Ag@AgCl修饰TiO2-xCx光催化剂的制备及其可见光降解污染物性能

以钛酸丁酯和葡萄糖为原料用水热法制备了碳掺杂二氧化钛,再进一步对其进行Ag@AgCl表面修饰.用X射线衍射(XRD),X射线光电子能谱(XPS),透射电镜(TEM),BET比表面仪和紫外-可见(UV-Vis)漫反射光谱等手段对样品进行测试表征;在可见光辐射下(λ＞420 nm),以甲基橙和苯酚溶液的光催化降解实验来评价样品的活性.结果表明:经Ag@AgCl修饰后,样品的粒径增大,比表面积减小,对可见光的响应增强;可见光光催化效率有大幅度提高,对甲基橙和苯酚的降解效率分别是修饰前的5.5和3.4倍,且光催化剂经三次循环使用后活性基本保持不变.     

离子液体-水混合溶剂中制备纳米晶TiO2的结构特性及其光催化活性

以钛酸四丁酯为原料, 离子液体1-乙基-3-甲基咪唑醋酸盐([EMIM]+AcO-)-水为混合溶剂, 通过低温水热法制备了锐钛矿相TiO2纳米晶. 用XRD、N2吸附-脱附、XPS及UV-Vis漫反射等技术对产物的晶相、比表面积、表面性质及光吸收性进行表征, 并以甲基橙水溶液为研究对象, 考察了产物的光催化活性及催化剂用量、溶液酸碱度对其的影响. 结果表明, 离子液体鄄水混合溶剂中反应24 h 所得到的TiO2具有较高光催化活性, 并明显优于Degussa P25, 这一结果可归因于其具有较高的锐钛矿含量和较大的比表面积.     

共价键联的PW11/TiO2介孔杂化材料的合成及其光催化性能

采用二次嫁接的方法,将Keggin结构的缺位钨磷酸盐PW11嫁接到介孔TiO2的表面,得到PW11/TiO2杂化样品。采用IR、低温N2吸附、XRD、TEM和ICP-AES等对样品的结构、PW11负载量以及键联机理进行了表征和研究,对样品光催化降解甲基橙的性能进行了考察。 结果显示,用蒸发诱导自组装法合成的TiO2,焙烧前结构松散,可部分水解并与PW11反应,生成PW11Ti物种,后者与TiO2骨架缩合,从而实现PW11的键联嫁接。 与纯TiO2相比,杂化样品中锐钛矿相的结晶度稍有降低,孔径、孔容减小,但是对甲基橙的光催化降解活性却明显增加,显然这是PW11和TiO2间发生了“协同效应”所致。     

Influence and Characterization of Acidity on Fine Silicon Powder Immobilized Photocatalyst

TiO2 photocatalyst was supported with tetrabutyl titanate sol as precursor and fine silicon powder obtained from ferroalloys factory as carder to discuss the influence of pH value of gel precursor on microstructure and activity of photocatalyst in the process of synthesizing nano-TiO2 by using sol-gel method, the purpose of which is to provide fundamental data for the recycle of photocatalytic material. Under the irradiation of ultraviolet light, the photocatalytic degradation rate of methyl orange solution was used to characterize the photocatalytic activity of the sample. The specific surface area of the sample was tested by N2 desorption method, crystal form of TiO2 was analyzed by X-ray powder diffraction, and the microtopography of the sample was observed by scanning electron microscopy. The experimental results showed that the acidity of gel precursor could greatly affect the specific surface area and photocatalytic activity of the photocatalyst, and the optimum pH value of the precursor was determined as 2.0, and at this time the specific surface area of photocatalyst could reach 34.0 m^2/g. In the sample, the proporticn of anatase to rutile is 7：3, which makes l0 mg·L^-1 methyl orange solution fade after irradiation by 15W ultraviolet light for 24 h, and the degradation rate might be up to 98.1%.     

