Characteristics of Ga and Ag-doped ZnO-based nanowires for an ethanol gas sensor prepared by hot-walled pulsed laser deposition

Pure ZnO and Ga (3 % w/w) and Ag (3 % w/w)-doped ZnO nanowires (NWs) have been grown by use of the hot-walled pulse laser deposition technique. The doping characteristics of Ga and Ag in ZnO NWs were analyzed by use of photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS) and the results were compared with those for pure ZnO NWs. We also fabricated gas sensors by use of pure ZnO and Ga and Ag-doped ZnO NWs. Among the NW sensors, the Ag-doped NW sensor was most sensitive. We synthesized the NWs on sapphire substrates under different conditions, for example temperature, time, gas flow, and distance between target and substrate. The diameter and length of NWs were <100 nm and several microns, respectively. To analyze the effect of Ag doping on ZnO NWs, we investigated the near band edge emission by use of low-temperature PL and XPS. Significant changes in resistance and sensitivity were observed. When the sensors were used at 300 °C for detection of 1 ppm ethanol vapor, the sensitivity of the pure ZnO and the Ga and Ag-doped ZnO NW gas sensors was 97, 48, and 203 %, respectively.     

Microwave-assisted solution synthesis and photocatalytic activity of Ag nanoparticles supported on ZnO nanostructure flowers

Ag nanoparticles supported on the surface of three-dimensional (3D) flower-like ZnO nanostructure were synthesized by a microwave-assisted solution method. The obtained products were characterized by X-ray diffraction analysis, field-emission scanning electron microscopy, Fourier-transform infrared spectroscopy, Raman spectrophotometry, X-ray photoelectron spectroscopy, and photoluminescence spectroscopy. The analytical results confirmed homogeneously distributed Ag nanoparticles supported on the surface of flower-like ZnO nanostructure. The photocatalytic effect of the heterostructure Ag/ZnO nanocomposites was investigated using photodegradation under ultraviolet (UV) light of methylene blue as model dye. The heterostructure Ag/ZnO nanocomposites exhibited much higher photocatalytic activity than pure ZnO flowers. The improved photocatalytic properties are attributed to formation of a Schottky barrier at the metal–semiconductor interface of the Ag/ZnO nanocomposites.     

Tailoring the charge carrier dynamics in ZnO nanowires: the role of surface hole/electron traps

Post-fabrication thermal-annealed ZnO nanowires (NWs) in an oxidizing (or a reducing) ambient were investigated using transient photoluminescence and X-ray photoelectron spectroscopy. Our findings reveal an ultrafast hole-transfer process to the surface adsorbed oxygen species (e.g., O(2)(-)) occurring within a few hundred picoseconds (ps) in the air-annealed samples; and an ultrafast electron-transfer process to charged oxygen vacancies (i.e., V(O)(2+)) occurring within tens of ps in the H(2)-annealed samples. Contrary to the common perception that the band edge emission (BE) dynamics are strongly influenced by the carrier trapping to the green emission related defect states (i.e., V(Zn)), these above processes compete effectively with the ZnO BE. Hole trapping by ionized V(Zn), which occurs in an ultrashort sub-ps-to-ps timescale (and hence limits its effective hole capture radius), however, has less influence on the BE dynamics. Importantly, our findings shed new light on the photoinduced charge transfer processes that underpins the novel properties of enhanced photocatalytic activity, photovoltaic performance, and photoconductivity response of ZnO NWs, thereby suggesting a strategy for tailoring the ultrafast carrier dynamics in ZnO NW-based devices.     

Ordered networks of ZnO-nanowire hierarchical urchin-like structures for improved dye-sensitized solar cells

Quasi-1D ZnO nanowires (NWs) ordered as patterned 3D hollow hierarchical urchin-like structures have been prepared on transparent conducting substrates by electrodeposition. The ZnO NWs have been grown on self-assembled ordered polystyrene microspheres with electrical charge densities ranging from 5 to 30 C cm(-2) and organized arrays of mono and multi-urchin layers have been built. These layers have been sensitized by the highly absorbing D149 indoline organic dye. The optical characterizations and dye titrations have shown a significant increase in the light scattering and absorption as well as dye loading for the organized structures compared to randomly vertically aligned ZnO NWs grown under the same conditions. The dye-sensitized solar cells (DSSC) prepared using the sensitized layers have been characterized by current-voltage (J-V) measurements, IPCE and by electrochemical impedance spectroscopy. We show that the best performances are obtained for the 3D urchin monolayer structures. The conversion efficiency is increased by up to 4 times compared to their counterparts made of randomly dispersed vertical ZnO NWs. Impedance spectroscopy results show a very fast charge transfer in the ZnO NWs and urchin monolayers and that the electron lifetime is in the 4-14 ms range.     

