A simple method to synthesize single-crystalline β-wollastonite nanowires

The single-crystalline β-wollastonite (β-CaSiO₃) nanowires were prepared via a simple hydrothermal method, in the absence of any template or surfactant using cheap and simple inorganic salts as raw materials. Xonotlite [Ca₆(Si₆O₁₇)(OH)₂] nanowires were first obtained after hydrothermal treatment at a lower temperature of 200 °C for 24 h, and after being calcinated at 800 °C for 2 h, xonotlite nanowires completely transformed into β-wollastonite nanowires and the wire-like structure was preserved. The synthesized β-wollastonite nanowires had a diameter of 10–30 nm, and a length up to tens of micrometers, and the single-crystalline monoclinic parawollastonite structured β-wollastonite was identified by XRD with the space group of P2₁/a and cell constants of a=15.42 Å, b=7.325 Å, c=7.069 Å and β=95.38°. A possible growth mechanism of β-wollastonite nanowires was also proposed. The advantages of this method for the nanowire synthesis lie in the high yield, low temperature and mild reaction conditions, which will allow large-scale production at low cost.     

Investigation of Ni/Au-contacts on p-GaN annealed in different atmospheres

We investigated the effect of different annealing atmospheres on contact behaviour of Ni/Au contacts on moderately doped p-GaN layers. We used the annealing gases N₂, O₂, Ar, and forming gas (N₂/H₂) at varying annealing temperatures from 350°C to 650°C in steps of 50°C. The p-GaN samples were either metalorganic chemical vapor deposition or molecular beam epitaxy grown. Contact characterization was done after each annealing step by using the circular transmission line model. Specific contact resistances were determined to be in the low 10⁻⁴ Ω cm² range for oxidized contacts. Accompanying chemical analysis using depth resolved Auger electron spectroscopy revealed that NiO was formed and Au diffused towards the interface, whereas annealing in forming gas prevented oxidation and did not lead to Ohmic behaviour.     

Growth and properties of (Pb0.90La0.10)TiO3 thick films prepared by RF magnetron sputtering with a PbO buffer layer

The (Pb_0.90La_0.10)TiO₃ [PLT] thick films (3.0 μm) with a PbO buffer layer were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering method. The PLT thick films comprise five periodicities, the layer thicknesses of (Pb_0.90La_0.10)TiO₃ and PbO in one periodicity are fixed. The PbO buffer layer improves the phase purity and electrical properties of the PLT thick films. The microstructure and electrical properties of the PLT thick films with a PbO buffer layer were studied. The PLT thick films with a PbO buffer layer possess good electrical properties with the remnant polarization (P_r=2.40 μC cm⁻²), coercive field (E_c=18.2 kV cm⁻¹), dielectric constant (ε_r=139) and dielectric loss (tan δ=0.0206) at 1 kHz, and pyroelectric coefficient (9.20×10⁻⁹ C cm⁻² K⁻¹). The result shows the PLT thick film with a PbO buffer layer is a good candidate for pyroelectric detector.     

Synthesis, thermal and magnetic properties of new metal iodate: (LiFe1/3)(IO3)2

This paper reports the detail synthesis of a new kind of metal iodate, anhydrous (LiFe_1/3)(IO₃)₂, from aqueous solutions. The synthesized compound shows spinal morphology and is chemical stable up to 400°C. The iodate shows paramagnetic behavior from room temperature down to 4.2 K. At room temperature, the new compound has a hexagonal structure with the lattice parameters a=5.4632(2) Å, c=5.0895(6) Å, Z=1, space group of P6₃.     

Investigations on the effect of InSb and InAsSb step-graded buffer layers in InAs0.5Sb0.5 epilayers grown on GaAs (0 0 1)

We report the structural and electrical properties of InAsSb epilayers grown on GaAs (0 0 1) substrates with mid-alloy composition of 0.5. InSb buffer layer and InAs_xSb_1−x step-graded (SG) buffer layer have been used to relax lattice mismatch between the epilayer and substrate. A decrease in the full-width at half-maximum (FWHM) of the epilayer is observed with increasing the thickness of the InSb buffer layer. The surface morphology of the epilayer is found to change from 3D island growth to 2D growth and the electron mobility of the sample is increased from 5.2×10³ to 1.1×10⁴ cm²/V s by increasing the thickness of the SG layers. These results suggest that high crystalline quality and electron mobility of the InAs_0.5Sb_0.5 alloy can be achieved by the growth of thick SG InAsSb buffer layer accompanied with a thick InSb buffer layer. We have confirmed the improvement in the structural and electrical properties of the InAs_0.5Sb_0.5 epilayer by quantitative analysis of the epilayer having a 2.09 μm thick InSb buffer layer and 0.6 μm thickness of each SG layers.     