钬掺杂提高TiO2纳米晶光催化活性的光谱性能机制研究

采用酸催化的溶胶-凝胶法制备了未掺杂和掺杂0.5%Ho(摩尔分数)的纳米TiO2光催化剂,以甲基橙的光催化降解为探针反应,评价了其光催化活性。运用XRD,TEM,EDS,FT-IR,UV-Vis DRS以及PL光谱表征技术考察了Ho掺杂对纳米TiO2的微晶尺寸、晶体结构、表面组成与光学性能的影响,并对改性机制作了探讨。结果表明,Ho掺杂可以抑制TiO2由锐钛矿相向金红石相的转变,阻碍TiO2晶粒增长,使TiO2的光吸收带边发生蓝移,增加表面羟基含量,促进光生载流子分离,从而使Ho掺杂TiO2样品光催化降解甲基橙的能力显著增强。     

纳米TiO2复合薄膜光催化降解甲基橙的研究

本文通过Sol-Gel工艺在载玻片表面、多孔陶瓷表面及玻璃纤维表面制得了均匀透明的纳米TiO₂复合薄膜,以甲基橙为研究对象,紫外灯为光源,研究了甲基橙初始浓度、光照时间、催化剂载体比表面、初始溶液的pH值对甲基橙降解率的影响,并比较了半导体耦合薄膜的光催化降解能力.研究结果表明:SnO₂-TiO₂复合膜相对于其它耦合膜及金属(La)掺杂膜有较高的降解率.     

Preparation and photocatalytic activity of TiO_2-coated granular activated carbon composites by a molecular adsorption-deposition method

TiO2 nanoparticle-coated granular activated carbon (GAC) composite photocatalysts (CPs) were suc-cessfully prepared by a molecular adsorption-deposition (MAD) method. The CPs were detected by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), BET surface area and UV-Vis adsorption spectroscopy, and their photoactivity was evaluated by methyl orange (MO) photodegradation. The results show that small-sized TiO2 nanoparticles were dispersed well, deposited on the surface of GAC, and showed slight blue shift in comparison with pure TiO2. With the increase in TiO2 content, the CPs showed band gaps in lower energy, smaller surface areas and the higher content of Ti3 ions. Compared with pure TiO2 and others CPs samples, CPs-382 sample showed the highest photoactivity due to the optimum TiO2 content and surface area besides the synergic effect of photocatalytic degradation of TiO2 and adsorptive property of GAC. In addition, the CPs could be very easily reclaimed, recycled and reused for methyl orange removal while high photoactivity is pre-served.     

Photocatalytic degradation of wastewater pollutants: titanium dioxide mediated degradation of methyl orange and beta-naphthol orange

The photocatalytic degradation of azo dyes such as methyl orange and beta-naphthol orange in aqueous suspensions of TiO2 has been investigated under a variety of conditions. The kinetics of degradation was studied under different conditions such as reaction pH, substrate and catalyst concentration, and types of titanium dioxide used and in the presence of electron acceptors and electron donors. The degradation rates of the dyes have been found to be strongly influenced by all the above parameters. Carbon dioxide yield measurements indicate that only partial mineralization occurs in the initial phase of oxidation.     

多酸修饰二氧化钛纳米管复合膜的制备、表征及其光催化降解甲基橙的研究

采用电沉积方法制备了H3PW12O40(PW12)-TiO2复合膜,通过SEM,EDX和XRD等手段,对其组成和结构进行了表征,并考察了该复合膜催化剂对降解甲基橙的催化活性.实验结果表明PW12存在于TiO2纳米管结构中,用PW12多酸修饰的TiO2纳米管比单独的TiO2纳米管展示出更好的光催化性能,由于电子能够从TiO2纳米管导带转移到多酸的LUMO能级,有效抑制了光生电子和空穴的复合,因而使PW12-TiO2复合膜表现出更高的光催化活性.     

低量La3+掺杂S-TiO2光催化剂的制备、表征及其光催化活性

采用溶胶-凝胶-浸渍法制备了La³⁺/S-TiO₂纳米光催化剂,通过XRD、BET、XPS、UV-Vis等手段进行了表征.以甲基橙溶液为光催化降解反应的模型化合物,考察了光催化剂的活性,探讨了低量La³⁺掺杂对TiO₂纳米粒子光催化活性的影响机制.实验结果表明:S改性TiO₂后明显提高了TiO₂纳米粒子的光催化活性,而La³⁺掺杂S-TiO₂后,进一步提高了TiO₂纳米粒子的光催化活性,La³⁺的最佳掺杂量(相对于TiO₂的质量分数)为0.369%;La³⁺/S-TiO₂(ω(La³⁺)=0.369%)为纳米光催化剂时,甲基橙的脱色率达到92.4%(光照120min);XRD和BET分析表明,低量La³⁺掺杂抑制了TiO₂由锐钛矿向金红石的转变,阻碍了TiO₂晶粒的生长,提高了TiO₂的比表面积;XPS分析表明,S、La³⁺掺杂可以导致粉体的表面羟基含量增加,掺杂S以S⁶⁺形式置换TiO₂晶格中的Ti⁴⁺;UV-Vis分析表明,光催化剂La³⁺/S-TiO₂比纯TiO₂具有较强的紫外光吸收性能.与纯TiO₂相比,La³⁺掺杂TiO₂纳米粒子光催化氧化活性的提高应归因于La³⁺掺杂增加了表面羟基含量,增大了比表面积,增强了样品表面的紫外光吸收能力.     