Enhanced UV photosensing properties of ZnO nanowires prepared by electrodeposition and atomic layer deposition

A new process enabling the synthesis of zinc oxide (ZnO) and Al-doped ZnO nanowires (NWs) for photosensing applications is reported. By combining atomic layer deposition (ALD) for the seed layer preparation and electrodeposition for the NW growth, high-quality ZnO nanomaterials were prepared and tested as ultraviolet (UV) sensors. The obtained NWs are grown as arrays perpendicular to the substrate surface and present diameters between 70 and 130 nm depending on the Al doping, as seen from scanning electron microscopy (SEM) studies. Their hexagonal microstructure has been determined using X-ray diffraction and Raman spectroscopy. An excellent performance in UV sensing has been observed for the ZnO NWs with low Al doping, and a maximal photoresponse current of 11.1 mA has been measured. In addition, initial studies on the stability have shown that the NW photoresponse currents are stable, even after ten UV on/off cycles.     

Photocatalytic oxidation of organic dyes with nanostructured zinc dioxide modified with silver metals

Silver-doped nano-ZnO samples with different Ag loadings were prepared by a one-spot solvothermal method. The structure, physico-chemical and optical properties of the products are characterized by using X-ray diffraction (XRD), transmission electron microscope (TEM), energy dispersive X-ray analysis (EDS), diffuse reflectance spectroscopy (DRS) and photoluminescence spectra (PL). The photocatalytic activity of the as-prepared samples was examined by using photocatalytic oxidation of methyl orange (MO) as a model reaction, and the effects of the noble metal content on the photocatalytic activity were investigated. The results indicated that the photocatalytic activity of ZnO nanoparticles can be greatly improved by depositing appropriate amount of noble metal on their surface as electron scavengers. In addition, a key mechanism was proposed in order to account for the enhanced activity. The enhancement for the photocatalytic activities can be attributed to the interaction between Ag particles and ZnO, which made Ag particles act as electron traps to effectively separate the excited electron-hole pairs.     

Synthesis and characterization of ZnO nanowires by thermal oxidation of Zn thin films at various temperatures

In this research high-quality zinc oxide (ZnO) nanowires have been synthesized by thermal oxidation of metallic Zn thin films. Metallic Zn films with thicknesses of 250 nm have been deposited on a glass substrate by the PVD technique. The deposited zinc thin films were oxidized in air at various temperatures ranging between 450 °C to 650 °C. Surface morphology, structural and optical properties of the ZnO nanowires were examined by scanning electron microscope (SEM), X-ray diffraction (XRD), energy dispersive X-ray (EDX) and photoluminescence (PL) measurements. XRD analysis demonstrated that the ZnO nanowires has a wurtzite structure with orientation of (002), and the nanowires prepared at 600 °C has a better crystalline quality than samples prepared at other temperatures. SEM results indicate that by increasing the oxidation temperature, the dimensions of the ZnO nanowires increase. The optimum temperature for synthesizing high density, ZnO nanowires was determined to be 600 °C. EDX results revealed that only Zn and O are present in the samples, indicating a pure ZnO composition. The PL spectra of as-synthesized nanowires exhibited a strong UV emission and a relatively weak green emission.     

Hierarchical saw-like ZnO nanobelt/ZnS nanowire heterostructures induced by polar surfaces

Saw-like nanostructures composed of single-crystalline ZnO nanobelts and single-crystalline ZnS nanowires have been successfully synthesized by a vapor-solid process. Several techniques, including scanning electron microscope, transmission electron microscopy, and photoluminescence spectroscopy, were used to investigate the structures, morphology, and photoluminescence properties of the products. Due to the similar crystal habits of wurtzite ZnO and ZnS with chemically active Zn-terminated (0001) and chemically inactive O-terminated (or S-terminated) (000) polar surfaces, hierarchical saw-like nanostructures were considered to be formed by the initiation of a chemically active Zn-terminated ZnO (0001) polar surface. Photoluminescence properties of the heterostructures, different from pure ZnO nanobelts or ZnS nanowires, were also studied at room temperature.     

