Investigation of hydrothermal routes to mixed-metal cerium titanium oxides and metal oxidation state assignment using XANES

The reaction between TiF(3) or TiO(2) and Ce(3+) in sodium hydroxide solutions yields highly crystalline NaCeTi(2)O(6) at room temperature and under mild hydrothermal conditions (T < or = 240 degrees C). There is no evidence for the formation of ternary Ce-Ti-O materials by this method, and the use of bases other than NaOH always produces poorly crystalline materials. The material NaCeTi(2)O(6) has a distorted perovskite structure with sodium and cerium ions randomly occupying the A sites: Pnma, a = 5.4517(8) A, b = 7.7292(6) A, c =5.4573(3) A. XANES spectroscopy at the Ti K edge and Ce L(III) edge, with reference to crystalline model compounds, reveals that cerium is found solely as Ce(III) and titanium as Ti(IV) in NaCeTi(2)O(6). Isomorphous substitution of Ce(3+) by Nd(3+) or Ti(4+) by V(4+) is found to be very facile under hydrothermal conditions (at a temperature of 240 degrees C), by addition of appropriate amounts of metal salts to the hydrothermal reaction mixtures. The series NaCe(1-x)Nd(x)Ti2O6 (0 < or = x < or = 1) and NaCeTi(2-x)V(x)O6 (0 相似文献   

Defect chemistry, surface structures, and lithium insertion in anatase TiO2

Atomistic simulation techniques are used to investigate the defect properties of anatase TiO(2) and Li(x)TiO(2) both in the bulk and at the surfaces. Interatomic potential parameters are derived that reproduce the lattice constants of anatase, and the energies of bulk defects and surface structures are calculated. Reduction of anatase involving interstitial Ti is found to be the most favorable defect reaction in the bulk, with a lower energy than either Frenkel or Schottky reactions. The binding energies of selected defect clusters are also presented: for the Ti(3+)-Li(+) defect cluster, the binding energy is found to be approximately 0.5 eV, suggesting that intercalated Li ions stabilize conduction band electrons. The Li ion migration path is found to run between octahedral sites, with an activation energy of 0.45-0.65 eV for mole fractions of lithium in Li(x)TiO(2) of x < or = 0.1. The calculated surface energies are used to predict the crystal morphology, which is found to be a truncated bipyramid in which only the (101) and (001) surfaces are expressed, in accord with the available microscopy data. Calculations of defect energies at the (101) surface suggest that single Ti(3+) defects and neutral Ti(3+)-Li(+) pairs tend to segregate to the surface.     

Preparation of CH3TiF and (CH3)2TiF2 from the reaction of CH(3)F with laser-ablated Ti atoms

Laser-ablated Ti atoms react with CH(3)F upon condensation with excess argon to form primarily CH(3)TiF and (CH(3))(2)TiF(2). Irradiation in the UV region promotes alpha-hydrogen rearrangement of CH(3)TiF to CH(2)=TiHF and increases the yield of (CH(3))(2)TiF(2). Annealing to allow diffusion and reaction of more CH(3)F markedly increases the yield of (CH(3))(2)TiF(2). This shows that the CH(3)TiF + CH(3)F reaction is spontaneous and that triplet state CH(3)TiF is an extremely reactive molecule. B3LYP calculations are extremely effective in predicting vibrational frequencies and isotopic shifts for CH(3)TiF and (CH(3))(2)TiF(2) and thus in confirming their identification from matrix infrared spectroscopy.     

The reaction of TiF4 with Li(OC(CF3)2Ph): direct synthetic route to the lithium-titanium heterometallic fluoride bridged complex {Li(THF)2TiF3(OC(CF3)2Ph)2}2 and Ti(OC(CF3)2Ph)4 alkoxide

Reaction of TiF4 and LiORf (Rf = C(CF3)2Ph) in the donor solvent-THF lead to the isolation of the heterometallic lithium-titanium complex (THF)2Li(mu-F)2Ti(ORf)2(mu-F)2Ti(ORf)(2)(mu-F)2Li(THF)2 (1) and Ti(ORf)4 alkoxide (2). Interaction of TiF4 and LiORf in the non-coordinating and low polar toluene yielded only Ti(ORf)4 (2). Compounds 1 and 2 were characterized by X-ray single-crystal analysis, IR, NMR and mass spectrometry. Compound 1 is a centrosymmetric fluorine bridged dimer and contains the Li(mu-F)2Ti(mu-F)2Ti(mu-F)2Li cage. Complex 2 containing four bulky ligands is monomeric. NMR evidence is presented that the TiF4 and LiORf in THF solution gave lithium-titanium heterometallic complexes containing Li-(mu-F)-Ti and the Ti-(mu-F)-Ti bonds.     

