乙炔在钒催化体系下的聚合

本工作采用三乙酰基丙酮钒及二乙酰基氧钒同烷基铝组成的催化体系,研究了乙炔聚合的规律及聚乙炔成膜的条件,并初步研究了聚乙炔膜的链节结构、形态结构及室温电导率。     

Electrochemical properties of conducting polyethylene-polyacetylene composites

Production techniques, structure, and electrochemical properties of conducting thin-film materials consisting of a polyethylene (PE) substrate covered with a polyacetylene (PA) layer are studied. Properties of a free PA film are determined by the catalyst used in its synthesis. Properties of composites depend on the optimum selection of the PA/PE ratio (by weight), the catalyst used for polymerizing PA, and the PE structure. The capacity of composites is higher than that of free PA films. This points to the possible role of an increased transport of lithium cations at interfaces.     

用无乳化剂乳液聚合法制备聚丙烯醛微球

本文应用无乳化剂乳液聚合法合成了粒度均一、具有活泼醛基的聚丙烯醛微球,并对丙烯醛聚合动力学和影响微球直径,活泼醛基含量的因素进行了研究。用合成的微球同不同的氨基酸和午血清白蛋白反应,结果表明:该微球在生理pH条件下同含有伯氨基的化合物具有较高的结合容量。因此,在无乳化剂存在下,采用乳液聚合法制备聚丙烯醛微球是一种合成具有干净表面的聚丙烯醛微球的新方法。     

高强度高电导率聚乙炔的合成——醚类溶剂的结构对性能的影响

通过选用不同醚类结构做溶剂加热回流Ti(OBu)_4-AIEt_3催化剂,并采用非溶剂聚合方法进行乙炔聚合发现,所得HPPA膜的强度和电导率都有了较大提高。其中直链醚制得的PA膜强度(抗张强度大于100MPa)和空气稳定性比用环醚得到的PA膜高得多,但用前者时的乙炔聚合速率远低于后者。两体系得到的HPPA膜的碘掺杂电导率值相近(～10~3S/cm),拉伸后可达10~4S/cm量级。SEM、TEM及IR光谱的结果表明,不同醚制得的PA膜的纤维束直径及顺式含量有较大差别。     

双金属氰化络合物催化环氧丙烷和邻苯二甲酸酐共聚

采用双金属氰化络合物 (DMC)催化环氧丙烷 (PO)和邻苯二甲酸酐 (PA)共聚 ,探讨了共聚合特征 ,并用IR、1 H NMR和GPC对共聚物的结构和分子量进行了表征 .发现DMC催化剂对该共聚反应速度快 ,转化率高 ,是该反应的有效催化剂 ,催化剂浓度为 6 0mg kg时 ,90℃下 ,以THF作溶剂共聚反应 3h ,转化率可达94 0 % .聚合速度甚至比DMC催化PO均聚还快 .该共聚反应可在多种溶剂中进行 ,极性溶剂更有利于共聚合 ,溶液聚合温度比本体共聚低 ,合适的溶液共聚温度在 90～ 10 0℃之间 .共聚产物的分子量受催化剂用量、反应温度和体系中水份含量的影响 ,数均分子量在数百至数千之间 .考察该共聚体系的动力学表明 ,该共聚反应速率对单体浓度呈一级关系     

MoO3催化碳酸二甲酯与乙酸苯酯合成碳酸二苯酯

采用焙烧法制备了MoO3催化剂并将其用于碳酸二甲酯(DMC)与乙酸苯酯(PA)合成碳酸二苯酯(DPC)反应,考察了焙烧温度对催化荆性能的影响,并用X射线衍射(XRD)对催化剂结构进行了表征.结果发现,在400或500℃焙烧的催化剂具有良好的催化性能,DMC转化率为73.9%,DPC和甲基苯基碳酸酯的选择性分别为39.5%和56.5%.XRD结果表明,该催化剂物相组成为正交晶系MoO3,且(021)或/和(110)晶面有利于酯交换反应.催化剂使用5次后DMC转化率从73.9%降至10.2%,多次重复使用后的催化剂在窄气气氛中于400或500℃焙烧即可再生,再生后催化剂的性能几乎和新鲜催化剂相当.     

