Comparative study of capillary zone electrophoresis and micellar electrokinetic chromatography for the separation of twelve aromatic sulphonate compounds

Summary Two modes of capillary electrophoresis (CE), capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC), were investigated for the separation of 12 aromatic sulphonate compounds. In CZE, although the voltage applied, the buffer concentration and the pH were optimized for effective separation of the compounds studied, under the best conditions four of the five amino compounds coeluted, as did naphthalene-1-sulphonic acid and naphthalene-2-sulphonic acid. In MEKC, sodium dodecyl sulphate (SDS) and Brij 35 were chosen as the anionic and nonionic surfactants and the effect of the concentration of micelles was examined. The effect of adding methanol as the organic modifier was also investigated with each of these micellar systems. All the analytes, including the isomers, were completely separated by use of MEKC with Brij 35 but when SDS was used only 11 compounds were separated because two amino compounds coeluted.     

Cationic double-chained surfactant as pseudostationary phase in micellar electrokinetic capillary chromatography for drug separations

The cationic double-chained surfactant didodecyldimethylammonium bromide (DDAB) was used as pseudostationary phase (PSP) in micellar electrokinetic capillary chromatography (MEKC). Its performance on the three kinds of drugs, i.e., basic, acidic, and neutral drugs, was systematically investigated. Nicotine, cotinine, caffeine, lidocaine, and procaine were selected as the model basic drugs. Good baseline separation and high efficiency were obtained under the optimal separation condition that consisted of 50mM phosphate (pH 4.0) and 0.08 mM DDAB. Three basic phenylenediamine isomers can also be well separated with DDAB in buffer. In addition, DDAB can form cationic bilayer on the capillary wall, thus the wall adsorption of basic analytes was greatly suppressed. Compared with commonly used CTAB, the separation of basic drugs was significantly improved with a much lower amount of DDAB present in the buffer. The DDAB-involved MEKC also showed superiority to CTAB upon the separation of acidic drugs, amoxicillin and ampicillin. In the case of neutral compounds, a good separation of resorcinol, 1-naphthol and 2-naphthol was achieved with 0.1mM DDAB and 30% (v/v) acetonitrile (ACN) present in buffer. Hence, it was concluded that the double-chained cationic surfactant DDAB can be a good substitute for traditional single-chained surfactant CTAB in MEKC.     

Achiral and chiral separations using MEKC,polyelectrolyte multilayer coatings,and mixed mode separation techniques with molecular micelles

Mixed mode (MM) separation using a combination of MEKC and polyelectrolyte multilayer (PEM) coatings is herein reported for the separation of achiral and chiral analytes. Many analytes are difficult to separate by MEKC and PEM coatings alone. Therefore, the implementation of a MM separation provides several advantages for overcoming the limitations of these well‐established methods. In this study, it was observed that achiral separations using MEKC and PEM coatings individually resulted in partial resolution of eight very similar aryl ketones when the molecular micelle (sodium poly(N‐undecanoyl‐L ‐glycinate)) concentration was varied from 0.25 to 1.00% w/v and the bilayer number varied from 2 to 4. However, when MM separation was introduced, baseline resolution was achieved for all eight analytes. In the case of chiral separations, temazepam, aminoglutethimide, benzoin, benzoin methyl ether, and coumachlor were separated using the three separation techniques. For chiral separations, the chiral molecular micelle, sodium poly(N‐undecanoyl‐L ‐leucylvalinate), was employed at concentrations of 0.25–1.50% w/v for both MEKC and PEM coatings. Overall, the results revealed partial separation with MEKC and PEM coatings individually. However, MM separation enabled baseline separation of each chiral mixture. The separation of achiral and chiral compounds from different compound classes demonstrates the versatility of this MM approach.     

Optimization of the separation of flavonoids by micellar electrokinetic capillary chromatography: Effect of organic solvents

Summary A group of flavonoids of special interest to wine quality were separated by micellar electrokinetic chromatography (MEKC) with diode array detection. Their separation was optimized as a function of the buffer concentration and pH, the concentration of sodium dodecyl sulfate (SDS) and the applied voltage. Selectivity and resolution of the solutes were increased by adding organic solvents to the separation buffer, the best results being obtained at lower concentrations. An optimized buffer with 5% methanol provided optimum separation with regard to efficiency, resolution and migration time. The optimized method was applied to the determination of these compounds in wine samples.     

