Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Electrospinning preparation of one-dimensional Co<Superscript>2+</Superscript>-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers for high-performance lithium ion battery

One-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofibers with a diameter of approximately 500 nm have been synthesized via a one-step controllable electrospinning method. The Co²⁺-doped Li₄Ti₅O₁₂ nanofibers were systematically characterized by XRD, ICP, TEM, SEM, BET, EDS mapping, and XPS. Based on the cubic spinel structure and one-dimensional effect of Li₄Ti₅O₁₂, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers exhibit the enlarged lattice volume, reduced particle size and enhanced electrical conductivity. More importantly, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers as a lithium ion battery anode electrode performs superior electrochemical performance than undoped Li₄Ti₅O₁₂ electrode in terms of electrochemical measurements. Particularly, the reversible capacity of Co²⁺-doped Li₄Ti₅O₁₂ electrode reaches up to 140.1 mAh g^?1 and still maintains 136.5 mAh g^?1 after 200 cycles at a current rate of 5 C. Therefore, one-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofiber electrodes, showing high reversible capacity and remarkable recycling property, could be a potential candidate as an anode material.     

Nano Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> as sulfur host for high-performance Li-S battery

S/Li₄Ti₅O₁₂ cathode with high lithium ionic conductivity was prepared for Li-S battery. Herein, nano Li₄Ti₅O₁₂ is used as sulfur host and fast Li⁺ conductor, which can adsorb effectively polysulfides and improve remarkably Li⁺ diffusion coefficient in sulfur cathode. At 0.5 C, S/Li₄Ti₅O₁₂ cathode has a stable discharge capacity of 616 mAh g^?1 at the 700th cycle and a capacity loss per cycle of 0.0196% from the second to the 700th cycle, but the corresponding values of S/C cathode are 437 mAh g^?1 and 0.0598%. Even at 2 C, the capacity loss per cycle of S/Li₄Ti₅O₁₂ cathode is only 0.0273% from the second to the 700th cycle. The results indicate that Li₄Ti₅O₁₂ as the sulfur host plays a key role on the high performance of Li-S battery due to reducing the shuttle effect and enhancing lithium ionic conductivity.     

Influence of post-calcination treatment on the spinel lithium titanium oxide anode material for lithium ion batteries

The influence of post-calcination treatment on spinel Li₄Ti₅O₁₂ anode material is extensively studied combining with a ball-milling-assisted rheological phase reaction method. The post-calcinated Li₄Ti₅O₁₂ shows a well distribution with expanded gaps between particles, which are beneficial for lithium ion mobility. Electrochemical results exhibit that the post-calcinated Li₄Ti₅O₁₂ delivers an improved specific capacity and rate capability. A high discharge capacity of 172.9 mAh g^?1 and a reversible charge capacity of 171.1 mAh g^?1 can be achieved at 1 C rate, which are very close to its theoretical capacity (175 mAh g^?1). Even at the rate of 20 C, the post-calcinated Li₄Ti₅O₁₂ still delivers a quite high charge capacity of 124.5 mAh g^?1 after 50 cycles, which is much improved over that (43.9 mAh g^?1) of the pure Li₄Ti₅O₁₂ without post-calcination treatment. This excellent electrochemical performance should be ascribed to the post-calcination process, which can greatly improve the lithium ion diffusion coefficient and further enhance the electrochemical kinetics significantly.     

Pr-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers as an anode material for lithium-ion batteries with outstanding cycling performance and rate performance