Synthesis of aluminium borate-boron oxide and binary titanium-boron and zirconium-boron oxides from metal alkoxides and (MeO)3B3O3 in non-aqueous solvents

The reaction of metal alkoxides M(OR)4 (M = Ti, Zr; R = organyl) with (MeO)3B3O3 (1 : 0.67) in dry propan-2-one at room temperature led to gels which when dried and calcined in air for 24 h at 500-1000 degrees C afforded bi-phased mixed-oxide materials formulated as 4TiO2 x 3B2O3 and ZrO2 x B2O3 in high ceramic yields and purity; the B2O3 phases of these materials were amorphous. The materials remained amorphous upon calcination at lower temperatures. The TiO2 phase of the 4TiO2 x 3B2O3 was crystalline when calcined at higher temperatures with either anatase (600 degrees C) or rutile (>800 degrees C) being obtained. The ZrO2 phase of the ZrO2 x B2O3 was crystalline when calcined at higher temperatures and was obtained as a metastable tetragonal phase (<700 degrees C) or baddeleylite (>800 degrees C). In a similar reaction, Al(O(i)Pr)3 (2 : 1) gave a bi-phased aluminium borate-boron oxide (Al18B4O(33).7B2O3) after calcination at >700 degrees C. The dried gels and oxide materials were all characterized by elemental analysis, TGA-DSC, and powder XRD.     

Intracluster ion-molecule reactions of Ti+ with C2H5OH and CF3CH2OH clusters: influence of fluorine substituents on chemical reactivity

A laser ablation-molecular beam/reflectron time-of-flight mass spectrometric technique was used to investigate the ion-molecule reactions that proceed within Ti+(ROH)n (R = C2H5, CF3CH2) heterocluster ions. The mass spectra exhibit a major sequence of cluster ions with the formula Ti+(OR)m(ROH)n (m = 1, 2), which is attributed to sequential insertions of Ti+ into the O-H bond of C2H5OH or CF3CH2OH molecules within the heteroclusters, followed by H eliminations. The TiO+ and TiOH+ ions produced from the reactions of Ti+ with C2H5OH are interpreted as arising from insertion of Ti+ into the C-O bond, followed by C2H5 and C2H6 eliminations, respectively. When Ti+ reacted with CF3CH2OH, by contrast, considerable contributions from TiFOH+, TiF2+, and TiF2OH+ ions were observed in the mass spectrum of the reaction products, indicating that F and OH abstractions are the dominant product channels. Ab initio calculations of the complex of Ti+ with 2,2,2-trifluoroethanol show that the minimum energy structure is that in which Ti+ is attached to the O atom and one of the three F atoms of 2,2,2-trifluoroethanol, forming a five-membered ring. Isotope-labeling experiments additionally show that the chemical reactivity of heterocluster ions is greatly influenced by the presence of fluorine substituents and cluster size. The reaction energetics and formation mechanisms of the observed heterocluster ions are discussed.     

锰掺杂Ba0.6Sr0.4TiO3-MgTiO3复相陶瓷的制备和介电性能

以分析纯的Ba(NO3)2、Sr(NO3)2、草酸和钛酸丁酯为原料, 采用草酸盐共沉淀法制备了钛酸锶钡（Ba0.6Sr0.4TiO3, BST）纳米粉体. XRD和SEM分析结果表明, 该方法制备出立方相的Ba0.6Sr0.4TiO3粉体, 平均粒径小于100 nm, 具有较高的烧结活性. 用传统固相法制备了锰掺杂钛酸锶钡-钛酸镁(Ba0.6Sr0.4TiO3-MgTiO3, BST-MT)复相陶瓷, 系统研究了掺杂0.1%-2.0%(x, 摩尔分数, 下同)锰对钛酸锶钡-钛酸镁复相陶瓷微观形貌和介电性能的影响机理. 结果表明, 当锰的掺杂量小于1.5%时, Mn作为受主掺杂取代占据钙钛矿ABO3的B位, 因此导致居里点略微向高温偏移和相变扩散的发生, 锰的掺杂导致晶格畸变, 促进了晶粒生长, 使晶界相比例下降, 因此介电损耗随着锰掺杂量的增大而减小; 当锰的掺杂量为1.5%时, 介电损耗达到最小值, 继续增大掺杂量, 介电常数下降, 介电损耗上升.     