稀土对钒—钛苯酐催化剂活性的影响

在邻二甲苯气相氧化制苯酐的Ｖ２Ｏ５－ＴｉＯ２催化剂中，添加少量Ｌａ、Ｐｒ、Ｓｍ或Ｎｄ后，催化剂活性有不同程度的提高。本文应用ＦＴ－ＩＲ研究了氧化有后的苯酐催化剂，明显观察到在Ｖ－Ｔｉ苯酐催化剂中添加稀土后，Ｖ－Ｏ键的吸收峰发生红移，最大红移达到２３５ｃｍ＾－１。苯酐催化剂加入稀土后，对分子的活化作用与催化活性剂评价的结果是一致的。     

高活性载体Ziegler-Natta催化剂的研究

<正> 用反应法(MgCl_2/ROH/TiCl_4)合成MgCl_2载体Ziegler-Natta催化剂已被聚烯焊工业越来越广泛的接受。这不仅是因为这种催化剂体系具有高活性,用于α-烯烃聚合能得到高等规度的聚合物;而且比用研磨法制备催化剂易于控制操作条件,合成这种催化剂的关键步骤是醇溶解MgCl_2,再在低温下与TiCl_4反应。放出HCl和形成Ti(OR)Cl_3的同时,MgCl_2再次从溶液中沉淀出来而得到很好的载体。过去,曾从不同     

可溶性稀土聚乙炔的合成及其聚合机理的研究

研究了各种催化体系、催化剂浓度及聚合条件对催化效率(f)和聚乙炔分子量()的影响。发现Nd(i-OC_3H_7)-AlR_3(R=C_2H_5,i-C_4H_9)催化体系可获得较大的可溶分数(q)。催化剂浓度、Al/Nd克分子比和聚合温度对f、及q均有一定影响。可溶性Nd(i-OC_3H_7)_3-AlR_3催化体系的UV光谱证实、Nd的价态与AlR_3混合与AlR_3混合后保持不变。PA的IR光谱示出,Nd(i-OC_3H_7)_3-Al(C_2H_5)_3及Nd(i-OC_3H_7)_3-Al(i-C_4H_9)_3体系获得的聚合物分别含有CH_3CH_2—和(CH_3)_2CHCH_2—末端基。上述结果表明,乙炔的聚合可能是通过单体在Nd-C键之间的插入进行的。     

Recyclable helical poly(phenylacetylene)‐supported catalyst for asymmetric aldol reaction in aqueous media

A novel one‐handed helical poly(phenylacetylene) bearing L‐hydroxyproline pendants (poly(PA‐P)) was synthesized as an eco‐friendly polymer‐supported catalyst for asymmetric reactions. The helical poly(PA‐P) catalyzed the asymmetric aldol reactions of cyclohexanone with p‐nitrobenzaldehyde, and showed good recyclability and higher enantiomeric excess (ee) in aqueous medias than that in organic medias. The one‐handed helicity of poly(PA‐P) was clearly affected by the water content in the aqueous media. The helical poly(PA‐P) showed the higher enantioselectivity (ee = 99%) than its monomer PA‐P (ee = 54%) in THF/H₂O (H₂O vol % = 25.0 vol %). After the one‐handed helical structure of poly(PA‐P) was destroyed by grinding treatment, the ee of the reaction clearly decreased from 99 to 49%. These indicate that the one‐handed helical structure of poly(PA‐P) played an important role in the high enantioselectivity of the asymmetric aldol reactions in the aqueous media. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1024–1031     

Kinetic studies of polyamide-imide synthesis

To understand the kinetic of synthesis of polyamide-imide (PAI) via p-chlorophenol-(PCP) blocked 4,4′-diphenyl methane diisocyanate (MDI) with trimellitic anhydride (TMA), a series of reactions of blocked MDI with excess phthalic anhydride (PA) and benzoic acid are designed. PCP-blocked phenyl isocyanate (BPI) which also released isocyanate at higher temperatures was used as a model compound for BMDI. The dissociation constants of BPI and BMDI in the presence of excess PA or BA was measured by collecting the evolved CO₂. The effect of the catalyst concentration and temperatures were combined by a Hostettler equation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1703–1710, 1997     

Performance enhancement of phosphoric acid-based proton exchange membrane fuel cells by using ammonium trifluoromethanesulfonate

In a fuel cell system where concentrated phosphoric acid (PA) is used as a proton conducting medium, the use of PA causes some undesirable effects on oxygen reduction reaction (ORR) at Pt catalyst. Ammonium trifluoromethanesulfonate (ATFMS) is introduced as a cathode additive to increase the local oxygen concentration near the Pt catalyst. A cathode with the optimum composition of ATFMS shows a higher single cell performance than that without the additive when a single cell based on a PA-doped polymer membrane is operated at 150 °C. The enhanced ORR activity and oxygen solubility with the incorporation of ATFMS are proved with rotating disk electrode (RDE) and Pt microelectrode experiments. Single cell performance for longer than 600 h without decay in operating voltage could support the stability of the additive.     