Investigation of the growth parameters of hydrothermal ZnO nanowires for scale up applications

Zinc oxide nano-wires (ZnO NWs) are synthesized reproducibly with high yield via a low temperature hydrothermal technique. The influence of the growth duration time, growth temperature, zinc precursor and base concentration of Na₂CO₃ on the morphology of NWs is investigated. The growth products are characterised using scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). SEM analysis shows that the optimum growth temperature is 140 °C and finds that length and diameter of ZnO NWs have a relationship with growth duration time and base concentrations of Na₂CO₃. In addition, it is reported that a high (～90%) yield of ZnO NWs can be synthesised via using any of three different precursors: zinc chloride, zinc acetate and zinc nitrate. TEM and XRD results indicate the high purity and the single crystalline nature of the ZnO NWs. XPS confirms the absence of sodium contaminants on the surface and indicates a near flat band surface condition. PL shows a large visible band in the yellow part of the spectrum, and a small exciton emission peak, indicating a large defect concentration, which is reduced after annealing in air.     

Preparation and characterization of nanocomposite ZnO–Ag thin film containing nano-sized Ag particles: influence of preheating,annealing temperature and silver content on characteristics

Nanocomposite ZnO–Ag thin film containing nano-sized Ag particles have been grown on glass substrate by spin-coating technique using zinc acetate dihydrate as starting precursor in 2-propanol as solvent and monoethanolamine as stabilizer. Silver nanoparticles were added in the ZnO sol using silver nitrate dissolved in ethanol-acetonitrile. Their structural, electrical, crystalline size and optical properties were investigated as a function of preheating, annealing temperature and silver content. The results indicated that the crystalline phase was increased with increase of annealing temperature up to 550 °C at optimum preheating temperature of 275 °C. Thermal gravimetric differential thermal analysis results indicated that the decomposition of pure ZnO and nanocomposite ZnO–Ag precursors occurred at 225 and 234 °C, respectively with formation of ZnO wurtzite crystals. The scanning electron microscopy and atomic force microscopy revealed that the surface structure (the porosity and grain size) of the ZnO–Ag thin film (the film thickness is about 379 nm) was changed compared to pure ZnO thin film. The result of transmission electron microscopy showed that Ag particles were about 5 nm and ZnO particles 58 nm with uniform silver nanoclusters. Optical absorption results indicated that optical absorption of ZnO–Ag thin films decreased with increase of annealing temperature. Nanocomposite ZnO–Ag thin films with [Ag] = 0.068 M and [Ag] = 0.110 M showed an intense absorption band, whose maximum signals appear at 430 nm which is not present in pure ZnO thin films. The result of X-ray photoelectron spectroscopy revealed that the binding energy of Ag 3d_5/2 for ZnO–Ag shifts remarkably to the lower binding energy compared to the pure metallic Ag due to the interaction between Ag and ZnO.     

Structural,optical, electrical,and photocatalytic properties of manganese doped zinc oxide nanocrystals

Manganese-doped and undoped ZnO nanocrystals were synthesized via wet-chemical methods. The structure, physico-chemical, electrical and optical properties of the as-prepared products were characterized by using the X-ray diffraction (XRD), UV-vis diffuse reflectance spectroscopy (DRS), photoluminescence spectroscopy (PLS) and electrochemical impedance spectroscopy (EIS) techniques. The photocatalytic activity of Mn-doped ZnO nanocrystal (mixed phases) has been examined under the visible-irradiation by using photocatalytic oxidation of rhodamine B (RhB) dye as a model reaction, and compared with that of known system such as pure ZnO nanocrystal (single-phase). The results showed that Mn doped ZnO nanocrystals bleaches RhB much faster than undoped ZnO upon its exposure to the visible light. The enhancement of the photocatalytic activity was discussed as an effect due to the Mn doping in the Mn-doped ZnO semiconductors, which shifts the optical absorption edge to the visible region and alters the electron-hole pair separation conditions. These factors are responsible for the higher photocatalytic performance of Mn/ZnO composites.     