Improving the performance of thermoelectric devices by doping Ag in LaPbMnO3 thin films

A series of Ag-doped La_0.6Pb_0.4MnO₃ thin films were grown on vicinal cut substrates by pulsed laser deposition (PLD). Laser-induced thermoelectric voltages (LITV) had been observed in these films, and these LITV signals had been demonstrated to originate from the anisotropic Seebeck effect. By doping Ag to an optimum value, it was found that the peak values (U_P) of the LITV signals were maximized, and the full-width at half-maximum (τ) of the response curves of LITV were minimized at the same time. The figure of merit (F_m) of the device used as photodetector is greatly improved by doping Ag in La_0.6Pb_0.4MnO₃ thin films. The possible reason for these improvements had been well discussed.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Properties of ZnO films grown on (0 0 0 1) sapphire substrate using H2O and N2O as O precursors by atmospheric pressure MOCVD

In this paper, we compare the properties of ZnO thin films (0 0 0 1) sapphire substrate using diethylzinc (DEZn) as the Zn precursor and deionized water (H₂O) and nitrous oxide (N₂O) as the O precursors, respectively in the main ZnO layer growth by atmospheric pressure metal–organic chemical vapor deposition (AP-MOCVD) technique. Surface morphology studied by atomic force microscopy (AFM) showed that the N₂O-grown ZnO film had a hexagonal columnar structure with about 8 μm grain diameter and the relatively rougher surface compared to that of H₂O-grown ZnO film. The full-widths at half-maximum (FWHMs) of the (0 0 0 2) and () ω-rocking curves of the N₂O-grown ZnO film by double-crystal X-ray diffractometry (DCXRD) measurement were 260 and 350 arcsec, respectively, indicating the smaller mosaicity and lower dislocation density of the film compared to H₂O-grown ZnO film. Compared to H₂O-grown ZnO film, the free exciton A (FX_A) and its three phonon replicas could be clearly observed, the donor-bound exciton A⁰X (I₁₀):3.353 eV dominated the 10 K photoluminescence (PL) spectrum of N₂O-grown ZnO film and the hydrogen-related donor-bound exciton D⁰X (I₄):3.363 eV was disappeared. The electron mobility (80 cm²/V s) of N₂O-grown ZnO film has been significantly improved by room temperature Hall measurement compared to that of H₂O-grown ZnO film.     

CrO2 (1 0 0) and TiO2 (1 0 0) film heteroepitaxy on a BaF2 (1 1 1)/Si (1 0 0) substrate

Multi-domained heteroepitaxial rutile-phase TiO₂ (1 0 0)-oriented films were grown on Si (1 0 0) substrates by using a 30-nm-thick BaF₂ (1 1 1) buffer layer at the TiO₂–Si interface. The 50 nm TiO₂ films were grown by electron cyclotron resonance oxygen plasma-assisted electron beam evaporation of a titanium source, and the growth temperature was varied from 300 to 600 °C. At an optimal temperature of 500 °C, X-ray diffraction measurements show that rutile phase TiO₂ films are produced. Pole figure analysis indicates that the TiO₂ layer follows the symmetry of the BaF₂ surface mesh, and consists of six (1 0 0)-oriented domains separated by 30° in-plane rotations about the TiO₂ [1 0 0] axis. The in-plane alignment between the TiO₂ and BaF₂ films is oriented as [0 0 1] TiO₂ || BaF₂ or [0 0 1] TiO₂ || BaF₂ . Rocking curve and STM analyses suggest that the TiO₂ films are more finely grained than the BaF₂ film. STM imaging also reveals that the TiO₂ surface has morphological features consistent with the BaF₂ surface mesh symmetry. One of the optimally grown TiO₂ (1 0 0) films was used to template a CrO₂ (1 0 0) film which was grown via chemical vapor deposition. Point contact Andreev reflection measurements indicate that the CrO₂ film was approximately 70% spin polarized.     