Control of separation selectivity in micellar electrokinetic chromatography by modification of the micellar phase with solubilized organic compounds

On the basis of the data on the distribution of various neutral solutes between sodium dodecyl sulfate (SDS) micelles and water, the control of separation selectivity in micellar electrokinetic chromatography (MEKC) by modification of the micellar phase with organic additives has been proposed and applied to the separation of simple model compounds. It was found that the distribution constants between the micelles and water (K_d,mc), which were determined by means of MEKC, of the solutes possessing hydrophilic functional groups are much larger than those between heptane and water (K_d,hep), whereas the K_d,mc values of the solutes possessing no hydropholic groups are comparable to their K_d,hep values. This indicates that the former solutes are preferentially solubilized in the Stern layer of the micelles and that the latter are located in the hydrocarbon core. In MEKC separations of aromatic compounds and metal acetylacetonates, considerable changes in separation selectivity were caused by the addition of compounds possessing both hydrophilic functional groups such as alcohols, phenol and ketones to the SDS micellar solution. The variations of the retention factors of the analytes could be explained in terms of saturation of the solubilization sites in the Stern layer with the modifiers, specific interaction of the modifiers with the analytes via hydrogen bonding in the micelles, and expansion of the core volume with the hydrocarbon parts of the modifiers. Such effects of the micellar modification could improve the resolution as well as the selectivity of MEKC separations.     

Simultaneous analysis of cationic, anionic, and neutral compounds using monolithic CEC columns

A new capillary electrochromatography (CEC) column for the simultaneous analysis of cationic, neutral, and anionic compounds using CEC-ESI-MS is described. Three different silica monolith columns were prepared by changing the poly(ethylene glycol) (PEG) contents for comparison of the separation property of these columns. Different separation programs were used for the simultaneous separation of different charged compounds under the same conditions. The column prepared with 80 mg of PEG separated typical compounds within 15 min using 1 M formic acid as the electrolyte. The analytes migrated in the order of cationic, neutral, and anionic compounds, which means that the migration order was mainly determined by the electrophoresis. The hydrodynamic flow by pressure from the inlet side was significant for a stable analysis to be achieved. The effect of the composition of the sheath liquid was also examined. All analytes (14 amino acids, thiourea, urea, citric acid, and ATP) were detectable when 1% acetic acid in 50% (v/v) methanol was used as the sheath liquid.     

Nonaqueous media for separation of nonionic organic compounds by capillary electrophoresis

For the separation of neutral compounds by micellar electrokinetic chromatography, separations are usually carried out in predominantly aqueous solution in order to preserve the charged micelle necessary for the separation. We now show that polycyclic aromatic hydrocarbon (PAH) compounds can be separated efficiently by capillary electrophoresis in pure methanol or in aqueous-organic mixtures containing a high percentage of methanol. Sodium tetradecyl sulfate was the preferred surfactant. The effects of pH, solvent composition, surfactant structure, and surfactant concentration on the separations were studied. Reproducible migration times and linear calibration plots were obtained.     

Separation of hydrophobic solutes by organic-solvent-based micellar electrokinetic chromatography using cation surfactants

In this study, the separation of 13 homologous stick-like hydrophobic solutes, i.e., biphenyl nitrile derivatives, by organic-solvent-based micellar electrokinetic chromatography (MEKC) was investigated in terms of separation medium composition, species and concentration of surfactant, other additives, separation voltage and temperature. The results showed that the 13 strong hydrophobic compounds were baseline separated in 25 min with a repeatability of less than 1.3% (RSD) for migration time. The separation medium was a mixture of methanol, 2-propanol and water (58.5:10:31.5), containing 150 mM cetyltrimethylammonium bromide (CTAB) and 20 mM sodium borate. Variety of solvent composition, temperature and applied voltage all showed remarkable effect on the separation. The organic-solvent-based MEKC method proved to be superior to the aqueous MEKC and microemulsion electrokinetic chromatography (MEEKC) methods for the separation of strongly hydrophobic compounds.     