Synthesis of anatase TiO2 rods with dominant reactive {010} facets for the photoreduction of CO2 to CH4 and use in dye-sensitized solar cells

Single crystalline anatase TiO(2) rods with dominant reactive {010} facets are directly synthesized by hydrothermally treating Cs(0.68)Ti(1.83)O(4)/H(0.68)Ti(1.83)O(4) particles. The nanosized rods show a comparable conversion efficiency in dye-sensitized solar cells (DSSCs), and a superior photocatalytic conversion of CO(2) into methane to the benchmark P25 TiO(2) nanocrystals.     

Atomistic insights into the conversion reaction in iron fluoride: a dynamically adaptive force field approach

Nanoscale metal fluorides are promising candidates for high capacity lithium ion batteries, in which a conversion reaction upon exposure to Li ions enables access to the multiple valence states of the metal cation. However, little is known about the molecular mechanisms and the reaction pathways in conversion that relate to the need for nanoscale starting materials. To address this reaction and the controversial role of intercalation in a promising conversion material, FeF(2), a dynamically adaptive force field that allows for a change in ion charge during reactions is applied in molecular dynamics simulations. Results provide the atomistic view of this conversion reaction that forms nanocrystals of LiF and Fe(0) and addresses the important controversy regarding intercalation. Simulations of Li(+) exposure on the low energy FeF(2) (001) and (110) surfaces show that the reaction initiates at the surface and iron clusters as well as crystalline LiF are formed, sometimes via an amorphous Li-F. Li intercalation is also observed as a function of surface orientation and rate of exposure to the Li, with different behavior on (001) and (110) surfaces. Intercalation along [001] rapid transport channels is accompanied by a slight reduction of charge density on multiple nearby Fe ions per Li ion until enough Li saturates a region and causes the nearby Fe to lose sufficient charge to become destabilized and form the nanocluster Fe(0). The resultant nanostructures are fully consistent with postconversion TEM observations, and the simulations provide the solution to the controversy regarding intercalation versus conversion and the atomistic rationale for the need for nanoscale metal fluoride starting particles in conversion cathodes.     

锰掺杂Ba0.6Sr0．4TiO3-MgTiO3复相陶瓷的制备和介电性能

以分析纯的Ba(NO3)2、Sr(NO3)2、草酸和钛酸丁酯为原料,采用草酸盐共沉淀法制备了钛酸锶钡(Ba0.6Sr0.4tiO3,BST)纳米粉体.XRD和SEM分析结果表明,该方法制备出立方相的Ba0.6Sr0.4TiO3粉体,平均粒径小于100 nm,具有较高的烧结活性.用传统固相法制备了锰掺杂钛酸锶钡.钛酸镁(Ba0.6Sr0.4TiO3-MgTiO3,BST-MT)复相陶瓷,系统研究了掺杂0.1%-2.0%(x,摩尔分数,下同)锰对钛酸锶钡-钛酸镁复相陶瓷微观形貌和介电性能的影响机理.结果表明,当锰的掺杂量小于1.5%时,Mn作为受主掺杂取代占据钙钛矿ABO3的B位,因此导致居里点略微向高温偏移和相变扩散的发生,锰的掺杂导致晶格畸变,促进了晶粒生长,使晶界相比例下降,因此介电损耗随着锰掺杂量的增大而减小;当锰的掺杂量为1.5%时,介电损耗达到最小值,继续增大掺杂量,介电常数下降,介电损耗上升.     

