Measurements of coeluting unlabeled and C-labeled polychlorinated biphenyl congeners with partially overlapping fragment profiles using a tandem mass spectrometry

¹³C-labeled compounds are often employed as surrogate or internal standards to monitor the performance of extraction and instrumental analysis procedures for their unlabeled counterparts. However, labeled and unlabeled counterparts most often coelute chromatographically with overlapping mass ion fragments, posing a challenge to the accurate quantification of these compounds. In the present study, an analytical scheme, using coeluting unlabeled and ¹³C-labeled polychlorinated biphenyl (PCB) congeners as the model compounds, was developed with a low-resolution tandem mass spectrometer (MS/MS) to determine the appropriate ranges of PCB congener concentrations that satisfy the no-interference condition. Interferences from unlabeled PCBs to quantitation of labeled counterparts could be minimized when ¹³C-labeled PCB congeners were quantified in the MS/MS mode within a certain concentration range. In addition, good agreements between the measured and theoretically predicted quantitation errors were observed for all labeled PCB congeners except PCB 180. The exception with labeled PCB 180 was mainly attributed to the occurrence of instrumental analytical uncertainty, as analytical error was also observed with absence of unlabeled PCB 180. These results indicate that MS/MS techniques can serve as a useful tool to minimize interferences with quantitation of isotopically labeled compounds from their unlabeled counterparts, which possess partially overlapping ion fragment profiles.     

Gas chromatography of 209 polychlorinated biphenyl congeners on an extremely efficient nonselective capillary column

The gas chromatographic–mass spectrometric (GC–MS) separation of all 209 polychlorinated biphenyl (PCB) congeners was studied on an extremely efficient 80 m × 0.1 mm i.d. capillary column coated with a 0.1 μm film of poly(5%-phenyl methyl)siloxane stationary phase. The quality of the separation and the number of resolved and coeluting peaks were compared to predictions according to the statistical overlap theory (SOT) and to literature data on PCB separations obtained by one-dimensional and comprehensive two-dimensional GC (GC × GC) and GC–MS. Mass spectral and chemometric deconvolution procedures were used to resolve overlapping peaks. On the highly efficient column, 195 PCB congeners were resolved in 96 min separation time using spectral and chemometric deconvolution. This number is comparable to the best separations described in GC × GC–MS mode. The novel method was developed for spectral deconvolution of overlapped PCB congeners which was verified determining the most toxic, dioxin-like PCBs both in the model mixture of 209 PCBs as well as in the Aroclor 1242 and Aroclor 1254 formulations.     

Analysis of seven chlorobiphenyl congeners by multidimensional gas chromatography

Chlorobiphenyl congeners (CBs) are used as indicator compounds in analysis performed to determine whether or not PCB concentrations in food products, waste mineral oil, and environmental samples comply with the maximum levels permitted by legislation. Seven of these compounds have been checked for coelution with other CB congeners by means of a multidimensional gas chromatographic method utilizing a combination of two narrow bore columns, one coated with a conventional non-polar stationary phase and the other with a liquid crystalline (smectic) stationary phase. Peaks of the relevant CBs have been transferred, by heart cutting, from the non-polar column to the liquid crystal column, on which unambiguous separation from possible coeluting CB congeners was obtained. It has been shown that if the seven congeners are analyzed solely on a single, non-polar capillary column the results obtained for two of them may be affected by coelution of other compounds.     

Analysis and deconvolution of dimethylnaphthalene isomers using gas chromatography vacuum ultraviolet spectroscopy and theoretical computations