Synthesis, growth, thermal, optical, dielectric and mechanical properties of semi-organic NLO crystal: Potassium hydrogen malate monohydrate

Potassium hydrogen malate monohydrate (PHMM), a semi-organic nonlinear optical material, has been synthesized and single crystals were grown from aqueous solution. Single crystals of PHMM have been grown by slow evaporation of solvent at room temperature up to dimensions of 22 mm×16 mm×14 mm. Single-crystal X-ray diffraction study on grown crystals shows that they belong to monoclinic system and non-centrosymmetry spacegroup Cc. The structural perfection of the grown crystals has been analyzed by high-resolution X-ray diffraction (HRXRD) rocking curve measurements. Fourier transform infrared (FTIR) spectroscopic study was performed for the identification of different modes of functional groups present in the compound. The UV–Vis transmission spectrum has been recorded in the range 200–1100 nm. The thermal stability of the compound has been determined by TG-DTA curves. The dielectric studies were performed. From the microhardness measurements, Vicker's hardness number (H_v), Stiffness constant (C₁₁), fracture toughness (k_c), Brittle index (B_i) and yield strength (σ_y) have been calculated. The Young's modulus was calculated using the Knoop hardness measurement. The SHG relative efficiency of PHMM crystal was found to be 1.2 times higher than that of KDP.     

Sol–gel synthesis and optical properties of size controlled Indium Arsenide nanocrystals embedded in silica glasses

III–V semiconductor Indium Arsenide (InAs) nanocrystals embedded in silica glasses was synthesized by combining the sol–gel process and heat treatment in H₂ gas. The size of InAs nanocrystals can be easily controlled via changing the In and As content in the starting materials and the heating temperature in a H₂ gas atmosphere. Absorption measurements indicate a blue shift in energy with a reduction on the In and As content in the SiO₂ gel glasses as a result of quantum confinement effects. A near-infrared photoluminescence with peak at 3.40 μm was observed at 6 K under 514.5 nm Ar⁺ laser excitation from InAs nanocrystals embedded in the silica gel glasses.     

Porous crystal structures obtained from directionally solidified eutectic precursors

Interconnecting cage-like porous structures of several halide compounds were prepared by the selective leaching of one eutectic phase method. The binary eutectic precursors were prepared by directional solidification using the Bridgman crystal growth technique. Porous NaMgF₃ (40% pore volume), CaF₂ (57% pore volume) and BaF₂ (43% pore volume) crystals were obtained after water leaching the NaF component of the directionally solidified NaF/NaMgF₃, NaF/CaF₂ and NaF/BaF₂ eutectics with the appropriate entangled microstructure. The growth conditions for eutectic-coupled growth and the morphology of the eutectics have been determined. In the coupled growth regime, the size of the eutectic phases “λ” is fairly uniform and varies with the eutectic growth rate “v” as λ²v=constant, which allows us to control the pore size within the 0.5–10 μm range. The simplicity and versatility of the eutectic growth also allows us to fabricate highly aligned porous structures at relatively high production rates.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.     

The incorporation behavior of arsenic and antimony in GaAsSb/GaAs grown by solid source molecular beam epitaxy

GaAsSb ternary epitaxial layers were grown on GaAs (0 0 1) substrate in various Sb₄/As₂ flux ratios by solid source molecular beam epitaxy. The alloy compositions of GaAs_1−ySb_y were inferred using high-resolution X-ray symmetric (0 0 4) and asymmetric (2 2 4) glance exit diffraction. The non-equilibrium thermodynamic model is used to explain the different incorporation behavior between the Sb₄ and As₂ under the assumption that one incident Sb₄ molecule produces one active Sb₂ molecule. It is inferred that the activation energy of Sb₄ dissociation is about 0.46 eV. The calculated results for the incorporation efficiency of group V are in good agreement with the experimental data.     

Studies of the facetting of the polished (100) face of CaF2

The present paper deals with studies of the facetting of the polished (1 0 0) surface of CaF₂ during annealing and growth in UHV using low energy electron diffraction (LEED), atomic force microscopy (AFM), and transmission electron microscopy (TEM). First morphological modifications of the polished surfaces become visible at temperatures of T=874 K. Surfaces annealed at T=974 K exhibit a micro-roughening with pyramidal protrusions and corresponding depressions. LEED studies indicate the evolution of {1 1 1} facets. Reflexes from the (1 0 0) surface are not seen. After growth of about 660 monolayers of CaF₂ at T=1093 K and a saturation ratio S=33 from the vapor phase, larger pyramid-like or hip roof-like crystallites are developed. The results of AFM height profiles as well as of the LEED investigations indicate again the formation of {1 1 1} facets as proved by their angles of 54.7 ^o with the base (1 0 0) surface. This shows that the crystallites are homoepitaxially grown on the underlying CaF₂ substrate.     