Novel Ti-O-Ti bonding species constructed in a metal-oxide cluster

The preparation and structural characterization of a novel Ti-O-Ti bonding complex constructed in the mono-lacunary alpha-Keggin polyoxometalate (POM), are described. The water-soluble, crystalline complex with a formula of K5H2[[{Ti(OH)(ox)}2(micro-O)](alpha-PW11O39)] x 13H2O 1 was prepared in 30.2% (0.60 g scale) yield in a 1 : 3 molar-ratio reaction of the tri-lacunary species of alpha-Keggin POM, Na9[A-PW9O34] x 19H2O, with the titanium(IV) source, K2TiO(ox)2 x 2H2O (H2ox = oxalic acid), in HCl-acidic solution (pH 0.08), and characterized by complete elemental analysis, thermogravimetric and differential thermal analyses (TG/DTA), FTIR, solution (31P, 183W, 1H and 13C) NMR spectroscopy and X-ray crystallography. The complex was also obtained in 47.6% (0.81 g scale) yield in a 1 : 2 molar-ratio reaction of the mono-lacunary Keggin POM, K7[PW11O39] x 10H2O, with the anionic titanium(IV) complex under acidic conditions. The molecular structure of [[{Ti(OH)(ox)}2(micro-O)](alpha-PW11O39)]7- 1a, was successfully determined. This POM in the solid state is composed of one host (mono-lacunary site) and two guests (two octahedral Ti groups), in contrast to most titanium (IV)-substituted POMs consisting of one host and one guest. On the other hand, the 31P NMR measurements revealed that in aqueous solution this POM was present under a dissociation equilibrium which depends upon both temperature and pH.     

Deposition of a thin film of TiOx from a titanium metal target as novel blocking layers at conducting glass/TiO2 interfaces in ionic liquid mesoscopic TiO2 dye-sensitized solar cells

In dye-sensitized TiO2 solar cells, charge recombination processes at interfaces between fluorine-doped tin oxide (FTO), TiO2, dye, and electrolyte play an important role in limiting the photon-to-electron conversion efficiency. From this point of view, a high work function material such as titanium deposited by sputtering on FTO has been investigated as an effective blocking layer for preventing electron leakage from FTO without influencing electron injection. X-ray photoelectron spectroscopy analysis indicates that different species of Ti (Ti4+, Ti3+, Ti2+, and a small amount of Ti0) exist on FTO. Electrochemical and photoelectrochemical measurements reveal that thin films of titanium species, expressed as TiOx, work as a compact blocking layer between FTO and TiO2 nanocrystaline film, improving Voc and the fill factor, finally giving a better conversion efficiency for dye-sensitized TiO2 solar cells with ionic liquid electrolytes.     

锂钛复合氧化物锂离子电池负极材料的研究

采用 3种化学方法合成锂钛复合氧化物 .应用X -射线衍射分析对其结构进行表征以及电化学性能测试 ,结果表明 :由Li2 CO3、TiO2 高温合成的锂钛复合氧化物为尖晶石结构的Li4Ti5 O12 .Li4Ti5 O12 电极在 1 .5V左右有一放电平台 ,充放电可逆性良好 ,即充电电压平台与此接近 ,且电极的比容量较大 ,循环性能良好 .以 0 .30mA·cm- 2 充放电时 ,首次放电容量可达 30 0mAh·g- 1,可逆比容量为 1 0 0mAh·g- 1,经多次充放电循环后 ,其结构仍保持稳定性 .试验电池测试表明 ,Li4Ti5 O12 可选作Li4Ti5 O12 /LiCoO2 锂离子电池的负极材料 .     

Hierarchical TiO(2) flowers built from TiO(2) nanotubes for efficient Pt-free based flexible dye-sensitized solar cells

A novel hierarchical TiO(2) flower consisting of anatase TiO(2) nanotubes on a Ti foil substrate has been prepared via a mild hydrothermal reaction of TiO(2) nanoparticles/Ti foil. The photovoltaic performance of DSSC based on hierarchical TiO(2) flowers/Ti (7.2%) is much higher than that of TiO(2) nanoparticle/Ti (6.63%) because of its superior light scattering ability and fast electron transport. Moreover, full flexible DSSC based on the novel hierarchical TiO(2) flowers/Ti foil photoelectrode and electrodeposited poly(3,4-ethylenedioxythiophene) (PEDOT) on indium tin oxide-coated poly(ethylene terephthalate) (ITO-PET) counter electrode shows a significant power conversion efficiency of 6.26%, accompanying a short-circuit current density of 11.96 mA cm(-2), an open-circuit voltage of 761 mV and a fill factor of 0.69.     