Investigation of solvent effects in capillary electrophoresis for the separation of biological porphyrin methyl esters

The effects of organic solvents on the capillary electrophoresis (CE) separation of a number of important biological porphyrin methyl esters - six weakly basic, hydrophobic cyclic tetrapyrroles possessing two and four to eight methyl ester groups around the periphery of the porphyrin ring - were investigated in the mode of micellar electrokinetic chromatography (MEKC), microemulsion electrokinetic chromatography (MEEKC), and nonaqueous CE. In aqueous MEKC, partial separation of the six neutral porphyrin methyl esters was obtained with an organic modifier (acetonitrile) in the concentration range between 20 and 40%, in which sodium dodecyl sulfate (SDS) molecules might be present in the form of SDS micelles and/or SDS micelle-like aggregates. Relatively stable SDS micelles can be formed in nonaqueous MEKC using formamide as the separation medium, but the separation of the target analytes remained unsatisfactory. Improved resolution of all six porphyrin methyl esters was obtained using MEEKC with the running buffer consisting of 0.8% w/w n-heptane (oil phase), 2.25% w/w SDS and 1.0% w/w Brij 35 (mixed surfactant), 6.6% w/w 1-butanol (cosurfactant), and 30% v/v 2-propanol (second cosurfactant), but reproducibility in terms of peak areas for certain porphyrins (especially uroporphyrin I octamethyl ester) was found to be very poor. Best separation performances were achieved with nonaqueous CE separations in which the weakly basic porphyrin methyl esters were protonated under strongly acidic conditions (e.g., using 10 mM perchloric acid) in mixed organic solvents. For example, using a 50:50 mixture of methanol and acetonitrile as the separation medium, baseline separation of all six (positively charged) porphyrin methyl esters can be obtained within 3 min and the average precision (RSD, N = 13) in terms of migration time and peak area were 0.55 and 2.16%, respectively.     

Twenty-five years of micellar electrokinetic chromatography

Micellar electrokinetic chromatography (MEKC), which can separate neutral analytes as well as charged analytes by the capillary electrophoretic technique, was developed in 1982 and the first paper was published in 1984. The authors’ group concentrated their effort into the characterization of MEKC as a separation technique until early 1990s. Most issues in MEKC separations were successfully solved and wide applicability of MEKC was verified in 1990s. In particular, sweeping, an on-line sample preconcentration technique, was very successful for the concentration of neutral analyte as well as ionic ones. In this paper, our studies on MEKC will be summarized from the personal viewpoint of the author.     

Determination of the herbicide metribuzin and its major conversion products in soil by micellar electrokinetic chromatography

In this paper, a multiresidue method for the analysis in soils of metribuzin (M) and its major conversion products, deaminometribuzin (DA), diketometribuzin (DK) and deaminodiketometribuzin (DADK) is developed. Considering the neutral and charged nature of the molecules, micellar electrokinetic chromatography (MEKC) is a very efficient method for the separation of these compounds, providing high efficiency and short analysis times. Different electrophoretic parameters were studied to optimize the separation, such as the buffer pH and concentration, sodium dodecyl sulphate (SDS) concentration, injection conditions and applied voltage. Excellent separation of the studied compounds was achieved within about 7 min. Soil samples were previously extracted using methanol in an ultrasonic bath and then a SPE procedure was applied to pre-concentrate the analytes by passage through a LiChrolut EN sorbent column. Detection limits at the low microgkg(-1) level were obtained. The proposed method has been satisfactorily applied in soil samples showing recoveries ranging from 86.7% to 104.2% and represents a valuable alternative to high-performance liquid chromatography (HPLC).     

非水胶束电动色谱分离邻苯二甲酸酯类化合物

非水胶束电动色谱(NAMEKC)兼具非水毛细管电泳的优点和胶束电动色谱的分离机制,尤其适于对强疏水性化合物进行分离分析。在以甲酰胺为非水溶剂的电泳介质中,采用十二烷基硫酸钠（SDS）形成胶束相,开展NAMEKC方法的研究。通过添加水溶液、调节水溶液酸度、添加有机溶剂、改变SDS浓度等操作条件的考察,在15 min 内实现了3种美国环保局优先监测的污染物——邻苯二甲酸二甲酯、邻苯二甲酸二乙酯、邻苯二甲酸二丁酯的分离。分离度最小者为1.5,检测限优于3.04 mmol/L(以信噪比为3计)。3种典型的强疏水性物质的成功分离,显示出NAMEKC方法在分离疏水性物质方面的优势,扩展了NAMEKC在电中性有机物分析中的应用。     

Solute-solvent interactions in micellar electrokinetic chromatography: V. Factors that produce peak splitting

The experimental conditions that produce analyte peak splitting in micellar electrokinetic capillary chromatography (MEKC) have been systematically investigated. The system studied was a neutral phosphate buffer and sodium dodecyl sulfate (SDS) micelles as pseudostationary phase. A number of analytes showing a wide variety of hydrophobicity values and several organic solvents as sample diluents have been tested. Peak splitting phenomena are mainly due to the presence of organic solvent in the sample solution. They increase with the hydrophobicity of the analyte and decrease with the increase of the surfactant concentration. When hydrophobic compounds are analyzed the suggested ways to avoid split peaks are: (i) the use of 1-propanol or 1-butanol as sample diluent instead of methanol or acetonitrile or (ii) the use of high concentration of surfactant in the separating solution when the analyte must be dissolved in pure methanol or acetonitrile.     

