Carbon dioxide reforming of methane over Ni/Mo/SBA-15-La2O3 catalyst: Its characterization and catalytic performance

The Ni/Mo/SBA-15 catalyst was modified by La2O3 in order to improve its thermal stability and carbon deposition resistance during the CO2 reforming of methane to syngas. The catalytic performance, thermal stability, structure, dispersion of nickel and carbon deposition of the modified and unmodified catalysts were comparatively investigated by many characterization techniques such as N2 adsorption, H2-TPR, CO2-TPD, XRD, FT-IR and SEM. It was found that the major role of La2O3 additive was to improve the pore structure and inhibit carbon deposition on the catalyst surface. The La2O3 modified Ni/Mo/SBA-15 catalyst possessed a mesoporous structure and high surface area. The high surface area of the La2O3 modified catalysts resulted in strong interaction between Ni and Mo-La, which improved the dispersion of Ni, and retarded the sintering of Ni during the CO2 reforming process. The reaction evaluation results also showed that the La2O3 modified Ni/Mo/SBA-15 catalysts exhibited high stability.     

Comparison of the quantity and reactivity of carbon deposit arising on Mo/Al2O3 and Mo/ZrO2 catalysts

The quantity and reactivity of carbon deposit arising on Mo/Al₂O₃ and Mo/ZrO₂ catalysts in propane decomposition was investigated. Results showed that the Mo/ZrO₂ catalyst is more resistant to carbon deposit formation process. The coke formed on the surface of this catalyst is more reactive in oxygen atmosphere than the carbon deposit formed under the same conditions on Mo/Al₂O₃. This revised version was published online in June 2006 with corrections to the Cover Date.     

Racemization of chiral amino alcohols III: Effect of Mg or Ca addition on the activity and stability of the Co/γ-Al2O3 catalyst

The racemization of R-(-)-2-amino-1-butanol in a reaction using Co/γ-Al₂O₃ catalysts and catalysts modified by Mg or Ca was investigated in this paper. Complete racemization was achieved with a yield of over 83% at using the Mg modified Co/γ-Al₂O₃ catalyst under optimized reaction conditions of 170°C and 2.5 MPa of H₂. The catalysts were thoroughly characterized by XRD, XPS, TPR, SEM and TEM. The addition of Mg and Ca may be advantageous for dispersing and stabilizing the active species of the Co/γ-Al₂O₃ catalyst, protecting from sintering, significantly improving its catalytic activity and stability.     

Influence of MgO in the CO2 – steam reforming of methane to syngas by NiO/MgO/ α-Al2O3 catalyst

Simultaneous steam and CO₂ reforming of methane to syngas (H₂and CO) over NiO/MgO/a-Al₂O₃ catalyst have been investigated at different MgO wt.%. The catalyst has been characterized by temperature-programmed reduction and XRD techniques. Addition of MgO reduced the carbon deposition and energy consumption. The stability and less coking on MgO-promoted catalysts are attributed to the lewis basicity of MgO.     

Effect of ceria loading on the carbon formation during low temperature methane steam reforming over a Ni/CeO2/ZrO2 catalyst

The characterization and catalytic activity of a Ni/CeO₂/ZrO₂ catalyst for methane steam reforming at 600°C were investigated. The addition of ceria increased the surface area and basicity of the catalysts. The redox reaction capability of the ceria increased the hydrogen yield and carbon monoxide selectivity, and inhibited carbon formation.     

The influence of La2O3 and TiO2 on NiO/MgO/α-Al2O3

Summary The effect of La₂O₃ and TiO₂ on product selectivity, methane conversion and coke formation over NiO/MgO/ α -Al₂O₃ catalyst were studied in a simultaneous steam and CO₂ reforming of methane to syngas. La₂O₃ and TiO₂ were added to the catalyst via incipient wetness impregnation and bulk precipitation techniques and catalyst activity was tested in a fixed bed quartz reactor. Results reveal that although the addition of these oxides has no effect on the product selectivity and methane conversion, but can reduce coke formation on the surface of the catalysts as it can enhance the mobility of lattice oxygen anions. The results further show that the catalysts prepared by bulk precipitation technique decrease the coke formation more effectively.     