TiO2柱层状HTiNbO5的合成及在环己酮肟气相Beckmann重排反应中的催化性能

钛酸异丙酯(TIP)、CH₃COOH和H₂O按体积比1∶16∶40混合后得到Ti(Ⅳ)多聚阳离子柱化液, 与正癸胺插层钛铌酸盐进行交换反应后制得钛(Ⅳ)多聚阳离子插层钛铌酸盐, 其层间距为1.70 nm. 在空气气氛中于623 K焙烧处理后, 所得产品能保持良好的层柱结构. 在空气气氛中于723 K焙烧后所得的TiO₂柱层状钛铌酸(TiO₂-HTiNbO₅), 其层间距为0.97 nm, 比表面积为89 m²/g. 以TiO₂-HTiNbO₅为载体, 用浸渍法制备了一系列B₂O₃负载量不同的负载型样品B₂O₃/TiO₂-HTiNbO₅, 考察了它们在环己酮肟气相Beckmann重排反应中的催化性能并测试了它们的红外光谱. B₂O₃/TiO₂-HTiNbO₅的催化性能优于TiO₂-HTiNbO₅. 在B₂O₃负载质量分数为7.31%的催化剂上, 环己酮肟转化率接近100%且在4.5 h内无明显改变, 己内酰胺选择性接近90%. 红外光谱分析结果表明, 当B₂O₃负载量很低时, 硼组分高度分散于载体TiO₂-HTiNbO₅表面, 并主要以BO₄结构形式存在; 当B₂O₃负载质量分数高于7.31%时, BO₃结构形式在数量上占优势. 将催化性能与红外光谱结果关联后可知, 对于负载型样品B₂O₃/TiO₂-HTiNbO₅, 表面的BO₃和BO₄两种结构形式在环己酮肟气相Beckmann重排反应中具有协同促进作用.     

锂离子电池新型快充负极材料Li4Ti5O12的改性研究

采用传统固相法制备尖晶石型Li4Ti5O12, 在前驱物中掺杂聚合物裂解碳材料聚并苯(PAS). 经四探针测试仪测量, 电导率提高9个数量级. 复合物的电化学性能测试结果表明, 其循环性和高倍率性能得到了明显改善.     

Trapping of charge carriers in colloidal particles of self-assembled films from TiO(2) and poly(vinyl sulfonic acid)

Self-assembled electrodes consisting of TiO(2) nanoparticles and poly(vinyl sulfonic acid) (PVS) were prepared by the layer-by-layer (LbL) technique. The electrostatic interaction between the TiO(2) nanoparticles and PVS allowed the growth of visually uniform multilayers of the composite, with high control of the thickness and nanoarchitecture. The electrochemical and chromogenic properties of these TiO(2)/PVS films were examined in an electrolytic solution of 0.5 M LiClO(4)/propylene carbonate. The presence of two intercalation sites was noted during the positive potential scan, and they were attributed to different mobilities of charge carriers. Several charge/discharge cycles demonstrated the trapping of charge carriers in the TiO(2) sites. The absorbance change associated with the oxidation of the trapping sites was attributed to electronic transitions involving energy states in the gap band formed due to the strong distortion of the TiO(2) host. Using the quadratic logistic equation (QLE), it was possible to analyze the electronic intervalence transfer from Ti(3+) to Ti(4+). Using the parameters obtained from this fitting, the amount of trapping sites in the LbL film was also determined. Electrochemical impedance spectroscopy (EIS) data gave the time constant associated with diffusion and the trapping sites. The diffusion coefficient of lithium ions changed from ca. 4.5 x 10(-13) cm(2) s(-1) to 3.0 x 10(-14) cm(2) s(-1) for all the potential range applied, indicating that PVS did not hinder the ionic transport within the LbL film. Finally, on the basis of the spectroelectrochemical data and scanning electron micrographs, the trapping effects were attributed to the colloidal particles of Li(0.55)TiO(2).     