Pr-doped Li₄Ti₅O₁₂ in the form of Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0, 0.01, 0.03, 0.05, and 0.07) was synthesized successfully by an electrospinning technique. ICP shows that the doped samples are closed to the targeted samples. XRD analysis demonstrates that traces of Pr³⁺ can enlarge the lattice parameter of Li₄Ti₅O₁₂ from 8.3403 to 8.3765 Å without changing the spinel structure. The increase of lattice parameter is beneficial to the intercalation and de-intercalation of lithium-ion. XPS results identify the existence form of Ti is mainly Ti⁴⁺ and Ti³⁺ in minor quantity in Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples due to the small amount of Pr³⁺. The transition from Ti⁴⁺ to Ti³⁺ is conducive to the electronic conductivity of Li₄Ti₅O₁₂. FESEM images show that all the nanofibers are well crystallized with a diameter of about 200 nm and distributed uniformly. The results of electrochemical measurement reveal that the 1D Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) nanofibers display enhanced high-rate capability and cycling stability compared with that of undoped nanofibers. The high-rate discharge capacity of the Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples is excellent (101.6 mAh g^?1 at 50 °C), which is about 58.48 % of the discharge capacity at 0.2 °C and 4.3 times than that of the bare Li₄Ti₅O₁₂ (23.5 mA g^?1). Even at 10 °C (1750 mA g^?1), the specific discharge capacity is still 112.8 mAh g^?1 after 1000 cycles (87.9 % of the initial discharge capacity). The results of cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) illustrate that the Pr-doped Li₄Ti₅O₁₂ electrodes possess better dynamic performance than the pure Li₄Ti₅O₁₂, further confirming the excellent electrochemical properties above.     

Synthesis of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>-reduced graphene oxide composite and its application for hybrid supercapacitors

We describe in this paper the synthesis and the characterization of Li₄Ti₅O₁₂-reduced graphene oxide (LTO-RGO) composite and demonstrate their use as hybrid supercapacitor, which is consist of an LTO negative electrode and activate carbon (AC) positive electrode. The LTO-RGO composites were synthesized using a simple, one-step process, in which lithium sources and titanium sources were dissolved in a graphene oxide (GO) suspension and then thermal treated in N₂. The lithium-ion battery with LTO-RGO composite anode electrode revealed higher discharge capacity (167 mAh g^?1 at 0.2 C) and better capacity retention (67%) than the one with pure LTO. Meanwhile, compared with the AC//LTO supercapacitor, the AC//LTO-RGO hybrid supercapacitor exhibits higher energy density and power density. Results show that the LTO-RGO composite is a very promising anode material for hybrid supercapacitor.     

Improvement electrochemical performance of Li1.5Ni0.25Mn0.75O2.5 with Li4Ti5O12 coating

Layered cathode Li_1.5Ni_0.25Mn_0.75O_2.5 has been synthesized and coated by Li₄Ti₅O₁₂. The pristine and coated Li_1.5Ni_0.25Mn_0.75O_2.5 powders are characterized by X-ray diffraction (XRD), indicating the materials remained the layered structure before and after coating. The coated Li₄Ti₅O₁₂ has been detected by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (DEX). The electrochemical performance, especially rate performance of Li_1.5Ni_0.25Mn_0.75O_2.5 electrode, is improved effectively after Li₄Ti₅O₁₂ coating. The first discharge capacity, coulombic efficiency, and capacity retention of Li₄Ti₅O₁₂-coated Li_1.5Ni_0.25Mn_0.75O_2.5 electrode are 244 mA h g^?1, 81.5 %, and 98.3 % after 50 cycles, respectively. The Li₄Ti₅O₁₂-coated Li_1.5Ni_0.25Mn_0.75O_2.5 electrode exhibits 108 mA h g^?1 at 10 °C rate. Electrochemical impedance spectroscopy (EIS) results show that the charge transfer resistance (R _ct) of Li_1.5Ni_0.25Mn_0.75O_2.5 electrode decreases after coating, which is due to the existence of Li₄Ti₅O₁₂ with high lithium ion diffusion coefficient and suppression of the solid electrolyte interfacial (SEI) layer development and is responsible for the excellent rate capability and cyclic performance.     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Preparation and characteristics of Li4Ti5O12 with various dopants as anode electrode for hybrid supercapacitor

Spinel-Li₄Ti₅O₁₂ is successfully synthesized by a solid phase synthesis. The Li₄Ti₅O₁₂ powders with various dopants (Al³⁺, Cr³⁺, Mg²⁺) synthesized at 800 °C are in accordance with the Li₄Ti₅O₁₂ cubic spinel phase structure. The dopants are inserted into the lattice structure of Li₄Ti₅O₁₂ without causing any changes in structural characteristics. In order to study the effect on various dopants, the hybrid supercapacitor is prepared by using un-doped Li₄Ti₅O₁₂ and doped Li₄Ti₅O₁₂ in this work. The electrochemical performance of the hybrid supercapacitor is characterized by impedance spectroscopy and cycle performance. The results show Cr³⁺ and Mg²⁺ dopants enhance the conductivity of Li₄Ti₅O₁₂. Also, Al³⁺ substitution improves the reversible capacity and cycling stability of Li₄Ti₅O₁₂. It is found that effect of dopant on the electrochemical performance of Li₄Ti₅O₁₂ as electrode material for hybrid supercapacitor where the EDLC and the Li ion secondary battery coexist in one cell system.     