Selective oxidation of octadecan-1-ol to octadecanoic acid over Co3O4/SiO2 catalysts

Factors (reaction temperature, reaction time, flow rate of oxygen, amount of catalyst, etc.) influencing the catalytic properties of Co₃O₄/SiO₂catalyst in the oxidation octadecan-1-ol to octadecanoic acid were investigated. The catalysts were characterized by means of XRD, FT-IR and N₂-adsorption. The experimental results indicate that under the optimal condition the selectivity to octadecanoic acid reached 97.5 % over 5 % Co₃O₄/SiO₂ catalyst.This revised version was published online in December 2005 with corrections to the Cover Date.     

Ce0.5Zr0.5O2修饰的Ni/SiC、Fe/SiC和Co/SiC催化燃烧甲烷性能

以铈锆固溶体（Ce_0.5Zr_0.5O₂）修饰的高比表面积SiC为载体,采用两步浸渍法制备了Ni、Fe和Co基催化剂,研究了其在煤层气催化燃烧脱氧中的催化活性和稳定性. 利用X射线衍射（XRD）、X射线光电子能谱（XPS）、电感耦合等离子体质谱（ICP-MS）、高分辨透射电子显微镜（HRTEM）、比表面积（BET）、热重分析（TGA）和H₂程序升温还原（H₂-TPR）对催化剂进行了表征. 分析结果表明,Ni、Fe和Co部分进入Ce_0.5Zr_0.5O₂固溶体晶格内部,导致催化剂体相形成更多的缺陷;同时Ce_0.5Zr_0.5O₂固溶体有助于加速金属氧化物和金属之间氧化还原过程的进行,促进了氧吸附、传输和对甲烷的活化. 另外,SiC和Ce_0.5Zr_0.5O₂固熔体良好的抗积碳性能,有效避免了催化剂在富甲烷反应气氛中因积碳而失活,从而使三种催化剂均具有优良的催化燃烧脱氧活性和稳定性. 其中,Co/Ce_0.5Zr_0.5O₂/SiC活性最高,可在320 ℃活化催化甲烷,并在410 ℃实现完全脱氧.     

Monolith Manganese-Based Catalyst Supported on ZrO2-TiO2 for NH3-SCR Reaction at Low Temperature

Monolith catalysts were prepared using TiO₂ and ZrO₂-TiO₂ as supports with MnO₂ as active component and Fe₂O₃ as promoter. The catalytic activities at low temperature and stability at high temperature for selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) in the presence of excessive O₂ were studied after the catalysts calcined at different temperatures. The catalysts were characterized by X-ray diffraction (XRD), specific surface area measurements (BET), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results indicated that the catalyst supported on ZrO₂-TiO₂ had excellent stability at high temperature, and possessed high specific surface area and oxygen storage capacity, and had strong redox property. The results of the catalytic activities indicated that the monolith manganese-based catalyst using ZrO₂-TiO₂ as support had evidently improved the activity of NH₃-SCR reduction reaction at low temperature, and it showed great potential for practical application.     

MnOx/MWCNTs低温氨选择性催化还原NOx硫中毒机理

以经过浓硝酸和等离子体放电预处理后的多壁碳纳米管(MWCNTs)为载体, 锰氧化物(MnO_x)为活性组分, 采用等体积浸渍法制备MnO_x/MWCNTs 催化剂. 利用热重分析(TGA)、扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)、程序升温还原/脱附(TPR/TPD)以及傅里叶变换红外(FTIR)光谱对催化剂进行表征, 探讨SO₂对催化剂低温氨选择性催化还原(SCR)NO_x活性的影响及SO₂中毒机理. 结果表明, 低温下SO₂对MnO_x/MWCNTs 催化剂活性有明显毒化作用. 反应温度越高, SO₂浓度越大, 催化剂SCR活性下降越快. 活性中心Mn原子硫酸化是催化剂失活的主要原因. 另外, 催化剂表面生成硫酸铵盐以及SO₂对NO吸附的抑制作用也一定程度上造成了催化剂的失活.     