An issue with most gas chromatographic detectors is their inability to deconvolve coeluting isomers. Dimethylnaphthalenes are a class of compounds that can be particularly difficult to speciate by gas chromatography – mass spectrometry analysis, because of their significant coelution and similar mass spectra. As an alternative, a vacuum ultraviolet spectroscopic detector paired with gas chromatography was used to study the systematic deconvolution of mixtures of coeluting isomers of dimethylnaphthalenes. Various ratio combinations of 75:25; 50:50; 25:75; 20:80; 10:90; 5:95; and 1:99 were prepared to test the accuracy, precision, and sensitivity of the detector for distinguishing overlapping isomers that had distinct, but very similar absorption spectra. It was found that, under reasonable injection conditions, all of the pairwise overlapping isomers tested could be deconvoluted up to nearly two orders of magnitude (up to 99:1) in relative abundance. These experimental deconvolution values were in agreement with theoretical covariance calculations performed for two of the dimethylnaphthalene isomers. Covariance calculations estimated high picogram detection limits for a minor isomer coeluting with low to mid-nanogram quantity of a more abundant isomer. Further characterization of the analytes was performed using density functional theory computations to compare theory with experimental measurements. Additionally, gas chromatography – vacuum ultraviolet spectroscopy was shown to be able to speciate dimethylnaphthalenes in jet and diesel fuel samples.     

Importance of enhanced mass resolution in removing interferences when measuring volatile organic compounds in human blood by using purge-and-trap gas chromatography/mass spectrometry

The number of volatile organic compounds (VOCs) that can be purged from human blood is so great that they cannot be separated completely by capillary gas chromatography. As a result, the single-mass chromatograms used for quantitating the target compounds by mass spectrometry have many interferences at nominal (integer) mass resolution of a quadrupole mass spectrometer. The results of these interferences range from small errors in quantitation to completely erroneous results for the target VOCs. By using a magnetic sector mass spectrometer, these interferences at nominal mass can be removed at higher resolution by lowering the ion chromatogram windows around the masses of interest. At 3000 resolution (10% valley definition), unique single-ion chromatograms can be made for the quantitation ions of the target VOCs. Full-scan mass data are required to allow the identification of unknown compounds purged from the blood. By using isotope-dilution mass spectrometry, most target VOCs can be detected in the low parts per trillion range for a 10-mL quantity of blood from which the VOCs have been removed by a purge-and-trap method.     

Enhanced comprehensive two-dimensional gas chromatographic resolution of polychlorinated biphenyls on a non-polar polysiloxane and an ionic liquid column series

A total of 196 out of 209 polychlorobiphenyl (PCB) congeners were resolved using GC×GC-TOFMS with a non-polar/ionic liquid column series consisting of poly(50%-n-octyl-50%-methyl)siloxane and (1,12-di(tripropylphosphonium)dodecane bis(trifluoromethansulfonyl)amide) in the first and second dimension, respectively. It has been found that 13 PCB congeners overlap in five doublets (CB12+CB13, CB62+CB75, CB70+CB76, CB97+CB125 and CB153+CB168) and one triplet (CB90+CB101+CB113). All toxic, "dioxin like" congeners were separated with no interferences from any PCB congener. The 109 PCBs present in Aroclor 1242 and the 82 PCBs present in Aroclor 1260 were resolved GC×GC-TOFMS analysis on this column set.     

Evaluation of an automated clean-up system for the isotope-dilution high-resolution mass spectrometric analysis of PCB, PCDD, and PCDF in food

An automated clean-up system was evaluated for the simultaneous analysis of polychiorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF), and biphenyls (PCB) in different foods. In addition to the seventeen 2,3,7,8-substituted PCDDIPCDF and four non-ortho PCB, by use of the clean-up system studied, it was possible to collect the eight mono-ortho and two di-ortho PCB and the seven indicator PCB in two separate fractions during the same clean-up run. The study was first performed using standard mixtures containing PCDD, PCDF and PCB, and a certified reference material. The recoveries of the 13C-labeled compounds ranged from 51 to 90%, indicating that the PCDD, PCDF, and PCB clean-up worked satisfactorily. Next, the automated system for PCDD, PCDF, and PCB analysis was evaluated for foods such as milk, egg, meat (beef, chicken, and pork), mussel, and olive oil. The recoveries of the 13C-labeled compounds ranged from 40 to 120% for PCB and from 57 to 113% for PCDD/ PCDF, meeting the requirements of well accepted methods. Thus, the automated clean-up system studied is a suitable alternative to conventional clean-up methods.     