热分解法制备Fe2O3修饰的TiO2纳米管阵列及其光电性能研究

为提高TiO_2纳米管阵列(TiO_2-NTs)的可见光活性,通过阳极氧化和热分解法制备了Fe_2O_3纳米粒子修饰的TiO_2纳米管阵列(Fe_2O_3/TiO_2-NTs)。通过扫描电子显微镜(SEM),透射电子显微镜(TEM)和紫外-可见光漫反射光谱(UV-vis DRS)等对产物进行了相关表征,同时测试了产物的光电性能及其光催化降解甲基橙的性能。结果显示,Fe_2O_3/TiO_2-NTs的光电流强度和光催化降解率分别是是TiO_2-NTs的19倍和8.7倍。     

可磁分离的氮掺杂二氧化钛光催化剂的制备及光催化性能

将氮掺杂二氧化钛和通过液相催化相转化制备的磁性载体混合、煅烧制备了一种可磁分离的光催化剂TiO2-xNx/SiO2/NiFe2O4(TSN), 这种光催化剂显示出了典型的铁磁性和可见光活性(λ>400 nm). 对该光催化剂的XRD谱图和透射电镜照片进行分析. 结果表明, SiO2/NiFe2O4(SN)纳米粒子黏附在TiO2-xNx聚集体的表面形成了TSN复合光催化剂. 利用光催化降解甲基橙的效果来评价这种光催化剂的活性. 结果表明, 在NiFe2O4和TiO2-xNx之间包覆一层无定形的SiO2, 可以显著地提高催化剂的脱色效果.     

介孔TiO2的水热法制备及其光催化性能

以二钛酸钾(K2Ti2O5)经离子交换得到的无定形水合二钛酸(H2Ti2O5·xH2O)为原料, 与葡萄糖溶液在220 ℃下进行水热反应, 再在空气中520 ℃焙烧, 制备出介孔TiO2. 用扫描电子显微镜(SEM)、X射线衍射(XRD)、N2吸附、透射电子显微镜(TEM)等技术对样品进行了表征. 结果表明, 该介孔TiO2具有微米级棒状或针状形貌, 晶粒大小为12.3 nm, 比表面积为106 m2·g-1, 孔容为0.31 cm3·g-1, 孔径为8.06 nm, 焙烧处理后晶型仍是锐钛矿相. 水热生成的碳抑制了晶粒的团聚生长和晶型的转变, 提高了介孔TiO2的热稳定性. 甲基橙降解实验评价了介孔TiO2的光催化性能, 结果发现其活性与商用TiO2催化剂P25相当, 而其较大的粒径更容易回收再利用. 以碘化钾为探针反应, 表明介孔TiO2的光催化机制以光生空穴氧化为主.     

Fe2O3/TiO2纳米管的制备及其光电催化降解染料废水性能

采用阴极电沉积和阳极氧化法制备了Fe2O3改性TiO2纳米管(Fe2O3/TiO2-NTs)电极,运用场发射扫描电子显微镜、透射电子显微镜、X射线衍射和紫外-可见漫反射光谱等手段对其进行了表征,考察了其光电化学性能,并研究了复合电极光电催化降解甲基橙染料废水的反应性能.结果表明,Fe2O3的负载成功地将TiO2-NTs的光响应区间拓宽到可见光区域,Fe2O3/TiO2-NTs复合电极的光电流密度达到TiO2-NTs电极的3倍.在光电催化反应中,Fe2O3/TiO2-NTs复合电极对甲基橙的脱色效果明显优于TiO2-NTs电极,以Fe2O3/TiO2-NTs为阳极,光照5min,甲基橙溶液的脱色率可达90%以上.     

