Self organized nano crystallinity of magnetite precipitated from a 4.9Na2O · 33.3CaO · 17.1Fe2O3 · 44.7B2O3 glass

Glasses with the mol% composition 4.9Na₂O · 33.3CaO · 17.1Fe₂O₃ · 44.7B₂O₃ were melted, rapidly quenched using a twin roller technique, and subsequently tempered in the range from 550 to 620 °C. This led to the crystallization of magnetite with mean crystallite sizes in the 10-20 nm range. Using higher temperatures resulted in a larger quantity of formed crystallites and slightly larger mean crystallite sizes. Larger tempering times did not lead to substantial crystal growth. The time law of Ostwald ripening was not followed. This is explained by an increase in viscosity of the residual glassy phase during nucleation and crystal growth. Here, the smaller iron concentration near the crystals leads to higher viscosities and to the formation of a diffusional barrier around the crystals, which reduces further crystal growth. The crystallization stops, if T_g of the residual glassy phase is equal to the tempering temperature. Magnetite nano crystals with sizes in the 10-20 nm range offer a wide range of applications, such as the preparation of ferrofluids or of materials for medical diagnostics and therapy.     

Transition from a single-ion to a collective diffusion mechanism in alkali borate glasses

Two distinct regions of the dc conductivity and its temperature dependence as a function of the mol fraction of alkali oxides, X, are observed in Na- and Li-borate glasses. At low alkali contents the dc conductivity σ_dc increases only moderately with X. However, at higher alkali contents, log σ_dc increases linearly and the activation enthalpy ΔH of σ_dc × T decreases linearly with log X, i.e. the dc conductivity reveals an effective power-law behavior. The transition between low alkali and high alkali behavior takes place at X ≈ 0.08 for Na-borate and at X ≈ 0.09 for Li-borate glasses. This behavior suggests that the diffusion mechanism changes at these alkali contents. The results are discussed in terms of ion separations and the transition from a single-ion jump to a collective diffusion mechanism. The vanishing of the mixed-alkali peak in Na–Rb borate and alumino-germanate glasses at sodium contents similar to that observed for the change in slope of σ_dc(X) in this work suggests that both phenomena share the same origin.     

Sodium tracer diffusion in glasses of the type (Na2O)0.2(B2O3)y(SiO2)0.8 − y

Sodium tracer diffusion coefficients, D^?_Na, have been measured in sodium borosilicate glasses of the type (Na₂O)_0.2(B₂O₃)_y(SiO₂)_0.8−y as a function of temperature and the composition parameter y. At constant temperature, the tracer diffusion coefficient of sodium decreases as y increases. The activation enthalpy derived from sodium tracer diffusion data for temperatures up to about 350 °C increases about linearly with increasing values of y from about 70 to 100 kJ/mol. The pre-exponential factor of the sodium tracer diffusion coefficient as a function of y varies by about one order of magnitude and has a minimum at near y = 0.3.     

The comparative structure, properties, and ionic conductivity of LiI + Li2S + GeS2 glasses doped with Ga2S3 and La2S3