Highly-sensitive micellar electrokinetic chromatographic analysis of dioxin-related compounds using on-line concentration.

An application study of an on-line concentration technique of neutral analytes for micellar electrokinetic chromatography (MEKC) was carried out in environmental analysis to enhance the UV detection sensitivity. Several dioxins and related compounds, such as dibenzofuran, dibenzo-p-dioxin, 2,3- and 2,7-dichlorodibenzo-p-dioxins, and 2,3,7-trichlorodibenzo-p-dioxin, were used as test solutes. For a highly sensitive separation and detection, cyclodextrin-modified MEKC (CD-MEKC) under acidic conditions was employed as a separation mode and stacking using reverse migrating micelles and a water plug (SRW) as an on-line concentration technique. Almost a 200-fold gain in detection sensitivity was obtained for the model compounds in SRW-CD-MEKC compared to that in normal CD-MEKC without on-line concentration and the limit of detection was found to be around 0.1 ppm for each solute.     

Solid-phase extraction and sample stacking-micellar electrokinetic capillary chromatography for the determination of multiresidues of herbicides and metabolites

Micellar electrokinetic capillary chromatography (MEKC) with diode array detection was used for the separation of 13 compounds (eight herbicides widely used in agriculture: metribuzin, lenacil, ethofumesate, atrazine, terbutryn, isoproturon, chlorotoluron and linuron, and five of their principal degradation products; namely, deethylatrazine, 2-hydroxyatrazine, deethyl-2-hydroxyatrazine, deisopropylatrazine and 3-chloro-4-methylphenylurea). Peak separation for the 13 analytes was not successful when a single surfactant system was employed, neither sodium dodecyl sulfate (SDS) nor dioctyl sulfosuccinate (DOSS) sodium salt. However, a mixture of these herbicides was successfully separated using a mixed micellar system involving SDS–DOSS in less than 14 min. An application study of an on-line concentration technique for MEKC was carried out to enhance sensitivity. The optimized on-line stacking procedure consisted simply of the addition of 50 mM of sodium chloride to the injection sample, the stacking effect being more intensive as analyte polarity increased. When this stacking procedure was combined with an off-line sample preconcentration step, based on solid-phase extraction, analytes could be detected in the ppb range. The whole method was applied to ultra-high-quality and natural waters. Linear relationships between the analytical signal and the initial analyte concentration were found to be independent of the type of water, except for the more polar analytes for which small differences were observed.     

Determination of polyphenol components in herbal medicines by micellar electrokinetic capillary chromatography with Tween 20

A simple and convenient method of micellar electrokinetic capillary chromatography (MEKC) using polyoxyethylene sorbitan monolaurate (Tween 20) to form single micelle and methanol as a buffer additive was introduced for the simultaneous determination of five polyphenols, including scopoletin, rutin, esculetin, chlorogenic acid and caffeic acid. A running buffer solution of pH 9.3, 20 mmol/L sodium tetraborate containing 64 mmol/L Tween 20 and 9% (v/v) methanol was adopted in the separation. Because rutin and esculetin were difficult to be separated by capillary zone electrophoresis (CZE) and SDS-based MEKC, Tween 20-based MEKC was adopted and the polyphenols were separated satisfactorily. The proposed method was used to determine the polyphenol components in the herbal medicine of Cortex fraxini. The separation mechanism of Tween 20-based MEKC for the polyphenols was discussed preliminarily.     

Micellar electrokinetic chromatography - From theoretical concepts to real samples (Review)

Micellar electrokinetic chromatography (MEKC) is an alternative to liquid chromatographic separations. It is a highly efficient separation technique that is performed with the same experimental set-up as is used for capillary electrophoresis (CE), thus extending the applicability of CE to neutral solutes. MEKC can be regarded as a separation technique with a similar scope to that of reversed-phase high-performance liquid chromatography (RP-HPLC), having advantages over HPLC with regard to the efficiency of the separation system, separation speed, cost, and tolerance to matrix constituents. This paper discusses the applicability of MEKC to real samples and also addresses developments widening the scope of this emerging technique: on-line concentration by stacking or sweeping and sensitive detection schemes.     