可溶性稀土聚乙炔的某些结构特征

本文利用UV、IR、Ramaan、ESR和X射线衍射等方法研究了可溶性聚乙炔的某些结构特征。发现非结晶的可溶性聚乙炔的光谱和波谱性质与结晶的膜状及粉末状聚乙炔有明显的差异,可能是由于它们的分子量相差悬殊造成的。实验结果表明,线型聚乙炔可能存在可溶的临界分子量,其值在=500 左右。     

Synthesis of triblock copolymers—(polyA-poly butadiene-polyA)—via metathesis polymerization

A series of triblock copolymers of the type A-B-A were synthesized using tungsten chloride-anchored hydroxyl-terminated polybutadiene (HTPBD) catalyst. Monomers like phenylacetylene (PA), norbornene (NBE), cyclooctadiene (COD), and cyclopentene (CP) were polymerized via metathesis pathway using this catalyst. The efficiency of this anchored catalyst in producing A-B-A triblock copolymers was explored and compared under the same experimental conditions like solvent system and reaction temperature. This anchored catalyst upon reaction with PA produced polyPA-block-polyBD-block-polyPA in high yield and with low polydispersity (pdi) compared to HTPBD. The formation of the triblock copolymers by this method was evinced by NMR, TGA, and GPC data as well as by delinking and inverse addition studies. All the cycloalkenes polymerized via ring-opening metathesis polymerization (ROMP) with the catalyst and yielded triblock copolymers. The mode of synthesis of triblocks could be construed as switching the mechanism of polymerization from radical to olefin metathesis. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2601–2610, 1998     

Ozone interaction with conjugated polymers—I. Polyacetylene

Free-standing films of cis- and trans-rich polyacetylene (PA) obtained on a Rh(I) catalyst, were treated with ozonized oxygen (O₃ 1% by weight on average). The initial superficial charge-transfer complex formed between ozone and the polyene chain and the subsequent ozone accelerated cis-trans isomerization were studied by electronic and FT-IR spectroscopies. A peculiar mechanism of interaction between ozone and polyenic chain was proposed, and cation radicals were observed on the ozone doped surfaces of PA. Ozone treatment of PA films creates a superficial oxidized barrier that prevents subsequent thermo-oxidative destruction of the bulk portion of PA film. This treatment could be a way of protecting PA from degradative oxidation.     

Acid-base chemistry of a carbenium ion in a zeolite under equilibrium conditions: verification of a theoretical explanation of carbenium ion stability

The 1,3-dimethylcyclopentenyl carbenium ion (C7H11(+)) was reproducibly prepared on zeolite HZSM-5 using a pulse-quench reactor, and then each of a number of bases was coadsorbed into the catalyst channels to either compete with the cation for protonation or to possibly react with it as a nucleophile. For seven bases with proton affinities (PA) between 142 and 212.1 kcal/mol, there was no reaction with C7H11(+). Coadsorption of smaller amounts of dimethylacetamide (PA = 217 kcal/mol) also produced no reaction, but with a higher loading, a proton was transferred from the carbenium ion to the base to leave 1,3-dimethylcyclopenta-1,3-diene in the zeolite as a neutral olefin. Deprotonation was the primary reaction with coadsorption of either pyridine (PA = 222 kcal/mol) or trimethylphosphine (PA = 229.2 kcal/mol). The estimated experimental deprotonation enthalpy for C7H11(+), approximately 217 kcal/mol in the zeolite, is in excellent agreement with MP4/6-311G gas-phase value of 215.6 kcal/mol. Coadsorption of either NH3 (PA = 204.0 kcal/mol) or PH3 (PA = 188 kcal/mol) does not deprotonate the carbenium ion, but these species do react as nucleophiles to form onium ion derivatives of C7H11(+). Analogous onium complexes with pyridine or trimethylphosphine formed in lower yields due to steric constraints in the zeolite channels. The essential experimental observations were all predicted and explained by density functional calculations (B3LYP/6-311G) and extensions of our recently developed theory of carbenium ion stability in zeolites. In addition, we report theoretical geometries for several complexes which contain unusual C-H- - -X hydrogen bonds.     

