超分辨技术在光盘中的应用研究

超分辨技术是一种无需用减小波长或增大数值孔径的方法减小记录点尺寸而能读出超过衍射极限信号从而有效增加存储密度的一种方法.超分辨可以通过调整光学系统或者调整光盘的结构来实现.在超分辨光盘中,超分辨是基于掩膜的光学性质随入射激光强度的非线性变化而实现的.在磁光盘中第一次引入超分辨技术后,超分辨技术的应用有了很大发展,在目前是提高光盘存储密度的有效方法,在各类光盘中都有良好的应用.近场超分辨技术的出现使相变光盘的超高密度记录和读出成为可能.文章综述了超分辨光盘的发展现状和发展方向.     

超分辨近场结构光盘的传统以及差分读出方法研究

利用标量衍射理论和角谱方法,针对超分辨近场结构光盘存储系统建立了简单物理模型,并提出了超分辨近场结构光盘的读出信号仿真计算方法.通过对比实际测试信号与模拟信号,证明了该读出信号计算方法的可行性.此外,针对超分辨掩膜层对不同功率入射激光响应不同的特性,分别分析了单轨道和三轨道记录符在高、低功率两束激光读出下的差分信号.数...     

一种新的超分辨记录点的读出技术

提出一种新的超分辨记录点的读出技术—超分辨反射膜技术，详细分析了其原理。用该技术，以Sb为超分辨反射膜，SiN为介电层，在激光波长为632．8nm和光学头的数值也径为0．40的读出光学系统中实现了直径为380nm的超分辨记录点的读出。同时研究了Sb薄膜厚度对读出信噪比的影响规律，发现最佳的Sb薄膜厚度为28～30nm，所得的信噪比为38～40dB。     

Si掺杂Ag基超分辨薄膜读出性能研究

超分辨薄膜是一种能够实现突破光学衍射极限的功能薄膜,它在超分辨近场光存储技术中起到至关重要的作用。采用磁控溅射共溅的方式制备了Ag掺杂一定量Si的超分辨复合薄膜,测试了其作为掩膜层的超分辨光盘读出性能,并获得了最佳的薄膜制备条件,即当Ag溅射功率为55 W,Si为95 W,溅射时间为80s,薄膜厚度为39nm时,超分辨光盘的读出信号载噪比(CNR)最高为28dB。用X射线光电子能谱测量了上述薄膜的组成,用扫描电子显微镜观察了薄膜微区形貌,并用椭圆偏振光谱仪测量了薄膜的光学常数和厚度。超分辨复合薄膜的读出机理可以用Ag的散射型机理解释。光盘在持续读出10万次以后读出信号基本没有下降。     

光盘存储读出信道的实现

通过构建适合于硬件电路实现的读出信道数学模型以及对光存储系统中存在的噪声、抖晃和扰动的分析,在FPGA(Field programmable gate array)硬件平台上,实现了对任意二阶至四阶记录光盘读出RF(Radio frequency)信号的模拟实时连续输出。在信道模拟的硬件算法设计中,采用了四倍频的方法和基于ROM(Read-only memory)查找表的方法实现了100Mbit高速情况下的卷积运算。设计结果得到了逼真的网眼图,验证了模型的正确性,且已作为光盘系统后续信号处理模块的信源,加快了光盘系统研制开发的步伐。     

近场光存储及其研究进展

本文从近场光学的超分辨原理出发详细介绍和分析了孔径探针型近场光存储技术，SIL透镜近场光存储技术和近场超分辨结构光盘存储技术等的基本原理、研究现状以及它们的优缺点及存在的问题。     

超分辨近场结构技术及其应用

超分辨近场结构(Super RENS)技术是在传统的超分辨光盘技术和近场光学的基础上发展起来的新技术。介绍了Super RENS技术的基本原理:利用掩膜层的非线性效应或表面等离子体增强效应,在近场区域可以记录、读出超过衍射极限的信号。综述了该技术在纳米光信息存储和光刻方面应用研究的最新进展,提出了存在的问题,展望了它的发展前景。     

二元光学元件和新型超分辨光盘读写头的设计研究

本文采用杨-顾相位恢复算法数值模拟设计了一个用于光盘读写头的二元光学元件,并构思了一种新型超分辨光盘读写头,在现有光盘读写头的激光波长处和数值孔径基础上,利用该二元光学元件实现光学超分辨,从而提高光盘存储容量.     

多阶游程长度受限编码的光盘读出信号

多阶游程长度受限(ML-RLL)编码可以在保持原有记录符尺寸和记录单元数量的情况下将CD光盘存储容量提高2.4倍。借助标量衍射理论建立了多阶游程长度受限记录符的计算模型,对采用多阶游程长度受限编码的CD光盘的读出信号进行了仿真分析。结果表明,记录坑长度的变化对读出信号幅值影响较小,有利于将记录坑长度和记录坑的宽度两个参数进行分离检测,但在3T长度、不同宽度的记录坑相连的情况下,从读出信号中很难分辨出记录符的分界位置。     

超分辨近场结构光盘读出信号的计算模型

给出了超分辨近场结构光盘(Super RENS)读出信号的计算模型。以时域有限差分法为基础,结合高斯光束矢量模型和衍射方法,通过计算得到了物镜出瞳上的读出信号。计算结果表明,Super RENS具有超衍射极限的空间分辨能力,并且其读出信号的特征完全不同于传统光盘。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.