Analysis of carbamate pesticides by micellar electrokinetic chromatography

Capillary elcctrophoresis (CE) was used for the qualitative and quantitative analysis of eleven compounds of the carbamate, thio-carhamate, and dithiocarbamate classes of pesticides. Micellar elec-trokinetic chromatography (MEKC) was employed for the separation of these substances. The analysis was performed using an uncoated fused silica column, in borate buffer containing SDS and 10% methanol at basic pH, and UV detection at 230 nm. The addition of methanol to the buffer increased the separation and affected intrinsic migration of analytes. The working standard solutions were prepared in acetonitrile/water 50:50. Although these compounds are structurally different, with a large spectrum of chemical properties, such as polarity and solubility, good separation and sensitivity were obtained. Moreover, good recovery of car-bamates was obtained from tap-water using a styrene-divinylben-zene polymer column with the solid phase extraction (SPE) technique.     

Analysis of organic components of smokeless gunpowders: high-performance liquid chromatogaphy vs. micellar electrokinetic capillary chromatography

The aim of the present study was to verify the analytical performances of high-performance liquid chromatography (HPLC) and micellar electrokinetic capillary chromatography (MEKC) for the separation and qualitative determination of a selected group of organic components of smokeless gunpowders. The HPLC method was based on a gradient reversed-phase elution with a mobile phase composed of 0.17 M H(3)PO(4)/methanol; detection was performed by UV absorption at the wavelengths of 220, 254, and 270 nm. The MEKC experiments were carried out by using uncoated fused-silica capillaries (50 microm inside diameter, 50 cm effective length) and a running buffer composed of 10 mM sodium tetraborate at pH 9.24 added with 25 mM sodium dodecyl sulfate (SDS); the applied voltage was 25 kV; detection was either at a fixed wavelength UV of 214 nm or with a diode-array detector operating in the wavelength range from 190 to 350 nm. Both reversed-phase HPLC and MEKC techniques succeeded in resolving the tested standard mixtures of organic components of smokeless powders. Although the sequence of elution of the different analytes was slightly different between HPLC and MEKC, a statistical analysis based on the Spearman's rank correlation test showed that the two separation patterns were highly correlated. HPLC and MEKC were comparable in terms of elution/migration time precision, whereas MEKC showed higher reproducibility of peak areas. The interfacing of capillary electrophoresis with diode array UV detection provided distinct UV spectra of the individual analytes, thus improving, on the detection side, the analytical selectivity and identification power of capillary electrophoresis.     

Use of multivariate analysis for optimization of separation parameters and prediction of migration time, resolution, and resolution per unit time in micellar electrokinetic chromatography

The optimization of separation parameters in chromatography for better separation and resolution of analytes continues to be a labor intensive procedure usually performed by a trial and error method. A multivariate analysis in the form of multilinear regression (MLR) is used to optimize separation parameters and predict the migration behavior, resolution, and resolution per unit time of achiral (4-chlorophenol, pentachlorophenol, clonazepam, and diazepam) and chiral (1,1'-binaphthyl 2,2'-dihydrogen phosphate (BNP), and 1,1'-bi-2-naphthol (BOH)) compounds in MEKC. Separations of achiral and chiral analytes were performed using an achiral (poly(sodium N-undecylenic sulfate)) molecular micelle and chiral (poly(sodium N-undecanoyl-L-leucylvalinate) or poly(sodium N-undecanoyl-L-isoleucylvalinate)) molecular micelle, respectively, at various operating temperatures, applied voltages, pH values, and molecular micelle concentrations in the BGE. The separation parameters were subsequently used as input variables for MLR models. The models were validated with independent samples. The root-mean-square percent relative error (RMS%RE) is used as a figure of merit for characterizing the performance of the migration time, resolution, and resolution per unit time models. The RMS%RE obtained for predicted migrated times, resolutions, and resolution per unit time of 4-chlorophenol, pentachlorophenol, clonazepam, diazepam, BNP, and BOH ranged between 8 and 19%. The same experimental procedure was used to optimize the separation parameters of six other chiral analytes of different compound class. The predicted migration times, resolutions, and resolution per unit time of the chiral as well as the achiral analytes compare favorably with the experimental migration times and resolutions, indicating versatility and wide applicability of the technique in MEKC.