The well known and characterized fast ion conducting (FIC) LiI + Li₂S + GeS₂ glass-forming system has been further optimized for higher ionic conductivity and improved thermal and chemical stability required for next generation solid electrolyte applications by doping with Ga₂S₃ and La₂S₃. These trivalent dopants are expected to eliminate terminal and non-bridging sulfur (NBS) anions thereby increasing the network connectivity while at the same time increasing the Li⁺ ion conductivity by creating lower basicity [(Ga or La)S_4/2]⁻ anion sites. Consistent with the finding that the glass-forming range for the Ga₂S₃ doped compositions is larger than that for the La₂S₃ compositions, the addition of Ga₂S₃ is found to eliminate NBS units to create bridging sulfur (BS) units that not only gives an improvement to the thermal stability, but also maintains and in some cases increases the ionic conductivity. The compositions with the highest Ga₂S₃ content showed the highest T_gs of ∼325 °C. The addition of La₂S₃ to the base glasses, by comparison, is found to create NBS by forming high coordination octahedral LaS₆³⁻ sites, but yet still improved the chemical stability of the glass in dry air and retained its high ionic conductivity and thermal stability. Significantly, at comparable concentrations of Li₂S and Ga₂S₃ or La₂S₃, the La₂S₃-doped glasses showed the higher conductivities. The addition of the LiI to the glass compositions not only improved the glass-forming ability of the compositions, but also increased the ionic conductivity glasses. LiI concentrations from 0 to 40 mol% improved the conductivities of the Ga₂S₃ glasses from ∼10⁻⁵ to ∼10⁻³ (Ω cm)⁻¹ and of the La₂S₃ glasses from ∼10⁻⁴ to ∼10⁻³ (Ω cm)⁻¹ at room temperature. A maximum conductivity of ∼10⁻³ (Ω cm)⁻¹ at room temperature was observed for all of the glasses and this value is comparable to some of the best Li ion conductors in a sulfide glass system. Yet these new compositions are markedly more thermally and chemically stable than most Li⁺ ion conducting sulfide glasses. LiI additions decreased the T_gs and T_cs of the glasses, but increased the stability towards crystallization (T_c − T_g).     

Occurrence of Kondo-like behavior in electrical-conductivity of Al70Pd20+xMn10−x (x = 0, 1 and 2) icosahedral quasicrystals

Zero-field and in-field (at 8 T) conductivity vs temperature (σ-T), magneto-resistance (Δρ/ρ), magnetization vs temperature (M-T) and magnetization vs field (M-H) of unannealed Al₇₀Pd₂₀Mn₁₀ and annealed Al₇₀Pd₂₀Mn₁₀, Al₇₀Pd₂₁Mn₉ and Al₇₀Pd₂₂Mn₈ quasicrystalline alloys have been studied in the temperature range of 1.4-300 K. Room temperature resistivity and the low-temperature magneto-resistance show a correlation with the corresponding magnetization. The σ-T for all the studied samples shows a pair of minima and maxima. The σ-T maxima show a correlation with the total magnetization. The analysis shows that σ-T is dominated by weak-localization effects. The minima are arising due to competing inelastic scattering times τ_i (e-ph scattering in the dirty metallic limit, τ_i ∝ T⁻²) and the Kondo-type spin-flip scattering time τ_sf whereas the maxima has been attributed to ‘Kondo-maxima’, occurring due to maxima in the spin-flip rate . The magneto-resistance of these samples shows a changeover from negative to positive where the negative component shows a correlation with the magnetization of the sample. The values of parameters derived from refinement give spin-flip scattering fields, which are found to be correlated with the total sample magnetization.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

Transport property and structural characterization studies on (1 − x)[0.75AgI:0.25AgCl]:xTiO2 conducting composite electrolyte system

Transport property and structural investigation have been carried out on newly synthesized Ag⁺ ion conducting composite electrolyte system. The composite electrolyte system (1 − x)[0.75AgI:0.25AgCl]:xTiO₂, where 0 ? x ? 0.5 (in molar weight fraction) has been synthesized by melt quenching and annealing methods. The chemical compound TiO₂ (second phase dispersoid) dispersed in different compositions in a quenched (0.75AgI:0.25AgCl) mixed system/solid solution; this solid solution was used as a first phase host salt in place of AgI. The different preparation routes were adopted for the composite electrolyte system. Composition x = 0.1 exhibited highest conductivity at room temperature. The composite system 0.9[0.75AgI:0.25AgCl]:0.1TiO₂ was synthesized at different soaking times by melt quenching method. The system exhibited optimum conductivity at 20 min soaking time (σ_rt ≈ 1.4 × 10⁻³ S/cm). The ac conductivity has been measured from Z′-Z″ (Cole-Cole) complex impedance plots using impedance spectroscopic (IS) technique. The electrical conductivity as a function of temperature and frequency has been studied, and activation energy E_a, was calculated from Arrhenius plots for all compositions (0 ? x ? 0.5). The dc conductivity value has been evaluated from Log σ vs. log f plots. Structural characterization studies were carried out by X-ray diffraction (XRD) and differential thermal analysis (DSC) techniques.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.     