纳米Ag/ZnO光催化剂及其催化降解壬基酚聚氧乙烯醚性能

采用氨浸法制备了不同Ag负载量的纳米Ag/ZnO光催化剂,并用X射线衍射、比表面积测定、X射线光电子能谱和漫反射紫外-可见光谱测定了Ag/ZnO的晶型结构、比表面积、表面组成和光谱特征.以壬基酚聚氧乙烯醚(NPE-10)为模型污染物,分别在紫外光和可见光照射下考察了纳米Ag/ZnO的光催化活性.结果表明,Ag能成功地负载到ZnO表面,且随着Ag负载量的增加,ZnO的粒径逐渐增大,比表面积逐渐减小.与纳米ZnO样品相比,Ag/ZnO中Ag 3d5/2结合能减小,而Zn 2p和O 1s结合能增大,ZnO表面的羟基氧和吸附氧含量增加.当Ag负载量大于0.5%时,Ag/ZnO样品的吸收光谱发生红移,在可见光区出现吸收.光催化降解结果表明,0.5%Ag/ZnO样品的光催化活性最高,在紫外光和可见光照射3 h后NPE-10降解率分别约为77%和56%,而ZnO样品的光催化活性仅约为61%和40%.     

Synthesis and alignment of silver nanorods and nanowires and the formation of Pt, Pd, and core/shell structures by galvanic exchange directly on surfaces

Here we describe the synthesis of Ag nanorods (NRs) (aspect ratio <20) and nanowires (NWs) (aspect ratio > or =20) directly on surfaces by seed-mediated growth. The procedure involves attaching gold seed nanoparticles (Au NPs) to 3-mercaptopropyltrimethoxysilane (MPTMS)-functionalized silicon or glass surfaces and growing them into NRs/NWs by placing the substrates into a solution containing cetyltrimethylammonium bromide (CTAB), silver nitrate, and ascorbic acid with the pH ranging from 7 to 12. Under our conditions, Ag NRs/NWs grow optimally at pH 10.6 with a 3% yield, where spherical, triangular, and hexagonal nanostructures represent the other byproducts. The length of Ag NRs/NWs ranges from 50 nm to more than 10 microm, the aspect ratio (AR) ranges from 1.4 to >300, and the average diameter is approximately 35 nm. Approximately 40% of the 1D structures are NRs, and 60% are NWs as defined by their ARs. We also report the alignment of Ag NRs/NWs directly on surfaces by growing the structures on amine-functionalized Si(100) surfaces after an amidation reaction with acetic acid and a method to improve the percentage of Ag NRs/NWs on the surface by removing structures of other shapes with adhesive tape. Surface-grown Ag NRs/NWs also react with salts of palladium, platinum, and gold via galvanic exchange reactions to form high-surface-area 1D structures of the corresponding metal. The combination of the seed-mediated growth of Ag on Au NRs followed by the galvanic exchange of Ag with Pd leads to interesting core/shell NRs grown directly on surfaces. We used scanning electron microscopy, UV-vis spectroscopy, and X-ray photoelectron spectroscopy to characterize the surface-grown nanostructures.     

Enhanced visible-light-driven photocatalytic activities of 0D/1D heterojunction carbon quantum dot modified CdS nanowires

Zero-dimensional carbon dots (0D C-dots) and one-dimensional sulfide cadmium nanowires (1D CdS NWs) were prepared by microwave and solvothermal methods, respectively. A series of heterogeneous photocatalysts that consisted of 1D CdS NWs that were modified with 0D C-dots (C-dots/CdS NWs) were synthesized using chemical deposition methods. The mass fraction of C-dots to CdS NWs in these photocatalysts was varied. The photocatalysts were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and ultraviolet-visible spectroscopy. Their photocatalytic performance for the spitting of water and the degradation of rhodamine B (RhB) under visible light irradiation were investigated. The photocatalytic performance of the C-dots/CdS NWs was enhanced when compared with that of the pure CdS NWs, with the 0.4% C-dots/CdS NWs exhibiting the highest photocatalytic activity for the splitting of water and the degradation of RhB. The enhanced photocatalytic activity was attributed to a higher carrier density because of the heterojunction between the C-dots and CdS NWs. This heterojunction improved the electronic transmission capacity and promoted efficient separation of photogenerated electrons and holes.     