A rapid screening method for routine congener-specific analysis of polychlorinated biphenyls in human serum by high-resolution gas chromatography with mass spectrometric detection

A screening method using gas chromatography/mass spectrometry in the single ion monitoring (SIM) mode for the routine congener-specific analysis of polychlorinated biphenyls (PCBs) in human serum has been developed and validated. A fast procedure incorporating both liquid-liquid and solid-phase extraction was used for clean up and enrichment. Interday and intraday precision and accuracy were assessed for the 12 congeners having dioxin-like activity and PCBs #180 and #170 by analyzing spiked samples on three subsequent days and using (13)C(12)-labelled analogues as internal standards. Furthermore, the relative errors for six non-dioxin-like congeners (PCBs #28, #52, #101, #138, #153 and #180) were measured by using certified reference materials, providing good accuracy at two different concentration levels. The limits of quantification and of detection were 0.5 and 0.2 micro g/L in serum for each congener, respectively. The method allows the chromatographic separation of at least 35 congeners and can therefore be applied to the routine monitoring of the general population for both dioxin-like and non-dioxin-like PCB congeners.     

Packed columns vs. wall coated open tubular columns in quantitative analyses of polychlorinated biphenyls

This article describes and critically evaluates a complete method for the quantitation of PCB in sediment samples. The extraction and clean-up procedure is described. Packed column and capillary column results are compared. Capillary column quantitation yields lower values for total PCB loading. Preferences for capillary column quantitation are discussed and explained. Capillary quantitation is based on the combination of an external Aroclor standard and an internal decachlorobiphenyl standard for normalizing data. In light of the recent report of synthesis of all 209 PCB congeners a suggestion is made to use these as absolute standards to establish a bank of primary standard Aroclors.     

Quantitative analysis of polybrominated diphenyl ethers in adipose tissue, human serum and foodstuff samples by gas chromatography with ion trap tandem mass spectrometry and isotope dilution

A method based on gas chromatography (GC) separation followed by ion trap tandem mass spectrometry detection in EI mode (ITD-MS/MS), using isotope dilution, was developed for the determination of ten native polybrominated diphenyl ethers (PBDEs) and four (13)C(12)-labeled congeners in biological (fat tissue and human serum) and food samples. The highest-mass fragment ions were used as precursor ions for those congeners with molecular ions with m/z values higher than the maximum of the instrument. In these cases (hepta-BDEs and (13)C(12)-hexa-BDEs) no fragmentation was achieved under the experimental conditions employed. Repeatability (lower than 9%) and reproducibility (lower than 13%), expressed as relative standard deviation (RSD, n = 3 and 4, respectively), were satisfactory. Similarly, the coefficient of variation (n = 4) of the isotopic ratio between the two most abundant product ions was lower than 10 and 6% for native and labeled congeners, respectively. To evaluate the feasibility of the method, the optimized isotope dilution GC/ITD-MS/MS method was used for the quantitation of selected PBDE congeners in different samples including adipose tissue, human serum and foodstuff samples, from three inter-laboratory comparative exercises, covering a wide range of concentrations. A solid-phase extraction procedure, previously developed for PCB determination in small-size bird serum samples, was successfully applied to quantification of PBDEs in 1 mL samples of human serum.     

Marine mammal blubber reference and control materials for use in the determination of halogenated organic compounds and fatty acids

The National Institute of Standards and Technology (NIST) has a diverse collection of control materials derived from marine mammal blubber, fat, and serum. Standard Reference Material (SRM) 1945 Organics in Whale Blubber was recertified for polychlorinated biphenyl (PCB) congeners, organochlorine pesticides, and polybrominated diphenyl ether (PBDE) congeners. SRM 1945 has also been assigned mass fraction values for compounds not frequently determined in marine samples including toxaphene congeners, coplanar PCBs, and methoxylated PBDE congeners which are natural products. NIST also has assigned mass fraction values, as a result of interlaboratory comparison exercises, for PCB congeners, organochlorine pesticides, PBDE congeners, and fatty acids in six homogenate materials produced from marine mammal blubber or serum. The materials are available from NIST upon request; however, the supply is very limited for some of the materials. The materials include those obtained from pilot whale blubber (Homogenates III and IV), Blainville’s beaked whale blubber (Homogenate VII), polar bear fat (Homogenate VI), and California sea lion serum (Marine Mammal Control Material-1 Serum) and blubber (Homogenate V).     