Single‐Component Phosphinous Acid Ruthenium(II) Catalysts for Versatile C−H Activation by Metal–Ligand Cooperation

Well‐defined ruthenium(II) phosphinous acid (PA) complexes enabled chemo‐, site‐, and diastereoselective C?H functionalization of arenes and alkenes with ample scope. The outstanding catalytic activity was reflected by catalyst loadings as low as 0.75 mol %, and the most step‐economical access reported to date to angiotensin II receptor antagonist blockbuster drugs. Mechanistic studies indicated a kinetically relevant C?X cleavage by a single‐electron transfer (SET)‐type elementary process, and provided evidence for a PA‐assisted C?H ruthenation step.     

Preparation and Thermal Properties of Polycarbonates/esters Catalyzed by Using Dinuclear Salph‐Al from Ring‐Opening Polymerization of Epoxide Monomers

A dinuclear Salph‐Al complex/bis(triphenylphosphine)iminium chloride catalyst system was synthesized and employed for cyclohexene oxide (CHO) and CO₂ copolymerization. The catalyst system had an excellent selectivity of 99 % for carbonate linkages and the resultant poly(cyclohexene carbonate) (PCHC) had a high glass transition temperature (T _g) of 123.8 °C and a thermal decomposition temperature (5 % weight loss; T _{d 5 %}) of 265 °C. Furthermore, this catalyst system was active in the polymerization of phthalic anhydride (PA) and epoxides. Poly(CHO‐alt ‐PA) was completely alternating, and had improved thermal properties (T _g=142.7 and T _{d 5 %}=295 °C) compared with PCHC. The T _g values of the polyesters could be adjusted by addition of PO to the CHO/PA reaction system. For the CHO/PO/PA terpolymerization, CHO and PO participated concurrently and proportionally in the chain growth and the obtained terpolyesters had tunable T _g values from 62.8 to 142.7 °C depending on the CHO/PO feed ratio.     

Trinuclear salphen–chromium(III)chloride complexes as catalysts for the alternating copolymerization of epoxides and cyclic anhydrides

Although the alternating copolymerization of epoxides and cyclic anhydrides is a promising route to aliphatic polyesters, improved catalysts are required to realize commercialization of this process. Herein, trinuclear chromium complexes of salicylaldimine, in conjunction with a nucleophilic cocatalyst, are demonstrated as excellent catalysts for epoxide/cyclic anhydride copolymerization, selectively affording perfectly alternating polyesters. The effect of the distance between the chromium species is investigated by varying the bridging skeleton in a series of trinuclear salphen–Cr(III)Cl complexes for obtaining different Cr–Cr distances. Trinuclear salphenCr(III)–complexes with Cr–Cr distances of approximately 7.3 Å are found to be efficient copolymerization catalysts, even at high temperatures and extremely low catalyst loadings. In particular, a high activity of 10,620 h⁻¹ is obtained for the copolymerization of cyclohexene oxide (CHO) and phthalic anhydride (PA) under a low catalyst loading (<0.01 mol%) at 100 °C. In situ infrared spectroscopy studies suggest that the activation energy of the trinuclear Cr(III)–salphen catalyst for CHO/PA copolymerization is 15 kJ mol⁻¹ lower than that of the corresponding mononuclear catalyst owing to an intramolecular synergistic effect among the metal atoms.     

1,4-丁炔二醇的均聚及与苯乙炔的共聚研究

<正> 炔类聚合物由于具有长链π体系的结构特点,理论上可作为结构型导电聚合物,这一领域的研究工作正在迅速展开。 1,4-丁炔二醇(BD)可用PdCl_2,ZnCl_2,(Ph_3P)_2PdCl_2等多种催化剂催化聚合,得到长链共轭的聚(1,4-丁炔二醇)(PBD)。苯乙炔(PA)可用热聚合,光聚合、电聚合、自由基聚合、等离子体聚合、催化聚合等聚合方法,得到长链共轭的聚苯乙炔