Self-Q-switched and mode-locked 946 nm Cr,Nd:YAG laser

A simultaneous self-Q-switched and mode-locked diode-pumped 946 nm laser by using a Cr,Nd:YAG crystal as gain medium as well as saturable absorber is demonstrated for the first time as we know. The maximum average output power of 751 mW with a slope efficiency of 18.38% is obtained at an intra-cavity average peak power intensity of 4.83 × 10⁶ W/cm². Under this circumstance, the repetition rate of Q-switched envelopes is 9.63 kHz and the pulse width is about 460 ns. Almost 100% mode-locked modulation depth is obtained at all time in the experiment process whether the incident pump power is low or high. The repetition rate of mode-locked pulses within a Q-switched envelope is 135.13 MHz and the mode-locked pulse width is within 600 ps. The laser produces high-quality pulses in TEM₀₀-mode in the simultaneous self-Q-switched and mode-locked experiment.     

Anisotropic nonlinear optical absorption of gold nanorods in a silica matrix

Nanocomposite films consisting of gold nanospheres or gold nanorods embedded in a silica matrix have been prepared using a hybrid deposition technique consisting of plasma-enhanced chemical vapor deposition of SiO₂ and co-sputtering of gold, followed by annealing at 900 °C. Subsequent irradiation with 30 MeV heavy ions (Cu⁵⁺) was used to form gold nanorods. Linear and nonlinear optical properties of this material are closely related with the surface plasmon resonance in the visible. The nonlinear absorption coefficient (α₂@532 nm) for the films containing gold nanospheres was measured by Z-scan and P-scan techniques, and it was found to be isotropic and equal to −4.8 × 10⁻² cm/W. On the contrary, gold nanorods films exhibited two distinct surface plasmon resonance absorption bands giving rise to a strong anisotropic behavior, namely a polarization-dependent linear absorption and saturable absorption. Z-scan and P-scan measurements using various light polarization directions yielded nonlinear absorption coefficient (α₂@532 nm) values varying from −0.9 × 10⁻² cm/W up to −3.0 × 10⁻² cm/W. Linearity of the P-scan method in the context of nanocomposite saturable absorption is also discussed.     

Nonlinear optical properties of periodic gold nanoparticle arrays

Periodic Au nanoparticle arrays were fabricated on silica substrates using nanosphere lithography. The identical single-layer masks were prepared by self-assembly of polystyrene nanospheres with radius R = 350 nm. The structural characterization of nanosphere masks and periodic particle arrays was investigated by atomic force microscopy. The nonlinear optical properties of the Au nanoparticle arrays were determined using a single beam z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that periodic Au nanoparticle arrays exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 6.09 × 10⁻⁶ cm²/kW and β = −1.87 × 10⁻⁶ m/W, respectively.     

Short pulse passively Q-switched Nd:GdYVO4 laser using a GaAs mirror

We report on a diode pumped passively Q-switched Nd:Gd_0.64Y_0.36VO₄ laser with a Cr⁴⁺:YAG saturable absorber. We show experimentally that by using an appropriately coated GaAs wafer as output coupler, the Q-switched pulse width can be significantly suppressed. Stable Q-switched pulse train with pulse width of 2.2 ns, peak power of 26.3 kW, repetition rate of 15.38 kHz have been obtained under an absorbed pump power of 8.54 W. The physical mechanism of pulse width narrowing by the GaAs wafer was also experimentally investigated.     

Single beam Z-scan measurement of the third order optical nonlinearities of styryl7 dye

The optical nonlinearity of styryl7 dye in ethanol solution at different concentrations has been studied using pulsed Nd:YAG laser at 532 nm as the source of excitation. The optical responses were characterized by measuring the intensity dependent refractive index (n₂) of the medium using the Z-scan technique. The open aperture Z-scan trace of the dye in solution displayed saturable absorption. The closed aperture Z-scan trace of the dye exhibited a negative nonlinearity. The styryl7 dye at 1 mM concentration exhibited nonlinear refractive co-efficient n₂ = −1.24 × 10⁻⁸ cm²/W, nonlinear absorption coefficient β = − 3.9 × 10⁻⁴ cm/W and real and imaginary parts of third-order nonlinear optical susceptibility χ³ = 3.26 × 10⁻⁶ esu in ethanol. These results showed that the dye has potential application in nonlinear optics.     