Porous glass as an efficient adsorbent for volatile atmospheric polychlorinated biphenyl congeners

Porous glass is a more efficient adsorbent than Amberlite XAD-2 resin for volatile polychlorobiphenyls (PCB) in the atmospheric vapour phase. The adsorption efficiencies for individual PCB congeners are compared by analysis of the extracts by capillary gas chromatography (electron-capture detection); individual congeners are used as reference compounds. Efficiencies for some di-, tri- and tetra-chlor congeners are between 1.7 and 7 times higher the porous glass than for XAD-2 resin; values for penta-, hexa- and hepta-chloro congeners are very similar. The calculated “total” PCB (as the sum of individual congeners) was about four times higher for porous glass, because of the contribution from congeners with low chlorine numbers. Commercial mixtures may not reflect the real composition of PCB mixtures in the atmosphere.     

Determination of total and speciated sulfur content in petrochemical samples using a pulsed flame photometric detector

The pulsed flame photometric detector (PFPD) has the advantage of being able to measure the concentration of individual sulfur compounds and total sulfur content in a petrochemical sample in a single gas chromatography run. Because it is an equimolar response detector, the PFPD's sulfur response is independent of a compound's molecular structure, and this feature allows quantitation of the total or speciated sulfur content in complex samples using a single calibrant. This paper is a survey describing a variety of applications using the PFPD for sulfur quantitation in petrochemical matrices. Several different approaches to quantitation are described, and simple techniques for circumventing the quenching of the sulfur signal by coeluting hydrocarbon peaks are discussed. Examples from a range of real-world samples are presented.     

Improved Procedure for Single DB-XLB Column GC-MS-SIM Quantitation of PCB Congener Distributions and Characterization of Two Different Preparations Sold as “Aroclor 1254”

Complete PCB congener distributions in a panel of Aroclor mixtures were previously obtained by combining data from several HRGC systems. In that study quantitation of minor components may have been unreliable due to single level calibration against high levels of individual congener standards. Two lots of Aroclor 1254 had markedly different congener distributions. In this study, the design and performance of a congener-specific PCB analysis method employing GC-MS-SIM detection of congeners separated on a DB-XLB capillary column are discussed. Quantitation is carried out against a 6-level inclusive standard curve of a mixture of 144 congeners found in Aroclors. A separate procedure to measure trace levels of PCB 126 in Aroclors using the same system, combined with levels initially acquired for other congeners, facilitates estimation of TEQ values (Toxic Equivalencies of the PCB mixtures to 2,3,7,8-TCDD). PCB congener profiles of 15 Aroclor 1254 mixtures are presented. These profiles show that the less common, high TEQ variety of Aroclor 1254 was manufactured by an atypical, two-stage chlorination process that was apparently used during the final 1% of Aroclor 1254 production (ca. 1974–1976).     

气相色谱-负化学电离质谱法测定沉积物和鱼肉中毒杀芬的8个同类物及其总含量

建立了气相色谱-负化学电离源质谱测定沉积物和鱼肉中毒杀芬的8个同类物及其总量的分析方法。样品由二氯甲烷在加速溶剂萃取仪上提取,经铜粉(或凝胶渗透色谱)及硅胶和氧化铝复合柱净化,使用DB-XLB柱分离,在选择离子检测模式下同时检测毒杀芬的8个同类物及其总量。多氯联苯(PCB)的氧反应水平由内标PCB204监测,并保持在低于1%。使用平均相对响应因子定量:采用单个离子的峰面积对8个毒杀芬同类物进行定量,采用可检测到的毒杀芬同类物峰面积的和对毒杀芬总量进行定量。单个同类物的校正标准溶液质量浓度范围是0.5 (P62为5)~500 μ g/L,毒杀芬总量的校正标准溶液质量浓度范围是50~500 μ g/L。以最低校正标准溶液的浓度为最低定量浓度。同类物的日间平均回收率是(90.8±17.4)%(n=10),日间测定的相对标准偏差为5.4%~12.8%(n=10),显示了本方法有较高的准确性和精确性。应用该方法分析了沉积物和鱼肉中毒杀芬的含量。     

Spectral and non-spectral interferences in inductively coupled plasma mass-spectrometry