Enhanced high-rate performance of sub-micro Li4Ti4.95Zn0.05O12 as anode material for lithium-ion batteries

Zn-doped Li₄Ti₅O₁₂ was prepared by a ball milling-assisted solid-state method, and the characters were determined by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, cyclic voltammetry, and galvanostatic charge–discharge testing. The results show that Li₄Ti_5?x Zn _x O₁₂ (x?=?0, 0.05) exhibits the pure phase structure, and Zn doping does not change the electrochemical reaction process and basic spinel structure of Li₄Ti₅O₁₂. The particle size of both samples is about 300–500 nm. The prepared Li₄Ti_4.95Zn_0.05O₁₂ presents an excellent rate capability and capacity retention. At the charge–discharge rate of 1C, the initial discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is 268 mAh g^?1. After 90 cycles at 5C, the discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is obviously higher than that of Li₄Ti₅O₁₂. The excellent electrochemical performance of the Li₄Ti_4.95Zn_0.05O₁₂ electrode could be attributed to the improvement of reversibility by doping zinc and the sub-micro particle size.     

A new composite material Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>–SnO<Subscript>2</Subscript> for lithium-ion batteries

A new Li₄Ti₅O₁₂–SnO₂ composite anode material for lithium-ion batteries has been prepared by loading SnO₂ on Li₄Ti₅O₁₂ to obtain composite material with improved electrochemical performance relative to Li₄Ti₅O₁₂ and SnO₂. The composite material was characterized by X-ray diffraction and scanning electron microscopy. The results indicated that SnO₂ particles have encapsulated on the surface of the Li₄Ti₅O₁₂ uniformly and tightly. Electrochemical results indicated that the Li₄Ti₅O₁₂–SnO₂ composite material increases the reversible capacity of Li₄Ti₅O₁₂ and has good cycling reliability. At a current rate of 0.5 mA/cm², the material delivered a discharge capacity of 236 mAh/g after 16 cycles. It suggests the existence of synergistic interaction between Li₄Ti₅O₁₂ and SnO₂ and that the capacity of the composite is not a simple weighted sum of the capacities of the individual components. In the composite material, SnO₂ can act as a bridge between the spinel particles to reduce the interparticle resistance and as a good material for the Li intercalation/deintercalation. Thus, electrochemical performance of the Li₄Ti₅O₁₂ spinel can be improved by the surface modification with SnO₂, and the stability of Li₄Ti₅O₁₂ also serves to buffer the internal stress caused by the volume changes in lithium insertion and extraction reactions.     

Preparation of carbon encapsulated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium ion battery through pre-coating method

Carbon encapsulated Li₄Ti₅O₁₂ (C/Li₄Ti₅O₁₂) anode material for lithium ion battery was prepared by using the pre-coat method of two steps, and the TiO₂ was pre coated before the reaction with Li₂CO₃. The structure and morphology of the resultant C/Li₄Ti₅O₁₂ materials were characterized by X-ray diffraction (XRD) and scanning microscopy (SEM). Electrochemical tests showed that at 0.1 C, the initial discharge capacity was 169.9 mAh g^?1, and the discharge capacity was 80 mAh g^?1 at 5 C. After 100 cycles at 2 C, the discharge specific capacity was 108.5 mAh g^?1. Compare with one step coating method, results showed the C/Li₄Ti₅O₁₂ prepared by pre-coat method can reduce the particle’s size and effectively improve the electrochemical performance.     

Advanced electrochemical performances of Li4Ti5O12/Ag prepared by a facile synthesis route

Spinel Li₄Ti₅O₁₂ coated by highly dispersed nanosized Ag particles was synthesized via a facile and effective ultrasonic-assisted method in this paper. X-ray diffraction (XRD) results indicated that Ag was not doped into the lattice of spinel Li₄Ti₅O₁₂. The as-synthesized Li₄Ti₅O₁₂/Ag exhibited enhanced electronic conductivity and excellent electrochemical performances. Its electronic conductivity was increased about four times compared to that of the pristine Li₄Ti₅O₁₂. Even at 10 C rate, the as-synthesized Li₄Ti₅O₁₂/Ag could keep 86.5 % of the reversible capacity at 1 C rate and its reversible capacity was higher than 140 mAhg^?1 whereas those were 75.3 % and 118 mAhg^?1 for the pristine Li₄Ti₅O₁₂.     