Nonlinear optical properties of an azo-based dye irradiated by picosecond and nanosecond laser pulses

The nonlinear optical properties of an azo-based dye were investigated using Z-scan technique employing 38 ps pulses at 532 and 1064 nm, and 6 ns laser pulses at 532 nm. Large nonlinear absorption and nonlinear refraction were observed at both ps and ns 532 nm in the azoic dye. When excited at ps 1064 nm, this dye displayed a large two-photon absorption cross-section (σ₂=1810 GM). Meanwhile, the optical nonlinearity mechanism was discussed in terms of molecular structure, excitation wavelength, and pulse width.     

Mg-based photocathodes prepared by ns, ps and fs PLD for the production of high brightness electron beams

Mg-based films have been prepared by pulsed laser deposition technique for photocathode applications. We have investigated the influence of pulse laser duration on morphology and photoemissive properties. Two laser sources have been used, generating pulses of 30 ns at 308 nm (XeCl excimer laser), 5 ps and 500 fs at 248 nm (KrF excimer laser) to grow Mg films onto Si and Cu substrates in high vacuum (∼10⁻⁷ Pa) and at room temperature. Morphological investigations carried out by scanning electron microscopy (SEM) have revealed that, in our experimental conditions, the number and the mean size of the droplets on the films surfaces decreases as the pulse laser duration shortens. The contamination level of Mg film surfaces have been studied by energy dispersive X-ray spectroscopy (EDX). The photoelectron performances in terms of quantum efficiency (QE) and emission stability have been tested in a UHV DC photodiode cell (10⁻⁷ Pa). Measures of the QE of the samples surfaces have revealed a decrease on the initial value for Mg-based photocathodes prepared by fs laser (from 7.8 × 10⁻⁴ to 6.6 × 10⁻⁴) PLD with respect to ps (from 6.2 × 10⁻⁴ to 7.4 × 10⁻⁴) and ns lasers (from 5.0 × 10⁻⁴ to 1.6 × 10⁻³). A comparison among Mg-based photocathodes prepared by ns, ps and fs PLD for the production of high brightness electron beams has been presented and discussed.     

Diode-pumped passively Q-switched Nd:LuVO4 laser at 916 nm

We demonstrate a passively Q-switched Nd:LuVO₄ laser at 916 nm by using a Nd, Cr:YAG crystal as the saturable absorber. As we know, it is the first time to realize the laser with a simple linear resonator. When the incident pump power increased from 14.6 W to 23.7 W, the pulse width of the Q-switched laser decreased from 24 ns to 21 ns. The pulse width was insensitive to the incident pump power in the experiment. The average output power of 288 mW with repetition rate of 39 kHz was obtained at an incident pump power of 22.5 W, with the optical-to-optical efficiency and slope efficiency 1.3% and 3.6%, respectively.     

Diode-pumped doubly passively Q-switched c-cut Nd:GdVO4 1.34 μm laser with V:YAG and Co:LMA saturable absorbers

By simultaneously using both V³⁺:YAG and Co:LMA saturable absorbers in the cavity, a diode-pumped doubly passively Q-switched c-cut Nd:GdVO₄ laser at 1.34 μm is demonstrated for the first time. The average output power, the pulse width and the pulse repetition rate have been measured. The experimental results show that the doubly passively Q-switched laser can generate shorter pulse width with higher peak power in comparison to the singly passively Q-switched laser only with V³⁺:YAG or Co:LMA saturable absorber. At the pump power 13 W, the pulse width has been compressed 83% and the peak power has been improved 15 times, respectively.     

Diode-pumped passively Q-switched Nd:GdVO4 laser at 1342 nm with V:YAG saturable absorber

We have demonstrated an efficient diode-pumped passively Q-switched Nd:GdVO₄ laser working at 1342 nm by using an uncoated V³⁺:YAG crystal as the saturable absorber, in which both a-cut and c-cut Nd:GdVO₄ crystals are employed. At the maximum absorbed pump power of 9.45 W, the maximum average output power can reach 519 mW and 441 mW corresponding to the output coupler with different transmission of 3% and 10% by using an a-cut Nd:GdVO₄ crystal at 1342 nm, while the shortest pulse duration could be as low as 21.7 ns and 22.3 ns with the repetition rate of 48.41 kHz and 53.25 kHz by using a c-cut Nd:GdVO₄ crystal, corresponding to the output coupler with different transmission of 3% and 10% at 1342 nm, and the single Q-switched pulse energy are 6.67 uJ and 7.06 uJ, the pulse peak power are 307 W and 316 W, respectively. The experimental results show that c-cut Nd:GdVO₄ laser can generate shorter pulse with higher peak power in comparison with a-cut one.     