Crystal structure, carrier concentration and IR-sensitivity of PbTe thin films doped with Ga by two different methods

The comparison of the results of chemical composition, crystal structure, electronic properties and infrared photoconductivity investigations of PbTe/Si and PbTe/SiO₂/Si heterostructures doped with Ga atoms by two different techniques is presented in this work. One of these techniques is principally based on the vapour-phase doping procedure of PbTe/Si and PbTe/SiO₂/Si heterostructures, which were previously formed by the modified “hot wall” technique. The second method of PbTe(Ga)/Si and PbTe(Ga)/SiO₂/Si heterostructure preparation is based upon the fabrication of lead telluride films, which have been doped with Ga atoms in the layer condensation process directly. The lattice parameter and charge carrier density evolutions with the Ga impurity concentration show principally the different character of PbTe(Ga)/Si films prepared by these techniques. It has been proposed that complicated amphoteric (donor or acceptor) behaviour of Ga atoms may be explained by different mechanisms of substitution or implantation of impurity atoms in the crystal structure of lead telluride.     

Low-temperature fabrication and photocatalytic activity of clustered TiO2 particles formed on glass fibers

Clustered anatase phase TiO₂ particles were uniformly formed on the surface of glass fibers by a liquid phase deposition (LPD) method at 60 °C using TiF₄ and H₃BO₃ as the precursors. The clustered TiO₂ particles deposited on the glass fibers and as a photocatalyst these particles not only have a larger surface area than TiO₂ thin films, but also can avoid the disadvantages of using TiO₂ powders encountered in air purification or water treatment. The photocatalytic activity of the sample was evaluated by the photocatalytic oxidation of nitrogen monoxide (NO) in the gaseous phase. The deposition conditions and chemical composition of the clustered TiO₂ particles were discussed. It was found that the clustered TiO₂ particles that formed on the glass fibers obviously showed photocatalytic activity without high-temperature calcination. A formation mechanism was proposed to account for the formation of TiO₂ clustered morphology on the glass fibers.     

High-resolution XRD study of stress-modulated YBCO films with various thicknesses

High-quality epitaxial YBa₂Cu₃O_7−δ (YBCO) superconducting films with thicknesses between 0.2 and 2 μm were fabricated on (0 0 l) LaAlO₃ with direct-current sputtering method. The influence of film thickness on the structure and texture was investigated by X-ray diffraction conventional θ–2θ scan and high-resolution reciprocal space mapping (HR-RSM). The films grew with strictly c-axis epitaxial, and no a-axis-oriented growth was observed up to a thickness of 2 μm. Lattice parameters of the YBCO films with different thicknesses were extracted from symmetry and asymmetry HR-RSMs. The X-ray lattice parameter method was used to determine the residual stress in YBCO films by measuring the a-, b-, c-axis strains, respectively. The results showed that YBCO films within thinner than 1 μm were under compressive stress, which was relieved increasing of film thickness. However, beyond 1 μm in thickness, YBCO films exhibited a tensile stress. Based on the experimental analysis, the variety of residual stresses in the films is mainly attributed to oxygen vacancies with thickness of YBCO film increasing.     

High-resolution electron microscopy of microstructure of SrTiO3/BaZrO3 bilayer thin films on MgO substrates

SrTiO₃/BaZrO₃ heterofilms as buffer layers are deposited on (0 0 1) MgO substrates by an RF-sputtering technique. The atomic structure and the defect configuration at the interfaces are investigated by means of aberration-corrected high-resolution transmission electron microscopy. At the BaZrO₃/MgO interface, two types of interfacial structures, MgO/ZrO₂-type and MgO/BaO-type, are observed. Antiphase boundaries and dislocations are found at the BaZrO₃/MgO interface. The formation of these lattice defects is discussed in terms of film growth and structural imperfections of the substrate surface. At the SrTiO₃/BaZrO₃ interface, a high density of misfit dislocations is observed with different configurations. The formation of these dislocations contributes both to the relaxation of the large misfit strain and to stopping of the further propagation of lattice defects which are formed in the BaZrO₃ layer into the SrTiO₃ layer.     

Microstructure and ferroelectric properties of BaTiO3 films on LaNiO3 buffer layers by rf sputtering

We have fabricated LaNiO₃ and BaTiO₃ films using the rf sputtering method. The LaNiO₃ were deposited on Si substrates, demonstrating a (1 0 0) highly oriented structure and nanocrystalline characteristic with a grain size of 30 nm. The BaTiO₃ thin films were deposited on the LaNiO₃ buffer layers, and have exhibited a (1 0 0) texture with a thickness of 400 nm. A smooth interface is obtained between the LaNiO₃ bottom electrode and the BaTiO₃ film from cross-section observations by scanning electron microscopy. The bi-layer films show a dense and column microstructure with a grain size of 60 nm. Ferroelectric characterizations have been obtained for the BaTiO₃ films. The remnant polarization and coercive field are 2.1 μC/cm² and 45 kV/cm, respectively. The leak current measurements have shown a good insulating property.