Optical properties of Cr ion in lithium metasilicate Li2O · SiO2 transparent glass-ceramics

The optical properties of Cr³⁺ ions in lithium metasilicate (Li₂O · SiO₂) transparent glass-ceramics were investigated. The main crystalline phase precipitated was the lithium metasilicate (Li₂O · SiO₂) crystal. The percent crystallinity and crystalline size were ranging 65-75% and 20-35 nm, respectively. The color changes drastically to deep pink from emerald green upon crystallization. New and strong absorption bands appeared and the absorption intensity increases by about 10 times that in glass. These new absorption bands are found to be derived from Cr³⁺ ions in octahedral sites in the lithium metasilicate crystal lattice. Cr³⁺ ions substitute for three Li⁺ ions and occupy the distorted octahedral site between single [SiO₄]_n chains of lithium metasilicate crystal. The ligand field parameters can be estimated: 10Dq = 13 088 cm⁻¹, B = 453 cm⁻¹, Dq/B = 2.89 and C = 2036 cm⁻¹. The near-infrared luminescence centered at 1250 nm was not detected in the deep pink glass-ceramics unlike emerald green glass.     

Sodium tracer diffusion in glasses of the type (Na2O)0.2[(BO1.5)x(SiO2)1 − x]0.8

Sodium tracer diffusion coefficients, D_Na*, have been measured in sodium borosilicate glasses of the type (Na₂O)_0.2[(BO_1.5)_x(SiO₂)_1 − x]_0.8 as a function of temperature and the composition parameter x. In these glasses, which can alternatively also be described by using the formula Na₂O·(2B₂O₃)_x·(4SiO₂)_1 − x, one network former unit, SiO₂, is replaced by another one, BO_1.5, while keeping the sodium concentration constant. At constant temperature, the tracer diffusion coefficient of sodium as a function of x has a shallow minimum at about x = 0.7. At temperatures below about 310 °C the temperature dependences of the measured tracer diffusion coefficients are of Arrhenius-type; at higher temperatures one observes an increase in the temperature dependence with increasing temperature. The activation energy derived from sodium tracer diffusion data for temperatures up to about 310 °C increases about linearly with increasing x from about 70 to 80 kJ/mol. The pre-exponential factor as a function of x varies by about one order of magnitude and has a minimum at about x = 0.4. Values derived for the Haven-ratio are smaller than one and show a shallow minimum as a function of x at around x = 0.75. Furthermore, it was investigated whether there is a significant, directly measurable uptake of water during annealing in moist atmospheres and whether water taken up from moist atmospheres can influence the diffusion of sodium.     

Vibrational, EPR and optical spectroscopy of the Cu doped glasses with (90-x)TeO2-10GeO2-xWO3 (7.5 ≤ x ≤ 30) composition

Infrared, EPR and optical absorption studies on (90-x)TeO₂-10GeO₂-xWO₃ (7.5 ≤ x ≤ 30) glasses containing Cu²⁺ spin probe have been carried out. The Infrared spectral studies show that the structure of glass network consists of [TeO₄], [TeO₃]/[TeO_3 + 1], [WO₄], [WO₆] and [GeO₆] units in the disordered manner. Physical parameters such as density (ρ), molar volume (V_m), oxygen packing density (OPD), oxygen molar volume (V_o), optical basicity (Λ), oxide ion polarizability (α_O²⁻), inter ionic distances and the concentration of ions per unit volume of Te, Ge, W, Cu and O have been determined. The spin-Hamiltonian parameters (g_||, g_⊥ and A_||) of Cu²⁺ ions in the present glasses have been estimated from EPR spectra at 300 K. Bonding parameters such as α², β₁², β², Γ_σ, and Γ_π have been calculated from both optical absorption and EPR data. The observed variations in spin-Hamiltonian parameters and bonding parameters have been correlated to the structural modifications due to the WO₃ incorporation into the TeO₂ glass network at constant 10 mol% GeO₂ content.     

