁺. Furthermore, the present method was applied to the determination of Cd²⁺, Cu²⁺ and Hg²⁺ in water and some foodstuff samples.     

Solid-state electrochemiluminescence sensor based on the Nafion/poly(sodium 4-styrene sulfonate) composite film

An effective electrochemiluminescence (ECL) sensor based on Nafion/poly(sodium 4-styrene sulfonate) (PSS) composite film-modified ITO electrode was developed. The Nafion/PSS/Ru composite film was characterized by atomic force microscopy, UV-vis absorbance spectroscopy and electrochemical experiments. The Nafion/PSS composite film could effectively immobilize tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) via ion-exchange and electrostatic interaction. The ECL behavior of Ru(bpy)₃²⁺ immobilized in Nafion/PSS composite film was investigated using tripropylamine (TPA) as an analyte. The detection limit (S/N = 3) for TPA at the Nafion/PSS/Ru composite-modified electrode was estimated to be 3.0 nM, which is 3 orders of magnitude lower than that obtained at the Nafion/Ru modified electrode. The Nafion/PSS/Ru composite film-modified indium tin oxide (ITO) electrode also exhibited good ECL stability. In addition, this kind of immobilization approach was simple, effective, and timesaving.     

A selective and sensitive chemosensor for Cu based on 8-hydroxyquinoline

A novel 8-hydroxyquinoline derivative 3 was synthesized. Significant fluorescent quenching was found in the presence of Cu²⁺ and Hg²⁺ with notably higher selectivity for Cu²⁺ than Hg²⁺.     

An electrochemical sensor based on TiO2/activated carbon nanocomposite modified screen printed electrode and its performance for phenolic compounds detection in water samples

Herein, we reported a titanium oxide (TiO₂) modified activated carbon nanocomposite that showed advantageous characteristics in terms of electro-conductivity, catalytic activity and surface area. The designed nanocomposite was employed to modify the screen printed carbon electrode transducer surface in the construction of an electrochemical sensor. The electrode surface modification was characterised by cyclic voltammetry and impedimetric studies. The modified transducer surface was subsequently used for the detection of four phenolic endocrine disruptors, p-nitrophenol, hydroquinone, catechol and 1-naphtol. Under optimal conditions, TiO₂ modified activated carbon sensor was evaluated by differential pulse voltammetry showing a good linearity with correlation coefficients higher than 0.99. It showed, in parallel, a high sensitivity where the detection limits were 348 ng/L, 110.1 ng/L, 3.3 ng/L and 7.2 µg/L for the respective studied compounds (S/N = 3). Finally, we validated the method with river water samples, and good recovery values were obtained showing the potential application of the reported biosensor.     

电解液对全铅单液流电池电极性能的影响

研究Pb(II)和H+离子浓度对全铅单液流电池正、负电极在复合石墨基体上电化学行为的影响.结果表明,PbO2正极和Pb负极的电极过程受电化学和扩散混合控制.Pb(II)氧化沉积成PbO2时出现成核环,铅负极成核过电位小,充放电电压差远小于PbO2正极,电池极化主要来自PbO2正极.增加H+浓度有利于降低PbO2正极和Pb负极的极化,但析氧、析氢副反应和腐蚀加重.增大Pb(II)浓度有利于抑制析氧,但PbO2正极充电电压升高,充放电电压差增大.Pb(II)浓度较低时,充放电过程中PbO2沉积层少许脱落,充电电压进一步降低且更趋平稳.为此,电解液中HBF4浓度以2 mol L-1为宜,Pb(II)浓度应在0.9 mol L-1以上.     

A novel amperometric sensor for the detection of difenidol hydrochloride based on the modification of Ru(bpy)3 on a glassy carbon electrode

An amperometric sensor for the detection of difenidol, a tertiary amine-containing analyte, was proposed. Ruthenium(II) tris(bipyridine)/multi-walled carbon nanotubes/Nafion composite film was suggested to modify the glassy carbon electrode. The modified electrode was shown to be an excellent amperometric sensor for the detection of difenidol hydrochloride. The linear range is from 1.0 × 10⁻⁶ to 3.3 × 10⁻⁵ M with a correlation coefficient of 0.998. The limit of detection was 5 × 10⁻⁷ M, which was obtained through experimental determination based on a signal-to-noise ratio of three. The sensor was employed to the determination of the active ingredients in the tablets containing difenidol hydrochloride.