类石墨碳修饰提高ZnO纳米棒阵列光催化活性和光稳定性的研究

半导体光催化是一种理想的太阳能化学转化绿色技术,可以实现水分解制氢和CO2光还原制备碳氢化合物燃料.氧化锌 (ZnO) 作为一种直接带隙半导体材料,一方面具有性能优异、价格低廉、易制备等优点; 另一方面因光腐蚀而不稳定,大大限制了该材料的实际应用.本文提出了一种简单易行的类石墨碳修饰方法,可以有效提高 ZnO 用于CO2光还原的光催化活性和稳定性.首先采用水热法在金属锌片基底上生长 ZnO 纳米棒阵列 (ZnO-NRA),然后通过葡萄糖水热法进行不同含量的类石墨碳 (C-x) 修饰,形成 ZnO-NRA/C-x 纳米复合结构,同步实现碳包覆和碳掺杂.X 射线衍射结果表明,ZnO 纳米棒及ZnO-NRA/C-x 纳米复合结构都具有良好的纤锌矿型 (Wurtzite) 结构; 而拉曼散射则清楚地证实了类石墨碳的存在.扫描电子显微观察显示,生长的 ZnO 纳米棒长度大约 2-5 μm,直径为 400-700 nm,沿方向[0001]生长,端部由六个规则的 (103)晶面组成,进一步直观佐证了 ZnO 的典型纤锌矿型结构特征.透射电子显微分析结果表明,ZnO-NRA/C-x 纳米复合结构中类石墨碳包覆层厚度大约为 8 nm.ZnO-NRA/C-x 纳米复合结构的 X 射线光电子谱分析结果验证了 C-C,C-O 和 C=O键的存在与碳的包覆层相对应; 而 C-O-Zn键的出现则是由于碳在 ZnO 中掺杂所引起.从紫外-可见吸收谱上可观察到ZnO 的典型吸收带边位置约为 385 nm,而碳的包覆和掺杂导致 ZnO-NRA/C-x 纳米复合结构的吸收带边发生红移,并且吸收背底明显提高.电化学阻抗谱测试结果清楚地显示,ZnO-NRA/C-x 纳米复合结构比单纯 ZnO-NRA 的电化学阻抗明显降低,说明类石墨碳包覆层大幅度提高了电导性能,从而有利于光生载流子的分离和传输.荧光分析结果也表明,与单纯的 ZnO-NRA 相比,ZnO-NRA/C-x 纳米复合结构的荧光强度大幅度下降,进一步证实了 ZnO-NRA/C-x 纳米复合结构比单纯的 ZnO-NRA更有利于光生载流子的分离和传输.光电化学测试结果表明,ZnO-NRA/C-x 纳米复合结构的瞬态光电流 4 倍于单纯的ZnO-NRA,而 CO2 光还原性能测试也得到一致的结果.长时间多循环 CO2 光还原实验证实,ZnO-NRA/C-x 纳米复合结构具有稳定的光催化活性和极好的光稳定性.综上,我们利用一种简单易行的水热法进行类石墨碳修饰,成功开发了 ZnO-NRA/C-x 纳米复合结构,该结构因其优异的光生电子和空穴的分离和迁移性能,从而具有显著提升的CO2光还原活性和光稳定性.本工作证明,类石墨碳修饰是一种可以广泛借鉴的有效提升半导体材料光催化活性和光稳定性的可行方法.     