氮掺杂MnCo2O4/N-KB的制备及氧还原催化性能

以Mn(Ac)_2和Co(Ac)_2作为前驱体,导电碳Ketjenblack (KB)作为负载碳源,采用水解-水热法制备氮掺杂的MnCo_2O_4/N-KB催化剂材料,对其结构特征和碱性溶液中氧还原反应的催化性能进行表征,并进一步分析其氧还原反应活性。结果表明:MnCo_2O_4/N-KB催化剂的形态是KB骨架上生长纳米级MnCo_2O_4,并且在N-KB和MnCo_2O_4之间形成化学耦合,产生协同作用,有效提高了MnCo_2O_4/N-KB催化剂的氧还原活性。MnCo_2O_4与N-KB的质量比为1∶9时,MnCo_2O_4/N-KB催化剂在O_2饱和0.1mol·L~(-1)KOH溶液中对氧还原反应的电催化性能最佳,反应的极限电流密度为5.7 mA·cm~(-2),半波电位接近0.81 V,电子转移数为4。在相同负载量下,MnCo_2O_4/N-KB催化剂相比商用Pt/C(电流密度5.2 mA·cm~(-2),半波电位0.83 V)有着更高的极限电流密度和耐久性。     

The Catalytic Dehydrogenation of c2h6 to c2h4 under non-Oxidative Conditions over the 6cr/g-al2o3Catalyst

In the present paper, the catalytic dehydrogenation of C₂H₆ to C₂H₄ under non-oxidative conditions was investigated in a fixed-bed micro-reactor under ambient pressure at 823 - 923 K. The 6Cr/g-Al₂O₃ catalyst was found to be the best catalyst among the g-Al₂O₃, SiO₂, MCM41, MgO and Si-2 supported chromium oxide catalysts. The features of the 6Cr/g-Al₂O₃ catalyst for the reaction could be listed as follows: (1) At 823 - 923 K, the C₂H₄ selectivity of 92.5-78.6% at a C₂H₆ conversion of 9.5-29.8% could be obtained. (2) The catalyst had the good regeneration performance, i.e., could be regenerated by air repeatedly. (3) The main products were C₂H₄, CH₄, H₂ and coke. No carbon oxides were identified.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

甲烷在Ni/TiO2催化剂表面的活化

考察了Ni/TiO2催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以TiO2为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对H2的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性.采用脉冲-质谱在线分析等技术,在无气相氧条件下向Ni/TiO2催化剂脉冲CH4,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关.CH4与Ni/TiO2催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ni/TiO2催化剂具有良好的反应活性和抗积碳性能.     

CH4-CO2 reforming to syngas over Pt-CeO2-ZrO2/MgO catalysts: Modification of support using ion exchange resin method

Pt-CeO2-ZrO2/MgO (Pt-CZ/MgO) catalysts with 0.8 wt% Pt, 3.0 wt% CeO2 and 3.0 wt% ZrO2 were prepared by wet impregnation method. Support MgO was obtained using ion exchange resin method or using commercial MgO. XRD, BET, SEM, TEM, DTA-TG and CO2-TPD were used to characterize the catalysts. CH4-CO2 reforming to synthesis gas (syngas) was performed to test the catalytic behavior of the catalysts. The catalyst Pt-CZ/MgO-IE(D) prepared using ion exchange resin exhibits more regular structure, smaller and more unique particle sizes, and stronger basicity than the catalyst Pt-CZ/MgO prepared from commercial MgO. At 1073 K and atmospheric pressure, Pt-CZ/MgO-IE(D) catalyst has a higher activity and greater stability than Pt-CZ/MgO catalyst for CH4-CO2 reforming reaction at high gas hourly space velocity of 36000 mL/(g·h) with a stoichiometric feed of CH4 and CO2. Activity measurement and characterization results demonstrate that modification of the support using ion exchange resin method can promote the surface structural property and stability, therefore enhancing the activity and stability for CH4-CO2 reforming reaction.     