Passively Q-switched laser performance of c-cut Nd:Gd0.63Y0.37VO4 crystal

Passively Q-switched c-cut Nd:Gd_0.63Y_0.37VO₄ laser performance at 1.06 μm was demonstrated with Cr⁴⁺:YAG as saturable absorbers for the first time to our knowledge. This c-cut mixed crystal was found to have large energy storage capacity. The shortest pulse width, largest pulse energy, and highest peak power were obtained to be 6.6 ns, 201.7 μJ, and 30.6 kW, respectively.     

LD end pumped, actively mode locked and passively Q-switched Nd:YAP laser at 1341 nm

An end pumped Nd:YAP laser at 1341 nm is actively mode locked and passively Q-switched. Pumping was done with a pulsed high power laser diode with maximum power 425 W. V³⁺:YAG with 61% initial transmission served as saturable absorber, and an acousto-optic modulator is used for active mode locking. The output pulse train with 69 ns duration has a total energy of 3.2 mJ with ±4% shot-to-shot fluctuation. The peak output energy of a single mode locked pulse is 0.25 mJ. The pulse duration of a single mode locked pulse is less than 800 ps. The output laser beam is nearly diffraction limited with 1.6 mm diameter, and beam propagation factor M² about 1.3.     

Photophysical and nonlinear optical properties of an azobenzene substituted zinc phthalocyanine

Photophysical property and third-order optical nonlinearity of an azobenzene substituted zinc phthalocyanine (azo-ZnPc) in chloroform solution were studied by UV–Vis spectra method and a picosecond Z-scan technique at 532 nm with pulse duration of 25 ps, respectively. It was found that the azo-ZnPc shows large positive nonlinear refraction and positive nonlinear absorption, exhibiting the defocusing effect and reverse saturable absorption, respectively. The molecular second hyperpolarizability of the azo-ZnPc dyad was measured to be 3.9 × 10⁻³⁰ esu. All the results suggest that the studied azo-ZnPc dyad may have potential applications in the field of nonlinear optics.     

Anisotropy of two-photon absorption in gallium selenide at 1064 nm

The Bridgman method is used to grow single crystals of ε-GaSe. The two-photon absorption (TPA) coefficient β was measured for especially un-doped crystals at room temperature for the ordinary o-ray (β_⊥) and extraordinary e-ray (β_∥) using single-wavelength excitation by a Nd:YVO₄ laser at 1.064 μm with a pulse duration of 10 ps and a repetition rate of 81 MHz. No large anisotropy was observed for the TPA coefficients between the two geometries. The TPA coefficients were found to be β_⊥ = 1.07 × 10⁻⁹ cm/W and β_∥ = 1.88 × 10⁻⁹ cm/W. It was found that doping slightly increases the TPA coefficient. The value of the TPA for crystals doped with 0.5 at.% of Tl is β_⊥ = 7.56 × 10⁻⁹ cm/W.     

Study on nonlinear optical absorption properties of [(CH3)4N]2[Cu(dmit)2] by Z-scan technique

The third-order optical nonlinearities of an organo-metallic compound, [(CH₃)₄N]₂[Cu(dmit)₂] (dmit²⁻=4,5-dithiolate-1,3-dithiole-2-thione), abbreviated as MeCu, dissolved in acetone are characterized by Z-scan technique with picosecond and nanosecond laser pulses in the near-infrared region. Two-photon absorption has been found when the sample solution is irradiated by 40 ps pulse width at 1064 nm and the two-photon absorption (TPA) coefficient β_TPA is 4×10⁻¹³ m/W. While excited by 15 ns laser pulses at 1053 nm, the Z-scan spectra reveal strong reverse saturable absorption (RSA) and the nonlinear absorption coefficient β_RSA is estimated to be as high as 7.07×10⁻¹¹ m/W which is much larger than β_TPA. An explanation for this enhancement is given. All the results suggest that MeCu may be a promising candidate for the application to optical limiting in the near-infrared region.     