Solid-state synthesis of graphite carbon-coated Li4Ti5O12 anode for lithium ion batteries

Graphites are widely used for their high electrical conductivity and good thermal and chemical stability. In this work, graphitic carbon-coated lithium titanium (Li₄Ti₅O₁₂/GC) was successfully synthesized by a simple one-step solid-state reaction process with the assistance of sucrose without elevating sintering temperature. The lattice fringe of 0.208 nm clearly seen from the high-resolution transmission electron microscopy (HRTEM) images was assigned to graphite (010). The average grain size of the as-prepared Li₄Ti₅O₁₂/GC was about 100–200 nm, 1 order smaller than that of pure Li₄Ti₅O₁₂ prepared similarly. The rate performance and cycle ability were significantly improved by the hybrid conducting network formed by graphitic carbon on the grains and amorphous carbon between them. The specific capacity retention rate was 66.7 % when discharged at a rate of 12C compared with the capacity obtained at 0.5C. After 300 cycles, the capacity retention was more than 90 % at a high rate of 15C.     

Kinetic performance of Li4Ti5O12 anode material synthesized by the solid-state method

Li₄Ti₅O₁₂ anode was successfully synthesized by solid-state method. X-ray diffraction and scanning electron micrographs show that Li₄Ti₅O₁₂ prepared by solid-state method has a purity phase with a uniform particle size in the range of 0.5?C1???m. Cyclic voltammogram reveals that there is a big irreversible capacity for the first cycle. Li₄Ti₅O₁₂ shows a stable cycling stability at 1?C rate. After 152 cycles, the discharge capacity is 213?mAh?g^?1, which keeps 93% of it at the second cycle. Electrochemical impedance spectroscopy shows that the resistance of charge-transfer of Li₄Ti₅O₁₂ electrode decreased with increasing the storage temperatures, and the lithium diffusion coefficient is increased with increasing the storage temperatures, revealing that the kinetics of Li⁺ and electron transfer into the electrodes were much faster at high temperature than that at low temperature. The apparent activation energy of the charge transfer and lithium diffusion can be calculated to be 33.1 and 27.3?kJ?mol^?1, respectively.     

Titanium-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> with a synergistic effect of surface modifying,bulk doping,and size reducing

In this work, a one-step solid-phase sintering process via TiO₂ and Li₂CO₃ under an argon atmosphere, with ultra-fine titanium powder as the modifying agent, was used to prepare a nano-sized Li₄Ti₅O₁₂/Ti composite (denoted as LTO–Ti) at 800 °C. The introduction of ultra-fine metal titanium powder played an important role. First, X-ray photoelectron spectroscopy demonstrates that Ti⁴⁺ was partially changed into Ti³⁺, through the reduction of the ultra-fine metal titanium powder. Second, X-ray diffraction revealed that the ultra-fine metal titanium powder did not react with the bulk structure of Li₄Ti₅O₁₂, while some pure titanium peaks could be seen. Additionally, the size of LTO–Ti particles could be significantly reduced from micro-scale to nano-scale. The structure and morphology of LTO–Ti were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Electrochemical tests showed a charge/discharge current of 0.5, 1, 5, and 10 C; the discharge capacity of the LTO–Ti electrode was 170, 161, 140, and 111 mAh g^?1. It is believed that the designed LTO–Ti composite makes full use of both components, thus offering a large contact area between the electrolyte and electrode, high electrical conductivity, and lithium-ion diffusion coefficient during electrochemical processes. Furthermore, ultra-fine titanium powder, as the modifying agent, is amenable to large-scale production.     