ZnO纳米管的光学性质及其对甲基橙降解的光催化活性

以十二烷基硫酸钠为模板剂采用水热法合成了ZnO纳米管,以尿素和ZnSO4为原料制备了ZnO纳米颗粒,并应用透射电镜、x射线衍射、光致发射光谱、拉曼光谱、比表面积测定、傅里叶红外光谱和紫外-可见漫反射光谱等技术对样品进行了表征.结果表明,ZnO纳米管的比表面积较大,在λ≈650nm的可见光波段ZnO纳米管开始出现吸收峰,而ZnO纳米颗粒在可见光波段几乎没有吸收.ZnO纳米管和纳米颗粒在紫外光照射下均对甲基橙有降解作用,其中ZnO纳米管的光催化活性较高.随着催化剂用量的增加和光照时间的延长,甲基橙降解率逐渐提高;甲基橙浓度的增大使甲基橙降解率降低.     

用高温热水解法制备高活性TiO2纳米微晶光催化剂

采用钛酸四西酯在有机溶剂中高温热水解与结晶同时进行的方法，制备了二氧化钛纳米微晶光催化剂．以XRD、BET、TEM、TG和DTA等方法对获得的微晶进行了表征．所制得的TiO2纳米微晶平均值径约为12nm，比表面积在100m2·g-1以上，并能在报宽的煅烧温度范围内保持锐钛矿型晶体结构．将它应用于光分解甲基橙，具有高的光催化活性．     

微乳法制备纳米TiO2 /SiO2的结构及光催化研究

Nanosized TiO₂ and TiO₂/SiO₂ particles were prepared by hydrolysis of tetrabutyl titanate (TBOT) and tetraethyl orthosilicate (TEOS) in the TX-100 reverse microemulsion. These particles were characterized by TG-DSC, XRD, FTIR, TEM，N₂ adsorption-desorption. Their photocatalytic activity was tested by degradation of methyl orange. The result shows that TiO₂/SiO₂ nanoparticles are with a monodispersed spherical phase and a uniform size distribution，and TiO₂ particles are dispersed on the surface of SiO₂. The band for Ti-O-Si vibration in FTIR was observed, the Ti-O-Si bond increased the stability of anatase TiO₂, suppressed the phase transformation of titania from anatase to rutile. And due to the addition of SiO₂, the average size of titania decreased from 38 nm in pure TiO₂ to 5 nm in TiO₂/SiO₂. It was found, under UV light irradiation, TiO₂/SiO₂ particles showed higher activity than pure TiO₂, and TiO₂/SiO₂(1/1) particles showed the highest photocatalytic activity on the photocatalytic decomposition of methyl orange, which was influenced by crystal structure, particle size, crystallinity and Surface area Characteristics.     

表面活性剂辅助水热合成氧化钛纳米针溶胶

TiO₂ nanoneedles sol with particle size of 10～15 nanometer was synthesized by hydrothermal method using peroxo titanic acid as the precursor, cetyltrimethyl ammonium bromide(CTAB) as the surfactant. The product was characterized by XRD, TEM, HRTEM and selected area electron diffraction(SAED). The results show that the as-prepared products have high crystallinity and grow along the c-axis, with homogeneous morphology and good monodispersity. In addition, TiO₂ hydrosol possessed good photocatalytic activity for the photocatalytic degradation of methyl orange aqueous solution under the sunlight illumination.     

TiO2/SiO2复合材料的制备与表征

以钛酸四丁酯和正硅酸乙酯为原料,采用溶胶凝胶法和水解法相结合,在室温下制备了两种形态的TiO2/SiO2复合材料.采用透射电镜、傅里叶红外光谱、X射线衍射和紫外-可见光谱等测试方法对所得复合材料进行了表征,并对其光催化降解甲基橙溶液的性能进行了研究.结果表明:对TiO2进行表面处理制备的TiO2/SiO2复合材料比以SiO2为载体制备的TiO2/SiO2复合材料在光催化和抗紫外线性能上更优异.     

模拟太阳光下稀土Gd掺杂TiO2纳米晶的光催化性能研究

以甲基橙的光催化降解为探针反应,采用氙灯模拟自然条件下的太阳光,评价了通过酸催化的溶胶-凝胶法制备的稀土Gd掺杂改性TiO₂纳米晶的光催化活性及对甲基橙水溶液TOC的去除效果.运用XRD和UV-Vis DRS表征技术考察了Gd掺杂对纳米TiO₂的微晶尺寸、晶体结构与光学性能的影响.结果表明,Gd掺杂可以抑制TiO₂由锐钛矿相向金红石相的转变,阻碍TiO₂晶粒增长,使TiO₂的光吸收带边发生蓝移且有利于对可见光的吸收,从而使Gd掺杂TiO₂在模拟太阳光下光催化降解甲基橙的能力得到明显提高,但样品对甲基橙水溶液TOC的去除效果要滞后于其对色度的去除.