Study of optical nonlinearity of functionalized multi-wall carbon nanotubes by using degenerate four wave mixing and Z-scan techniques

The phase conjugation geometry of degenerate four wave mixing (DFWM) technique has been employed to study the third-order optical nonlinear susceptibility (χ³) and second-order hyperpolarizability of multi-wall carbon nanotubes (MWCNTs). MWCNTs were grown by thermal chemical vapor deposition method and, subsequently functionalized with carboxylic acid group to improve their solubility in an organic solvent, ethylene glycol. The average hyperpolarizability for each carbon atom has been found to be 4.74 × 10⁻⁴⁶ m⁵/V² for the pump pulse of 8 ns at 532 nm. Decreasing the pulse width of the pump laser decreases the average value of hyperpolarizability. The absorption spectra show a monotonous increase from IR through visible and give an opportunity to estimate the imaginary part of the χ³ by the open aperture Z-scan technique.     

Line patterning with large refractive index changes in the deep inside of glass by nanosecond pulsed YAG laser irradiation

Nanosecond (∼100 ns) pulsed (10 Hz) Nd:YAG laser operating at the wavelength (λ) of 1064 nm with pulse energies of 0.16-1.24 mJ/cm² has irradiated 10Sm₂O₃·40BaO·50B₂O₃ glass. It is demonstrated for the first time that the structural modification resulting the large decease (∼3.5%) in the refractive index is induced by the irradiation of YAG laser with λ=1064 nm. The lines with refractive index changes are written in the deep inside of 100-1000 μm depths by scanning laser. The line width is 1-13 μm, depending on laser pulse energy and focused beam position. It is proposed that the samarium atom heat processing is a novel technique for inducing structural modification (refractive index change) in the deep interior of glass.     

Thermal effects investigation and cavity design in passively mode-locked Nd:YVO4 laser with a SESAM

A diode-pumped passively mode-locked Nd:YVO₄ laser with a five-mirror folded cavity is presented by using a semiconductor saturable absorber mirror (SESAM). The temperature distribution and thermal lensing in laser medium are numerically analyzed to design a special cavity which can keep the power density on SESAM under its damage threshold. Both the Q-switched and continuous-wave mode-locked operation are experimentally realized. The maximum average output power of 8.94 W with a 9.3 ps pulse width at a repetition rate of 111 MHz is obtained under a pump power of 24 W, correspondingly the optical slope efficiency is 39.2%.     

Effects of electron relaxation on multiple harmonic generation from metal surfaces with femtosecond laser pulses

Calculations are presented for the first four (odd and even) harmonics of an 800 nm laser from a gold surface, with pulse widths ranging from 100 down to 14 fs. For peak laser intensities above 1 GW/cm² the harmonics are enhanced because of a partial depletion of the initial electron states. At 10¹¹ W/cm² of peak laser intensity the calculated conversion efficiency for 2nd-harmonic generation is 3 × 10⁻⁹, while for the 5th-harmonic it is 10⁻¹⁰. The generated harmonic pulses are broadened and delayed relative to the laser pulse because of the finite relaxation times of the excited electronic states. The finite electron relaxation times cause also the broadening of the autocorrelations of the laser pulses obtained from surface harmonic generation by two time-delayed identical pulses. Comparison with recent experimental results shows that the response time of an autocorrelator using nonlinear optical processes in a gold surface is shorter than the electron relaxation times. This seems to indicate that for laser pulses shorter than ∼30 fs, the fast nonresonant channel for multiphoton excitation via continuum-continuum transitions in metals becomes important as the resonant channel becomes slow (relative to the laser pulse) and less efficient.     

Nonlinear optical properties in SrTiO3 thin films by pulsed laser deposition

Well-crystallized 250 nm-thick SrTiO₃ thin films on fused-quartz substrate were prepared by pulsed laser deposition. The band-gap of SrTiO₃ thin film by transmittance spectra is equal to 3.50 eV, larger than 3.22 eV for the bulk crystal. The nonlinear optical properties of the films were examined with picosecond pulses at 1.064 μm excitation. A large two-photon absorption (TPA) with absorption coefficient of 87.7 cm/GW was obtained, larger than 51.7 cm/GW for BaTiO₃ thin films. The nonlinear refractive index n₂ is equal to 5.7×10⁻¹⁰ esu with a negative sign, larger than 0.267×10⁻¹¹ esu for bulk SrTiO₃. The large TPA is attributed to intermediate energy levels introduced by the grain boundaries, and the optical limiting behaviors stemming from both TPA and negative nonlinear refraction were also discussed.