Inductively coupled plasma mass spectrometry of environmental and biological samples is often hampered by spectral and non-spectral interferences. Spectral interferences, caused by the limited resolution of the quadrupole mass spectrometer, can be eliminated in a variety of ways. For their identification inspection of a signal versus carrier gas flowrate is useful. Anion exchange allows the removal of most S and Cl containing compounds, which are at the origin of the majority of spectral interferences. Matrix modification, for example the addition of ethanol and subsequent optimization of the gas flow rates in a number of cases enables the reduction of the interferences to insignificant values. Often a mathematical correction based on isotopic signal ratios can be applied. Non-spectral interferences can be divided in reversible, that is occurring while the sample is being measured, and irreversible matrix effects, that is clogging of the nebulizer and sampling orifices or deposition on the torch or in the ion lens stack. The errors associated with non-spectral interferences can be eliminated by appropriate calibration procedures, adapted sample preparation or limitation of the amount of sample delivered to nebulizer, plasma and sampling devices, for example by the application of flow injection. Applications of all the elimination procedures are described for the analysis of sea-water, estuarine water, soil and sewage extracts, percolate water, urine, serum and wine.     

Certification of SRM 1589a PCBs,pesticides, PBDEs,and dioxins/furans in human serum

The Certificate of Analysis for SRM 1589a PCBs, Pesticides, PBDEs, and Dioxins/Furans in Human Serum has been updated to include certified concentration values for 27 polychlorinated biphenyl (PCB) congeners, three chlorinated pesticides, and four polybrominated diphenyl ether (PBDE) congeners as well as reference concentration values for 27 additional PCB congeners, six additional chlorinated pesticides, three additional PBDE congeners, and selected polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs). This represents an addition of concentration values for 29 PCB congeners and for PBDE congeners that were not quantified in the previous issue of SRM 1589a. With the increased number of certified and reference concentration values for PCBs and the inclusion of certified and reference concentration values for PBDEs, this serum material will be more useful as a reference material for contaminant monitoring in human tissues and fluids. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Determination of toxic PCB congeners in biological samples by multidimensional gas chromatography-mass spectrometry (GC/GC/MS)

Summary Multidimensional gas chromatography-mass spectrometry (GC/GC/MS) was used for the determination of coplanar PCB congeners in biological samples. A quadrupole low resolution mass spectrometer was used as the main detector in order to increase the reliability of identification and enable the use of ¹³C-labelled internal standards. The technique was capable to separate these toxic congeners from the complex matrix and decreased the need of sample purification.     

Anaerobic Degradation of PCB in Soils

Abstract

The anaerobic degradation of PCB in loamy and clayey soils containing indigeneous microflora was studied. The anaerobic conditions were created by an argon atmosphere in the flasks containing soil flooded by a liquid medium with glucose. GC-ECD analysis of soil extracts after 40 day incubation showed, in addition to the concentration changes of the less chlorinated PCB congeners, a significant decrease in the concentration of highly chlorinated congeners in both soils. The results indicate that in both soil types reductive dehalogenation of PCB congeners was encountered.     

Femtogram detection of perfluorocarbon tracers using capillary gas chromatography-electron-capture negative ion chemical ionisation mass spectrometry

An ultrasensitive and selective method has been developed for the detection of a range of perfluorocarbon tracers suitable for long-range atmospheric studies. Following direct injection onto a capillary column the perfluorocarbons are separated and detected using mass spectrometry with electron-capture negative ion chemical ionisation (ECNICI-MS) with methane as reagent gas and selected-ion monitoring. All nine perfluorocarbons tested underwent non-dissociative resonance electron capture to form the molecular anion which was the base peak in all cases. Using this technique, detection limits (signal-to-noise ratio of 2:1) of 3 and 2 fg were obtained for perfluoromethylcyclohexane and perfluoro-1,3-dimethylcyclohexane respectively. The corresponding detection limits using a conventional electron-capture detector were 8 and 9 fg respectively. In addition to increased sensitivity, the ECNICI-MS technique allows temperature programming for the simultaneous analysis of a range of perfluorocarbons and has superior selectivity being less prone to coeluting interferences. Furthermore the method is potentially one to two orders of magnitude more sensitive than the current gas chromatography-MS methods using 13C2H4 tracers.