Effect of TiO2 crystalline phase composition on the physicochemical and catalytic properties of Pd/TiO(2) in selective acetylene hydrogenation

Pd/TiO(2) catalysts have been prepared using TiO(2) supports consisting of various rutile/anatase crystalline phase compositions. Increasing percentages of rutile phase in the TiO(2) resulted in a decrease in Brunauer-Emmett-Teller surface areas, fewer Ti(3+) sites, and lower Pd dispersion. While acetylene conversions were found to be merely dependent on Pd dispersion, ethylene selectivity appeared to be strongly affected by the presence of Ti(3+) in the TiO(2) samples. When TiO(2) samples with 0-44% rutile were used, high ethylene selectivities (58-93%) were obtained whereas ethylene losses occurred for those supported on TiO(2) with 85% or 100% rutile phase. X-ray photoelectron spectroscopy and electron spin resonance experiments revealed that a significant amount of Ti(3+) existed in the TiO(2) samples composed of 0-44% rutile. The presence of Ti(3+) in contact with Pd can probably lower the adsorption strength of ethylene resulting in an ethylene gain. Among the five catalysts used in this study, the results for Pd/TiO(2)-R44 suggest an optimum anatase/rutile composition of the TiO(2) used to obtain high selectivity of ethylene in selective acetylene hydrogenation.     

TiO2与ZnO复合纳米结构电极的光电化学研究

利用尿素加压共沉淀法以Ti(SO4)2与Zn(NO3)2为原料制备了TiO2-ZnO复合纳米粒子, 其纳米结构电极的光电化学研究结果表明, 反应物摩尔比为3∶1, 于530 ℃煅烧制备的复合纳米结构电极的光电转换效率最高. 对吸附染料RuL2(SCN)2∶2TBA的纳米结构TiO2和各种复合纳米粒子的纳米结构电极进行光电研究的结果表明, 染料对各纳米结构电极都起到了敏化作用, 其中也是由反应物摩尔比为3∶1, 于530 ℃煅烧制备的纳米结构电极的光电转换效率最高. 对聚3-甲基噻吩修饰的纳米结构TiO2和摩尔比为3∶1, 于530 ℃煅烧的复合纳米粒子构成的纳米结构电极进行光电性能研究, 结果表明, 聚3-甲基噻吩与半导体纳米粒子之间存在p-n结, 在一定条件下p-n结的存在有利于光生电子/空穴的分离, 从而提高了光电转化效率.     

Preparation of Ti(IV) fluoride N-heterocyclic carbene complexes

1,3,4,5-Tetramethylimidazol-2-ylidene (L(Me)) and 1,3-diisopropyl-4,5-dimethylimidazol-2-ylidene (L(iPr )) readily form complexes of trans-TiF4(L(Me))2 (1) and of trans-TiF4(L(iPr))2 (4) with TiF4 in THF, respectively. Complex 1 has been used as a precursor for preparing the Ti(IV) fluoride carbene complexes [{TiF2(L(Me))(NEt 2)}2(mu-F)2] (2) and (TiF4(L(Me))2)(NacNacLi) (3) (NacNac = HC(CMeN(2,6- iPr2C6H3))2). Complex 2 was prepared from the reaction of 1-3 equiv of 1 and 1 equiv of Ti(NEt2)4 or by reacting TiF4 with Ti(NEt2)4 and L(Me) in toluene. Complex 3 has been prepared from 1 and NacNacLi in toluene. Reaction of 1 and AlMe3 in toluene results in ligand transfer and formation of AlMe3(L(Me)). Complex 4 is unstable in solution at room temperature and degrades with formation of [HL(iPr)][TiF5(L(iPr))] (5). Complexes 1, 2.2CH2Cl2, 4, and 5 were characterized by single crystal X-ray structural analysis, elemental analysis, IR and NMR spectroscopy, and mass spectrometry. The relative basicities of L(Me), L (iPr), and the donor ligands THF, pyridine, DMSO, and H2O as well as [Cl](-) and [F](-) toward the Ti(IV) pentafluoride anion were established by NMR and confirmed by density functional theory (DFT) calculations. L(Me) and L(iPr ) are more basic than the mentioned molecular donors and more basic than chloride, however less basic than fluoride.