Ag/ZnO heterostructure nanocrystals: synthesis, characterization, and photocatalysis

A high yield of the dimer-type heterostructure of Ag/ZnO nanocrystals with different Ag contents is successfully prepared through a simple solvothermal method in the absence of surfactants. The samples are characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, UV-vis spectroscopy, and IR spectroscopy. The results show that all samples are composed of metallic Ag and ZnO; Ag nanoparticles locate on the surface of ZnO nanorods; the binding energy of Ag 3d(5/2) for the Ag/ZnO sample with a Ag content of 5.0 atom % shifts remarkably to the lower binding energy compared with the corresponding value of pure metallic Ag because of the interaction between Ag and ZnO nanocrystals; the concentration of oxygen vacancy for the as-synthesized samples varies with the increasing Ag content, and the Ag/ZnO sample with a Ag content of 5.0 atom % has the largest density of oxygen vacancy. In addition, the relationship between their structure and photocatalytic property is investigated in detail. It is found that the photocatalytic property is closely related to its structure, such as heterostructure, oxygen defect, and crystallinity. The presence of metallic Ag nanoparticles and oxygen vacancy on the surface of ZnO nanorods promotes the separation of photogenerated electron-hole pairs and thus enhances the photocatalytic activity.     

Synthesis and study of plasmon-induced carrier behavior at Ag/TiO2 nanowires

Nanocomposites of Ag/TiO(2) nanowires with enhanced photoelectrochemical performance have been prepared by a facile solvothermal synthesis of TiO(2) nanowires and subsequent photoreduction of Ag(+) ions to Ag nanoparticles (AgNPs) on the TiO(2) nanowires. The as-prepared nanocomposites exhibited significantly improved cathodic photocurrent responses under visible-light illumination, which is attributed to the local electric field enhancement of plasmon resonance effect near the TiO(2) surface rather than by the direct transfer of charge between the two materials. The visible-light-driven photocatalytic performance of these nanocomposites in the degradation of methylene blue dye was also studied, and the observed improvement in photocatalytic activity is associated with the extended light absorption range and efficient charge separation due to surface plasmon resonance effect of AgNPs.     

Characterization and field emission properties of ZnMgO nanowires fabricated by thermal evaporation process

In this paper, we investigate the roles of gold catalyst using modified thermal evaporation set-up in the growth process of ZnMgO nanowires. ZnMgO nanowires are fabricated on silicon substrates using different thickness of gold catalyst. A simple horizontal double-tube system along with chemical vapor diffusion of the precursors, based on Fick’s first law, is used to grow the ZnMgO nanowires. Field emission scanning electron microscopy images show that the ZnMgO nanowires are tapered. The optical properties of the ZnMgO nanowires are characterized by room temperature photoluminescence (PL) measurements. The PL studies demonstrate that the ZnMgO nanowires grown using this method have good crystallinity with excellent optical properties and have a larger band-gap in comparison to the pure ZnO nanowires. Field emission characterization shows that the turn-on field for the nanowires grown on the thinner gold film is lower than those grown on the thicker gold film.     

Effect of silver nanowires on the surface-enhanced Raman spectra (SERS) of the RNA bases

RNA bases have a great importance in the biological and genetics applications. The surface-enhanced Raman scattering (SERS) was used to study the orientation and adsorption structure of RNA bases adsorbed on the surface of silver nanowires (Ag NWs). The Ag NWs were prepared and its UV-vis spectra were recorded. The RNA bases oriented perpendicularly on the surface of Ag NWs, as the coverage area decreases. Consequently, the in-plane bands were enhanced according to the SERS selection rule. Many bands were red shifted due to the chemisorption of RNA bases on the Ag NWs surface. New bands corresponding to the base-surface bond were appeared in the SERS spectra.     

ZnO/Ag微米球的合成与光催化性能

用微波辅助多元醇法对预先制备的ZnO微米球进行修饰,合成了载银氧化锌微米球（ZnO/Ag）. 利用X射线衍射仪、场发射扫描电子显微镜、透射电子显微镜、X射线光电子能谱仪、紫外-可见双光束分光光度计和光致发光光谱仪等对样品的结构、形貌和光学性能进行了表征. 在紫外光照射下,通过亚甲基蓝的降解反应研究了样品的光催化活性. 结果表明,所制备的ZnO/Ag微米球是由面心立方的Ag纳米颗粒附着在纤锌矿结构的ZnO球表面形成;与ZnO相比,ZnO/Ag的紫外-可见光吸收光谱发生明显红移,在紫外和可见光范围均有较强的吸收;随着Ag含量的增加,ZnO/Ag荧光光谱强度先减弱后增强;与ZnO相比,ZnO/Ag的光催化活性明显提高,AgNO₃ 浓度为0.05 mol/L时制得的ZnO/Ag光催化活性最高.