Spectrometric and ellipsometric studies of (1 − x)TiO2 · xLn2O3 (Ln = Nd, Sm, Gd, Er, Yb) thin films

Spectrometric and ellipsometric studies of (1 − x)TiO₂ · xLn₂O₃ (Ln = Nd, Sm, Gd, Er, Yb; x = 0.33, 0.5) thin films at room temperature were performed. The obtained dispersion dependences of refractive indices are successfully described by the optical-refractometric relation. The dependence of optical pseudogap and refractive indices on composition and molar mass of the films is investigated. The influence of compositional disordering on the energy width of the exponential absorption edge is studied.     

Thermodynamical miscibility in 0.8[xB2O3-(1 − x)P2O5]-0.2K2O glasses

The thermodynamical miscibility in 0.8[xB₂O₃-(1 − x)P₂O₅]-0.2K₂O glasses has been studied by measuring the glass transition temperature and the mixing enthalpy. Measurements have been performed by differential scanning calorimeter and hydrofluoric acid solution calorimetry at 298 K. The enthalpies of mixing are significantly negative over the whole range of composition. The results are discussed in terms of intermolecular associations.     

Effect of pressure on the refractive index and relative density of the CaO · Al2O3 · 6SiO2 glass

The refractive index for glass of the CaO · Al₂O₃ · хSiO₂ system with х = 6 in the range of pressures up to 6.0 GPa was measured using a polarization-interference microscope and an apparatus with diamond anvils. The changes in the relative density characterizing the compressibility of glass were estimated from the measured refractive indices within the framework of the theory of photoelasticity. The data were compared with the previous data for glasses of the same system with х = 2 and 4. The most compressible of the three glasses in the range 2.0-6.0 GPa was the CaO · Al₂O₃ · 6SiO₂ glass. For glasses with х = 2, 4 and 6 we calculated the degrees of polymerization of silicon-aluminum-oxygen network, NBO/T (NBO - non-bridging oxygen), which are determined as the ratio of the number of gram-ions of non-bridging oxygen atoms to the total number of gram-ions of network formers. The structure-chemical parameter NBO/T was calculated with due regard for the formation of triclusters and highly coordinated aluminum. The degree of polymerization of the CaO · Al₂O₃ · хSiO₂ glasses increases with increasing х, which agrees with the change of their relative density under pressure.     

Three-dimensional structure of fast ion conducting 0.5Li2S + 0.5[(1 − x)GeS2 + xGeO2] glasses from high-energy X-ray diffraction and reverse Monte Carlo simulations

A high-energy X-ray diffraction study has been carried out on a series of 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses with x = 0.0, 0.1, 0.2, 0.4, 0.6 and 0.8. Structure factors were measured to wave vectors as high as 30 Å⁻¹ resulting in atomic pair distribution functions with high real space resolution. The three dimensional atomic-scale structure of the glasses was modeled by reverse Monte Carlo simulations based on the diffraction data. Results from the simulations show that at the atomic-scale 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses may be viewed as an assembly of independent chains of (Li^+-S)₂GeS_2/2 and (Li^+-O)₂GeO_2/2 tetrahedra as repeat units, where the Li ions occupy the open space between the chains. The new structure data may help understand the reasons for the sharp maximum in the Li⁺ ion conductivity at x ∼ 0.2.     

Spectroscopic properties of Er-doped xGeO2-(80 − x)TeO2-10ZnO-10BaO glasses

Erbium-doped glasses with composition xGeO₂-(80 − x)TeO₂-10ZnO-10BaO were prepared by melt-quenching technique. The phonon sideband spectra and the optical absorption band edges for the host matrix were confirmed by means of the spectral measurements. Standard Judd-Ofelt calculations have been completed to these glasses. The dependence of up-conversion and infrared emission under 980 nm excitation on the glass composition was studied. The quantum efficiencies for the ⁴I_13/2 → ⁴I_15/2 transition of trivalent erbium in the glasses were estimated.     