Integrated investigation of the Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> phase stability

The Li₄Ti₅O₁₂ is applied in lithium ion batteries as anode material, which can be synthesized by various synthesis techniques. In this study, the molten salt synthesis technique at low temperatures, i.e. 350 °C, was applied to synthesize Li₄Ti₅O₁₂. Surprisingly, the Li₄Ti₅O₁₂ was not formed according to XRD analysis, which raised question about the stability range of Li₄Ti₅O₁₂. To investigate the stability of Li₄Ti₅O₁₂ at low temperatures, the high-temperature calcined Li₄Ti₅O₁₂ powder was equilibrated in the LiCl-KCl eutectic salt at 350 °C. The result of experiment revealed that the Li₄Ti₅O₁₂ is not decomposed. Results of ab initio calculations also indicated that the Li₄Ti₅O₁₂ phase is a stable phase at 0 K. The products of molten salt synthesis technique were then annealed at 900 °C, which resulted in the Li₄Ti₅O₁₂ formation. It was concluded that the Li₄Ti₅O₁₂ is a stable phase at low temperatures and the reasons for not forming the Li₄Ti₅O₁₂ by molten salt technique at low temperature are possibly related to activation energy and kinetic barriers. The Li₄Ti₅O₁₂ formation energy is also very small, due to the results of ab initio calculations.     

Li4Ti5O12/Ag composite as electrode materials for lithium-ion battery

The Li₄Ti₅O₁₂/Ag composites were prepared by thermal decomposition of AgNO₃ added to Li₄Ti₅O₁₂ powders. The influence of the Ag contents and the mixing media on the particle size, morphology and electrochemical performance of Li₄Ti₅O₁₂/Ag composites were investigated. The highest discharge capacity of the Li₄Ti₅O₁₂/Ag composite reached at the 5 wt.% of Ag content. Compared with alcohol medium, distilled water as mixing medium presented the Li₄Ti₅O₁₂/Ag composite with higher specific capacity and better cycling performance, leading to a reversible capacity after 50 cycles of 184.2 mAh/g with a capacity degradation of 3.31% compared to the second cycle at 2 C rate.     

Surface nitridation induced high electrochemical performance of Li4Ti5O12 using urea as a nitrogen source

Surface nitridation of the Li₄Ti₅O₁₂ particles was carried out by thermal treatment with urea as the nitrogen source in a controllable manner. The titanium nitride (TiN) was formed in the well-dispersed zones on the surface of the Li₄Ti₅O₁₂ particles, depending on the coverage of the nitride. The surface TiN formed led to a great improvement of the conductivity of the oxide. The extent of the surface nitridation exhibited a large effect on electrochemical behaviors of the Li₄Ti₅O₁₂ particles, with the Li₄Ti₅O₁₂/TiN composite (prepared using 6 % urea) providing the best initial capacity and rate capability. Thus, the electrochemical performance of the Li₄Ti₅O₁₂ particles can be achieved by optimizing surface nitridation of the oxide. The chemically inert TiN occupied the surface sites of the Li₄Ti₅O₁₂ particles which may have prevented the electrolyte from decomposition and stabilized the surface structure of the Li₄Ti₅O₁₂ particles, endowing the oxide with excellent cycleability     

Development of monodispersed MnCO<Subscript>3</Subscript>/graphene nanosheet composite as anode for lithium-ion battery by hydrothermal synthesis

A unique monodispersed MnCO₃/graphene nanosheet composite is synthesized by a simple one-step hydrothermal method and used as anode of lithium-ion battery. X-ray diffraction patterns show the typical rhombohedral structure of MnCO₃. A transmission electron micrograph reveals that MnCO₃ is evenly distributed on the graphene nanosheet surface with a uniform diameter of 100 nm. Electrochemical performance results show that the specific discharge capacities of MnCO₃/graphene nanosheet composite remain above 1015.9 mAh g^?1 at a rate of 0.2 C after 85 cycles in the potential window of 0.01–2.0 V and even at a high rate of 1.0 C this parameter remains at 683.5 mAh g^?1 after 100 cycles. Thus, the composite also exhibits favorable rate performance. The excellent reversible capacities are attributed to the highly dispersed and large nanosheet structure of the composite, which may not only facilitate the fast transport of Li⁺ ions between the electrode and electrolyte but also provide enough surfaces to accommodate extra Li⁺ ions that contribute to partial interfacial storage capacities. Additionally, graphene nanosheet can effectively improve electrical conductivity of the composite. Therefore, MnCO₃/graphene nanosheet composite can be a great potential anode material for lithium-ion batteries.