A study on methanol steam reforming to CO2 and H2 over the La2CuO4 nanofiber catalyst

The La₂CuO₄ crystal nanofibers were prepared by using single-walled carbon nanotubes as templates under mild hydrothermal conditions. The steam reforming of methanol (SRM) to CO₂ and H₂ over such nanofiber catalysts was studied. At the low temperature of 150 °C and steam/methanol=1.3, methanol was completely (100%, 13.8 g/h g catalyst) converted to hydrogen and CO₂ without the generation of CO. Within the 60 h catalyst lifespan test, methanol conversion was maintained at 98.6% (13.6 g/h g catalyst) and with 100% CO₂ selectivity. In the meantime, for distinguishing the advantage of nanoscale catalyst, the La₂CuO₄ bulk powder was prepared and tested for the SRM reaction for comparison. Compared with the La₂CuO₄ nanofiber, the bulk powder La₂CuO₄ showed worse catalytic activity for the SRM reaction. The 100% conversion of methanol was achieved at the temperature of 400 °C, with the products being H₂ and CO₂ together with CO. The catalytic activity in terms of methanol conversion dropped to 88.7% (12.2 g/h g catalyst) in 60 h. The reduction temperature for nanofiber La₂CuO₄ was much lower than that for the La₂CuO₄ bulk powder. The nanofibers were of higher specific surface area (105.0 m²/g), metal copper area and copper dispersion. The in situ FTIR and EPR experiments were employed to study the catalysts and catalytic process. In the nanofiber catalyst, there were oxygen vacancies. H₂-reduction resulted in the generation of trapped electrons [e] on the vacancy sites. Over the nanofiber catalyst, the intermediate H₂CO/HCO was stable and was reformed to CO₂ and H₂ by steam rather than being decomposed directly to CO and H₂. Over the bulk counterpart, apart from the direct decomposition of H₂CO/HCO to CO and H₂, the intermediate H₂COO might go through two decomposition ways: H₂COO=CO+H₂O and H₂COO=CO₂+H₂.     

热处理温度对锂氧气电池用Co-N/C催化剂催化性能的影响

开发低成本、高效的空气电极催化剂是发展锂空气电池的关键课题之一. 采用邻菲咯啉(phen)为配体制备Co(phen)₂配合物,负载于BP2000 碳载体上,并分别在600、700、800 和900 ℃的温度下进行热处理,制备得到碳支撑的Co-N催化剂(Co-N/C). 对催化剂的氧还原反应/析氧反应(ORR/OER)活性进行了表征,并且与典型的CoTMPP/C催化剂进行了比较. 同时研究了煅烧温度对Co-N/C催化剂的组成和结构的影响. 电化学测试结果表明,热处理温度为700-800 ℃时催化剂具有较好的电化学性能. Co-N/C催化剂具有电化学性能优良与低成本的特点,是一种良好的锂氧气电池催化剂.     

Combination of CO2 reforming and partial oxidation of CH4 over Ni/Al2O3 catalysts using fluidized bed reactor

The effects of the Ni loading, total feed flow rate, prereduction temperature, reaction temperature and feed gas ratio for combination of CO₂ reforming and partial oxidation of CH₄ over Ni/Al₂O₃ were investigated using a fluidized bed reactor. Methane conversion to syngas was drastically enhanced using a fluidized bed reactor over Ni/Al₂O₃ catalyst calcined at high temperature. The fluidized bed and the fixed bed reactor were compared and a promoting mechanism of the fluidized bed reactor was proposed. This revised version was published online in August 2006 with corrections to the Cover Date.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.