Insulator-like electrical transport in structurally ordered Al65Cu20+xRu15−x (x = 1.5, 1.0, 0.5, 0.0 and −0.5) icosahedral quasicrystals

Low-temperature resistivities, in zero-field and 8 T field, and magnetoresistance have been measured down to 1.4-300 K for stable icosahedral quasicrystals Al₆₅Cu_20+xRu_15−x (x = 1.5, 1.0, 0.5, 0.0 and −0.5). The analysis of the magnetoresistance data shows an overwhelming presence of anti weak-localization effect (τ_so ∼ 10⁻¹² s). But the sample with x = −0.5 shows anomalous magnetoresistance and the anti weak-localization effect breaks down (τ_so to be 10⁻¹⁵ s). The in-field σ-T between 5 K and 20 K, for x = 1.0, 0.5, 0.0 and −0.5 samples, and between 1.4 K and 40 K for x = 1.5 sample, follow a power-law behavior with an exponent of 0.5 and above ∼30 K the exponent ranges from 1.17 to 1.58. The observed power-laws basically characterize the presence of critical regime of the metal-insulator (MI) transition, dominated by electron-electron and electron-phonon inelastic scattering events respectively. In samples with x = 1.0, 0.5, 0.0 and −0.5 the in field σ-T has been found to follow ln σ-vs-T^1/4 below 5 K, which indicates the presence of variable range hopping. The observed transport features indicate the occurrence of proximity of metal-insulator transition in these Al-Cu-Ru quasicrystal samples.     

The dielectric behavior of a thermoelectric treated B2O3-Li2O-Nb2O5 glass

A transparent glass with the composition 60B₂O₃-30Li₂O-10Nb₂O₅ (mol%) was prepared by the melt-quenching technique. Glass-ceramics, containing LiNbO₃ ferroelectric crystallites, were obtained by heat-treatment (HT) above 500 °C, with and without the presence of an external electric field. The dielectric properties of the glass and glass-ceramic were investigated, as a function of temperature (270-315 K), in the 10 mHz-32 MHz frequency range. The presence of an external electric field, during the heating process, improves the formation of LiNbO₃ crystallites. The rise of the treatment temperature and the applied field, during the heat-treatment, leads to a decrease in the dc electric conductivity (σ_dc), indicating a decrease of the charge carriers number. The dielectric permittivity (ε′) values (300 K;1 kHz) are between 16.25 and 18.83, with the exception of the 550 °C HT sample that presents a ε′ value of 11.25. An electric equivalent circuit composed by an R in parallel with a CPE element was used to adjust the dielectric data. The results reflect the important role carried out by the heat-treatment and the electric field during the HT in the electric properties of glass-ceramics.     

Increase in the Fluorine-Ion Conductivity of Single Crystals of Tysonite-type CeF<Subscript>3</Subscript> Superionic Conductor by Substituting Polarized Cd<Superscript>2+</Superscript> Ions for Ce<Superscript>3+</Superscript> Ions

The fluorine-ion conductivity of single crystals with a tysonite (LaF₃) structure with heterovalent isomorphic substitutions of highly polarizable Cd²⁺ cations with a 18-electron shell for rare earth ions Ce³⁺ have been studied for the first time. Ce_0.995Cd_0.005F_2.995 single crystals have been grown from melt by the Bridgman technique in a fluorinating atmosphere. The fluorine-ion conductivity of single crystal is measured by impedance spectroscopy in the temperature range from 153 to 1073 K, where it increases by a factor of 10⁹, approaching the value σ_dc = 5 × 10^–2 S/cm at 1073 K. At T₀ = 450 ± 20 K, the dependence σ_dc(T) is split into two portions with the ion-transport activation enthalpy ΔH_σ = 0.39 ± 0.01 eV (T < T₀) and ΔH_σ = 0.23 ± 0.02 eV (T > T0). It is found that at T = 293 K the conductivity σ_dc = 3 × 10^–5 S/cm of Ce_0.995Cd_0.005F_2.995 crystal is higher by a factor of 10 than the conductivity of the tysonite matrix CeF₃ and close to the σ_dc value for Ce_0.995Sr_0.005F_2.995 crystal. This finding indicates a significant effect of the substitutions of Cd²⁺ ions for Ce³⁺ on the σdc value and the advantage of Cd²⁺ ions over Ca²⁺ and Ba²⁺ from the viewpoint of increasing σ_dc.